Scribd
Upload
317 views4 pages

Experiment No. 2 Clipping and Clamping Circuits AIM

The document describes different types of clipping and clamping circuits. It defines clipping circuits as nonlinear wave shaping circuits that cut off portions of an input waveform. Positive and negative clipper circuits are described that clip either the positive or negative half cycles, respectively, using a diode. Biased positive and negative clipper circuits add a reference voltage to clip only part of the cycle. A slicer circuit combines both types of biased clippers. Clamping circuits add a positive or negative DC level to clamp an input signal to a reference voltage. The procedure explains how to set up and observe the different circuits using a function generator and oscilloscope.

Uploaded by

conference Requirements
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
317 views4 pages

Experiment No. 2 Clipping and Clamping Circuits AIM

The document describes different types of clipping and clamping circuits. It defines clipping circuits as nonlinear wave shaping circuits that cut off portions of an input waveform. Positive and negative clipper circuits are described that clip either the positive or negative half cycles, respectively, using a diode. Biased positive and negative clipper circuits add a reference voltage to clip only part of the cycle. A slicer circuit combines both types of biased clippers. Clamping circuits add a positive or negative DC level to clamp an input signal to a reference voltage. The procedure explains how to set up and observe the different circuits using a function generator and oscilloscope.

Uploaded by

conference Requirements
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Experiment No.

2
CLIPPING AND CLAMPING CIRCUITS
AIM
To realise different clipping and clamping circuits and observe the waveforms.
THEORY
Clipping Circuits
Clipping circuits are nonlinear wave shaping circuits. A clipping circuit is useful to cut
off the positive or negative portions of an input waveform. Clipping circuits are also known as
voltage limiters or slicers.
Positive clipper
The positive half cycle is clipped by diode and only the drop across diode will appear
across the load. During negative half cycle, the diode does not conduct and the voltage across
RL is given by

RL
VL  VS
RL  R

Since RL >> R, the output voltage will be close to input voltage during negative half
cycle.
Negative clipper
The negative half cycle is clipped by diode and only the drop across diode will appear
across the load. During positive half cycle, the diode does not conduct and the voltage across
RL is given by

RL
VL  VS
RL  R

Since RL >> R, the output voltage will be close to input voltage during the positive half
cycle.
Biased positive clipper
Here a reference voltage is given to the clipper circuit by a zener diode. Up to Vz, the
output voltage is

V0 = Vin RL /(RL+R)
At Vo = Vz, the zener breakdown occurs and the voltage Vo is constant. Here the reference
voltage is used to clip only a part of the positive half cycle.

Electronic Circuits Lab, Department of Electrical Engineering, College of Engineering Trivandrum 1


Biased negative clipper
The principle is similar to that of a biased positive clipper. Here a reference voltage is
provided by a zener diode to clip a portion of the negative half cycle. During the positive half
cycle

V0 = Vin RL/(RL+R)
Slicer
This is the combination of both biased positive clipper and biased negative clipper. The
peak portion of the signal determined by the zener voltage reference is clipped.
Clamping Circuit
Clamping is a function which must be frequently performed with a periodic waveform
in the establishment of the recurrent positive or negative extremity at some constant reference
level. Clamping circuits are also referred to as dc restorer or dc inserter.
A positive clamper adds positive dc level and a negative clamper adds a negative dc
level. A positive clamper clamps a negative extremity of the input signal to the reference
voltage level. A negative clamper adds to negative dc level by clamping the positive extremity
of the input to the reference voltage level.
PROCEDURE
The circuits are wired as in the circuit diagram. Connect the input terminals to 230V ac
supply and the output terminals to a CRO.

Positive clipper

Negative clipper

VS
t

0.6 V
VL

Electronic Circuits Lab, Department of Electrical Engineering, College of Engineering Trivandrum 2


Biased Positive clipper
VS
t

VL VZ+VD

Biased Negative clipper

Slicer

Electronic Circuits Lab, Department of Electrical Engineering, College of Engineering Trivandrum 3


Positive clamping Circuit
C 1 uF
+

D1 RL
230 V AC 1N4007 100 k CRO

230/6V

Negative clamping Circuit


C 1 uF
+

D1 RL
230 V AC 1N4007 100 k CRO

230/6V

Electronic Circuits Lab, Department of Electrical Engineering, College of Engineering Trivandrum 4

You might also like