ITCO-TYPE JUNK BASKETS

Instruction Manual 3050

Itco-Type Junk Baskets

One Company Unlimited Solutions

 Itco-Type Junk Baskets

Itco-Type Junk Baskets

General Description ................................................. 3
Use ............................................................................ 3
Construction ............................................................. 3
Accessories .............................................................. 4
Operation .................................................................. 5
Maintenance ............................................................. 5
Disassembly ............................................................. 5
Reassembly .............................................................. 5
To Reassemble the Catcher ..................................... 6
Principle Dimensions ................................................ 8
I N D E X

Specifications and Replacement Parts

Junk Baskets ................................................. 9 – 10
Catchers ....................................................... 11 – 16
Rock Bit Cone Dimensions .................................... 17

The designs and specifications for the tools

described in this instruction manual were in effect
at the time this manual was approved for printing.
National Oilwell Varco, whose policy is one of
continuous improvement, reserves the right to
discontinue models at any time, or to change
designs and specifications without notice or without
incurring obligation.
Fifteenth Printing, November 2005
General Description Construction
The Bowen Itco-Type Junk Basket is an The Bowen Itco-Type Junk Basket
uncomplicated yet dependable fishing consists basically of a Barrel, a Top Sub,
tool for retrieving all kinds of loose junk. an Upper Catcher, a Lower Catcher, and
Its simplicity of design, construction, a Type “A” Mill Shoe. This type shoe is
operation and maintenance is such that faced with conventional hard metal on
any drilling crew can use it successfully. the cutting surfaces. Accessories include
With free revolving double catchers, Magnet Inserts, Mill Shoes dressed with
magnet inserts and accessory shoes, Itcoloy and Finger Shoes. The two
the Bowen Junk Basket is indispensable catchers employ rivet-free construction,
equipment on a rotary drilling rig. easily redressed on location. Catcher
Fingers are cast from strong, long wear-
Use ing manganese bronze or steel. The
The Bowen Itco-Type Junk Basket is Fingers in the Upper Catcher extend only
used to retrieve all sorts of junk that may half way to the center, its function being
accumulate at the bottom of a well and to break the core when an upward strain
which may impede drilling progress. is taken on the string. The Lower Catcher
This junk may be such objects as rock has alternately long and short fingers
bit cones, bearings, broken slips, bits of which extend almost to the center, form-
wire line, various hand tools, slivers and ing a close fitting basket which will retain
debris from twisted off drill string, milling the core or small pieces of junk. Both
cuttings, etc. It may also be used to take Catchers are free to revolve within the
a core sample, drill a full gauge hole or Shoe, eliminating Finger breakage.
to ream the hole.

Junk Basket Junk Basket Bowen Itco-Type Junk Basket

Lower Catcher Upper Catcher Dressed with a Type A Mill Shoe

3
Accessories
Mill Shoes Finger Shoe
The Bowen Itco-Type Junk Basket is When junk is lying loose on the bottom
furnished with a standard Type “A” Mill of the well or when junk is too large to
Shoe. This is a mill type shoe with side pass through the Catchers, a Finger
wings and is ideal when used in softer Shoe may be installed on the bottom
formations. It is recommended that of the Barrel in place of the Mill Shoe.
Itcoloy-faced Mill Shoes be considered When the Junk Basket engages the fish,
when harder formations are encoun- combined rotating and lowering cause
tered. the long fingers to close in beneath the
fish and retain it in the Barrel. Finger
The Type “B” Mill Shoe is similar in replacements are easy and inexpensive
design to the Type “A” but is hard faced to replace on the Shoe Body.
with Itcoloy. Itcoloy is a material com-
Magnet Inserts
posed of sintered tungsten carbide is an
Magnet Inserts are available to convert
extremely tough matrix which will effec-
Bowen Junk Baskets into effective fishing
tively and rapidly mill up junk during the
magnets. The Magnet Insert is machined
fishing operation. It is ideal when the
to fit into the recess normally occupied
cutting of hard formations is required.
by the two Catchers. The Magnet Insert
is used especially when in hard-to-drill
The Type “C” Mill Shoe is a flat bot-
formations and to thoroughly clean the
tomed shoe which is hard faced with
hole prior to diamond drilling.
Itcoloy on the bottom, on the inner face
and on the outer face. It will effectively
mill up junk and is especially effective for
cutting cores. This is a burning type shoe
for cutting metal.

