Name: ___________________________________ Yr.
and Section _______________ Date: ______________________
1. A motorcycle weighing 15 kN is on a hill that makes an a. Compressible fluids
angle of 20o with the horizontal. Find the components of b. Incompressible fluids
the motorcycle’s weight parallel and perpendicular to the c. Real fluids
road. d. Ideal fluids
a. 5.1 kN and 14.1 kN 11. If the absolute pressure at the bottom of the ocean is 300
b. 5.1 kN and 13.3 kN kPa, how deep is the water at this point?
c. 7.1 kN and 15.3 kN a. 16.66 m
d. 9.1 kN and 17.3 kN b. 19.66 m
2. A ball is thrown upward from the edge of a cliff with an c. 29.66 m
initial velocity of 7 m/s. How fast is it moving 4 sec later? d. 39.66 m
a. 42 m/s upward direction 12. An open chamber rests on the ocean floor in 160 ft of sea
b. 42 m/s downward direction water (SG = 1.03). What air pressure in psig must be
c. 33 m/s upward direction maintained inside to exclude water?
d. 33 m/s downward direction a. 45.6
3. A car towing a trailer is accelerating on a level road. The b. 71.4
car exerts a force on the trailer whose magnitude is c. 60.9
a. The same as that of the force the trailer exerts on the d. 93.2
13. A thermodynamic system which undergoes a cyclic process
car
during a positive amount of work is done by the system.
b. The same as that of the force the trailer exerts on the a. Heat engine
road b. Heat pump
c. The same as that of the force the road exerts on the c. Reversible-irreversible process
road d. Reversed rankine cycle
d. Greater than that of the force the trailer exerts on the 14. Ratio of the outlet stagnation pressure to the inlet
car stagnation pressure is referred as:
a. Diffuser efficiency
4. In Newton’s third law of motion, the action and reaction
b. Nozzle efficiency
forces c. Isentropic efficiency
a. Act on the same object d. Weir flow efficiency
b. Act on different objects 15. How much energy is required to just vaporize a kg of water
c. Do not necessarily have the same magnitude and do which is originally at 27 C and one atmosphere?
not necessarily have the same line of action. a. 2562.65 kJ
d. Have the same magnitude but do not have b. 3562.65 kJ
c. 4562.65 kJ
necessarily the same line of action.
d. 5562.65 kJ
5. Find the torsional stress in MPa in a 40 mm diameter shaft 16. What mass of nitrogen is contained in a 65 m3 tank if the
that transmits 20.53 kW at 600 rpm. pressure and temperature are one atmosphere and 21 C
a. 26 MPa respectively?
b. 46 MPa a. 75.4 kg
c. 36 MPa b. 57.4 kg
d. 56 MPa c. 54.7 kg
6. A steel shaft 1.4375 inches in diameter transmits 40 hp at d. 45.7 kg
1400 rpm. Assuming a modulus of rigidity of 12 x 10 6 psi, 17. The total income equals the total operating cost:
find the torsional deflection of the shaft in degrees per a. Balance sheet
foot length. b. Check and balance
a. 0.246 c. In-place value
b. 0.624 d. Break-even-no-gain-no-loss
c. 0.426 18. What is the work-in process classified as:
d. 1.246 a. A revenue
7. The maximum stress to which a material may be subjected b. A liability
before failure occurs: c. An expense
a. Ultimate strength d. An asset
b. Ultimate stress 19. The initial cost of a paint sand mill, including its
c. Endurance limit installation, is P800,000. The BIR approved life of this
d. Tensile stress machine is 10 years for depreciation. The estimated
8. The capacity of metal to withstand load without breaking salvage value of the mill is P50,000, and the cost of
is: dismantling is estimated to be P15,000. Using straight line
a. Strength depreciation, what is the annual depreciation charge?
b. Stress a. P75,000
c. Elasticity b. P85,000
d. Strain c. P76,500
9. The flow of liquid at a constant rate through a conical pipe d. P90,000
is _____. 20. Find the nominal rate which if converted quarterly could
a. Steady nonuniform be used instead of 12% compounded semi-annually.
b. Steady uniform a. 10.58%
c. Unsteady nonuniform b. 11.28%
d. Unsteady uniform c. 9.38%
10. Fluids that has constant density is considered is: d. 11.82%
