Scribd
Upload
188 views2 pages

Seismic Force For Components: II III IV ### IV ### B ### A 0.100 B 0.050 C 3.000 D 3.000 E 1.50 F 1.00 ### 5a

This document summarizes the seismic force calculations for an architectural component according to ASCE 7-05 specifications. It provides the input data for the calculation including occupancy category, soil site class, spectral accelerations, and dimensions of the component. It then shows the results, including site coefficients, maximum spectral response accelerations, design spectral response accelerations, seismic design category, amplification and response modification factors, and the calculated component seismic force.

Uploaded by

Franklyn Genove
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
188 views2 pages

Seismic Force For Components: II III IV ### IV ### B ### A 0.100 B 0.050 C 3.000 D 3.000 E 1.50 F 1.00 ### 5a

This document summarizes the seismic force calculations for an architectural component according to ASCE 7-05 specifications. It provides the input data for the calculation including occupancy category, soil site class, spectral accelerations, and dimensions of the component. It then shows the results, including site coefficients, maximum spectral response accelerations, design spectral response accelerations, seismic design category, amplification and response modification factors, and the calculated component seismic force.

Uploaded by

Franklyn Genove
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 2

"IBC2003E.

xls" Program
Version 1.6

SEISMIC FORCE FOR COMPONENTS


ASCE 7-05 Specifications
For Architectural Components
Job Name: Subject: II
Job Number: Originator: Checker: III
IV
Input Data: ###
Occupancy Category = IV Seismic Use Group III ,IBC Table 1604.5 ###
Soil Site Class = B ###
A
Spectral Accel., SS = 0.100 B
Spectral Accel., S1 = 0.050 C
Average Roof Height, h = 3.000 m D
Height of attachment, z = 3.000 m E
Importance Factor, Ip = 1.50 ASCE 7-05 section 13.1.3 F
Component Weight, Wp = 1.00 ###
Component Type = 5a

Results:
2a
Site Coefficients: 2b
Fa = 1.000 ASCE 7-05 table 11.4-1 3a
Fv = 1.000 ASCE 7-05 table 11.4-2 3b
3c
Maximum Spectral Response Accelerations: 4a
SMS = 0.100 SMS = Fa*SS, ASCE 7-05 eq. 11.4-1 4b
SM1 = 0.050 SM1 = Fv*S1, ASCE 7-05 eq. 11.4-2 4c
5a
Design Spectral Response Accelerations for Short and 1-Second Periods : 5b
SDS = 0.067 SDS = 2*SMS/3, ASCE 7-05 eq. 11.4-3 6a
SD1 = 0.033 SD1 = 2*SM1/3, ASCE 7-05 eq. 11.4-4 7a
8a
Seismic Design Category: 9a
Category(for SDS) = A IBC Table 1616.3(1), page 326 9b
Category(for SD1) = A IBC Table 1616.3(2), page 326 10a
Use Category = A Most critical of either category case above controls 11a
12a
Amplification and Response Modification Factors: 12b
Amplification Factor, ap = 1.00 ASCE 7-05 table 13.5-1
Response Modifier, Rp = 2.50 ASCE 7-05 table 13.5-1

Component Seismic Force:


Fp = 0.05 Fp = (0.4*ap*SDS*Wp)*(1+2*z/h)/(Rp/Ip), Eqn. 13.3-1
Fp(max) = 0.16 Fp = 1.6*SDS*Ip*Wp, ASCE 7-05 Eqn. 13.3-2
Fp(min) = 0.03 Fp = 0.3*SDS*Ip*Wp, ASCE 7-05 Eqn. 13.3-3
Use: Fp = 0.05 Note: Fp is to be applied in both transverse and longitudinal
directions relative to seismic restraint.
Comments:

1 of 2 10/14/2020 12:49:54
"IBC2003E.xls" Program
Version 1.6

2 of 2 10/14/2020 12:49:54

You might also like