Bowen Itco-Type Junk Basket

with Magnet Insert

Magnet Insert Finger Shoe Type A Mill Shoe Type B Mill Shoe Type C Mill Shoe

4
Operation Maintenance 5. If the Junk Basket is to be used
First determine that the Bowen Itco-Type The Bowen Itco-Type Junk Basket is a again, immediately inspect the
Junk Basket is properly assembled and relatively simple tool to maintain. For Catchers to assure they are not
that all parts are in good working order. best operation and long service life the damaged and that all the Fingers
(see “Reassembly”) following procedure should guide the work properly. If any damaged is
operator: found, disassemble and replace
Select the proper shoe:
If the junk is large and lying loose on the 1. After use, the Junk Basket should the damaged parts, or use a spare
bottom, use the Finger Shoe. be completed disassembled and Catcher. (see “Redressing Catcher
cleaned (see “Disassembly”) Assemblies”)
If the formation is relatively soft and the
fish is loose, use a Type “A” Mill Shoe. 2. Inspect and replace as may be 6. Thoroughly clean and lubricate all
required any small parts, such as internal parts, and the interior of all
If the formation is hard or the fish is im- the outside parts.
springs and fingers, that may be
bedded in the formation, use either the
damaged.
Type “B” or Type “C” Itcoloy-faced Mill Reassembly
Shoe. Also, these hard faced shoes will 3. Reassemble, greasing each internal 1. Clamp the Barrel in a pipe vise.
cut away protruding excess metal to al- part as it is assembled.
2. Make up the Top Sub to the Barrel.
low free entry of the junk into the basket.
4. Dry and dope threaded connections
3. Insert the Lower Catcher into the
Connect the assembly to the drill string as they are assembled.
Shoe. The Lower Shoe is the one
and run it into the hole. Just before
5. After complete assembly, the entire with alternate long and short
reaching bottom, start circulation at
outside of the Junk Basket should Fingers. Insert the Upper Catcher
reduced pressure, begin rotation and
be painted or thoroughly greased, into the Shoe above the Lower
slowly lower to contact the fish and
to prevent deterioration. Catcher.
bottom. Continue to rotate as weight is
increased, permitting the Shoe to pene- Disassembly Caution
trate the information. Penetrating the 1. Break the threaded joints between The Fingers hinge upward in operation.
formation forces the junk completely into the Top Sub and Barrel, and be- Make sure that both Catchers are
the Barrel and cuts a short core. tween the Barrel and Shoe. This may installed so that they deflect upward
After the core is cut, stop rotation and best be done at the rig as the Junk in service. Also make sure that both
circulation, release the torque from the Basket is removed from the hole. Catchers are well greased just before
string, then take an upward strain to assembly, and that both rotate freely
2. Remove the Shoe from the Barrel. If
break the core. A Bowen Hydraulic Jar in the Shoe.
the assembly is a large one, it may
made up in the string above the Bowen be necessary to use a lifting sub When the Magnet Insert is used , it is
Junk Basket will aid in quickly breaking and large pipe vise to facilitate hand- inserted into the same recess as both
the core. ling. It the Junk Basket is disassem- Catchers, with its bail uppermost.
As soon as the core is broken, the string bled in horizontal position in a vise,
4. Make up the Shoe and its inserted
and Basket may be removed from the care should be taken that the
Catchers (or Magnet Insert) to the
well. Catchers do not fall out as the Shoe
lower end of the Barrel.
is removed.
At the surface, break the joint between 5. Tighten the two joints.
the Shoe and the Barrel, remove the 3. Lift out the two Catchers (or Magnet
Shoe and empty the Basket. Insert) with their retrieved junk. 6. Paint or thoroughly lubricate the
entire outside of the Junk Basket
NOTE: 4. Remove the Top Sub from the
to prevent deterioration.
When using Mill Shoes, maintain a ton of weight Barrel.
and rotate the Basket at a mill cutting rate of 50
to 150 rpm.
When using Finger Shoes, rotate and lower
slowly until approximately two tons of weight is
against the bottom.

5
Redressing 1. Check the Catcher replacement parts 7. Slip the Retainer Ring over the upper
Catcher Assemblies
list to assure that the Proper Fingers part of the Body, with the two holes at
To Disassemble the Catcher in correct quantity are being used the bottom side. These two holes are
Completely disassemble the Catcher. (see pages 11–16). Grease all parts 180° apart. They should be aligned
The only tools required are a suitable thoroughly. with the two tapped holes in the Body.
screwdriver (with a 1¦4" blade) and a vise
2. Assemble a Torsion Spring in one of 8. Shove the Retainer Ring down,
if the Catcher is large.
the Long Fingers, so that one leg of deflecting the Torsion Spring legs until
Referring to the photos on page 7, the Torsion Spring is inserted into the the bottom edge of the Retainer Ring
proceed as follows: small hole at the upper end of the rests on the series of shoulders near
Finger, and the other leg of the Torsion the center of the Body.
1. Place the Catcher assembly on a work-
Spring is protruding out toward the
bench or in a vise, with the Retainer NOTE:
code letter on the Finger. If the Catcher is very large, two people may be
Ring at the top. Do not exert enough
NOTE: required to assemble the Retainer Ring; one
force against the Catcher with vise
Some Catcher assemblies do not have Fingers maintaining the Fingers and Torsion Springs in
jaws to maul or distort it. place, while the second pushes the Retainer Ring
with integral lugs. These assemblies utilize
separate Pivot Pins. Fingers used in these down.
2. Remove the two Retainer Screws.
assemblies are assembled with the Torsion The total force exerted by the Torsion Springs in
3. Remove the Retainer Ring. This should Spring maintained in position by the pivot pin. large Catchers may be too great for one person
be done slowly and with care. The to comfortable overcome.
3. Insert the Finger with its assembled
Retainer Ring holds the several Torsion
Torsion Spring into any one of the
Springs deflected so that when the 9. Align the two holes in the Retainer
open slots in the side of the Body. The
Retainer Ring is partially disassem- Ring, with the two tapped holes in the
two pilot lugs on the Finger will nest
bled, it will tend to spring off due to the Body.
into the smaller cross-slots at the
spring load behind it. If it is allowed to
upper end of the Finger slot. 10. Insert the two Retainer Screws, and
spring off unrestricted, parts may be
tighten, making sure that the heads
lost or damaged. Caution
are completely centered in the
Be sure to insert the Finger with the code
4. Remove the Fingers and the Torsion Retainer Ring holes, and does not
letter toward the outside of the Catcher.
Springs. overlap the edge of the hole.
These Fingers must be free to revolve
5. Remove the Torsion Springs from the inward toward the center of the Catcher Do not over-tighten these two screws.
Fingers. when the Retainer Ring is installed, and
11. Check the action of each of these
the Fingers must be free to deflect
6. Remove the Pivot Pins where these assembled Fingers to assure proper
upward when in service after assembly.
are used. deflection and retraction.
4. Install the first short Finger next to the
7. Clean all parts thoroughly, and inspect The Catcher is now ready for assembly in
first long Finger, in the same manner.
them for damage or excessive wear. the Junk Basket.
Replace any parts not in good service 5. Install a second long Finger.
condition.
6. Continue installation of long and short
To Reassemble the Catcher
Fingers, alternately until all have been
All Catchers are assembled by the same installed.
method, but more care must be taken After all Fingers have been installed, each
with the Lower Catcher than with the Finger will have one leg of the Torsion
Upper Catcher to assure that alternate Spring extending outward approximately
long and short fingers assembled are in 1¦4" to 1¦2", depending on size. Do not trim
the proper sequence. off these Torsion Spring legs. They are
necessary to the function of the Catcher
Fingers.

