Built-in power supply photoelectric sensor

E3JK
Pre-wired type/E3JK
● Slim body full
Wide range voltage of functions and
economically
power supply available

Connection
Sensor type Shape Sensing distance Output form Output Model
method
Light ON E3JK-5M1
Relay output
Dark ON E3JK-5M2
Through-beam 5m
Light ON/ Dark ON NPN:
DC transistor output
(selectable) E3JK-5S3
* Light ON E3JK-R2M1
Retroreflective Relay output
2.5m Dark ON E3JK-R2M2
model (with
M.S.R. function) (3m) Light ON/Dark ON DC transistor NPN E3JK-R2S3
Pre-wired (selectable) output PNP E3JK-R2R3
models * Light ON E3JK-R4M1
Retroreflective Relay output
4m Dark ON E3JK-R4M2
model (without
M.S.R. function) (5m) Light ON/Dark ON DC transistor output
E3JK-R4S3
(selectable) (NPN)
Light ON E3JK-DS30M1
Relay output
Dark ON E3JK-DS30M2
Diffuse-reflective 300mm
Light ON/Dark ON DC transistor output
E3JK-DS30S3
(selectable) (NPN)
* The value within the parentheses indicates the sensing distance applied when the E39-R2 reflector is used.
Note: The UL-listed model ends with "-US". (Example: E3JK-5M1-US). Note that the DC transistor type of the E3JK is UL-unlisted.

Accessories (Order Separately)

Slits
Minimum sensing
Slit width Sensing distance Model Quantity Remarks
object (typical)
1 pc. each for emitter (Seal type long slit)
Width 1 mmx20 mm E3JK-5## 0.7 m 1 mm dia. E39-S39 and receiver Can be used with the through-
(total 2 pcs.) beam model E3JK-5##.

A-218 Photoelectric Sensors

Reflectors
Name Sensing distance (typical) Model Quantity Remarks
E3JK-R2## 2.5 m (rated value) Attached to the E3JK-R2##.
E39-R1 1

E3JK
E3JK-R4## 4 m (rated value) Attached to the E3JK-R4##.
Reflectors
E3JK-R2## 3m
E39-R2 1 ---
E3JK-R4## 5m
Small reflector E3JK-R2## 1 m (5 mm) * E39-R3 1 ---
E3JK-R2## 750 mm (200 mm) * E39-RS1
Tape Reflector E3JK-R2## 1.2 m (200 mm) * E39-RS2 1 The M.S.R. function is available.
E3JK-R2## 1.5 m (200 mm) * E39-RS3
* Values in parentheses indicate the minimum required distance between the sensor and reflector.
Note: When the reflector used is other than the supplied one, set the sensing distance to about 0.7 times of the typical example as a guideline.

Mounting Brackets
Shape Model Quantity Remarks

E39-L40 1 Supplied with E3JK

Note: If a through-beam model is used, order two Mounting Brackets for the emitter and receiver respectively.

E3JK A-219
Rating/Performance
E3JK
Sensor Retroflective model Retroflective model
Through-beam Diffuse-reflective
type (with M.S.R. function) (without M.S.R. function)
Item Model E3JK-5M# E3JK-5S3 E3JK-R2M# E3JK-R2#3 E3JK-R4M# E3JK-R4S3 E3JK-DS30M# E3JK-DS30S3
2.5 m 4m 300 mm
Sensing distance 5m
(When using the E39-R1) (When using the E39-R1) (White paper 100x100 mm)
Standard sensing
Opaque 14.8 dia. min. Opaque: 75 mm dia. min. ---
object
Differential 20% max. of sensing
---
distance distance
Both emitter and receiver:
Directional angle 1° to 5° ---
3°C to 20°C
Light source
Infrared LED (950 nm) Red LED (660 nm) Infrared LED (950 nm)
(wave length)
Power supply
12 to 240 VDC ±10% ripple (p-p) : 10% max. 24 to 240 VAC ±10% 50/60 Hz
voltage
Cur- DC 3 W max. 2 W max.
rent
con-
sump- AC 3 W max. 2 W max.
tion
DC SSR
DC SSR DC SSR DC SSR
Negative or
Negative Negative Negative
positive
Relay common Relay Relay common Relay common
common
output: 48 VDC output: output: 48 VDC output: 48 VDC
48 VDC
250VAC 100 mA max. 250VAC 250VAC 100 mA max. 250VAC 100 mA max.
Control output 100 mA max.
3 A (cosj=1) Leak current 3 A (cosj=1) 3 A (cosj=1) Leak current 3 A (cosj=1) Leak current
Leak current
max., 5 VDC 0.1 mA max. max., 5 VDC max., 5 VDC 0.1 mA max. max., 5 VDC 0.1 mA max.
0.1 mA max.
10 mA min. With load 10 mA min. 10 mA min. With load 10 mA min. With load
With load
short-circuit short-circuit short-circuit
short-circuit
protection protection protection
protection
Life Me-
ex- chani- 50 million times or more (switching frequency 18,000 times/hour)
pect- cal
ancy
(relay Electri-
100 thousand times or more (switching frequency 18,000 times/hour)
output) cal

