TRAINING

REGULATIONS

GAS METAL ARC

WELDING (GMAW) NC III
METALS AND ENGINEERING SECTOR

TECHNICAL EDUCATION AND SKILLS DEVELOPMENT AUTHORITY

East Service Road, South Superhighway, Taguig City, Metro Manila
 TABLE OF CONTENTS

METALS AND ENGINEERING SECTOR

GAS METAL ARC WELDING (GMAW) NC III

Page No.

SECTION 1 GAS METAL ARC WELDING (GMAW) NC III 2

QUALIFICATION

SECTION 2 COMPETENCY STANDARDS 3-54

 Basic Competencies 3-21

 Common Competencies 22-48
 Core Competencies 49-54

SECTION 3 TRAINING STANDARDS 55-62

3.1 Curriculum Design 55-58

3.2 Training Delivery 59
3.3 Trainee Entry Requirements 60
3.4 List of Tools, Equipment and Materials 60-61
3.5 Training Facilities 61
3.6 Trainers' Qualifications 62
3.7 Institutional Assessment 62

SECTION 4 NATIONAL ASSESSMENT AND 63

CERTIFICATION ARRANGEMENTS

COMPETENCY MAP 64

DEFINITION OF TERMS 65

ACKNOWLEDGEMENTS 66

Weldncii11-3 1
 TRAINING REGULATIONS FOR
GAS METAL ARC WELDING (GMAW) NC III

SECTION 1 GAS METAL ARC WELDING GMAW NC III

The Gas Metal Arc Welding (GMAW) NC III Qualification consists of

competencies that a person must achieve to weld alloy steel plate and alloy steel
pipe components as specified by layout, blueprints, diagrams, work order, welding
procedure or oral instructions using GMAW welding equipment.

This Qualification conforms with American Welding Society (AWS) D 1.1

Structural Welding Code; American Society of Mechanical Engineers (ASME) IX
Boiler and Pressure Vessel Code; American Petroleum Institute (API) 1104 Code for
Gas and Oil Pipeline Facilities; and International Standards Organization (ISO) 9606-
1 Qualification of Welders for Steel.

The Units of Competency comprising this qualification include the following:

Code No. BASIC COMPETENCIES
5 00 311 1 09 Lead workplace communication
5 00 311 1 10 Lead small teams
5 00 311 1 11 Develop and practice negotiation skills
5 00 311 1 12 Solve problems related to work activities
5 00 311 1 13 Use mathematical concepts and techniques
5 00 311 1 14 Use relevant technologies

Code No. COMMON COMPETENCIES

MEE721201 Apply Safety Practices
MEE721202 Interpret Drawings and Sketches
MEE721203 Perform Industry Calculations
MEE721204 Contribute to Quality System
MEE721205 Use Hand Tools
MEE721206 Prepare Weld Materials
MEE721207 Setup Welding Equipment
MEE721208 Fit up Weld Materials
MEE721209 Repair Welds

Code No. CORE COMPETENCIES

MEE721314 Weld Alloy Steel Plates Using GMAW
MEE721318 Weld Alloy Steel Pipes Using GMAW

A person who has achieved this Qualification is competent to be:

- Plate Welder (GMAW) - GMAW Welder (Alloy Plate)
- Pipe Welder (GMAW) - GMAW Welder (Alloy Pipe)

Weldncii11-3 2
SECTION 2 COMPETENCY STANDARDS

This section gives the details of the contents of the core units of competency
required in Gas Metal Arc Welding (GMAW) NC III.

BASIC COMPETENCIES

UNIT OF COMPETENCY : LEAD WORKPLACE COMMUNICATION

UNIT CODE : 500311109

UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required to lead in the dissemination and discussion of
ideas, information and issues in the workplace.

ELEMENT PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Communicate 1.1. Appropriate communication method is selected
information about 1.2. Multiple operations involving several topics areas are
workplace
processes communicated accordingly
1.3. Questions are used to gain extra information
1.4. Correct sources of information are identified
1.5. Information is selected and organized correctly
1.6. Verbal and written reporting is undertaken when
required
1.7. Communication skills are maintained in all situations
2. Lead workplace 2.1. Response to workplace issues are sought
discussions 2.2. Response to workplace issues are provided
immediately
2.3. Constructive contributions are made to workplace
discussions on such issues as production, quality and
safety
2.4. Goals/objectives and action plan undertaken in the
workplace are communicated
3. Identify and 3.1. Issues and problems are identified as they arise
communicate issues 3.2. Information regarding problems and issues are
arising in the organized coherently to ensure clear and effective
workplace communication
3.3. Dialogue is initiated with appropriate personnel
3.4. Communication problems and issues are raised as
they arise
Weldncii11-3 3
RANGE OF VARIABLES
VARIABLE RANGE
1. Methods of 1.1. Non-verbal gestures
communication
1.2. Verbal
1.3. Face to face
1.4. Two-way radio
1.5. Speaking to groups
1.6. Using telephone
1.7. Written
1.8. Internet

Weldncii11-3 4
RANGE OF VARIABLES
VARIABLE RANGE
1. Methods of 1.1. Non-verbal gestures
communication
1.2. Verbal
1.3. Face to face
1.4. Two-way radio
1.5. Speaking to groups
1.6. Using telephone
1.7. Written
1.8. Internet

Weldncii11-3 4
 UNIT OF COMPETENCY : LEAD SMALL TEAMS

UNIT CODE : 500311110

UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes to
lead small teams including setting and maintaining
team and individual performance standards.

ELEMENT PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Provide team 1.1. Work requirements are identified and presented to team
leadership members
1.2. Reasons for instructions and requirements are
communicated to team members
1.3. Team members’ queries and concerns are recognized,
discussed and dealt with
2. Assign 2.1. Duties, and responsibilities are allocated having regard
responsibilities to the skills, knowledge and aptitude required to properly
undertake the assigned task and according to company
policy
2.2. Duties are allocated having regard to individual
preference, domestic and personal considerations,
whenever possible
3. Set performance 3.1. Performance expectations are established based on
expectations for client needs and according to assignment requirements
team members 3.2. Performance expectations are based on individual team
members duties and area of responsibility
3.3. Performance expectations are discussed and
disseminated to individual team members
4. Supervised team 4.1. Monitoring of performance takes place against defined
performance performance criteria and/or assignment instructions and
corrective action taken if required
4.2. Team members are provided with feedback, positive
support and advice on strategies to overcome any
deficiencies
4.3. Performance issues which cannot be rectified or
addressed within the team are referenced to appropriate
personnel according to employer policy
4.4. Team members are kept informed of any changes in the
priority allocated to assignments or tasks which might
impact on client/customer needs and satisfaction
4.5. Team operations are monitored to ensure that
employer/client needs and requirements are met
4.6. Follow-up communication is provided on all issues
affecting the team
4.7. All relevant documentation is completed in accordance
with company procedures

Weldncii11-3 6
RANGE OF VARIABLES
VARIABLE RANGE

1. Work requirements 1.1. Client Profile

1.2. Assignment instructions

2. Team member’s 2.1. Roster/shift details

concerns

3. Monitor 3.1. Formal process

performance
3.2. Informal process

4. Feedback 4.1. Formal process

4.2. Informal process

5. Performance issues 5.1. Work output

5.2. Work quality

5.3. Team participation

5.4. Compliance with workplace protocols

5.5. Safety

5.6. Customer service

Weldncii11-3 7
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate:
competency 1.1. Maintained or improved individuals and/or team
performance given a variety of possible scenario
1.2. Assessed and monitored team and individual
performance against set criteria
1.3. Represented concerns of a team and individual to
next level of management or appropriate specialist
and to negotiate on their behalf
1.4. Allocated duties and responsibilities, having regard to
individual’s knowledge, skills and aptitude and the
needs of the tasks to be performed
1.5. Set and communicated performance expectations for
a range of tasks and duties within the team and
provided feedback to team members
2. Underpinning 2.1. Company policies and procedures
knowledge 2.2. Relevant legal requirements
2.3. How performance expectations are set
2.4. Methods of Monitoring Performance
2.5. Client expectations
2.6. Team member’s duties and responsibilities
3. Underpinning skills 3.1. Communication skills required for leading teams
3.2. Informal performance counseling skills
3.3. Team building skills
3.4. Negotiating skills
4. Resource The following resources MUST be provided:
implications 4.1. Access to relevant workplace or appropriately
simulated environment where assessment can take
place
4.2. Materials relevant to the proposed activity or task
5. Methods of Competency may be assessed through:
assessment 5.1. Direct observations of work activities of the individual
member in relation to the work activities of the group
5.2. Observation of simulation and/or role play involving
the participation of individual member to the
attainment of organizational goal
5.3. Case studies and scenarios as a basis for discussion
of issues and strategies in teamwork
6. Context for 6.1. Competency assessment may occur in workplace or
assessment any appropriately simulated environment
6.2. Assessment shall be observed while task are being
undertaken whether individually or in-group

