Product Sample & Technical Tools & Support &

Folder Buy Documents Software Community

LMV761, LMV762, LMV762Q-Q1

SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

LMV76x and LMV762Q-Q1 Low-Voltage, Precision Comparator With Push-Pull Output

1 Features 2 Applications
1• VS = 5 V, TA = 25°C, Typical Values Unless • Portable and Battery-Powered Systems
Specified • Scanners
• Input Offset Voltage 0.2 mV • Set-Top Boxes
• Input Offset Voltage (Maximum Over Temp) 1 mV • High-Speed Differential Line Receiver
• Input Bias Current 0.2 pA • Window Comparators
• Propagation Delay (OD = 50 mV) 120 ns • Zero-Crossing Detectors
• Low Supply Current 300 μA • High-Speed Sampling Circuits
• CMRR 100 dB • Automotive
• PSRR 110 dB
• Extended Temperature Range −40°C to +125°C 3 Description
• Push-Pull Output The LMV76x devices are precision comparators
intended for applications requiring low noise and low
• Ideal for 2.7-V and 5-V Single-Supply Applications input offset voltage. The LMV761 single has a
• Available in Space-Saving Packages: shutdown pin that can be used to disable the device
– 6-Pin SOT-23 (Single With Shutdown) and reduce the supply current. The LMV761 is
available in a space-saving 6-pin SOT-23 or 8-Pin
– 8-Pin SOIC (Single With Shutdown)
SOIC package. The LMV762 dual is available in 8-pin
– 8-Pin SOIC and VSSOP (Dual Without SOIC or VSSOP package. The LMV762Q-Q1 is
Shutdown) available VSSOP and SOIC packages.
• LMV762Q-Q1 is Qualified for Automotive These devices feature a CMOS input and push-pull
Applications output stage. The push-pull output stage eliminates
• AEC-Q100 Qualified With the Following Results: the need for an external pullup resistor.
– Device Temperature Grade 1: –40°C to The LMV76x are designed to meet the demands of
+125°C Ambient Operating Temperature small size, low power and high performance required
Range by portable and battery-operated electronics.
– Device HBM ESD Classification Level 1C The input offset voltage has a typical value of 200 μV
– Device CDM ESD Classification Level M2 at room temperature and a 1-mV limit over
temperature.

Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
SOIC (8) 4.90 mm × 3.91 mm
LMV761
SOT-23 (6) 2.90 mm × 1.60 mm
LMV762 SOIC (8) 4.90 mm × 3.91 mm
LMV762Q-Q1 VSSOP (8) 3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.

Threshold Detector VOS vs VCC

VIN 0.2
VCC 125°C
0.18
0.16
R1
C1 = 0.14 25°C
0.1µF 85°C
VOS (mV)

0.12
+ 0.1
VOUT 0.08 -40°C
0.06
R2 -
SD 0.04
0.02
0
VREF 2.5 3 3.5 4 4.5 5
VCC (V)
1

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

Table of Contents
1 Features .................................................................. 1 7.2 Functional Block Diagram ....................................... 11
2 Applications ........................................................... 1 7.3 Feature Description................................................. 11
3 Description ............................................................. 1 7.4 Device Functional Modes........................................ 12
4 Revision History..................................................... 2 8 Application and Implementation ........................ 13
8.1 Application Information............................................ 13
5 Pin Configuration and Functions ......................... 3
8.2 Typical Application ................................................. 13
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4 9 Power Supply Recommendations...................... 15
6.2 ESD Ratings: LMV761, LMV762............................... 5 10 Layout................................................................... 15
6.3 ESD Ratings: LMV762Q-Q1 ..................................... 5 10.1 Layout Guidelines ................................................. 15
6.4 Recommended Operating Conditions....................... 5 10.2 Layout Example .................................................... 15
6.5 Thermal Information .................................................. 5 11 Device and Documentation Support ................. 16
6.6 2.7-V Electrical Characteristics ................................ 5 11.1 Documentation Support ........................................ 16
6.7 5-V Electrical Characteristics ................................... 6 11.2 Community Resources.......................................... 16
6.8 2-V Switching Characteristics ................................... 7 11.3 Trademarks ........................................................... 16
6.9 5-V Switching Characteristics ................................... 7 11.4 Electrostatic Discharge Caution ............................ 16
6.10 Typical Characteristics ............................................ 8 11.5 Glossary ................................................................ 16
7 Detailed Description ............................................ 11 12 Mechanical, Packaging, and Orderable
7.1 Overview ................................................................. 11 Information ........................................................... 16