6
 Long Finger
Short Finger
Torsion Spring
Retainer Ring

Body

Retainer Screw

Parts to Assemble
Bowen Junk Basket Catcher

Assembled Bowen Junk Basket Catcher

(Lower)

7
 Maximum
Fish Diameter
I.D. of
Catcher
Principle Dimensions
Part Standard O.D. of Max.
Number Hole Size Hardfaced Shoe Fish Dia. A B C D E F G H I J K L
14590 3-3/4 – 4-1/8 3-5/8 – 4-1/8 2-23/32 26-1/ 4 8-1/ 4 * 23 26-5/ 8 † 1-7/ 8 3-5/ 8 2-23/ 32 3-5/ 8 2-9/ 32 1-7/ 8
14586 4-1/4 – 4-1/2 4-1/16 – 4-1/2 2-31/ 32 26-3/ 8 8-3/ 8 15-27/ 32 23-1/ 8 26-3/ 4 † 2-1/ 8 3-1/ 4 2-31/ 32 4-1/ 16 3-23/ 32 2-5/ 16
14595 4-5/8 – 5 4-1/2 – 5 3-9/32 27-1/ 8 9-1/ 8 15-11/ 16 23-7/ 8 27-1/ 2 † 2-3/ 8 3-7/ 8 3-9/ 32 4-1/ 2 4-1/ 16 2-3/ 8
19375 4-5/8 – 5 4-1/2 – 5 3-3/8 27 9 15-11/ 16 23-3/ 4 27-5/ 8 13 2-3/ 8 3-7/ 8 3-13/ 32 4-1/ 2 4-7/ 64 2-7/ 16
14600 5-1/8 – 5-1/2 4-1/8 – 5-1/2 3-9/ 32 26-15/ 16 8-15/ 16 51-1/ 16 23-15/ 16 27-9/ 16 † 2-3/ 4 4-1/ 4 3-23/ 32 4-7/ 8 4-17/ 32 2-5/ 8
2618 5-5/8 – 6 5-1/8 – 5-3/4 3-25/32 29-7/ 8 11-7/ 8 * 26-5/ 8 30-5/ 8 † 3-3/ 4 5-1/ 8 3-25/ 32 5-1/ 8 4-1/ 2 2-5/ 8
14605 5-5/8 – 6 5-3/8 – 6 4-1/16 29-3/ 16 11-3/ 16 15-47/ 64 25-15/ 16 29-11/ 16 † 3 4-3/ 4 4-1/ 16 5-3/ 8 4-15/ 16 2-25/ 32
2670 6-1/8 – 6-1/2 5-3/4 – 6-1/2 4-3/8 30-1/ 4 11-15/ 16 * 47-1/ 4 31-1/ 4 † 4 5-3/ 4 4-13/ 32 5-3/ 4 5-5/ 32 2-13/ 16
14610 6-1/8 – 6-5/8 5-7/8 – 6-5/8 4-5/16 30-11/ 16 12-11/ 16 15-5/ 8 27-7/ 16 31 † 3-5/ 16 5-1/ 8 4-5/ 16 5-7/ 8 5-3/ 8 2-7/ 8
19379 6 – 6-3/8 5-7/8 – 6-3/8 4-1/2 30-11/ 16 12-11/ 16 15-5/ 8 27-7/ 16 28 13 3-1/ 2 5-1/ 8 4-7/ 32 5-7/ 8 5-15/ 32 2-7/ 8
14615 6-3/4 – 7-1/4 6-1/4 – 7-1/4 4-3/16 31-1/ 4 13-1/ 4 15-3/ 4 28 32-1/ 4 † 3-1/ 2 5-3/ 4 4-13/ 16 6-1/ 4 5-3/ 4 3-1/ 16
14620 7-3/8 – 8-1/4 7-1/8 – 8-1/4 5-7/16 31-3/ 4 13-3/ 4 15-11/ 16 28-1/ 2 31-3/ 4 † 4-5/ 8 6-1/ 2 5-7/ 16 7-1/ 8 6-7/ 16 3-5/ 16
14625 8-3/8 – 91/4 8-1/8 – 9-1/4 6-3/16 33-1/ 4 15-1/ 4 15-11/ 16 29-1/ 2 33-1/ 2 † 5-1/ 8 7-1/ 2 6-3/ 16 8-1/ 8 7-3/ 16 3-13/ 16
14630 9-3/8 – 101/4 9-1/8 – 10-1/4 7-3/16 34-1/ 4 16-1/ 4 15-11/ 16 30-5/ 8 34-5/ 8 † 6-1/ 8 8-1/ 2 7-3/ 16 9-1/ 8 8-3/ 16 4-5/ 16
14635 10-3/8 – 11-7/8 10-1/8 – 117/8 8-1/ 16 35-7/ 8 17-7/ 8 15-5/ 8 32-1/ 8 37-1/ 8 † 6-1/ 2 9-3/ 8 8-1/ 16 10-1/ 8 9-3/ 8 5
14640 11-3/4 – 14-1/4 11-1/4 – 141/4 9-1/ 16 37-5/ 16 19-1/ 16 15-13/ 16 33-5/ 16 38-5/ 16 † 7-1/ 4 10-3/ 8 9-1/ 16 11-1/ 4 10-7/ 16 5-3/16
14645 12-5/ 8 – 15 12-1/4 – 15 10-1/ 16 44-5/ 8 22-5/ 8 19-9/ 16 40-3/ 8 50-1/ 8 † 7-1/ 2 11-3/ 8 10-1/ 16 12-1/ 4 11-3/ 8 6
14650 14-3/4 – 18 14-1/2 – 18 12-1/ 16 50-3/ 4 26-3/ 4 21 46 52-1/ 4 † 9-1/ 4 13-3/ 4 12-1/ 16 14-1/ 2 13-5/ 8 7

* Flush from Shoe to Sub

† Length to order, specify box or pin connection.