Weldncii11-3 8
RANGE OF VARIABLES
VARIABLE RANGE

1. Work requirements 1.1. Client Profile

1.2. Assignment instructions

2. Team member’s 2.1. Roster/shift details

concerns

3. Monitor 3.1. Formal process

performance
3.2. Informal process

4. Feedback 4.1. Formal process

4.2. Informal process

5. Performance issues 5.1. Work output

5.2. Work quality

5.3. Team participation

5.4. Compliance with workplace protocols

5.5. Safety

5.6. Customer service

Weldncii11-3 7
RANGE OF VARIABLES
VARIABLE RANGE
1. Preparing for 1.1 Background information on other parties to the
negotiation negotiation
1.2 Good understanding of topic to be negotiated
1.3 Clear understanding of desired outcome/s
1.4 Personal attributes
1.4.1 self awareness
1.4.2 self esteem
1.4.3 objectivity
1.4.4 empathy
1.4.5 respect for others
1.5 Interpersonal skills
1.5.1 listening/reflecting
1.5.2 non verbal communication
1.5.3 assertiveness
1.5.4 behavior labeling
1.5.5 testing understanding
1.5.6 seeking information
1.5.7 self disclosing
1.6 Analytic skills
1.6.1 observing differences between content and
process
1.6.2 identifying bargaining information
1.6.3 applying strategies to manage process
1.6.4 applying steps in negotiating process
1.6.5 strategies to manage conflict
1.6.6 steps in negotiating process
1.6.7 options within organization and externally for
resolving conflict

2. Non verbal 2.1 Friendly reception

environments 2.2 Warm and welcoming room
2.3 Refreshments offered
2.4 Lead in conversation before negotiation begins
3. Active listening 3.1 Attentive
3.2 Don’t interrupt
3.3 Good posture
3.4 Maintain eye contact
3.5 Reflective listening

4. Questioning 4.1 Direct

techniques 4.2 Indirect
4.3 Open-ended

Weldncii11-3 10
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate:
competency 1.1 Demonstrated sufficient knowledge of the factors
influencing negotiation to achieve agreed outcome
1.2 Participated in negotiation with at least one person to
achieve an agreed outcome

2. Underpinning 2.1 Codes of practice and guidelines for the organization

knowledge and 2.2 Organizations policy and procedures for negotiations
attitude 2.3 Decision making and conflict resolution strategies
procedures
2.4 Problem solving strategies on how to deal with
unexpected questions and attitudes during negotiation
2.5 Flexibility
2.6 Empathy

3. Underpinning skills 3.1 Interpersonal skills to develop rapport with other parties
3.2 Communication skills (verbal and listening)
3.3 Observation skills
3.4 Negotiation skills

4. Resource The following resources MUST be provided:

implications 4.1 Room with facilities necessary for the negotiation
process
4.2 Human resources (negotiators)

5. Methods of Competency may be assessed through:

assessment 5.1 Observation/demonstration and questioning
5.2 Portfolio assessment
5.3 Oral and written questioning
5.4 Third party report

6. Context for 6.1 Competency to be assessed in real work environment or

assessment in a simulated workplace setting.

Weldncii11-3 11
UNIT OF COMPETENCY : SOLVE PROBLEMS RELATED TO WORK
ACTIVITIES
UNIT CODE : 500311112
UNIT DESCRIPTOR : This unit of covers the knowledge, skills and attitudes
required to solve problems in the workplace including
the application of problem solving techniques and to
determine and resolve the root cause of problems.

ELEMENT PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Identify the problem 1.1. Variances are identified from normal operating
parameters; and product quality
1.2. Extent, cause and nature are of the problem are
defined through observation, investigation and
analytical techniques
1.3. Problems are clearly stated and specified
2. Determine 2.1. Possible causes are identified based on experience
fundamental and the use of problem solving tools / analytical
causes of the techniques.
problem
2.2. Possible cause statements are developed based on
findings
2.3. Fundamental causes are identified per results of
investigation conducted
3. Determine 3.1. All possible options are considered for resolution of
corrective action the problem
3.2. Strengths and weaknesses of possible options are
considered
3.3. Corrective actions are determined to resolve the
problem and possible future causes
3.4. Action plans are developed identifying measurable
objectives, resource needs and timelines in
accordance with safety and operating procedures
4. Provide 4.1. Report on recommendations are prepared
recommendation/s
to manager 4.2. Recommendations are presented to appropriate
personnel.
4.3. Recommendations are followed-up, if required

Weldncii11-3 12
RANGE OF VARIABLES
VARIABLE RANGE
1. Preparing for 1.1 Background information on other parties to the
negotiation negotiation
1.2 Good understanding of topic to be negotiated
1.3 Clear understanding of desired outcome/s
1.4 Personal attributes
1.4.1 self awareness
1.4.2 self esteem
1.4.3 objectivity
1.4.4 empathy
1.4.5 respect for others
1.5 Interpersonal skills
1.5.1 listening/reflecting
1.5.2 non verbal communication
1.5.3 assertiveness
1.5.4 behavior labeling
1.5.5 testing understanding
1.5.6 seeking information
1.5.7 self disclosing
1.6 Analytic skills
1.6.1 observing differences between content and
process
1.6.2 identifying bargaining information
1.6.3 applying strategies to manage process
1.6.4 applying steps in negotiating process
1.6.5 strategies to manage conflict
1.6.6 steps in negotiating process
1.6.7 options within organization and externally for
resolving conflict

2. Non verbal 2.1 Friendly reception

environments 2.2 Warm and welcoming room
2.3 Refreshments offered
2.4 Lead in conversation before negotiation begins
3. Active listening 3.1 Attentive
3.2 Don’t interrupt
3.3 Good posture
3.4 Maintain eye contact
3.5 Reflective listening

4. Questioning 4.1 Direct

techniques 4.2 Indirect
4.3 Open-ended

Weldncii11-3 10
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate:
competency 1.1. Identified the problem
1.2. Determined the fundamental causes of the problem
1.3. Determined the correct / preventive action
1.4. Provided recommendation to manager
These aspects may be best assessed using a range of
scenarios / case studies / what ifs as a stimulus with a walk
through forming part of the response. These assessment
activities should include a range of problems, including
new, unusual and improbable situations that may have
happened.
2. Underpinning 2.1. Competence includes a thorough knowledge and
knowledge understanding of the process, normal operating
parameters, and product quality to recognize non-
standard situations
2.2. Competence to include the ability to apply and
explain, sufficient for the identification of fundamental
cause, determining the corrective action and
provision of recommendations
2.2.1. Relevant equipment and operational
processes
2.2.2.Enterprise goals, targets and measures
2.2.3. Enterprise quality, OHS and environmental
requirement
2.2.4. Principles of decision making strategies and
techniques
2.2.5. Enterprise information systems and data
collation
2.2.6.Industry codes and standards
3. Underpinning skills 3.1. Using range of formal problem solving techniques
3.2. Identifying and clarifying the nature of the problem
3.3. Devising the best solution
3.4. Evaluating the solution
3.5. Implementation of a developed plan to rectify the
problem

Weldncii11-3 14
4. Resource 4.1. Assessment will require access to an operating plant
implications over an extended period of time, or a suitable
method of gathering evidence of operating ability
over a range of situations. A bank of scenarios / case
studies / what ifs will be required as well as bank of
questions which will be used to probe the reason
behind the observable action.
5. Methods of Competency may be assessed through:
assessment
5.1. Case studies on solving problems in the workplace
5.2. Observation
The unit will be assessed in a holistic manner as is practical
and may be integrated with the assessment of other
relevant units of competency. Assessment will occur over a
range of situations, which will include disruptions to normal,
smooth operation. Simulation may be required to allow for
timely assessment of parts of this unit of competency.
Simulation should be based on the actual workplace and
will include walk through of the relevant competency
components.
6. Context for 6.1. In all workplace, it may be appropriate to assess this
assessment unit concurrently with relevant teamwork or operation
units.

Weldncii11-3 15
UNIT OF COMPETENCY : USE MATHEMATICAL CONCEPTS AND
TECHNIQUES

UNIT CODE : 3500311113

UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required in the application of mathematical
concepts and techniques.

