Scribd
Upload
448 views9 pages

MT1Z User Manual V1.0 - 58.64.205.22

The document provides instructions for setting up and using an MT-1Z GPS tracker. It describes the tracker's specifications, wiring connections, LED light statuses, important notices, detailed operation instructions through commands, and how to track the device online using a 900D web-based tracking software. The summaries are: 1. The MT-1Z GPS tracker has specifications including an MTK GSM module, U-Blox GPS chipset, operating temperature range, battery voltage, and dimensions. 2. Wiring instructions and an anti-jammer function are described. 3. Commands are provided to control the tracker, including setting controller numbers, work modes, passwords, location requests, reports, geo-

Uploaded by

Devendra Gonsalves
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
448 views9 pages

MT1Z User Manual V1.0 - 58.64.205.22

The document provides instructions for setting up and using an MT-1Z GPS tracker. It describes the tracker's specifications, wiring connections, LED light statuses, important notices, detailed operation instructions through commands, and how to track the device online using a 900D web-based tracking software. The summaries are: 1. The MT-1Z GPS tracker has specifications including an MTK GSM module, U-Blox GPS chipset, operating temperature range, battery voltage, and dimensions. 2. Wiring instructions and an anti-jammer function are described. 3. Commands are provided to control the tracker, including setting controller numbers, work modes, passwords, location requests, reports, geo-

Uploaded by

Devendra Gonsalves
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

User Manual

MT-1Z GPS Tracker


(Vehicle/Motorcycle)

Version:X

1. Specification
GSM module MTK program, GSM 850/900/1800/1900
Support TCP protocol
GPS Chipset U-BLOX 7020(Support GPS/Glonass/Galileo/Compass)
GPS sensitivity -162dB
Hot start 1sec.,average
Warm start 30 sec.,average
Cold Start 35 sec, average
Operating temperature -20°C－65°C
Battery Volume 50mAh
Dimension 89mm×51mm×15mm
Voltage 12-100V
Altitude Limit 18,000 meters (60,000feet) max.

2. Wiring connections
Red (+)12V -24V
Black GND(-)
Yellow NULL
Orange ACC
How the anti-jammer function work:

Wire like above, make sure acc cable is connected, if GPS tracker detects Jammer signal, the
wirelsss relay will cut car engine after 1 minute, then the thief can not start the car engine.

3.Led light description


Blue LED Light--- GPS Status
Status Meaning
Flash No gps signal, or searching for gps signal
Always on GPS Signal ok

Orange LED Light---GSM Status


Status Meaning
Flash No sim card, or searching for gsm signal
Always on GSM Signal ok

Red LED Light--- Work status


Status Meaning
Flash Working

Not on Power off or sleep

4. Important Notice:
1. This tracker have two work mode which is SMS and GPRS Mode. SMS mode is for off line
tracking by Mobile phone. GPRS Mode is for on line tracking by computer and mobile phone .
2. Default password 0000
4. Main power off alarm: Device will send alert sms to the 3 controller phone number, and call
the first controller number
Geo-fence alarm: Device will send alert sms and call the first controller number.
Over speed alarm: Device will send alert sms and call the 3 controller phone numbers.
Shock alarm: Device will send alert sms to the first controller phone number.
Low battery alert: Device will send alert sms to the first controller phone number.
ACC alarm: Device will send alert sms to the 3 controller phone number, and call the first
controller number.

5. Detail Operation
1. Controller phone number
Command: controller phone number+ user password +space+Sequence number (1-3)
Eg: 158111122220000 1
Reply : SET USER NUMBER 1 OK.
Eg: 168111122220000 2
Reply : SET USER NUMBER 2 OK
Eg: 178111122220000 3
Reply : SET USER NUMBER 3 OK

Note: 1. Tracker can have three pre-saved number


2. New Number can cover the old number
3. No pre-saved number also can control the tracker, but alarm information only to pre-saved
number

2. Work Mode Exchange :


SMS Mode Command：700+ user password
Eg: 7000000
Reply: SET MODE OK, CURRENT MODE: SMS
GPRS Mode Command：710+ user password
Eg: 7100000
Reply: SET MODE OK, CURRENT MODE: GPRS
3. Change user password
Command: 777+new password +old password (4 figures)
Eg: 77712340000
Reply: SET USER PASSWORD OK
4. Request the single position
Command: 666+ user password
eg: 6660000
Reply: when the tracker receive the command, then will send the position with longitude and
latitude
5. Request location with Google map URL link
Command : 669+ user password
Eg: 6690000
Command: Reply : When the tracker receive the command, tracker will send a Google link to the
sender

6. Command Get Daily report:


Command : 665+ user password+HHMM
Example：66500001022
Reply：SET DAILY REPORT OK
Note: HH stands for hour with defined range of [00, 23]. MM stands for minute with defined
range of [00, 59].