Response time 30 ms max. 10 ms max. 30 ms max. 5 ms max. 30 ms max. 5 ms max. 30 ms max. 5 ms max.
Sensitivity
--- Single-turn adjustment
adjustment
Ambient
Incandescent lamp: 3,000 lux max.
illuminance
Ambient
Operating: -25°C to 55°C, Storage: -30°C to 70°C (with no icing or condensation)
temperature
Ambient humidity Operating: 45% to 85%RH, Storage: 35% to 95%RH (with no condensation)
Insulation
20 M W min. at 500 VDC
resistance
Dielectric strength 1,500 VAC at 50/60 Hz for 1 minute
De-
Vibra- struc- 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
tion tion
resis-
tance Mal-
10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
function

A-220 Photoelectric Sensors

 Sensor Retroflective model Retroflective model
Through-beam Diffuse-reflective
type (with M.S.R. function) (without M.S.R. function)
Item Model E3JK-5M# E3JK-5S3 E3JK-R2M# E3JK-R2#3 E3JK-R4M# E3JK-R4S3 E3JK-DS30M# E3JK-DS30S3

E3JK
De-
struc- Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
tion
Destruc-
Shock tion: Destruction: Destruction: Destruction:
resis- 100m/s2 Destruction: 100m/s2 100m/s2 Destruction: 100m/s2 Destruction:
Destruction:
(approx. 500 m/s2 for (approx. (approx. 500 m/s2 for (approx. 500 m/s2 for
tance Mal- 500 m/s2 for
10G) 3 times each 10G) 3 times 10G) 3 times 3 times each 10G) 3 times 3 times each
function 3 times each
3 times in X, Y, and each in X, Y, each in X, Y, in X, Y, and each in X, Y, in X, Y, and
in X, Y and
each in Z directions and Z direc and Z direc Z directions and Z direc Z directions
Z directions
X, Y, and Z tions tions tions
directions
Protective
IEC60529 IP64
structure
Connection
Pre-wired models (standard length: 2 m)
method
Weight
Approx. 420 g Approx. 250 g
(Packed state)
Case ABS
Lens Acrylics
Materi-
al Mount-
ing Steel
bracket
Accessories Mounting bracket (with screws), nuts, instruction manual, reflector (retroreflective model only)

E3JK A-221
Characteristic data (typical)
Excess Gain Ratio vs. Setting Distance
Through-beam model Retroreflective Models Diffuse-reflective
E3JK-5## E3JK-R2## + E39-R1 (supplied reflector) E3JK-DS30##

Excess gain ratio

1,000 100

Excess gain ratio

100
Excess gain ratio

Reflector: E39-R1 Sensing object: White paper

500
50 50
300
30 30
100
50 10 10
30
5 5
10 3 3
5
3 Operating Operating
1
voltage 1 voltage
Operating
1
voltage

0 1 2 3 4 5 6 7 8 0 1 2 3 4 0 100 200 300 400 500

Setting distance (m) Setting distance (m) Setting distance (mm)

E3JK-R4## + E39-R1 (supplied reflector)
100
Excess gain ratio

Reflector: E39-R1
50
30

10

5
3

Operating 1
voltage

0 1 2 3 4 5
Setting distance (m)

A-222 Photoelectric Sensors

Output Circuit Diagram
E3JK
Relay output
Model Timing chart Output circuit

E3JK
E3JK-5M1 24 to 240 VAC
E3JK-5M2 Incident 12 to 240 VDC
Brown Power
Interrupted Main circuit source
E3JK-R2M1 Light indicator ON Blue (Polarity Optional)

E3JK-R2M2 (red) OFF

White
E3JK-R4M1 L-ON(Ta) ON Tc
E3JK-R4M2 (E3JK-##M1) OFF
Black Contact output
Tb Ta
D-ON(Ta) ON Gray
E3JK-DS30M1 (E3JK-##M2) OFF
E3JK-DS30M2 Built-in relay: G6C

DC transistor output
Model Timing chart Output circuit

24 to 240 VAC
12 to 240 VDC
Brown
Power
source

Incident
E3JK-5S3 Blue
Interrupted
Light ON
E3JK-R2S3 indicator
(red) OFF White
E3JK-R4S3 ON
L-ON mode Drive
OFF
E3JK-DS30S3 circuit Black (L-ON)
ON
D-ON mode Load
OFF Main
circuit
Drive
circuit Gray (D-ON)
Load

24 to 240 VAC
12 to 240 VDC
Brown
Power
source
(Polarity
Optional)
Blue
Incident
Interrupted
Light D/ON
ON Load
indicator Drive
OFF Gray I1
E3JK-R2R3 (red) circuit
ON
L-ON mode L/ON
OFF 48 VDC max.
Load
Drive
ON Main circuit
Black I2
D-ON mode circuit
OFF
I1 + I2 < 100 mA
White

Note: The output stage leakage currents are 0.1 mA max., respectively.