Performance Criteria
ELEMENT Italicized terms are elaborated in the Range of Variables
1. Identify 1.1 Problem areas are identified based on given condition
mathematical tools 1.2 Mathematical techniques are selected based on the
and techniques to given problem
solve problem
2. Apply mathematical 2.1 Mathematical techniques are applied based on the
procedure/solution problem identified
2.2 Mathematical computations are performed to the level
of accuracy required for the problem
2.3 Results of mathematical computation is determined and
verified based on job requirements

3. Analyze results 3.1 Result of application is reviewed based on expected

and required specifications and outcome
3.2 Appropriate action is applied in case of error

Weldncii11-3 16
RANGE OF VARIABLES
VARIABLE RANGE

1. Analytical 1.1. Brainstorming

techniques
1.2. Intuitions/Logic
1.3. Cause and effect diagrams
1.4. Pareto analysis
1.5. SWOT analysis
1.6. Gant chart, Pert CPM and graphs
1.7. Scatter grams
2. Problem 2.1. Non – routine process and quality problems
2.2. Equipment selection, availability and failure
2.3. Teamwork and work allocation problem
2.4. Safety and emergency situations and incidents
3. Action plans 3.1. Priority requirements
3.2. Measurable objectives
3.3. Resource requirements
3.4. Timelines
3.5. Co-ordination and feedback requirements
3.6. Safety requirements
3.7. Risk assessment
3.8. Environmental requirements

Weldncii11-3 13
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate:
competency 1.1 Identified, applied and reviewed the use of
mathematical concepts and techniques to workplace
problems

2. Underpinning 2.1 Fundamental operation (addition, subtraction, division,

knowledge multiplication)
2.2 Measurement system
2.3 Precision and accuracy
2.4 Basic measuring tools/devices

3. Underpinning skills 3.1 Applying mathematical computations

3.2 Using calculator
3.3 Using different measuring tools

4. Resource The following resources MUST be provided:

implications 4.1 Calculator
4.2 Basic measuring tools
4.3 Case Problems

5. Methods of Competency may be assessed through:

assessment 5.1 Authenticated portfolio
5.2 Written Test
5.3 Interview/Oral Questioning
5.4 Demonstration
6. Context for 6.1 Competency may be assessed in the work place or in a
assessment simulated work place setting

Weldncii11-3 18
UNIT OF COMPETENCY : USE RELEVANT TECHNOLOGIES

UNIT CODE : 500311114

UNIT DESCRIPTOR : This unit of competency covers the knowledge,

skills, and attitude required in selecting, sourcing
and applying appropriate and affordable
technologies in the workplace.

PERFORMANCE CRITERIA
ELEMENT Italicized terms are elaborated in the Range of Variables

1. Study/select 1.1 Usage of different technologies is determined based on

appropriate job requirements
technology 1.2 Appropriate technology is selected as per work
specification

2. Apply relevant 2.1 Relevant technology is effectively used in carrying

technology out function
2.2 Applicable software and hardware are used as per
task requirement
2.3 Management concepts are observed and practiced as
per established industry practices

3. Maintain/enhance of 3.1 Maintenance of technology is applied in accordance with

relevant technology the industry standard operating procedure,
manufacturer’s operating guidelines and
occupational health and safety procedure to ensure
its operative ability
3.2 Updating of technology is maintained through continuing
education or training in accordance with job requirement
3.3 Technology failure/ defect is immediately reported to the
concern/responsible person or section for appropriate
action

Weldncii11-3 19
RANGE OF VARIABLES
VARIABLE RANGE
1. Technology May include but are not limited to:
1.1 Office technology
1.2 Industrial technology
1.3 System technology
1.4 Information technology
1.5 Training technology

2. Management May include but not limited to:

concepts 2.1 Real Time Management
2.2 KAIZEN or continuous improvement
2.3 5s
2.4 Total Quality Management
2.5 Other management/productivity tools

3. Industry standard 3.1 Written guidelines relative to the usage of office

operating procedure technology/equipment
3.2 Verbal advise/instruction from the co-worker

4. Manufacturer’s 4.1 Written instruction/manuals of specific technology/

operating guidelines/ equipment
instructions 4.2 General instruction manual
4.3 Verbal advise from manufacturer relative to the
operation of equipment

5. Occupational health 5.1 Relevant statutes on OHS

and safety 5.2 Company guidelines in using
procedure technology/equipment

6. Appropriate action 6.1 Implementing preventive maintenance schedule

6.2 Coordinating with manufacturer’s technician

Weldncii11-3 20
UNIT OF COMPETENCY : USE MATHEMATICAL CONCEPTS AND
TECHNIQUES

UNIT CODE : 3500311113

UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required in the application of mathematical
concepts and techniques.

Performance Criteria
ELEMENT Italicized terms are elaborated in the Range of Variables
1. Identify 1.1 Problem areas are identified based on given condition
mathematical tools 1.2 Mathematical techniques are selected based on the
and techniques to given problem
solve problem
2. Apply mathematical 2.1 Mathematical techniques are applied based on the
procedure/solution problem identified
2.2 Mathematical computations are performed to the level
of accuracy required for the problem
2.3 Results of mathematical computation is determined and
verified based on job requirements

3. Analyze results 3.1 Result of application is reviewed based on expected

and required specifications and outcome
3.2 Appropriate action is applied in case of error

Weldncii11-3 16
 COMMON COMPETENCIES

UNIT OF COMPETENCY : APPLY SAFETY PRACTICES

UNIT CODE : MEE721201

UNIT DESCRIPTOR : This unit covers the competencies required to apply

safety practices in the workplace.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Identify hazardous area 1.1 Hazards are identified correctly in accordance
with OHS principles.
1.2 Safety signs and symbols are identified and
adhered to.

2. Use protective clothing 2.1 Appropriate protective clothing and devices

and devices correctly selected and used in accordance with
OHS requirements or industry/company policy

3. Perform safe handling of 3.1 Safety procedures for pre-use check and
tools, equipment and operation of tools and equipment followed in
materials accordance with industry/ company policies.
3.2 Tools, equipment and materials handled safely in
accordance with OHS requirements and industry/
company policies.

4. Perform first aid 4.1 First aid treatment of injuries are carried out
according to recommended procedures

5. Use fire extinguisher 5.1 Fire extinguisher selected and operated correctly
according to the type of fire.

Weldncii11-3 22
RANGE OF VARIABLES
VARIABLE RANGE
1. Hazards 1.1 Cluttered tools and materials
1.2 Slippery floors (caused by oil, grease or any liquid)
1.3 Exposed electrical wires
1.4 Sharp edges
1.5 Machine without guards or with exposed moving parts

2. Protective clothing and Protective clothing and devices may include but is not
devices limited to:
2.1 safety glasses/goggles
2.2 safety shoes
2.3 overalls
2.4 cap
2.5 gloves

3. Injuries Injuries may include:

3.1 burns/scalds
3.2 fractures
3.3 cuts and abrasions
3.4 poisoning
3.5 foreign bodies in the eye
3.6 concussion
3.7 shock

4. Type of fires Fires involving or caused by:

4.1 common combustibles (wood, cloth, paper, rubber
and plastic)
4.2 flammable liquids (gasoline, oil, solvents, paints, etc.)
4.3 energized electrical equipment (wiring, fuse boxes,
circuit breakers, appliances, etc.
4.4 combustible metals (magnesium, sodium, etc.)

Weldncii11-3 23
EVIDENCE GUIDE
1. Critical aspects Assessment requires evidence that the candidate:
of competency 1.1 identified hazardous area
1.2 used protective clothing and devices
1.3 handled tools, equipment and materials properly
1.4 performed first aid
1.5 used fire extinguisher

2. Underpinning 2.1 Shop safety signs, symbols and alarms

knowledge and 2.2 Safety precautionary measures
attitude 2.3 Housekeeping
2.4 Machine tools
2.5 First aid
2.6 Engineering materials
2.7 Fire extinguishers

3. Underpinning 3.1 Operating machine tools

skills 3.2 Handling tools and materials
3.3 Communicating with superiors and co-workers
3.4 Interpreting instructions

4. Resource The following resources must be provided

implications 4.1 Tools, equipment and facilities appropriate to processes or
activity
4.2 Materials relevant to the proposed activity

5. Method of Competency must be assessed through:

assessment 5.1 Demonstration
5.2 Written or oral short answer questions
5.3 Practical exercises

6. Context for  Competency may be assessed in the workplace or in

assessment simulated workplace environment.

Weldncii11-3 24
UNIT OF COMPETENCY : USE RELEVANT TECHNOLOGIES

UNIT CODE : 500311114

UNIT DESCRIPTOR : This unit of competency covers the knowledge,

skills, and attitude required in selecting, sourcing
and applying appropriate and affordable
technologies in the workplace.

PERFORMANCE CRITERIA
ELEMENT Italicized terms are elaborated in the Range of Variables

1. Study/select 1.1 Usage of different technologies is determined based on

appropriate job requirements
technology 1.2 Appropriate technology is selected as per work
specification

2. Apply relevant 2.1 Relevant technology is effectively used in carrying

technology out function
2.2 Applicable software and hardware are used as per
task requirement
2.3 Management concepts are observed and practiced as
per established industry practices

3. Maintain/enhance of 3.1 Maintenance of technology is applied in accordance with

relevant technology the industry standard operating procedure,
manufacturer’s operating guidelines and
occupational health and safety procedure to ensure
its operative ability
3.2 Updating of technology is maintained through continuing
education or training in accordance with job requirement
3.3 Technology failure/ defect is immediately reported to the
concern/responsible person or section for appropriate
action

Weldncii11-3 19
RANGE OF VARIABLES
VARIABLE RANGE
1. Drawing Drawing technique include
1.1 Perspective
1.2 Exploded view
1.3 Hidden view technique

Projections
1.4 First angle projections
1.5 Third angle projections

2. Tolerance 2.1 General tolerance

2.2 Angular tolerance
2.3 Geometric tolerance

Weldncii11-3 26
EVIDENCE GUIDE
1. Critical aspects Assessment requires evidence that the candidate interpreted
of competency technical drawings and sketches.

