Pocket Oscilloscope
DSO201
is a pocket size digital storage oscilloscope fulfills basic electronic
engineering requirements. It is base on ARMCortex™-M3compatible 32 bit
platform, equipped with 320*240 color display, SD card capability, USB
connection, and chargeable batteries. Weighs only 60g! Portable Digital
Oscilloscope DIY Kit provides waveform viewing, pocket size and over 2 hours
battery operation. This DIY kit is a open source code. The Schematic, PCB layout
and program code is free for re-design. It is ideal for production test, research,
design and education.
DS0201
Specification
Display2.8″ Color TFT LCDDisplay
Resolution 320×240Display 65K Color
Analog bandwidth 0 - 1MHz
Max sample rate 1Msps 12BitsSample
memory depth 4096 Point
Horizontal sensitivity 1uS/Div～10S/Div (1-2-5 Step)
Horizontal position adjustable with indicator
Vertical sensitivity 10mV/Div～10V/Div (with ×1 probe)
0.5V/Div～10V/Div (with ×10 probe)
Vertical position adjustable with indicator
Input impedance >500KΩ
Max input voltage 80Vpp (by ×1 probe)
CouplingDCTrig modes Auto, Norma, Single, None and Scan
Functionalities:Automatic
measurement: frequency, cycle, duty,
Vpp, Vram, Vavg and DC voltage
Precise vertical measurement with
markers
Precise horizontal measurement with
markers
Rising/falling edge trigger
Trig level adjustable with indicator
Trig sensitivity adjustable with
indicator
Hold/run feature
Test signal Built-in 10Hz～1MHz (1-2-5 Step)
Waveform storage Micro SD card
PC connection via USBas SD card reader
Upgrade by bootloader via USB
Power supply 3.7V Chargeable Lithium battery / USB
Dimension (w/o probe) 106mm X 55mm X 9.9mm
http://shop58663480.taobao.com/
1
DS0201
LCD Display Information
http://shop58663480.taobao.com/
2
DS0201
Basic usage
The UI could be divided to 4 parts: main menu (top), functions (right column), status bar
(bottom), and waveform & markers displays. Use cursor ↑ , ↓, ←, → to navigate among the three
operational parts and make adjustments.
Waveform & Markers
Green waveform – current signal being monitored
Purple waveform – reference waveform loaded from SD card.
Voltage measure marker V1 and V2 (Dot, vertical) – A voltage measure value between
V1-V2 could be displayed.
Time measure marker A and B (Dot line, horizontal) – A time measure value between A
and B could be displayed.
Y positions marker (Purple) – Y position center line for adjustment reference
Trigger level marker (Yellow) – Used to set trigger level
Menu
Horizontal main menu on top of screen, Navigate by ←, → adjust by ↑, ↓.
http://shop58663480.taobao.com/
3
DS0201
Sync. Mode : When blinking, press ↑and ↓to select 4 different synchronization
mode: AUTO, NORM, SING, and NONE.
Auto - Automatic synchronous sweeping mode, displays waveform even not triggered.
Normal - Normal synchronous sweeping mode, displays whenever trigged.
Single – Single sweeping mode, display when triggered, then stopped with latest
Triggered waveform.
NONE – Random sampling mode
SCAN – Scan mode, to check long period low frequency signal.
Vertical Scale : When blinking, press ↑ and ↓ to select different level of sensitivity.
Total 19 scales are optional from 10mV/Div to 100V/Div. Note 1: If you use scale above
20V/Div, please use probe with attenuation of 10:1). Note 2: If newly set scale does not
match reference waveform, the latter will be cleared.
Horizontal sensitivity : When blinking, press ↑ and ↓ to select different sensitivities. ,
from 1uS/Div to 10S/Div total 22 grades. Note 2: If newly set sensitivity does not match
reference waveform, the latter will be cleared.
Y position : When blinking, press ↑ and ↓ to adjust the vertical position of the waveform. Press ‘M’ to
hide/activate Y position marker if needed.
Calculation Mode : Auto calculation modes include:
FREQN – Signal frequency
CYCLE – Signal period
DUTY – Duty time
Vpp – AC signal peak-peak value
Vram – AC signal effective value
Vavg – AC signal average value
DC.V – DC signal average value.
Power supply mode : Power supply by internal battery or USB port. Battery bar will be displayed when
powered from internal.
http://shop58663480.taobao.com/
4
DS0201
Functions
Vertical function buttons on side of screen, Navigate by ↑, ↓ adjust by ←, →.
Trigger sensitivity : When blinking, press ← and → to adjust trigger sensitivity, trigger level
marker (Yellow dotted area) changes correspondingly.
Trigger Type : When blinking, press ← and → to choose trigger mode of rising edge or falling edge.
Probe attenuation scale : When blinking, press ← and → to choose 1:1 or 1:10 probe.
Save waveform : When blinking, status bar will display “ Save Filexxx”, press ← and → to select
file name with xxx = 000-255. Press ‘M’ to save current waveform on display to SD card.
Load waveform : When blinking, status bar will display “ Save Filexxx”, press ← and → to select
file name with xxx = 000-255. Press M to load current waveform to display from SD card.
Note : current version has no file creation function, a FILEXXX.DAT must be prepared
by connecting to PC by USB.
Ref. square wave freq. : When blinking, press ← and → to adjust the frequency of reference
square wave.
Horizontal position adj. : When blinking, press ← and → to scroll waveform horizontally.
Index Bar : Show current display position of total loaded wavefrom
Status Bar
Time markers .: When blinking, press ← and → to adjust T1 or T2 time measure marker, the time
difference PT=T1-T2 will be displayed.
Voltage markers : When blinking, press ← and → to adjust V1 or V2 time measure marker, the
Voltage difference PV=V1-V2 will be displayed.
Trigger level : When blinking, press ← and → to adjust trigger level, trigger level marker (Yellow
dotted line) changes correspondingly.
Save Settings
Hold “R/S” Button and press “M” button to save current settings as default.
http://shop58663480.taobao.com/
5