8
Specifications
Hole Size 3-3/4 to 4-1/8 4-1/4 to 4-1/2 4-5/8 to 5 4-5/8 to 5 5-1/8 to 5-1/2 5-3/8 to 6 5-5/8 to 6 6-1/8 to 6-1/2 6-1/8 to 6-1/2
O.D. Barrel (Top End) 3-5/8 3-3/4 3-7/8 3-7/8 4-1/4 5-1/8 4-3/4 5-3/4 5-1/8
O.D. Shoe (Top End) 3-5/8 4-1/16 4-1/2 4-1/2 4-7/8 5-1/8 5-3/8 5-3/4 5-7/8
Maximum Diameter of Fish 2-11/16 2-15/16 3-9/32 3-3/8 3-23/32 3-25/32 4-1/16 413/32 4-5/16
Number of Teeth 8 8 8 8 8 8 8 8 8
Complete Assembly Part No. 14590 14586 14595 19375 14600 2618 14605 59996 14610
Weight 55 60 65 65 80 80 100 200 110

Replacement Parts
Top Sub Part No. 14725 14726 14727 14727 14728 2619 14729 59997 14730
Weight 20-1/2 21-1/2 22 22 23-1/8 23 29-1/2 42 30-1/2
Barrel Part No. 14591 14587 14596 19376 14601 2620 14606 15134 14611
Weight 2528 32 31 40 40 48 48 55
Upper Catcher Part No. — — — — — — 14607-W 15130-W 14612-W
Weight — — — — — — 3 3 3
Lower Catcher Part No. 14593-W 14589-W 14598-W 19377-W 14603-W 21735-W0 14608-W 28349-W 14613-W
Weight 1-1/2 1-1/2 2 2 2-1/2 2-1/2 3 3
Conventional Shoe Part No. 14594-A 14574-A 14599-A 19378-A 14604-A 2625-A 14609-A 2676-A 14614-A
Type A (Hard-Faced) Weight 8 8 14 10 14 16 16 18-1/2 18-1/2

Mill Shoes – Extra

Mill Shoe Type B Part No. 14954-B 14574-B 14599-B 19378-B 14604-B 2625-B 14609-B 2676-B 14614-B
(Itcoloy-Faced) Weight 10 10 12 12 16 18 18 22 22
Mill Shoe Type C Part No. 14594-C 14574-C 14599-C 19378-C 14604-C 2625-C 14609-C 2676-C 14614-C
(Itcoloy-Faced) Weight 12 12 14 14 18 25 25 30 30

Finger Shoes – Extra

To Fit Basket Number 14590 14586 14595 19375 14600 2618 14605 2670 14610
Maximum Diameter of Fish 3-1/4 3-13/16 4-1/16 4-1/16 4-1/2 4-1/2 4-3/4 5-1/4 5-3/8
Replacement Part No. 22203 22206 22207 22207 22208 22208 22209 22218 19406
Weight 6 8 10 10 12 12 16 18 20

Finger Shoe replacement is furnished with the same O.D. as the standard shoe unless otherwise specified.

Magnet Inserts – Extra

To Fit Basket Number 14590 14586 14595 19375 14600 2618 14605 2670 14610
Total Pull in Lbs. 45 – 55 45 – 55 80 – 100 80 – 100 80 – 100 80 – 100 180 – 205 180 – 205 180 – 205
Complete Assembly Part No. 61842-M 61838-M 61858-M 61858-M 61852-M 61852-M 61862-M 61866-M 62637-M
Weight 16 16-1/2 29 29 32 32 55 55 55
Adapter Part No. M-61843 M-61839 M-61859 M-61859 M-61853 M-61853 M-61863 M-61867 M-62638
Weight 2 21/2 3 3 4 4 8 8 8
Magnetic Assembly Part No. M-61812 M-61812 M-61814 M-61814 M-61814 M-61814 M-61816 M-61816 M-61816
Weight 14 14 26 26 28 28 47 47 47

It is recommended that Shoes be at least 1¦8" over the Barrel size.

How to Order
Specify:
(1) Name and number of assembly or part
(2) O.D. and type of shoe
(3) Top connection, if other than standard

RECOMMENDED SPARE PARTS:

(1) 2 Upper Catchers
(2) 2 Lower Catchers
(3) 3 Mill Shoes
(4) 2 Finger Shoes
(5) 4 Finger Shoe Replacements

9
Specifications
Hole Size 6-1/8 – 6-1/2 6-5/8 – 7 7-1/4 – 8 8-1/4 – 9 9-1/4 – 10-1/8 10-1/4 – 11-5/8 11-3/4 – 12-1/2 12-5/8 – 15 15 – 20
O.D. Barrel (Top End) 5-1/4 5-3/4 6-1/2 7-1/2 8-1/2 9-3/8 10-3/8 11-3/8 13-3/4
O.D. Shoe (Top End) 5-7/8 6-1/4 7-1/8 8-1/8 9-1/8 10-1/8 11-1/4 12-1/4 14-1/2
Maximum Diameter of Fish 4-1/2 4-13/16 5-7/16 6-3/16 7-3/16 8-1/16 9-1/16 10-1/16 12-1/16
Number of Teeth 8 8 8 8 10 12 12 12 16
Complete Assembly Part No. 19379 14615 14620 14625 14630 14635 14640 14645 14650
Weight 110 125 160 205 255 290 360 450 655

Replacement Parts
Top Sub Part No. 19380 14731 14732 14733 14734 14735 14736 14737 14738
Weight 30-1/2 42 53 67 86 94 128 140 155
Barrel Part No. 19381 14616 14621 14626 14631 14636 14641 14646 14651
Weight 55 55 68 85 102 117 134 170 265
Upper Catcher Part No. 19382-W 14617-W 14622-W 14627-W 14632-W 14637-W 14642-W 14647-W 14652-W
Weight 3 4 5 7 8 12 14 20 30
Lower Catcher Part No. 19383-W 14618-W 14623-W 14628-W 14633-W 14638-W 14643-W 14648-W 14653-W
Weight 3 4 5 7 8 12 14 20 30
Conventional Shoe Part No. 19384-A 14619-A 14624-A 14629-A 14634-A 14639-A 14644-A 14649-A 14654-A
Type A (Hard-Faced) Weight 181/2 20 28 38 49 55 70 100 175

Mill Shoes – Extra

Mill Shoe Type B Part No. 19384-B 14619-B 14624-B 14629-B 14634-B 14639-B 14644-B 14649-B 14654-B
(Itcoloy Faced) Weight 22 25 34 44 56 62 72 110 190
Mill Shoe Type C Part No. 19384-C 14619-C 14624-C 14629-C 14634-C 14639-C 14644-C 14649-C 14654-C
(Itcoloy Faced) Weight 30 33 43 51 66 72 82 125 215

Finger Shoes – Extra

To Fit Basket Number 19379 14615 14620 14625 14630 14635 14640 14645 14650
Maximum Diameter of Fish 51/2 529/32 61/2 71/4 81/8 915/16 11 117/8 151/4
Replacement Part No. 19406 22210 22211 22212 22213 22214 22215 22216 22217
Weight 20 28 29 37 45 64 71 89 160

Finger Shoe replacement is furnised with the same O.D. as the standard shoe unless otherwise specified.