2. Underpinning 2.1 Alphabet of lines

knowledge 2.2 Projections
2.3 Drawing symbols
2.4 Dimensioning techniques
2.5 Tolerances

3. Underpinning 3.1 Communication skills (reading and comprehension)

skills 3.2 Computation skills

4. Resource The following resources must be provided

implications 4.1 Working drawing or plans or sketches
4.2 Measuring tools
4.3 Drawings, sketches or blueprint
4.4 Specimen parts/components

5. Method of Competency must be assessed through:

assessment 5.1 direct observation
5.2 written or oral short answer questions
5.3 demonstration
5.4 project/work sample
5.5 portfolio

6. Context for  Competency may be assessed in the workplace or in

assessment simulated workplace environment.

Weldncii11-3 27
UNIT OF COMPETENCY : PERFORM INDUSTRY CALCULATIONS

UNIT CODE : MEE721203

UNIT DESCRIPTOR : This unit covers the competencies required to perform

basic calculations using the four fundamental
operation.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Perform four 1.1 Simple calculations involving whole numbers,
fundamental operations. mixed numbers, fraction and decimal are
performed using four fundamental operations.

2. Perform conversion of 2.1 Units are converted to the required figure using
units the given formulae
2.2 English measurements are converted to metric
measurements according to procedure.

3. Perform calculations on 3.1 Simple calculations are performed on algebraic

algebraic expressions expressions using four fundamental operations.
3.2 Simple transposition of formulae are carried out to
isolate the variable required, involving the four
fundamental operations.
3.3 Where appropriate, formulae are constructed to
enable problems to be solved.
3.4 Equations involving on unknown solved correctly.

4. Compute percentage 4.1 Percentages are computed using appropriate

and ratio formula.
Ratio and proportion are computed using
appropriate formula.

Weldncii11-3 28
 COMMON COMPETENCIES

UNIT OF COMPETENCY : APPLY SAFETY PRACTICES

UNIT CODE : MEE721201

UNIT DESCRIPTOR : This unit covers the competencies required to apply

safety practices in the workplace.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Identify hazardous area 1.1 Hazards are identified correctly in accordance
with OHS principles.
1.2 Safety signs and symbols are identified and
adhered to.

2. Use protective clothing 2.1 Appropriate protective clothing and devices

and devices correctly selected and used in accordance with
OHS requirements or industry/company policy

3. Perform safe handling of 3.1 Safety procedures for pre-use check and
tools, equipment and operation of tools and equipment followed in
materials accordance with industry/ company policies.
3.2 Tools, equipment and materials handled safely in
accordance with OHS requirements and industry/
company policies.

4. Perform first aid 4.1 First aid treatment of injuries are carried out
according to recommended procedures

5. Use fire extinguisher 5.1 Fire extinguisher selected and operated correctly
according to the type of fire.

Weldncii11-3 22
EVIDENCE GUIDE
1. Critical aspects Assessment requires evidence that the candidate performed
of competency calculations:
1.1 using four fundamental operations
1.2 involving fractions and mixed numbers
1.3 involving fractions and decimals
1.4 on algebraic expressions
1.5 involving ratio and proportion

2. Underpinning 2.1 English and metric system of measurements

knowledge and 2.2 Four fundamental operations
attitude 2.3 Method of transposing formulae
2.4 Equation formulation

3. Underpinning 3.1 Performing calculations using pen and paper or with the use
skills of calculator

4. Resource The following resources must be provided

implications 4.1 Tools and facilities appropriate to processes or activity
4.2 Materials relevant to the proposed activity

5. Method of Competency must be assessed through:

assessment 5.1 written or oral short answer questions
5.2 practical exercises

6. Context for Competency may be assessed in the workplace or in simulated

assessment workplace environment.

Weldncii11-3 30
UNIT OF COMPETENCY : CONTRIBUTE TO QUALITY SYSTEM

UNIT CODE : MEE721204

UNIT DESCRIPTOR : This unit involves competence required to inspect work

against specification and standards and apply quality
standards to work.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Inspect work done 1.1 Appropriate inspections are conducted to ensure
company quality systems and procedures are
maintained/ followed.
1.2 Job specifications/work order and quality
standards are identified.
1.3 Faults/Defects are identified and rectified
according to company procedures.

2. Apply quality standards 2.1 Inspections are conducted throughout the

to work manufacturing processes to ensure quality
standards are maintained.
2.2 Appropriate quality standards are applied
throughout the production/fabrication process.
2.3 All activities are coordinated throughout the
workplace to ensure efficient quality work
2.4 outcomes.
Records of work quality are maintained according
to the company requirements.

3 Protect company 3.1 Possible damage to company property is

property and customer avoided by adherence to company quality
interests 3.2 procedures.
Quality of work is reviewed to ensure customer
requirements and company standards are met.

Weldncii11-3 31
RANGE OF VARIABLES
VARIABLE RANGE
1. Quality system and Quality system and procedures may be contained in:
procedures 1.1 work instructions
1.2 safe work procedures
1.3 product specifications
1.4 equipment maintenance schedules
1.5 technical procedures adopted or specifically
prepared standards
1.6 company/industry rules

2. Company property Company properties includes :

2.1 production and/or fabrication equipment
2.2 hand and power tools
2.3 OH&S paraphernalia
2.4 facilities

Weldncii11-3 32
UNIT OF COMPETENCY : INTERPRET DRAWINGS AND SKETCHES

UNIT CODE : MEE721202

UNIT DESCRIPTOR : This unit covers the competencies required to read and
interpret drawings and sketches.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Identify standard 1.1 Alphabet of lines are identified
alphabet of lines 1.2 Uses of the alphabet of lines are explained

2. Identify orthographic/ 2.1 Orthographic and isometric drawing are identified

isometric views 2.2 Orthographic and isometric views are explained

3. Interpret standard 3.1 Drawing symbols are interpreted according to

drawing symbols, drawing standards
dimensional tolerances 3.2 Dimensional tolerances, notations are interpreted
and notations according to specifications

Weldncii11-3 25
UNIT OF COMPETENCY : USE HAND TOOLS

UNIT CODE : MEE721205

UNIT DESCRIPTOR : This unit covers the competencies required to use hand
tools.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Select hand tools 1.1 Hand tools selected are appropriate to the
requirements of the task.
1.2 Unsafe or defective tools are identified and
marked for repair according to procedure.

2. Use hand tools 2.1 Hand tools are used to produce the desired
outcomes to job specifications.
2.2 Task performed in accordance with company or
industry safety procedure.

3. Maintain hand tools 3.1 Routine maintenance of hand tools is

undertaken according to standard operating
procedures, principles and techniques.
3.2 Hand tools are stored in designated location in
accordance with manufacturer’s
instruction/standard operating procedure.

Weldncii11-3 34
RANGE OF VARIABLES
VARIABLE RANGE
1. Hand tools Hand tools includes but not limited to:
1.1 Hacksaws
1.2 Hammers (ball peen, chipping)
1.3 Punches
1.4 Screwdrivers
1.5 Wrenches
1.6 Scrapers
1.7 Chisels
1.8 Gouges
1.9 Files
1.10 Clamps

2. Task Tasks may include:

2.1 Adjusting
2.2 Dismantling
2.3 Assembling
2.4 Finishing of item or components

3. Routine maintenance Routine maintenance may include:

3.1 Cleaning
3.2 Lubricating
3.3 Tightening
3.4 Simple tool repair
3.5 Hand sharpening

Weldncii11-3 35
EVIDENCE GUIDE
1. Critical aspects Assessment requires evidence that the candidate:
of competency 1.1 Selected and used hand tools appropriate to the job
1.2 Performed routine maintenance and storage of hand tools

2. Underpinning 2.1 Types and uses of hand tools

knowledge and 2.2 Hand tool defects
attitude 2.3 Procedure, principles and techniques in maintenance of
hand tools

3. Underpinning 3.1 Handling tools and materials

skills 3.2 Communicating with superiors and co-workers
3.3 Interpreting instructions

4. Resource The following resources must be provided

implications 4.1 Tools, equipment and facilities appropriate to the process
or activity
4.2 Materials relevant to the proposed activity

5. Method of Competency must be assessed through:

assessment 5.1 Demonstration
5.2 Written or oral short answer questions
5.3 Practical exercises

6. Context for Competency may be assessed in the workplace or in simulated

assessment workplace environment.

Weldncii11-3 36
UNIT OF COMPETENCY : PERFORM INDUSTRY CALCULATIONS

UNIT CODE : MEE721203

UNIT DESCRIPTOR : This unit covers the competencies required to perform

basic calculations using the four fundamental
operation.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Perform four 1.1 Simple calculations involving whole numbers,
fundamental operations. mixed numbers, fraction and decimal are
performed using four fundamental operations.

2. Perform conversion of 2.1 Units are converted to the required figure using
units the given formulae
2.2 English measurements are converted to metric
measurements according to procedure.