Note: Connect to brown and blue on the emitter side.

E3JK A-223
Operation
Adjustment
Item
Through-beam Retroreflective Models Diffuse-reflective
Model

With sensing object Without sensing object Setting

Background
object
Operation (A) (A) (C)Reset (A)
(C)

(B) Operation
Like the through-beam model, ad-
Swing the receiver and emitter ver- MIN MAX MIN MAX MIN MAX
just the reflector and emitter/re- Sensitivity Sensitivity Sensitivity
tically and/or horizontally and set
ceiver. Since the directional angle
E3JK the adjuster in the center of the
of the emitter/receiver is 1 to 5°, ad- (1) If you have a sensing object as shown in the figure, turn the sensitivity
range where the indicator of the re- adjuster clockwise (increase the sensitivity) until the indicator is turned
just the emitter/receiver especially
ceiver turns ON. ON, and define this adjuster position as (A).
carefully.
(2) Remove the sensing object, turn the sensitivity adjuster clockwise until
the indicator is turned ON by a background object, and define this posi-
tion as (B).
(3) Turn the sensitivity adjuster counterclockwise (decrease the sensitivity)
from (B) until the indicator is turned OFF, and define this position as (C).
(4) The position in the middle of (A) and (C) is the optimum position. If the
indicator is not turned ON by the background object at the maximum
sensitivity, set the adjuster in the middle of (A) and maximum sensitivity.
∑ The sensitivity adjuster may be damaged if an excessive force is applied.

Precautions
Correct Use

Miscellaneous
E3JK
Ambient Conditions (Installation Area)
Design
The E3JK will malfunction if installed in the following places.
Power Reset Time
• Places where the E3JK is exposed to a dusty environment.
The Sensor is ready to detect an object within 200 ms after it
• Places where corrosive gases are produced.
is turned ON. If Sensor and load are connected to separate
power supplies, ensure to turn ON the Sensor first.

Wiring Considerations
Connection/Wiring
Emitter
If the DC transistor output type is used, the sum of load cur- Receiver

rents of L-ON output (NO) and D-ON output (NC) should be

within 100 mA. If the sum of load currents exceeds 100 mA,
• Places where the E3JK is directly exposed to water, oil, or
the load short-circuit protection may be activated. (The load
chemicals.
short-circuit protection is reset by turning OFF the power of
the photoelectric sensor.)

Emitter
Receiver

A-224 Photoelectric Sensors

Dimensions (Unit: mm)
Sensors
E3JK-5## CAD file E3JK_01 E3JK-R2## CAD file E3JK_02
E3JK-R4##

E3JK
E3JK-DS30##
With Mounting Bracket Attached v

6-dia., 5-conductor, vinyl-insulated

round cable (conductor cross-sectional With Mounting Bracket Attached
area: 0.3 mm²; insulation diameter: 1.5 mm). 6-dia., 5-conductor, vinyl-insulated round cable
Standard length: 2 m. * 3 (conductor cross-sectional area: 0.3 mm²; insulation diameter: 1.5 mm).
Standard length: 2 m. * 3
Sensitivity adjustment
volume * 2

40 21
12 40 21
22 12 12
22 12

Emitter: E3JK-5L 6.4 6.4

6 dia. 6.4 6 dia. 6.4
Receiver: E3JK-5D## 4 9 18
4 9 18
42 7
42 7 18 Light indicator 50
18 Indicator *2 ( A ) * 1 13.4 Lens 5
50 40
(A)*1
13.4
Lens 14.8 dia. 40 5
Emitter Optical
28

Receiver
50 axis 40
25 60

28 Optical 40 R56.6
50 axis 40
60 10˚
21.5
36.5 R56.6 Mounting Holes Steel 58
2-M6 * 1. Mounting brackets can be used on the A side (Two, M4 x 20 attached) .
10˚ * 2. No sensitivity adjustment volume on the retororeflective model.

Mounting Holes Steel 58 42

2-M6 * 1.Mounting brackets can be used on the A side (Two, M4 x 20 attached) .

* 2.Emitter: Power indicator
Receiver: Light indicator
* 3.Emitter includes 2-conductor.
42

Accessories (Order Separately)

Seal type long slit (for E3JK)
E39-S39
14

1±0.1

20 26.5
Material: Polyester
0.1 mm thick

E3JK A-225