Magnet Inserts – Extra

To Fit Basket Number 19379 14615 14620 14625 14630 14635 14640 14645 14650
Total Pull in lbs. 180-205 250-290 310-360 425-495 620-720 930-1080 1265-1440 1265-1440 1740-2050
Complete Assembly Part No. 61868-M 61874-M 61949-M 61955-M 61959-M 61969-M 61977-M 61979-M 61987-M
Weight 59 77 98 120 182 268 331 353 467
Adapter Part No. M-61869 M-61875 M-61950 M-61956 M-61960 M-61970 M-61978 M-61980 M-61988
Weight 12 14 19 24 32 47 65 87 113
Magnetic Assembly Part No. M-61816 M-61818 M-61822 M-61824 M-61826 N-61828 N-61830 N-61830 P-61834
Weight 47 63 79 96 150 221 266 266 354

How to Order
Specify:
(1) Name and number of assembly or part
(2) O.D. and type of shoe
(3) Top connection, if other than standard

RECOMMENDED SPARE PARTS:

(1) 2 Upper Catchers
(2) 2 Lower Catchers
(3) 3 Mill Shoes
(4) 2 Finger Shoes
(5) 4 Finger Shoe Replacements

10
Catcher Specifications
Will Fit Junk Basket Number:
Single Catcher — 14590 7724 14586 — 7453 14595 — 7731 — —
Upper Catcher — — — — — — — 10995 — — —
Lower Catcher — — — — — — — — 10995 — —
Catcher Dimensions:
Internal Diameter 1-3¦4 2-23¦32 249¦64 2-31¦32 3-1¦16 3-1¦16 39¦32 3-13¦32 3-13¦32 3-13¦32 3-13¦32
External Diameter 2.075 315¦64 3-11¦16 3-13¦16 3-13¦16 4 3-31¦32 3-31¦32 4-1¦16 4-1¦16 4-9¦32
Height 1-3¦4 1-7¦8 1-7¦8 2-1¦4 2-1¦2 2-1¦2 2-3¦8 1-63¦64 1-63¦64 2-3¦8 2-1¦4
Complete Assembly Part No. 11270-W 14593-W 21810-W 14589-W 22075-W 21780-W 14598-W 21880-W 21805-W 19377-W 18940-W
Weight 7¦8 1 7¦8 1-1/2 2 2 1-3¦4 1-3¦8 1-3¦8 1-3¦4 1-3¦4

Replacement Parts
Body Part No. 42230 45541 45542 45590 45591 45591 45568 45565 45565 45563 45579
Weight 1/2 3/4 5/8 1-1/8 1-1/2 1-1/2 1-1/4 1 1 1-1/4 1-1/4
Finger Retainer Part No. 42253 45543 45538 45562 45592 45592 45569 45566 45566 45564 45580
Weight 1/8 1/8 1/8 1/8 3/16 3/16 3/16 1/8 1/8 3/16 3/16
Short Finger Part No. 42254 45539 45539 45574 45574 45574 55962 45574 45574 55962 45581
Code E E W-3 W-3 W-3 690-W W-3 W-3 610-W W-1
Weight 1/32 1/32 1/32 1/32 1/16 1/16 1/16 1/32 1/32 1/16 1/16
Req’d 8 5 5 5 10 5 6 12 6 6 6
Long Finger Part No. — 45540 45540 45575 — 45575 55963 — 45575 55963 45582
Code — F F W-4 — W-4 691-W — W-4 691-W W-2
Weight — 1/16 1/16 1/16 — 1/8 1/8 — 1/16 1/8 1/8
Req’d — 5 5 5 — 5 6 — 6 6 6
Pivot Pin Part No. 42255 45535 45535 45583 45583 45583 55957 45583 45583 55957 55957
Weight 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 8 10 10 10 10 10 12 12 12 12 12
Torsion Spring Part No. 42256 45567 45567 55958 45571 45571 55958 45571 45571 55958 45571
Weight 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 8 10 10 10 10 10 12 12 12 12 12
Retainer Screw Part No. 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257
Weight 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 2 2 2 2 2 2 2 2 2 2 2
Top Cap Part No. 42252 — — — — — — — — — —
Weight 1/16 — — — — — — — — — —

Code How to Order

Each Finger is stenciled with a Letter or Letter-Number Code. These Codes are used in lieu of the Specify:
Part Number because of space limitations on small Fingers. The Code Numbers indicate Part Numbers (1) Name and number of assembly or part
(2) Finger number and code when ordering Fingers
as follows.

RECOMMENDED SPARE PARTS:

Code Part No. Code Part No. Code Part No. Code Part No.
A 45516 I 45561 P-1 45588 21778-W 45607
(1) 2 Sets Fingers
B 45517 J 45507 P-2 45589 21779-W 45608 (2) 4 Sets Torsion Springs
C 45518 K 45508 W-1 45581 362-W 362 (3) 1 Set Pivot Pins
D — L 45510 W-2 45582 363-W 363 (4) 4 Retainer Screws
E 45539 M 45525 W-3 45574 690-W 45623
F 45540 N 45526 W-4 45575 691-W 45624
G 45557 O — X-1 45597 666-W 666
H 45558 P — X-2 45598 667-W 667

11
Catcher Specifications
Will Fit Junk Basket Number:
Single Catcher — 5516 — — — — — 7737 — — 12097
2168 7441 7441
2570
Upper Catcher 2618 — — — — 14605 — — 14610 2670 —
Lower Catcher — 12109 — 2618 14605 — — 12139 — — 2670
Catcher Dimensions:
Internal Diameter 3-3/4 3-3/4 3-3/4 3-3/4 4-1/16 4-1/16 4-1/16 4-3/32 4-5/16 3-13/32 4-13/32
External Diameter 4-15/32 4-15/32 415/32 4-15/32 4-7/8 4-7/8 4-7/8 4-3/4 5-5/16 4-1/16 5-5/32
Height 29/16 29/16 2-9/16 2-9/16 2-25/32 2-25/32 1-9/16 2-1/2 2-7/8 2-13/16 2-13/16
Complete Assembly Part No. 14747-W 21735-W 31043-W 14603-W 14608-W 14607-W 21960-W 21820-W 14612-W 15130-W 28349-W
Weight 2 2-1/2 2-1/2 2-3/4 3-1/4 3 2 2-1/2 4-1/8 3-1/4 3-1/2