3. Perform calculations on 3.1 Simple calculations are performed on algebraic

algebraic expressions expressions using four fundamental operations.
3.2 Simple transposition of formulae are carried out to
isolate the variable required, involving the four
fundamental operations.
3.3 Where appropriate, formulae are constructed to
enable problems to be solved.
3.4 Equations involving on unknown solved correctly.

4. Compute percentage 4.1 Percentages are computed using appropriate

and ratio formula.
Ratio and proportion are computed using
appropriate formula.

Weldncii11-3 28
RANGE OF VARIABLE
VARIABLE RANGE
1. Materials and 1.1 Mild steel
consumables 1.2 Carbon steel
1.3 Alloy steel (level III & IV)
1.4 Cutting gases
1.5 Gouging electrodes
1.6 Grinding/cutting discs
1.7 Run on/run off, backing plates/ring
1.8 Cutting accessories

2. Cut Cut material using

2.1 Oxy-acetylene gas cutting equipment (manual and /or
automatic)
2.2 Plasma cutting equipment
2.3 Shearing machine
2.4 Disc cutter

3. Specification Specifications based on

3.1 Welding codes
3.2 Reference Industry standards
3.3 Client specification

4. Cleaned Surfaces and edges are cleaned by

4.1 Grinding or sanding
4.2 Filing
4.3 Chemical washing (Degreaser)

5. Safety procedures 5.1 Wearing of required PPE

5.2 Securing oxy-acetylene tanks before, during and after
use
5.3 Checking oxy-acetylene hose for gas leaks
5.4 Switch off equipment after use
5.5 Checking electrical equipment and devices

Weldncii11-3 38
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate:
competency 1.1 Perform edge preparation in accordance with
WPS and safety procedures
1.2 Use edge preparation equipment and tools in
accordance with the requirements or
manufacturer’s instructions

2. Underpinning knowledge 2.1 Interpretation of plans and drawings

2.2 Selection of appropriate method of edge
preparation
2.3 Selection of appropriate cutting equipment,
accessories and supplies
2.4 Operation of cutting equipment such as
mechanical, gas and plasma
2.5 Operation of grinding equipment
2.6 Safety procedures for cutting and grinding

3. Underpinning skills 3.1 Measuring and communication skills

3.2 Set up of cutting equipment such as mechanical,
gas and plasma
3.3 Cutting techniques
3.4 Grinding techniques
3.5 Observance of safety procedures

4. Resource implications The following resources must be provided:

4.1 Relevant documentation such as WPS and
working drawing
4.2 Supplies and materials
4.3 Cutting equipment and facilities
4.4 Grinding equipment and facilities
4.5 Measuring tools
4.6 PPE
4.7 Stand-by fire fighting equipment

5. Method of assessment Competency must be assessed through:

5.1 Observation/evaluation
5.2 Oral questioning
5.3 Inspection of prepared edges

6. Context of assessment Competency to be assessed while a task is being

undertaken in the workplace or in a simulated
workplace setting.

Weldncii11-3 39
UNIT TITLE : SET UP WELDING EQUIPMENT

UNIT CODE : MEE721207

DESCRIPTOR : This unit covers the skills, knowledge and attitudes in

preparing equipment for welding.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1.1 Set up welding 1.1 Requirements for welding is determined from job
machine requirements, welding procedures and specifications
and/or technical drawings.
1.2 Welding machine is set up in accordance with job
requirements, welding procedures and specifications,
technical drawings and manufacturer’s instructions.
1.3 Welding machine should be connected to an
independent power supply and wired up or set to the
polarity indicated in the welding procedures
/specifications or as recommended by the
manufacturer.
1.4 Current, voltage, and wire feed settings is fine-tuned or
adjusted consistent with job requirements to produce
acceptable weld.
1.5 Task is completed without causing damage to the tools,
equipment and materials and injury to self and others.

2. Set up welding 2.1 Welding machine accessories and consumables are

accessories identified from job requirements, welding procedures
and specifications.
2.2 Welding machine accessories and consumables are set
up in accordance with job requirements, welding
procedures and specifications and/or manufacturer’s
instructions.
2.3 Spools firmly locked to holder, rollers adjusted to
correct tension.
2.4 Purging hoses, damps, flow meter, regulators, torches
and guns are properly installed where needed.
2.5 Gas tanks properly secured where needed.

3. Set up welding 3.1 Braces, stiffeners, rails and other jigs are provided and
positioners, jigs and in conformity with job requirements.
fixtures 3.2 Work items/materials are protected from strong winds,
drafts and rainfall

4. Set up pre-heating 4.1 Pre-heating equipment appropriate to the job

tools/equipment as requirement and specifications
required 4.2 Equipment operated in conformance with the
manufacturer’s instructions.

Weldncii11-3 40
UNIT OF COMPETENCY : CONTRIBUTE TO QUALITY SYSTEM

UNIT CODE : MEE721204

UNIT DESCRIPTOR : This unit involves competence required to inspect work

against specification and standards and apply quality
standards to work.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Inspect work done 1.1 Appropriate inspections are conducted to ensure
company quality systems and procedures are
maintained/ followed.
1.2 Job specifications/work order and quality
standards are identified.
1.3 Faults/Defects are identified and rectified
according to company procedures.

2. Apply quality standards 2.1 Inspections are conducted throughout the

to work manufacturing processes to ensure quality
standards are maintained.
2.2 Appropriate quality standards are applied
throughout the production/fabrication process.
2.3 All activities are coordinated throughout the
workplace to ensure efficient quality work
2.4 outcomes.
Records of work quality are maintained according
to the company requirements.

3 Protect company 3.1 Possible damage to company property is

property and customer avoided by adherence to company quality
interests 3.2 procedures.
Quality of work is reviewed to ensure customer
requirements and company standards are met.

Weldncii11-3 31
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate
competency 1.1 Set up and install welding machine,
accessories,
welding positioners, jigs and fixtures and pre-
heating equipment within allotted time and in
accordance with OH&S rules and accessible
and convenient location.
1.2 Applied housekeeping and 5S practices

2. Underpinning knowledge 2.1 Types and uses of welding equipment and

accessories
2.2 Power requirement and capacity of welding
machine and its accessories
2.3 Operating capacity of welding machine and
accessories
2.4 Basic electricity
2.5 Shop safety, housekeeping and 5S procedures

3. Underpinning skills 3.1 Setting and operating welding machine and

accessories
3.2 Communication skills
3.3 Recognizing operational abnormalities and
faults in welding machine and accessories
3.4 Fine tuning of welding machine and accessories
for optimum operation
3.5 Minor repairs/maintenance of welding machine
and accessories
3.6 Use of PPE

4. Resource implications The following resources must be provided:

4.1 Appropriately ventilated work area/shop with
welding facilities, machines and accessories
4.2 PPE

5. Method of assessment Competency must be assessed through:

5.1 Observation/evaluation
5.2 Oral questioning

6. Context of assessment Competency to be assessed while a task is being

undertaken in the workplace or in a simulated
workplace setting.

Weldncii11-3 42
UNIT TITLE : FIT UP WELD MATERIALS

UNIT CODE : MEE721208

DESCRIPTOR : This unit covers the skills, knowledge and attitudes in fitting
up welding materials.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Perform tack welding 1.1 Tack welding is performed in accordance with the
requirements of WPS and client’s specifications.
1.2 Tack welding is performed visually and dimensionally
acceptable.
1.3 Backing plate, stiffener, running plate installed as
required.
1.4 Joints are free from rust, paints, grease and other
foreign materials prior to fit up or tacking.

2. Check gap and 2.1 Root gap is performed in accordance with the
alignment requirements of WPS.
2.2 Alignment within the range of acceptability of code and
standard.
2.3 Fitted materials visually free from stresses

3. Set up welding 3.1 Weld specimen positioned and secured according to the
positioner requirements.

Weldncii11-3 43
RANGE OF VARIABLE
VARIABLE RANGE
1. Tack welding Kinds of tacking
1.1 Bridge tacking
1.2 Permanent tacking
1.3 Temporary tacking

2. Visually and 2.1 Acceptable tack welds

dimensionally 2.2 Fully fused to the base metal
acceptable 2.3 Free from defects and discontinuities
2.4 Evenly distributed

3. Root gap 3.1 WPS requirements

3.2 Client requirements

4. Backing materials 4.1 Stiffeners

4.2 Backing plate
4.3 Strong back

5. Alignment 5.1 Codes and specifications

5.2 Client requirements

Weldncii11-3 44
UNIT OF COMPETENCY : USE HAND TOOLS

UNIT CODE : MEE721205

UNIT DESCRIPTOR : This unit covers the competencies required to use hand
tools.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Select hand tools 1.1 Hand tools selected are appropriate to the
requirements of the task.
1.2 Unsafe or defective tools are identified and
marked for repair according to procedure.

2. Use hand tools 2.1 Hand tools are used to produce the desired
outcomes to job specifications.
2.2 Task performed in accordance with company or
industry safety procedure.