Close daily report function: 665+password+OFF（Default）


Example：6650000OFF
Reply：SET DAILY REPORT OFF

7. Geo- Fence
Turn On Geo-fence
Command: 211+ password
Eg: 2110000
Reply: GEO-FENCE ON
Set Geo Fence Command: 005+user password+Space+R
E.g: 0050000 1000
Reply: GEOFENCE ON
R=Geo-fence radius, in the unit of meter, for accuracy reason, better more than 1000meter.
1000 means geo-fence radius is 1000meter

Turn geo-fence off


Command: 210+ password
Eg: 2100000
Reply: GEO-FENCE OFF
8. Battery low voltage alert
While device detect internal battery is low power, it will send coordinate message with
STATE:LOW P OWER
9 .Alert while power off
Open the power off alert Command: 011 + user password
eg: 0110000
Reply: POWER ALARM ON
Close the power off alert Command: 010 + user password
eg: 0100000
Reply: POWER ALARM OFF

10. Power cut


Cut power: 940+password
Eg: 9400000
Enable power: 941+password
Eg:9410000

11. Mileage Statistics(Software Support)


Set initial mileage value (zero clearing)
Command: 142+PW<+M+X>
Eg : 1420000
Reply : MILEAGE STATISTICS RESET OK
Eg : 1420000M1000
Reply : SET TOTAL MILEAGE OK,CURRENT：1000
Note: M is delimiter, X is initial mileage value with unit of meter
Read current mileage
Command: 143 + user password.
eg: 1430000
Reply : MILEAGE STATISTICS:ON，CURRENT TOTAL MILEAGE:XX.
12. Time Zone
Command: 896 + user password + D + NN
Eg: 8960000E08
Reply : TIME ZONE SET OK,CURRENT：E8.
Note : D takes E or W to indicate east or west time zone respectively. N takes a 2-digit number
(1-12) to indicate time zone
number.
13. Overspeed Alarm
Command : 122+user password+space+X
Eg: 1220000 120
Reply: SET RATE LIMIT:120
Close command : 1220000 0
Note : X is speed benchmark value, which is an integral number. unit is KM/H with defined
domain of [0, 999].
14. Tow alarm
Turn on tow truck alert: 181 + user password + TX
Eg: 1810000T15 (15 seconds)
Reply : TOWED ALERT ON
Turn off tow truck alert: 180 + user password
Eg: 1800000
Reply : TOWED ALERT OFF
Note: X is the continuous time, the wide is 【15，100】, the unit is second
15. Set Defence Alarm ON/OFF
Set Up Defence：712+password
Eg：7120000
Reply：SF OK
Set Down Defence：713+password
Eg： 7130000
Reply：CF OK
16. Set ACC alarm:
Turn on acc alarm SMS: 886+user password
Eg: 8860000
Turn off acc alarm SMS: 887+user password
Eg: 8870000
Turn on acc alarm phone call: 888+user password
Eg: 8880000
Turn off acc alarm phone call: 889+user password
Eg: 8890000

17. Sleep Mode:


Turn on sleep mode:
SLEEP+user password+space+X
X means sleep time, from 1-720, in the unit of minute. If device not receive any command or
move at the X time you set, device will close GPS,GSM module, and be in power saving mode.
Eg：SLEEP0000 1
Reply：SET OK
Turn off sleep mode:
SLEEP+user password+space+0
Eg：SLEEP0000 0
Reply：SET OK

18. Set Access Point Name (APN)


Command1： 803+user password+space+APN
eg：8030000 CMNET
Command2 : 803+user password+space+APN+space+APN user name+space+APN Password
Reply: SET GPRS APN OK
19. Set server IP address and Port
Command： 804+user password+space+IP+space+Port
Eg: 8040000 58.64.205.22 8000
Reply: SET SERVER IP AND PORT OK
18. Set Data upload interval time
Command：805+user password+Space+X
Eg： 8050000 20
Reply: SET OK
Device will upload location to platform every 20 seconds when car acc is on.

Command：809+user password+Space+X
X is the location upload interval when car acc off, in the unit of seconds.
Eg： 8090000 60
Reply: SET OK
Device will upload location to platform every 20 seconds when car acc is off.
Note : X is mean interval time, the unit is seconds，the wide is 【1，1800】
We suggest X be no more than 480 seconds to avoid gprs traffice jam.

Specail Command :
1、Reset Command : RESET
2、Restart Command RESTART
3、Read the current setup information Command: RCONF

Track by 900D web based tracking software Setup.


Please follow above commands to set ip,port(IP is 58.64.205.22, port 8000), and APN, data
upload interval.

Then please go to http://www1.igpstracking.net/


Enter the user name and password we provided. After log in, please go to “User Center-Asset
Manage”, click “Add”
Asset Name: Define by yourself; you can enter A-Z number or Numeric

Very Important Note: Terminal ID and Plate number are unique on the software, you can add
once only, you need to delete it from database before adding it again. Only admin account can
delete id from database, general user cannot. You do not need to delete and re-add if the device
cannot work on software, because it's caused by your wrong sms setting, not the software.

Create time: Do not choose.

Activation time: Do not choose.

Expiry time: Define via yourself.

Forwarding type: Null

SIM card: the SIM card phone number you put in MT-1 or any number.

Device ID: On the vehicle of MT-1, you can find the “Device ID”.

Asset Password: define by yourself.

Click "Submit", and then you add the GPS tracker MT-1 successfully on the software 900D.

Wait few seconds, and you will see the GPS Tracker online icon on software
Put a check mark on the device, and right click, you will see the menu as below picture. Now you
can track online.

Put a check mark on the device, and right click, you will see the menu as below picture. Now you
can track online.

Attention: For 900D GPS Software, "Monitor" and "Number Plate" must be checked till the
font becomes blue, then the GPS tracker will update location automatically on map.Like
below picture:

Contacts
If you encounter any problems when using our products, and cannot solve them by yourself,
please contact our technical support team by writing an E-Mail to us. We will be pleased to help
you.

You might also like