4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision H (March 2013) to Revision I Page

• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1

Changes from Revision G (March 2013) to Revision H Page

• Changed layout of National Data Sheet to TI format ........................................................................................................... 15

2 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 LMV761, LMV762, LMV762Q-Q1
www.ti.com SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

5 Pin Configuration and Functions

LMV761 (Single) DBV Package

6-Pin SOT-23
Top View

1 6 +
+IN V

- 2 5
V SD

3 4
-IN OUT

Pin Functions for SOT-23

PIN
TYPE DESCRIPTION
NO. NAME
1 +IN I Noninverting input
2 V- P Negative power terminal
3 -IN I Inverting input
4 OUT O Output
5 SDB I Shutdown (active low)
6 V+ P Positive power terminal

LMV761 (Single) D Package

8-Pin SOIC
Top View

1 8
N/C N/C

2 7 +
-IN V

3 6
+IN OUT

- 4 5
V SD

Pin Functions for SOIC (Single)

PIN
TYPE DESCRIPTION
NO. NAME
1 N/C — No Connect (not internally connected)
2 -IN I Inverting Input
3 +IN I Noninverting Input
4 V- P Negative Power Terminal
5 SDB I Shutdown (active low)
6 OUT O Output
+
7 V P Positive Power Terminal
8 N/C — No Connect (not internally connected)

Copyright © 2002–2015, Texas Instruments Incorporated Submit Documentation Feedback 3

Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

LMV762, LMV762Q-Q1 (Dual) DBV or DGK Package

8-Pin SOIC or VSSOP
Top View

1 8 +
OUT A V

2 7
-IN A OUT B

3 6
+IN A -IN B

- 4 5
V +IN B

Pin Functions for SOIC and VSSOP (Dual)

PIN
TYPE DESCRIPTION
NO. NAME
1 OUTA O Channel A Output
2 -INA I Channel A Inverting Input
3 +INA I Channel A Noninverting Input
4 V- P Negative Power Terminal
5 +INB I Channel B Noninverting Input
6 -INB I Channel B Inverting Input
7 OUTB O Channel B Output
8 V+ P Positive Power Terminal

6 Specifications
6.1 Absolute Maximum Ratings
(1) (2)
See
MIN MAX UNIT
Supply voltage (V+ – V−) 5.5 V
Differential input voltage Supply Voltage
Voltage between any two pins Supply Voltage
Output short circuit Current at input pin
±5 mA
duration (3)
Infrared or convection (20 sec.) 235 °C
Soldering information
Wave soldering (10 sec.) (Lead temp) 260 °C
Junction temperature 150 °C
Storage temperature, Tstg −65 150 °C

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output current in excess of ±25 mA over long term may adversely
affect reliability.

4 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 LMV761, LMV762, LMV762Q-Q1
www.ti.com SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

6.2 ESD Ratings: LMV761, LMV762

VALUE UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (2) ± 2000
V(ESD) Electrostatic discharge (1) V
Machine model ± 200

(1) Unless otherwise specified human body model is 1.5 kΩ in series with 100 pF. Machine model 200 pF.
(2) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

6.3 ESD Ratings: LMV762Q-Q1

VALUE UNIT
Human-body model (HBM), per AEC Q100-002 (1) ± 2000
V(ESD) Electrostatic discharge V
Machine model ± 200

(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.

6.4 Recommended Operating Conditions

MIN MAX UNIT
+ −
Supply voltage (V – V ) 2.7 5.25 V
Temperature range −40 125 °C

6.5 Thermal Information

LMV761 LMV762, LMV762Q-Q1
THERMAL METRIC (1) D (SOIC) DBV (SOT-23) DGK (VSSOP) UNIT
8 PINS 6 PINS 8 PINS
(2)
RθJA Junction-to-ambient thermal resistance 190 265 235 °C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
(2) The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) – TA) RθJA. All numbers apply for packages soldered directly into a PCB.