3. Maintain hand tools 3.1 Routine maintenance of hand tools is

undertaken according to standard operating
procedures, principles and techniques.
3.2 Hand tools are stored in designated location in
accordance with manufacturer’s
instruction/standard operating procedure.

Weldncii11-3 34
UNIT TITLE : REPAIR WELDS

UNIT CODE : MEE721209

DESCRIPTOR : This unit covers the skills, knowledge and attitudes in

repairing welds.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Mark/locate weld 1.1 Identified weld defects marked/located according to
defects recommended practice
1.2 Weld defects are located and marked according to
procedures

3. Prepare tools and 2.1 Tools and equipment are prepared based on job
equipment requirements and provision of wind barriers.
2.2 Task is performed in accordance with company or
industry requirements and safety procedure

3. Remove defects 3.1 Weld defects are removed/excavated in accordance with

approved industry procedures or client requirements.
3.2 Removal of non-defective welds is minimized and
cleaned.
3.3 Visual and dye-penetrant test is performed to verify the
extent of removal of defects, where applicable
3.4 Welding inspector is informed to verify the extent of
defect removal.
3.5 Task is performed in accordance with company or
industry requirement and safety procedure

4. Perform re-welding 4.1 Re-welding is performed in accordance with approved

repair procedure.
4.2 Task is performed in accordance with company or
industry requirement and safety procedure
4.3 Re-welding is performed with no new weld
defects or damages occurred
4.4 Weld visually checked after re-welding for acceptability

Weldncii11-3 46
RANGE OF VARIABLE
VARIABLE RANGE
1. Weld defects 1.1 Porosity
1.2 Root undercut
1.3 and solid material inclusion
1.4 Concavity/convexity
1.5 Degree of reinforcement
1.6 Burn Through
1.7 Crater cracks
1.8 Cracks
1.9 Lack of Fusion (tie-in)
1.10 Pinholes/Blowholes
1.11 Under Fill
1.12 Excess/incomplete penetration
1.13 Overlap
1.14 Misalignment
1.15 Distortion

2. Tools and equipment 2.1 Welding machine and accessories

2.2 Gouging outfit and accessories
2.3 Portable grinder
2.4 Chipping hammer
2.5 Files
2.6 Extension cord and lightings
2.7 Barriers
2.8 Dye-penetrant kit

3. Removed/excavated Defects removed by

3.1 Grinding
3.2 Arc/air Gouging
3.3 Cutting (mechanical, gas)
3.4 Plasma gouging

Weldncii11-3 47
 EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate
competency repaired weld defects within the approved weld
repair procedures

2. Underpinning knowledge 2.1 Interpretation of weld repair procedures and

WPS
2.2 Causes and identification of weld defects
2.3 Materials and consumables
2.4 Welding Equipment and Tools
2.5 Welding Codes (symbols)
2.6 Repair techniques
2.7 Selection and use of PPE

3. Underpinning skills 3.1 Operating weld defect removal tools and

equipment
3.2 Applying correct weld techniques
3.3 Measuring skills
3.4 Communication skills
3.5 Rectifying weld defects
3.6 Handling welding tools and equipment
3.7 Handling materials and consumables
3.8 Identifying weld defects

4. Resource implications The following resources must be provided:

4.1 Weld defect removal and repair facilities and
equipment
4.2 Supplies and materials
4.3 PPE
4.4 Relevant documentation such as WPS and
approved repair procedure

5. Method of assessment Competency must be assessed through:

5.1 Observation and interview
5.2 Performance record

6. Context of assessment Competency to be assessed while a task is being

undertaken in the workplace or in a simulated
workplace setting.

Weldncii11-3 48
UNIT TITLE : PREPARE WELD MATERIALS

UNIT CODE : MEE721206

DESCRIPTOR : This unit covers the skills, knowledge and attitudes in

preparing welding materials.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the range of Variables
1. Set up cutting 1.1 Cutting equipment should be operational and should
equipment conform to acceptable OH&S standards
1.2 Set up cutting equipment is appropriate for operation
intended

2. Cut and prepare edge 2.1 Materials are cut based on specified
of materials dimension/specifications.
2.2 Task is performed in accordance with company or
industry requirements and safety procedure.

3. Clean surfaces and 3.1 Surfaces are cleaned to required specifications.

edges 3.2 Task is performed in accordance with company or
industry requirements and safety procedure

4. Prepare welding 4.1 Consumables are prepared in accordance with

consumables required specifications
4.2 Welding consumables are prepared in accordance with
manufacturer’s instructions

5. Prepare welding 5.1 PPE should conform to acceptable OH&S

safety and protective requirement and standards
equipment

Weldncii11-3 37
RANGE OF VARIABLE
VARIABLE RANGE
1. WPS WPS Requirements
1.1 Welding positions
1.1.1 1F-4F
1.1.2 1G-3G
1.2 Material thickness
1.2.1 1.6mm and above
1.3 Type of material
1.3.1 Alloy-steel plates
1.4 Consumables
1.4.1 filler wire (diameter)
1.4.2 shielding gas (CO2 or other available mixed
gas)
1.5 Travel speed
1.6 Current setting (polarity, amperage, voltage)
1.7 Shielding gas flow rate
1.8 Welding accessories
1.9 Types of metal transfer
1.10 Joint preparation

2. Defects 2.1 Porosity

2.2 Undercut
2.3 Arc Strike
2.4 Elongated intrusion
2.5 Concavity/convexity
2.6 Degree of reinforcement
2.7 Burn Through
2.8 Crater cracks
2.9 Cracks
2.10 Lack of Fusion
2.11 Pinholes/Blowholes
2.12 Under Fill
2.13 Overlap
2.14 Misalignment
2.15 Distortion

Weldncii11-3 50
EVIDENCE GUIDE
1 Critical aspects of Assessment requires evidence that the candidate
competency welded alloy steel plates using GMAW in 2G and
3G positions to acceptable standards following
approved WPS.

2 Underpinning knowledge 2.1 Drawing/Plan/WPS interpretation

2.2 Materials and consumables
2.2.1 Filler wire for alloy-steel materials
2.2.2 Shielding gases
2.3 Welding Equipment and Tools
2.4 Basic Mathematics (MDAS)
2.5 Welding Codes
2.6 Interpretation of weld defects

3 Underpinning skills 3.1 Measuring skills

3.2 Communication skills
3.3 Rectifying weld defects
3.4 Applying welding techniques for GMAW
3.5 Handling welding tools and equipment
3.6 Handling materials
3.7 Philippine OH&S Rules and/or client’s safety
procedure

4 Resource implications The following resources must be provided:

4.1 GMAW facilities and equipment
4.2 Supplies and materials
4.3 PPE
4.4 Fumes extractor
4.5 Relevant documentation such as WPS and
working drawing
4.6 Stand-by fire fighting equipment

5 Method of assessment Competency must be assessed through:

5.1 Performance test (demonstration) and oral
questioning
5.2 Portfolio

6 Context of assessment Competency to be assessed while a task is being

undertaken in the workplace or in a simulated
workplace setting.

Weldncii11-3 51
UNIT OF COMPETENCY : Weld alloy-steel pipes using GMAW

UNIT CODE : MEE721118

DESCRIPTOR : This unit covers the skills, knowledge and attitudes

in welding alloy-steel pipes using GMAW process.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Perform root pass 1.1 Root pass is performed in accordance with WPS and/or
(backing material) client specifications.
1.2 Weld is visually checked for defects and repaired, as
required
1.3 Weld is visually acceptable in accordance with applicable
codes and standards

2. Clean root pass 2.1 Root pass is cleaned and free from defects and
discontinuities
2.2 Task is performed in accordance with approved WPS

3. Weld subsequent/ 3.1 Subsequent/ filling passes is performed in accordance

filling passes with approved WPS
3.2 Weld is visually checked for defects and repaired, as
required
3.3 Weld is visually acceptable in accordance with applicable
codes and standards

4. Perform capping 4.1 Capping is performed in accordance with WPS and/or

client specifications
4.2 Weld is visually checked for defects and repaired, as
required
4.3 Weld is visually acceptable in accordance with applicable
codes and standards

Weldncii11-3 52
UNIT TITLE : SET UP WELDING EQUIPMENT

UNIT CODE : MEE721207

DESCRIPTOR : This unit covers the skills, knowledge and attitudes in

preparing equipment for welding.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1.1 Set up welding 1.1 Requirements for welding is determined from job
machine requirements, welding procedures and specifications
and/or technical drawings.
1.2 Welding machine is set up in accordance with job
requirements, welding procedures and specifications,
technical drawings and manufacturer’s instructions.
1.3 Welding machine should be connected to an
independent power supply and wired up or set to the
polarity indicated in the welding procedures
/specifications or as recommended by the
manufacturer.
1.4 Current, voltage, and wire feed settings is fine-tuned or
adjusted consistent with job requirements to produce
acceptable weld.
1.5 Task is completed without causing damage to the tools,
equipment and materials and injury to self and others.

