Scribd
Upload
457 views6 pages

BMX DAI 1604 Input Modules: Subject of This Section

The document provides information about the BMX DAI 1604 input module, including its characteristics and how to connect it. The module has 16 AC input channels and connects via a 20-pin terminal block. It monitors inputs between 100-120 VAC and has thresholds for detecting 1s and 0s. The module also provides a sensor supply voltage and has response times of 10-20ms. Connecting the module involves wiring the AC inputs to a terminal block and including a 0.5A fast blow fuse for protection.

Uploaded by

Leonardo Neira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
457 views6 pages

BMX DAI 1604 Input Modules: Subject of This Section

The document provides information about the BMX DAI 1604 input module, including its characteristics and how to connect it. The module has 16 AC input channels and connects via a 20-pin terminal block. It monitors inputs between 100-120 VAC and has thresholds for detecting 1s and 0s. The module also provides a sensor supply voltage and has response times of 10-20ms. Connecting the module involves wiring the AC inputs to a terminal block and including a 0.5A fast blow fuse for protection.

Uploaded by

Leonardo Neira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Modicon M340 Using Unity Pro

BMX DAI 1604


35012474 07/2012

BMX DAI 1604 Input Modules

9
Subject of this Section
This section presents the BMX DAI 1604 module, its characteristics, and explains
how it is connected to the various sensors.

What Is in This Chapter?


This chapter contains the following topics:
Topic Page
Introduction 104
Characteristics 105
Connecting the Module 107

35012474 07/2012 103


BMX DAI 1604

Introduction

Function
The BMX DAI 1604 module is a 100...120 VAC discrete module connected via a 20-
pin terminal block. This module has 16 input channels that operate on alternating
current.

Illustration

104 35012474 07/2012


BMX DAI 1604

Characteristics

General Characteristics
This table presents the general characteristics for the BMX DAI 1604 and
BMX DAI 1604H (see page 28) modules:

BMX DAI 1604 Module 100...120 VAC inputs


Nominal input values Voltage 100...120 VAC
Current 5 mA
Frequency 50/60Hz
Threshold input values At 1 Voltage ≥ 74 V
Current ≥ 2.5 mA
At 0 Voltage ≤20 V
Current ≤1 mA
Frequency 47 Hz to 63 Hz
Sensor supply 85...132 V
(including ripple)
Peak of current on enabling 240 mA
(at nominal U)
Input impedance at nominal U and f = 55 Hz 13 kΩ
Type of input Capacitive
Response time Activation 10 ms
Deactivation 20 ms
IEC 1131-2 compliance Type 3
Reliability MTBF for continuous 1 303 067
operation in hours at
ambient temperature
(30° C) (86° F)
2-wire / 3-wire proximity sensor compatibility (see Premium and Atrium IEC 947-5-2
using Unity Pro, Discrete I/O modules, User manual)
Dielectric strength 1500 V actual, 50 / 60 Hz for 1 min.
Resistance of insulation >10 MΩ (below 500 VDC)
Sensor voltage: monitoring threshold OK > 82 V
Error < 40 V
Sensor voltage: monitoring response on appearance 20 ms < T < 50 ms
time at 24 V (-15% ... +20%)
on disappearance 5 ms < T < 15 ms
Power consumption 3.3 V typical 76 mA
maximum 107 mA

35012474 07/2012 105


BMX DAI 1604

Sensor supply consumption typical 228 mA


maximum 510 mA
Power dissipation 3.8 W max.
Temperature derating for BMXDAI1604 None

NOTE: Over its extended -25...70° C (-13...158° F) temperature range, the


BMX DAI 1604H characteristics are the same as the BMX DAI 1604 characteristics
in the table.

Fuses

Internal None
External Fast blow fuse of 0.5 A

CAUTION
LOSS OF INPUT FUNCTION
Install the correct type of fuse with the correct rating.
Failure to follow these instructions can result in injury or equipment damage.

DANGER
HAZARD OF ELECTRICAL SHOCK, EXPLOSION OR ARC FLASH
Switch off the sensor and pre-actuator voltages before connecting or
disconnecting the module.
Failure to follow these instructions will result in death or serious injury.

106 35012474 07/2012


BMX DAI 1604

Connecting the Module

At a Glance
The BMX DAI 1604 module is fitted with a removable 20-pin terminal block for the
connection of sixteen input channels.

Input Circuit Diagram


The following diagram shows the circuit of an alternating current input.

35012474 07/2012 107


BMX DAI 1604

Module Connection
The following diagram shows the connection of the module to the sensors.

power supply: 100...120 VAC


fuse: fast blow fuse of 0.5A

108 35012474 07/2012

You might also like