Replacement Parts
Body Part No. 45559 45559 45559 45559 45555 45555 45600 45595 45572 45511 45511
Weight 1-1/2 1-3/4 1-3/4 1-7/8 2 1-3/4 1-1/2 1-3/4 2-1/2 2 2-1/4
Finger Retainer Part No. 45560 45560 45560 45560 45556 45556 45556 45596 45573 45519 45519
Weight 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4
Short Finger Part No. 45558 45558 45558 45558 45558 45558 45558 45597 45517 45517 45517
Code H H H H H H H X-1 B B R
Weight 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16
Req’d 10 5 10 5 6 12 12 6 1212 8
Long Finger Part No. — 45561 — 45561 45557 — — 45598 — — 45516
Code — I — I G — — X-2 — — A
Weight — 1/8 — 1/8 1/8 — — 1/8 — — 1/8
Req’d — 5 — 5 6 — — 6 — — 4
Pivot Pin Part No. — — — — — — — 45599 — — —
Weight — — — — — — — 1/32 — — —
Req’d — — — — — — — 12 — — —
Torsion Spring Part No. 45520 45520 45520 45520 45520 45520 45520 45571 45520 45520 45520
Weight 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 10 10 10 10 12 12 12 12 12 12 12
Retainer Screw Part No. 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257
Weight 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d — 2 2 2 2 2 2 2 2 2 2
Top Cap Part No. — — — — — — — — — — —
Weight — — — — — — — — — — —

Code How to Order

Each Finger is stenciled with a Letter or Letter-Number Code. These Codes are used in lieu of the Specify:
Part Number because of space limitations on small Fingers. The Code Numbers indicate Part Numbers (1) Name and number of assembly or part
(2) Finger number and code when ordering Fingers
as follows.

RECOMMENDED SPARE PARTS:

Code Part No. Code Part No. Code Part No. Code Part No.
A 45516 I 45561 P-1 45588 21778-W 45607
(1) 2 Sets Fingers
B 45517 J 45507 P-2 45589 21779-W 45608 (2) 4 Sets Torsion Springs
C 45518 K 45508 W-1 45581 362-W 362 (3) 1 Set Pivot Pins
D — L 45510 W-2 45582 363-W 363 (4) 4 Retainer Screws
E 45539 M 45525 W-3 45574 690-W 45623
F 45540 N 45526 W-4 45575 691-W 45624
G 45557 O — X-1 45597 666-W 666
H 45558 P — X-2 45598 667-W 667

12
Catcher Specifications
Will Fit Junk Basket Number:
Single Catcher — — 6109 — — — — 5895 — — —
7318 7072
2677 2554
Upper Catcher 19379 — — — 14615 — — — — 14620 —
19385
Lower Catcher — 19379 — — — 14615 — — — — 14620
19385
Catcher Dimensions:
Internal Diameter 4-17/32 4-17/32 4-3/4 4-3/4 4-13/16 4-13/16 5-3/16 5-3/16 5-1/4 5-7/16 5-7/16
External Diameter 5-13/32 5-13/32 5-5/8 5-5/8 5-23/32 5-23/32 6-1/4 6-1/4 6-1/8 6-3/8 6-3/8
Height 2-7/8 2-7/8 2-5/8 2-5/8 3-1/16 3-1/16 3-5/16 3-5/16 2-3/4 3-5/16 3-5/16
Complete Assembly Part No. 19382-W 19383-W 21750-W 22045-W 14617-W 14618-W 22050-W 21725-W 22030-W 14622-W 14623-W
Weight 4 4 4-1/4 4-1/4 4-1/2 5 5-1/4 5-1/4 4-3/4 6 6

Replacement Parts
Body Part No. 45553 45553 45584 45584 45512 45512 45550 45550 45601 45545 45545
Weight 2-1/2 2-1/2 2-3/4 2-3/4 2-7/8 3 3-1/8 3-1/8 2-5/8 3-1/4 3-1/4
Finger Retainer Part No. 45554 45554 45585 45585 45552 45552 45551 45551 45527 45546 45546
Weight 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2
Short Finger Part No. 45517 45517 45517 45517 45517 45517 45557 45557 45517 45517 45517
Code B B B B B G G B B B B
Weight 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/8 1/8 1/8
Req’d 12 6 6 12 12 6 12 6 12 14 7
Long Finger Part No. — 45516 45516 — — 45516 — 45518 — — 45518
Code — A A — — A — C — — C
Weight — 1/8 1/8 — — 1/8 — 3/16 — — 3/16
Req’d — 6 6 — — 6 — 6 — — 7
Pivot Pin Part No. — — — — — — — — — — —
Weight — — — — — — — — — — —
Torsion Spring Part No. 45520 45520 45520 45520 45520 45520 45520 45520 45520 45520 45520
Weight — 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 12 12 12 12 12 12 12 12 12 14 14
Retainer Screw Part No. 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257
Weight — 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 2 2 2 2 2 2 2 2 2 2 2
Top Cap Part No. — — — — — — — — — — —
Weight — — — — — — — — — — —

Code How to Order

Each Finger is stenciled with a Letter or Letter-Number Code. These Codes are used in lieu of the Specify:
Part Number because of space limitations on small Fingers. The Code Numbers indicate Part Numbers (1) Name and number of assembly or part
(2) Finger number and code when ordering Fingers
as follows.