2. Set up welding 2.1 Welding machine accessories and consumables are

accessories identified from job requirements, welding procedures
and specifications.
2.2 Welding machine accessories and consumables are set
up in accordance with job requirements, welding
procedures and specifications and/or manufacturer’s
instructions.
2.3 Spools firmly locked to holder, rollers adjusted to
correct tension.
2.4 Purging hoses, damps, flow meter, regulators, torches
and guns are properly installed where needed.
2.5 Gas tanks properly secured where needed.

3. Set up welding 3.1 Braces, stiffeners, rails and other jigs are provided and
positioners, jigs and in conformity with job requirements.
fixtures 3.2 Work items/materials are protected from strong winds,
drafts and rainfall

4. Set up pre-heating 4.1 Pre-heating equipment appropriate to the job

tools/equipment as requirement and specifications
required 4.2 Equipment operated in conformance with the
manufacturer’s instructions.

Weldncii11-3 40
EVIDENCE GUIDE
1 Critical aspects of Assessment requires evidence that the candidate
competency welded alloy-steel pipes using GMAW process in
2G and 5G and/or 6G positions to acceptable
standards following the approved WPS.

2 Underpinning knowledge 2.1 Drawing/Plan/WPS interpretation

2.2 Materials and consumables
2.2.1 Electrode wire
2.2.2 Shielding gases (mixed gases)
2.3 GMAW Welding Equipment and Tools
2.3.1 GMAW mode of metal transfer
2.3.2 GMAW welding accessories
2.4 Basic Mathematics (MDAS)
2.5 Welding Codes (symbols)
2.6 Interpretation of weld defects and GMAW
equipment malfunctions
3 Underpinning skills 3.1 Measuring skills
3.2 Communication skills
3.3 Rectifying weld defects
3.4 Applying welding techniques for GMAW
3.5 Handling welding tools and equipment
3.6 Handling materials and consumables and
checking purity of shielding gas
3.7 Ability to perform root pass with GTAW or
SMAW process
4 Resource implications The following resources must be provided:
4.1 GMAW facilities and equipment
4.2 Supplies and materials
4.3 Fumes extractor
4.4 PPE
4.5 Relevant documentation such as WPS and
working drawing
4.6 Stand-by fire fighting equipment
5 Method of assessment Competency must be assessed through:
5.1 Observation and interview
5.2 Demonstration and interview
5.3 Written test
5.4 Portfolio (work records, certificates, awards,
endorsements, etc…)

6 Context of assessment Competency to be assessed while a task is being

undertaken in the workplace or in a simulated
workplace setting.

Weldncii11-3 54
 SECTION 3 TRAINING STANDARDS

These guidelines are set to provide the Technical and Vocational Education
and Training (TVET) providers with information and other important requirements to
consider when designing training programs for GAS METAL ARC WELDING
(GMAW).

This includes information on curriculum design; training delivery; trainee entry

requirements; tools and equipment; training facilities; and trainers qualification,
among others.

3.1 CURRICULUM DESIGN

Course Title: GAS METAL ARC WELDING NC Level III

Suggested Nominal Training Hours: 20 hrs. ( Basic Competencies)

56 hrs. ( Common Competencies)
72 hrs. ( Core Competencies)

Course Description:

This course is designed to enhance the knowledge, skills and attitudes

of trainees in Gas Metal Arc Welding in accordance with industry standards. It
covers core competencies such as Welding alloy steel plates and pipes using
GMAW.

BASIC COMPETENCIES

Unit of Assessment
Learning Outcomes Methodology
Competency Approach
1. Lead 1.1 Communicate information  Group  Observation
workplace about workplace processes. discussion  Interviews
communicati 1.2 Lead workplace discussions.  Role Play
on 1.3 Identify and communicate  Brainstorming
issues arising in the
workplace
2. Lead small 2.1 Provide team leadership.  Lecture  Demonstration
teams 2.2 Assign responsibilities among  Demonstration  Case studies
members.  Self-paced
2.3 Set performance expectation (modular)
for team members.
2.4 Supervise team performance
3. Develop and 3.1 Identify relevant information in  Direct  Written test
practice planning negotiations observation  Practical/
negotiation 3.2 Participate in negotiations  Simulation/ role performance
skills 3.3 Document areas for playing test
agreement  Case studies
Weldncii11-3 55
4. Solve 4.1 Explain the analytical  Direct  Written test
workplace techniques. observation  Practical/
problem 4.2 Identify the problem.  Simulation/role performance
related to 4.3 Determine the possible playing test
work cause/s of the problem.  Case studies
activities
5. Use 5.1 Identify mathematical tools  Direct  Written test
mathematica and techniques to solve observation  Practical/
l concepts problem  Simulation/role performance
and 5.2 Apply mathematical playing test
techniques procedures/solution  Case studies
5.3 Analyze results
6. Use relevant 6.1 Identify appropriate  Direct  Written test
technologies technology observation  Practical/
6.2 Apply relevant technology  Simulation/role performance
6.3 Maintain/enhance relevant playing test
technology  Case studies

COMMON COMPETENCIES

Unit of Learning Outcomes Methodology Assessment

Competency Approach
1. Apply Safety 1.1 Identify hazardous areas  Lecturette  Oral
Practices 1.2 Use protective clothing and  Practical questioning
devices application  Written
1.3 Perform safe handling of  Demonstratio
tools, equipment and n
materials
1.4 Perform first aid
1.5 Use fire extinguisher
2. Interpret 2.1 Identify standard alphabet of  Lecturette  Oral
working lines  Practical questioning
drawings and 2.2 Identify orthographic/ application  Written
sketches isometric views
2.3 Interpret standard drawing
symbols, dimensional
tolerances and notations

3. Perform 3.1 Perform four fundamental  Lecturette  Oral

Industry operations  Practical questioning
calculations 3.2 Perform conversion of units application  Written test
3.3 Perform calculations on
algebraic expressions
3.4 Compute percentage and
ratio

Weldncii11-3 56
UNIT TITLE : FIT UP WELD MATERIALS

UNIT CODE : MEE721208

DESCRIPTOR : This unit covers the skills, knowledge and attitudes in fitting
up welding materials.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Perform tack welding 1.1 Tack welding is performed in accordance with the
requirements of WPS and client’s specifications.
1.2 Tack welding is performed visually and dimensionally
acceptable.
1.3 Backing plate, stiffener, running plate installed as
required.
1.4 Joints are free from rust, paints, grease and other
foreign materials prior to fit up or tacking.

2. Check gap and 2.1 Root gap is performed in accordance with the
alignment requirements of WPS.
2.2 Alignment within the range of acceptability of code and
standard.
2.3 Fitted materials visually free from stresses

3. Set up welding 3.1 Weld specimen positioned and secured according to the
positioner requirements.

Weldncii11-3 43
 CORE COMPETENCIES

Unit of Learning Outcomes Methodology Assessment

Competency Approach
1. Weld Alloy 1.1 Perform multiple pass fillet  Lecturette  Observation
Steel Plates weld in different positions  Demonstration and oral
Using GMAW (1F-4F) questioning
1.2 Perform multiple pass groove  Demonstration
weld in different positions and oral
(1G-3G) questioning
 Written test

2. Weld Alloy 2.1 Perform groove weld on pipe  Lecturette  Observation

Steel Pipes in different positions  Demonstration and oral
Using GMAW (2G-5G and /or 6G) questioning
 Demonstration
and oral
questioning
 Written test

Weldncii11-3 58
3.2 TRAINING DELIVERY

The delivery of training should adhere to the design of the curriculum.

Delivery should be guided by the 10 basic principles of competency-
based TVET.

 The training is based on curriculum developed from the competency

standards;
 Learning is modular in its structure;
 Training delivery is individualized and self-paced;
 Training is based on work that must be performed;
 Training materials are directly related to the competency standards and the
curriculum modules;
 Assessment is based in the collection of evidence of the performance of
work to the industry required standard;
 Training is based both on and off-the-job components;
 Allows for recognition of prior learning (RPL) or current competencies;
 Training allows for multiple entry and exit; and
 Approved training programs are Nationally Accredited

The competency-based TVET system recognizes various types of

delivery modes, both on and off-the-job as long as the learning is driven
by the competency standards specified by the industry. The following
training modalities may be adopted when designing training programs:

 The dualized mode of training delivery is preferred and recommended. Thus

programs would contain both in-school and in-industry training or fieldwork
components. Details can be referred to the Dual Training System (DTS)
Implementing Rules and Regulations.
 Modular/self-paced learning is a competency-based training modality
wherein the trainee is allowed to progress at his own pace. The trainer just
facilitates the training delivery.
 Peer teaching/mentoring is a training modality wherein fast learners are
given the opportunity to assist the slow learners.
 Supervised industry training or on-the-job training is an approach in training
designed to enhance the knowledge and skills of the trainee through actual
experience in the workplace to acquire specific competencies prescribed in
the training regulations.
 Distance learning is a formal education process in which majority of the
instruction occurs when the students and instructor are not in the same
place. Distance learning may employ correspondence study, audio, video or
computer technologies.

