4.

Error codes
GENIUS MT Display Status overview shows error codes.
New codes for the GENIUS MT are marked yellow.

Table 2
Error
Descritpion What to do
code
1 Door open  Close the door / operating panel.
 Check the door switch, inside the
operating panel. Is the magnet lost
(Inside the door frame)?
 EB 30 Door switch blinking
 Only units with electro-mechanic closing
007 Door doesn’t open mechanism
40 Invalid reference 
temperature
111 Probe chamber 1 (top)  Check probe 0,789mV at 20°C,
No signal, Oven will NOT operate with a defective
with TC-AddOn Board probe.
Short cut
Probe chamber 2
(bottom)  Check probe 0,789mV at 20°C,
112 No signal, Oven will NOT operate with a defective
with TC add on board probe.
short cut chamber 2
Core probe  Check probe 0,789mV at 20°C,
113
No signal sensor 1 Meat probe operation is possible
Core probe  Check probe 0,789mV at 20°C,
114
No signal sensor 2 Meat probe operation is possible
Core probe  Check probe 0,789mV at 20°C,
115
No signal sensor 3 Meat probe operation is possible
Core probe  Check probe 0,789mV at 20°C,
116
No signal sensor 4 Meat probe operation is possible
Probe waste water (drain)  Check probe 0,789mV at 20°C,
117
No signal Oven will operate with a defective probe.
Temperature too high  Sensor TC2 value above 400°C
119
sensor 1 Oven will not operate
Temperature too high  Sensor TC3 value above 400°C
120
sensor 2 Oven will not operate
No operation if core probe is activated
Core probe temperature
121 Warning if core probe not used
too high
 Sensor TC1 above 400°C
Condensate temperature
122  Warning, Sensor TC4 above 400°C
too high
Temperature too low
 Sensor TC2 value below -30°C
124 Cooking chamber
Oven will NOT operate
(top)
Temperature too low
 Sensor TC3 value below -30°C
125 Cooking chamber
Oven will NOT operate
(bottom)
No operation if core probe is activated
Core probe temperatur
126 Warning if core probe not used
too low
 Sensor TC1 value below -30°C
Temperature to low Warning
128
Condensate  Sensor TC4 value below -30°C

32
 No operation if core probe is activated
Core probe sensor
130 Warning if core probe not used
defective
 No signal of all 4 core probe sensorsl
211 Upper safety thermal  Reset the upper safety thermal release.
release  If the STR has not released, check if the
motor temperature sensor switched off,
this is a bi-metal trip, which reset itself
when cooled down. If so, control if the
main/motor fuses. Replace and check
possible causes: Defective motor
windings or the motor is blocked.
 Oven cannot operate!
Lower safety thermal  Reset the lower safety thermal release.
release  If the STR has not released, check if the
212 motor temperature sensor switched off,
this is a bi-metal trip, which reset itself
when cooled down. If so, control if the
main/motor fuses. Replace and check
possible causes: Defective motor
windings or the motor is blocked.
 Oven cannot operate!
No motor signal  Check the main / motor fuses. Replace
them, if blown and check possible
causes: Defective motor windings or the
motor is blocked.
213  Check motor parameters for start up
and slow down. See programming
manual.
 Units with frequency converter may
block operation when switched Off/On
instantly. Please wait 5 seconds after
switch off before switch on again.
 Oven cannot operate!
No water / low water  Open the water tap.
311
pressure  The water flow pressure must be
checked, 2 bar / 29 PSI for soft water.
 Autoclean will pause until pressure
is high enough.
Information
313 Hand shower off  Hand shower disabled via service
menu.
Sensor filling level water
314  Warning for ovens with water tank
tank
315 Flow meter waste water  Ovens with waste water tank will stop
No water pressure during Autoclean: Stop
316
cleaning  Refer code 311
Flow meter solenoid
317  Warning, only for 2 chamber ovens
valve 2 no request
Correct solenoid valve 1 Attention
318
(top)  Check amount of water upper chamber
Correct solenoid valve 2 Attention
319
(bottom)  Check amount of water upper chamber
Attention
320 Hand shower blocked  Hand shower dissabled at temperatures
above 230°C
Warning
400 Air filter dirty
 Clean filter

33
 Warning
401 Air filter missing
 Install Filter
Warning
 Clean air filter, located at the bottom of
511 PCB temperature 65°C the front panel.
 Check if the compartment fan and the
fan in the front
 Clean air filter, located at the bottom of
the front panel.
512 PCB temperature 70°C  Check if the compartment fan and the
fan in the front.
Oven will not operate
Warning: PCB  Slow overheated PCB.
temperature 68°C  The installation prevents ambient air
513
flow for a cooling effect.
Oven will not operate
 Check the Polarity of the power line
34 Polarity error
Oven will not operate
 Switch unit Off/On
81 Software error
Oven will not operate
 Switch unit Off/On
82 Implausible values
Oven will not operate
 Missing I/O board
83 Simulation mode
Oven will not operate
 Connection I/O-board missing
 Check cable on port X22 (CPU) and
84 Software error
X81 (I/O)
Oven will not operate
 Missing link to I/O board
86 Lost communication
Oven will not operate
 Check gasboard
 Check connection gas board, CPU and
87 Gas Board not connected
IO Board
Oven will not operate
40 InvalidRefTemp 1 Warning
41 InvalidRefTemp 2 Warning
 Errors on 2 reference temperatures
 If error comes up several times, replace
42 InvalidRefTemp1+2
IO board
Oven will not operate
Error temperature sensor
 Please contact Eloma
44 1, heating with no vissible
Oven will not operate
effect
Error temperature sensor
 Please contact Eloma
45 2, heating with no vissible
Oven will not operate
effect
 1) Check temperature sensors
 2) Check cables and connectors
Communication error
46
sensor 1  3) Replace IO Board
Oven will not operate

 1) Check temperature sensors

34
  1) Check connector (bridge) on TCC
Temperature sensor 2 or Add On board
48 TC add on board short  2) Check temperature sensor
cut to earth  3) Replace IO Board
Oven will not operate
 1) Check core probe
Error Condensate
49  2) Replace IO board
temperature sensor
Oven will not operate
 Hardware issue, no logging etc.
988 Retain Data corrupted
Replace CPU
Warning
 Pre heat set point not reached after 2
800 PreHeat TimeOut hours
 Check heating
 Check program settings
Warning
551 USB malfunction  Missing USB stick on active port
 Stick or port defective
Attention
600 Cleaner
 15% of chemical is left over
Attention
601 Rinse
 15% of chemical is left over
Attention
604 Cleaner
 30% of chemical is left over
Attention
605 Rinse
 30% of chemical is left over
No flame upper chamber  Is the phase at L1, polarity!
 Is the kitchen ventilation system
711
working? Interlock?
 Check the ionisation current of the gas
firing
Reset: Pressing restart.
No flame lower chamber  Is the phase at L1, polarity!
 Is the kitchen ventilation system
712
working? Interlock?
 Check the ionisation current of the gas
firing
Reset: Pressing restart.
713 Time out from error 711 Pause, see 711
714 Time out from error 712 Pause, see 712

35