RECOMMENDED SPARE PARTS:

Code Part No. Code Part No. Code Part No. Code Part No.
A 45516 I 45561 P-1 45588 21778-W 45607
(1) 2 Sets Fingers
B 45517 J 45507 P-2 45589 21779-W 45608 (2) 4 Sets Torsion Springs
C 45518 K 45508 W-1 45581 362-W 362 (3) 1 Set Pivot Pins
D — L 45510 W-2 45582 363-W 363 (4) 4 Retainer Screws
E 45539 M 45525 W-3 45574 690-W 45623
F 45540 N 45526 W-4 45575 691-W 45624
G 45557 O — X-1 45597 666-W 666
H 45558 P — X-2 45598 667-W 667

13
Catcher Specifications
Will Fit Junk Basket Number:
Single Catcher — 7751 6228 — — 7754 — — — — —
7010 7567 7015
13003
Upper Catcher 10880 — — — 14625 — — 14630 1100 — —
19388
Lower Catcher — 10880 — 14625 — 10885 14630 — — 11005 —
19388 19391
Catcher Dimensions:
Internal Diameter 5-5/8 5-5/8 6 6-3/16 6-3/16 6-1/2 7-3/16 7-3/16 7-3/16 7-13/16 8-5/16
External Diameter 6-19/32 6-19/32 7 7-1/8 7-1/8 7-7/16 8-1/8 8-1/8 8-1/8 9-1/32 9-3/4
Height 2-7/8 3-5/8 3-7/16 3-13/16 3-13/16 3-1/2 4-5/16 4-5/16 3-3/8 4-5/8 5
Complete Assembly Part No. 21865-W 18936-W 18725-W 14628-W 14627-W 18720-W 14633-W 14632-W 21885-W 18945-W 31046-W
Weight 5-1/2 6-3/4 7 7-1/4 7-1/4 7-1/2 9-1/4 9-1/4 8 10 17-1/4

Replacement Parts
Body Part No. 45602 45514 45505 45547 45547 45515 45521 45521 45504 45522 45576
Weight 3 3-3/4 4 4-1/4 4-1/4 4-1/2 4-1/2 4-1/2 3-1/4 5-1/4 10-1/4
Finger Retainer Part No. 45528 45528 45506 45548 45548 45529 45530 45530 45530 45531 45578
Weight 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1
Short Finger Part No. 45517 45517 45508 47670 47670 45508 45588 45588 45588 45507 45525
Code B B K 362-W 362-W K P-1 P-1 P-1 J M
Weight 1/8 1/8 1/8 1/8 1/8 1/8 3/16 3/16 3/16 3/16 1/4
Req’d 12 6 6 6 12 6 6 12 12 6 16
Long Finger Part No. — 45518 45507 47669 — 45507 45589 — — 70277 —
Code — C J 363-W — J P-2 — — N —
Weight — 3/16 3/16 3/16 — 3/16 1/4 — — 1/4 —
Req’d — 6 6 6 — 6 6 — — 6 —
Pivot Pin Part No. — — — 45536 45536 — — — — — —
Weight — — — 1/16 1/16 — — — — — —
Torsion Spring Part No. 45520 45520 45509 45537 45537 45509 45549 45549 45509 45509 45509
Weight 1/32 1/32 1/16 1/16 1/16 1/16 1/8 1/8 1/8 1/8 1/8
Req’d 12 12 12 12 12 12 12 12 12 12 16
Retainer Screw Part No. 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257 42257
Weight 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 2 2 2 2 2 2 2 2 2 2 2

Code How to Order

Each Finger is stenciled with a Letter or Letter-Number Code. These Codes are used in lieu of the Specify:
Part Number because of space limitations on small Fingers. The Code Numbers indicate Part Numbers (1) Name and number of assembly or part
(2) Finger number and code when ordering Fingers
as follows.

RECOMMENDED SPARE PARTS:

Code Part No. Code Part No. Code Part No. Code Part No.
A 45516 I 45561 P-1 45588 21778-W 45607
(1) 2 Sets Fingers
B 45517 J 45507 P-2 45589 21779-W 45608 (2) 4 Sets Torsion Springs
C 45518 K 45508 W-1 45581 362-W 362 (3) 1 Set Pivot Pins
D — L 45510 W-2 45582 363-W 363 (4) 4 Retainer Screws
E 45539 M 45525 W-3 45574 690-W 45623
F 45540 N 45526 W-4 45575 691-W 45624
G 45557 O — X-1 45597 666-W 666
H 45558 P — X-2 45598 667-W 667

14
Catcher Specifications
Will Fit Junk Basket Number:
Single Catcher — — — — — 2708 —
Upper Catcher — — 14640 — 14645 — —
Lower Catcher — — — 14645 — — —
Catcher Dimensions:
Internal Diameter 8-5/16 8-11/16 9-1/8 10-1/8 10-1/8 1-13/16 1-13/16
Height 4-1/2 5-3/32 5-3/16 6 6 7-5/16 7-5/16
Complete Assembly Part No. 22000-W 31047-W 14642-W 14648-W 14647-W 21775-W 22090-W
Weight 15-3/4 17 19-1/4 24-1/2 24-3/4 29 29

Replacement Parts
Body Part No. 45577 45593 45524 45586 45586 45605 45605
Weight 8-3/4 10 12 17 17-1/4 16-1/2 16-1/2
Finger Retainer Part No. 45578 45594 45533 45587 45587 45606 45606
Weight 1 1 1-1/4 1-1/2 1-1/2 1-3/4 1-3/4
Short Finger Part No. 45525 45507 45507 666 666 45607 45607
Code M J J 666-W 666-W 21778-W 21778-W
Weight 1/4 3/16 3/16 1/4 1/4 5/16 5/16
Req’d 16 16 16 8 16 7 14
Long Finger Part No. — — — 667 — 45608 —
Code — — — 667-W — 21779-W —
Weight — — — 5/16 — 3/8 —
Req’d — — — 8 7 —
Pivot Pin Part No. — — — 45603 45603 45609 45609
Weight — — — 1/8 1/8 3/16 3/16
Req’d — — — 16 16 14 14
Torsion Spring Part No. 45509 45509 45509 45604 45604 45610 45610
Weight 1/8 1/8 1/8 3/16 3/16 1/4 1/4
Req’d 16 16 16 16 16 14 14
Retainer Screw Part No. 42257 42257 42257 42257 42257 42257 42257
Weight 1/32 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 2 2 2 2 2 2 2

Code How to Order

Each Finger is stenciled with a Letter or Letter-Number Code. These Codes are used in lieu of the Specify:
Part Number because of space limitations on small Fingers. The Code Numbers indicate Part Numbers (1) Name and number of assembly or part
(2) Finger number and code when ordering Fingers
as follows.

