8 7 6 5 4 3 2 1

REVISION HISTORY
REV DESCRIPTION INCORP BY DATE CHECKED
2 Added strap button and grounding wire holes. N/A 10MAY2011 N/R

3 (10 plcs) 1
H 5 Ø32 R12 4 H
16

Neck Binding 11
116
119
32
0.020 x 0.250 x 18
5 Min.
(2 plcs + end)
7 64
8 Maple Filler
0.023 Wide
Blend (binding) edge Fret Slot
211 3
16 4 Ø83 1
216 123
32
Ø212 (12 plcs)

112 Ø312 225

32 1.000 0.900
G 1
R116 R78 1st Fret
G
Ø12 (2 plcs) 12th Fret Overlay 1st
Ø12 (4 plcs) Girth: 3.11 and 12th Fret
Girth: 2.73
Waist: 5.15 Waist: 4.45
7 Tap 6-32 (2 plcs) Neck Heel Detail 9
Ø64 16
121 481
Epi length (19th fret) 238 Headstock ear (2 plcs)
7 (2 plcs)
Ø16
12.281

4 341 229 7
116 2.1035 in 1.50 1.75
32
F F

19 1/4" MOP Dot (10 plcs)

132 1.375
Ø23
64 (6 plcs)
Ø38 Ø18 (GND) for Kluson
TPKR3-N
7 in
Ø16

NOTES:
1 1 1
Ø11
32 in (4 plcs)
1. Top and back plates' plies are maple, basswood (cross-grain), and maple (16, 10, 16).
1
E 2. Rim plies are 16 maple, basswood (cross-grain), and maple. E
3. Top view shows fret board, headstock, pickguard in fabricated planes to reflect their true size.

4. Add material to create a smooth surface using elevations shown in laminate template.

5. F-holes and control layout for use with a pin router.

1 3
6. Neck is quarter-sawn mahogany (blank 2 2 (fretboard surface) x 2 4 (parallel to grain) x 26).
Kerfing - 7/32 x 9/16 x 31 (4 plcs)
Maple Centerblock 7. Kerfing is mahogany, spruce, or basswood.
Binding - 0.060 x 0.250 x 62 (2 plcs)
8. Girth - to edges of playing surface. Waist - girth and playing surface perimeter.
Spruce - Kerf 0.025, 1/4 Centers (2 plcs)

D 0.447 D
0.225 24.687 Nut to Treble Post
24.625
3
5
116 1 16
3
4 94°0' 1.000
88° 112
143 3 (2 plcs)
Ø32 5
116 1 Spruce Stock
3 2 0.900 17°
4°0'
16 R141 Truss Rod Channel
0.250 wide, 0.400 deep
5
Mahogany Tailblock 16 (dependent on truss rod used) R6
Cover with maple filler strip.

0.060 Holly Veneer

C Jig Indexing Pins (6 plcs) C
1814
5
8
1
116

*+,#+
' ()

#+

*- .-

B B
8.0

! " #
$ % " #&

UNLESS OTHERWISE SPECIFIED TITLE

DIM ARE IN INCHES
Curve Length 30.57 TOL ON ANGLE ± 0° 30' 335 / DOT CONSTRUCTION
.XX ± .03 .XXX ± .010
INTERPRET DIM AND TOL PER Copyright (c) 2010 by Pat Sharkey. This work is licensed under the
ASME Y14.5M - 1994
DO NOT SCALE DRAWING Creative Commons Attribution-NonCommercial-NoDerivs 3.0
Unported License. To view a copy of this license, visit
THIRD ANGLE PROJECTION http://creativecommons.org/licenses/by-nc-nd/3.0/ or send a letter to
A Creative Commons, 171 Second Street, Suite 300, San Francisco,
California, 94105, USA.
A
SIZE REV

E 2
SCALE 1:1 SHEET 1 of 1
8 7 6 5 4 3 2 1