Weldncii11-3 59
3.3 TRAINEE ENTRY REQUIREMENTS

Trainees or students wishing to gain entry into these course should possess
the following requirements:

 completed training in SMAW NC III and NC IV or a holder of

GMAW NC II
 can communicate either oral and written
 physically and mentally fit
 can perform basic mathematical computation

3.4 LIST OF TOOLS, EQUIPMENT AND MATERIALS

Recommended list of tools and materials per trainee for GAS METAL ARC
WELDING - NC III

TOOLS EQUIPMENT MATERIAL

(for 25 trainees) (for 25 trainees) (per trainee)
Qty. Description Qty. Description Qty. Description
25 pcs. Chipping 12 units GMAW/Mig 1 reel Mig wire,
Hammer Welding machine, ER309
Mig gun and
accessories
75 pcs. Steel brush 12 pcs. Welding 38 pcs. Mild steel
positioners plate 3.2mm
X 50mm X
150mm
12 pcs. Plier/tongs 12 units Portable disc 40 pcs Mild steel
grinder plate 10mm X
100mm X
150mm
20 pcs. Files-bastard 1 unit Exhaust fan 21 prs 6” dia. Sch.
cut (or equiv 40
jts) A-53 Gr. B
25 pcs. Welding Mask 2 units Work bench w/ 38 pcs. Cutting disc
bench vice on 4 3/32” x 5/8” x
corners 4” dia.

25 sets Leather 2 sets Oxy- 19 pcs. Grinding disc

apron/jacket acetylene/Oxy- 1/4” x 5/8” x
LPG cutting outfit 4” dia.
50 sets Leather gloves, 1 unit Pedestal /bench 5 cyl. CO2
long grinding machine
5 pcs. Safety goggles, 1 unit Industrial fan 1 cyl. oxygen
wide vision,
clear

Weldncii11-3 60
UNIT TITLE : REPAIR WELDS

UNIT CODE : MEE721209

DESCRIPTOR : This unit covers the skills, knowledge and attitudes in

repairing welds.

ELEMENTS PERFORMANCE CRITERIA

Italicized terms are elaborated in the Range of Variables
1. Mark/locate weld 1.1 Identified weld defects marked/located according to
defects recommended practice
1.2 Weld defects are located and marked according to
procedures

3. Prepare tools and 2.1 Tools and equipment are prepared based on job
equipment requirements and provision of wind barriers.
2.2 Task is performed in accordance with company or
industry requirements and safety procedure

3. Remove defects 3.1 Weld defects are removed/excavated in accordance with

approved industry procedures or client requirements.
3.2 Removal of non-defective welds is minimized and
cleaned.
3.3 Visual and dye-penetrant test is performed to verify the
extent of removal of defects, where applicable
3.4 Welding inspector is informed to verify the extent of
defect removal.
3.5 Task is performed in accordance with company or
industry requirement and safety procedure

4. Perform re-welding 4.1 Re-welding is performed in accordance with approved

repair procedure.
4.2 Task is performed in accordance with company or
industry requirement and safety procedure
4.3 Re-welding is performed with no new weld
defects or damages occurred
4.4 Weld visually checked after re-welding for acceptability

Weldncii11-3 46
* This area can also be used by other welding courses.
** Area requirement is equivalent to 30% of the total teaching/learning areas

3.6 TRAINERS QUALIFICATIONS FOR GMAW WELDER

TRAINER QUALIFICATION (TQ III)

 Must be a holder of GMAW NC III

 Must have completed training in SMAW NC III
 Must have undergone training on Training Methodology III (TM III)
 Must be physically and mentally fit
 *Must have at least 2 years job/industry experience
 Must be a civil service eligible (for government position or appropriate
professional license issued by the Professional Regulatory Commission)

* Optional. Only when required by the hiring institution

Reference: TESDA Board Resolution No. 2004 03

3.7 INSTITUTIONAL ASSESSMENT

Institutional Assessment is to be undertaken by trainees to determine the

achievement of units of competency. A certificate of achievement is issued for
each unit of competency.

Weldncii11-3 62
SECTION 4 NATIONAL ASSESSMENT AND CERTIFICATION ARRANGEMENTS

4.1 To attain the National Qualification of GMAW III, the candidate must
demonstrate competence in all the units of competency listed in Section 1.
Successful candidates shall be awarded a National Certificate signed by the
TESDA Director General.

4.2 Assessment shall focus on the core units of competency, weld alloy steel
plates and weld alloy steel pipes using GMAW.The basic and common units
shall be integrated or assessed concurrently with the core units.

4.3 The following are qualified to apply for assessment and certification:

4.3.1 Graduates of formal, non-formal and informal including enterprise-

based training programs.

4.3.2 Experienced workers (wage employed or self employed)

4.4 The guidelines on assessment and certification are discussed in detail in the
"Procedures Manual on Assessment and Certification" and "Guidelines on the
Implementation of the Philippine TVET Qualification and Certification System
(PTOQS)".

Weldncii11-3 63
 Competency Map
Metals and Engineering Sector
(WELDING)

Weld carbon Weld carbon Weld alloy steel Weld alloy steel Weld carbon Weld carbon Weld carbon
steel plates steel plates plates using pipes using steel plates steel pipes steel plates
CORE COMPETENCIES

using SMAW and pipes SMAW SMAW using GTAW using GTAW using GMAW
using SMAW

Perform gas Perform gas Weld plates Weld pipes Weld alloy steel Weld carbon Weld alloy
welding in welding in alloy using SAW using SAW plates using steel pipes steel pipes
carbon steel steel plates GTAW using GMAW using GMAW
plates and tubes and tubes

Weld carbon Weld carbon Weld alloy Weld alloy Weld alloy steel Weld alloy
steel plates steel pipes steel plates steel pipes pipes using steel plates
using FCAW using FCAW using FCAW using FCAW GTAW using GMAW
COMPETENCIES

Apply safety Interpret drawing Perform industry Contributes to Use hand

practices and sketches calculations quality system tools
COMMON

Prepare weld Set-up welding Fit up weld Repair welds

materials equipment materials

Receive and Demonstrate Participate in Work in team Lead in Develop and Use mathematical
respond to work values workplace environment workplace practice concepts and
workplace communication communication negotiation skills techniques
communication
COMPETENCIES

Work with Practice basic Practice career Practice Lead small Solve problems Use relevant
BASIC

others housekeeping professionalism occupational teams related to technologies

procedures health and safety work activities
procedures

Utilize specialist Develop team Apply problem- Collect, analyze Plan and Promote
communication and individual solving and organize organize work environmental Legend
skills techniques information protection
in the workplace
GMAW NC III
Weldncii11-3 64
DEFINITION OF TERMS

1) base metal – the metal that is to be worked or welded

2) weld bead – a deposit of filler metal from a single welding pass

3) weld defect– an irregularity that spoils the weld appearance or impairs the
effectiveness of the weld or weldment by causing weakness or
failure

4) weld line – the junction of weld metal and the base metal, or the junction of
base metal parts when filler metal is not used

5) weldment – an assembly or structure whose component parts are joined by

welding

6) welding – joining two metals by applying heat to melt and fuse them, with
or without filler metal

7) welding electrode – the current-carrying rod used to strike an arc between rod
and metal

8) welding rod – filler metal in the form of a rod or heavy wire

9) welding torch –a gas mixing and burning tool for the welding of metal

Weldncii11-3 65
 ACKNOWLEDGEMENTS

The Technical Education and Skills Development Authority (TESDA) wishes to

extend thanks and appreciation to the many representatives of business,
industry, academe and government agencies who donated their time and
expertise to the development and validation of this Training Regulation.

THE INDUSTRY EXPERTS

MR. ANTONIO M. REYES MR. ARIEL S. MANALO
Pilipinas Shell Foundation, Inc. Bobcock Hitachi Phil., Inc.
San Isidro, Batangas City San Roque, Bauan, Batangas

MR. ROLANDO S. PEREZ MR. ROLANDO TORRES

EEI Corp. AG & P
Sta. Maria, Bauan, Batangas San Roque, Bauan, Batangas

MR. MOISES C. LACORTE MR. SAMUEL M. CUNANAN

TESDA IV RTC Norwegian Training Center
Batangas City TESDA Complex, Taguig, Metro Manila

The PARTICIPANTS in the Validation of this Training Regulation

MR. EFREN B. IBAÑEZ MR. JACOB L. BACANI
Tribol Trading and Fabrication Philippine Welding Society
47E Morning Star TESDA Complex
Quezon City Taguig, Metro Manila

MR. ROSAULIO R. GUIRNALDA MR. JIMMY LIBO-ON RUZGAL

Bureau Veritas Phils MFI Staff Union
Magsaysay Center Meralco Foundation Inc.
1680 Roxas Blvd. Ortigas Ave., Pasig

MR. VIRGILIO D. MALANA MS. SHELLA S. DEL MUNDO

EEI Corporation Philippine Welding Society
12 Manggahan St., TESDA Complex
Bagumbayan, Quezon City Taguig, Metro Manila

The Members of the TESDA Board

The TESDA Executive Committee
The MANAGEMENT and STAFF of the TESDA Secretariat

Weldncii11-3 66