RECOMMENDED SPARE PARTS:

Code Part No. Code Part No. Code Part No. Code Part No.
A 45516 I 45561 P-1 45588 21778-W 45607
(1) 2 Sets Fingers
B 45517 J 45507 P-2 45589 21779-W 45608 (2) 4 Sets Torsion Springs
C 45518 K 45508 W-1 45581 362-W 362 (3) 1 Set Pivot Pins
D — L 45510 W-2 45582 363-W 363 (4) 4 Retainer Screws
E 45539 M 45525 W-3 45574 690-W 45623
F 45540 N 45526 W-4 45575 691-W 45624
G 45557 O — X-1 45597 666-W 666
H 45558 P — X-2 45598 667-W 667

15
Catcher Specifications
Will Fit Junk Basket Number:
Single Catcher — 7747 — 11292 — —
7005 2690
Upper Catcher — 14635 — — — —

Lower Catcher 14610 — 14635 — 11010 14640

Catcher Dimensions:
Internal Diameter 4-5/16 5-1/4 8-1/16 8-3/16 8-11/16 9-1/8
External Diameter 5-5/16 6-1/8 9-5/16 9-3/4 10-3/32 10-7/16
Height 2-7/8 3-5/16 5 5 5-3/32 5-3/16
Complete Assembly Part No. 14613-W 18935-W 14638-W 21760-W 21840-W 14643-W
Weight 4-1/4 5-1/4 15-1/2 18-1/4 19-1/4 19-1/4

Replacement Parts
Body Part No. 45572 45513 45523 45576 45593 45524
Weight 2-3/4 3 8-1/2 11-1/4 12 12
Finger Retainer Part No. 45573 45527 45532 45578 45594 45533
Weight 3/8 1/2 1 1 1-1/4 1-1/8
Short Finger Part No. 45517 45517 45525 45525 45507 45507
Code B B M M J J
Weight 1/16 1/16 3/16 3/16 3/16 3/16
Req’d 6 6 8 8 8 8
Medium Finger Part No. 45557 45516 45507 45510 45510 45510
Code G A J L L L
Weight 3/32 3/32 1/4 1/4 1/4 1/4
Req’d 3 3 4 4 4 4
Long Finger Part No. 45516 45518 68295 45526 45526 45526
Code A C N N N N
Weight 1/8 1/8 5/16 5/16 5/16 5/16
Req’d 3 3 4 4 4 4
Torsion Spring Part No. 45520 45520 45509 45509 45509 45509
Weight 1/32 1/32 1/16 1/16 1/16 1/16
Req’d 12 12 16 16 16 16
Retainer Screw Part No. 42257 42257 42257 42257 42257 42257
Weight 1/32 1/32 1/32 1/32 1/32 1/32
Req’d 2 2 2 2 2 2

Code How to Order

Each Finger is stenciled with a Letter or Letter-Number Code. These Codes are used in lieu of the Specify:
Part Number because of space limitations on small Fingers. The Code Numbers indicate Part Numbers (1) Name and number of assembly or part
(2) Finger number and code when ordering Fingers
as follows.

RECOMMENDED SPARE PARTS:

Code Part No. Code Part No. Code Part No. Code Part No.
A 45516 I 45561 P-1 45588 21778-W 45607
(1) 2 Sets Fingers
B 45517 J 45507 P-2 45589 21779-W 45608 (2) 4 Sets Torsion Springs
C 45518 K 45508 W-1 45581 362-W 362 (3) 1 Set Pivot Pins
D — L 45510 W-2 45582 363-W 363 (4) 4 Retainer Screws
E 45539 M 45525 W-3 45574 690-W 45623
F 45540 N 45526 W-4 45575 691-W 45624
G 45557 O — X-1 45597 666-W 666
H 45558 P — X-2 45598 667-W 667

16
Rock Bit Cone Dimensions
2-Cone Bits Size 3-Cone Bits
A B A B
— — 3-3/4 – 4-1/8 13-1/32 24-5/64
— — 4-1/4 – 41/2 2-13/64 2-59/64
— — 4-5/8 – 5-21/32 3-13/64
— — 5-1/8 – 5-1/2 2-41/64 3-17/64
— — 5-5/8 – 6 3-1/8 4-1/64

Maximum
— — 6-1/8 – 6-1/2 3-7/64 4-3/16
— — 6-5/8 – 7 3-7/16 4-9/16
— — 7-1/8 – 7-1/2 3-45/64 4-27/32

“A”
3-45/64 5-17/32 7-5/8 – 8 3-31/32 5-17/64
4-11/32 6-7/64 8-1/8 – 8-1/2 4-3/8 5-25/32
4-11/32 6-5/16 8-5/8 – 9 4-17/32 6-1/32
— — 9-1/8 – 9-1/2 4-9/16 6-13/32
4-7/8 7 9-5/8 – 9-7/8 4-15/16 6-41/64
5-23/64 7-19/32 10-1/2 – 11-1/2 5-27/64 7-5/32
5-63/64 8-27/64 11-3/4 – 12-1/2 6-1/8 7-61/64
“B” Diameter
— — 12-5/8 – 131/8 6-5/16 8-31/64 Maximum
— — 13-1/2 – 14-1/4 7-1/32 8-13/16
— — 14-1/2 – 15 7-25/64 9-19/32
— — 16 9-27/32 10-1/8
— — 17 – 17-1/2 8-13/64 11-11/64
— — 18-1/2 – 18-7/8 8-25/32 11-23/64
— — 20 9-1/2 11-7/8
— — 22 10-15/32 14-1/64
— — 24 10-15/16 14-9/16
— — 26 12-19/64 14-31/64

The cone sizes shown are the nominal Hughes Christensen cone
dimensions and are the maximum for the size indicated in the middle
column. They may be used as a guide in junk fishing operations.

17
This page intentionally left blank

18
This page intentionally left blank

19
NATIONAL OILWELL VARCO

Well Service and Completion Solutions

© 2005 National Oilwell Varco

PDF/1118

MANUAL NO. 3050 R2