6.6 2.7-V Electrical Characteristics

Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V+ / 2, V+ = 2.7 V, V− = 0 V−.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
0.2
VOS Input offset voltage mV
apply at the temperature extremes (3) 1
IB Input bias current (4) 0.2 50 pA
(4)
IOS Input offset current 0.001 5 pA
Common-mode rejection
CMRR 0 V < VCM < VCC – 1.3 V 80 100 dB
ratio
PSRR Power supply rejection ratio V+ = 2.7 V to 5 V 80 110 dB
Input common-mode voltage apply at the temperature
CMVR CMRR > 50 dB −0.3 1.5 V
range extremes (3)
+ +
Output swing high IL = 2 mA, VID = 200 mV V – 0.35 V – 0.1 V
VO
Output swing low IL = −2 mA, VID = –200 mV 90 250 mV
Sourcing, VO = 1.35 V, VID = 200 mV 6 20
ISC Output short circuit current (5) mA
Sinking, VO = 1.35 V, VID = –200 mV 6 15

(1) All limits are specified by testing or statistical analysis.

(2) Typical values represent the most likely parametric norm.
(3) Maximum temperature ensured range is −40°C to +125°C.
(4) Specified by design.
(5) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. See Recommended Operating Conditions for information on temperature
de-rating of this device. Absolute Maximum Rating indicate junction temperature limits beyond which the device may be permanently
degraded, either mechanically or electrically.
Copyright © 2002–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

2.7-V Electrical Characteristics (continued)

Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V+ / 2, V+ = 2.7 V, V− = 0 V−.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Supply current LMV761
275 700 μA
(single comparator)
IS
LMV762, LMV762Q-Q1 (both 550
μA
comparators) apply at the temperature extremes (3) 1400
IOUT LEAKAGE Output leakage I at shutdown SD = GND, VO = 2.7 V 0.2 μA
Supply leakage I at
IS LEAKAGE SD = GND, VCC = 2.7 V 0.2 2 μA
shutdown

6.7 5-V Electrical Characteristics

Unless otherwise specified, all limited ensured for TJ = 25°C, VCM = V+ / 2, V+ = 5 V, V− = 0 V−.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
0.2
VOS Input offset voltage mV
apply at the temperature extremes (3) 1
IB Input bias current (4) 0.2 50 pA
IOS Input offset current (4) 0.01 5 pA
Common-mode rejection
CMRR 0 V < VCM < VCC – 1.3 V 80 100 dB
ratio
+
PSRR Power supply rejection ratio V = 2.7 V to 5 V 80 110 dB
Input common-mode voltage apply at the temperature
CMVR CMRR > 50 dB −0.3 3.8 V
range extremes (3)
Output swing high IL = 4 mA, VID = 200 mV V+ – 0.35 V+ – 0.1 V
VO
Output swing low IL = –4 mA, VID = –200 mV 120 250 mV
Sourcing, VO = 2.5 V, VID = 200 mV 6 60
ISC Output short circuit current (5) mA
Sinking, VO = 2.5 V, VID = −200 mV 6 40
Supply current LMV761
225 700 μA
(single comparator)
IS
LMV762, LMV762Q-Q1 450
μA
(both comparators) apply at the temperature extremes (3) 1400
Output leakage I at
IOUT LEAKAGE SD = GND, VO = 5 V 0.2 μA
shutdown
Supply leakage I at
IS LEAKAGE SD = GND, VCC = 5 V 0.2 2 μA
shutdown

(1) All limits are specified by testing or statistical analysis.

(2) Typical values represent the most likely parametric norm.
(3) Maximum temperature ensured range is −40°C to +125°C.
(4) Specified by design.
(5) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. See Recommended Operating Conditions for information on temperature
de-rating of this device. Absolute Maximum Rating indicate junction temperature limits beyond which the device may be permanently
degraded, either mechanically or electrically.

6 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 LMV761, LMV762, LMV762Q-Q1
www.ti.com SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

6.8 2-V Switching Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Overdrive = 5 mV 270
Propagation delay
tPD RL = 5.1 kΩ Overdrive = 10 mV 205 ns
CL = 50 pF
Overdrive = 50 mV 120
tSKEW Propagation delay skew 5 ns
tr Output rise time 10% to 90% 1.7 ns
tf Output fall time 90% to 10% 1.8 ns
ton Turnon time from shutdown 6 μs

6.9 5-V Switching Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Overdrive = 5 mV 225
Propagation delay
tPD RL = 5.1 kΩ Overdrive = 10 mV 190 ns
CL = 50 pF
Overdrive = 50 mV 120
tSKEW Propagation delay skew 5 ns
tr Output rise time 10% to 90% 1.7 ns
tf Output fall time 90% to 10% 1.5 ns
ton Turnon time from shutdown 4 μs

Copyright © 2002–2015, Texas Instruments Incorporated Submit Documentation Feedback 7

Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

6.10 Typical Characteristics

0.5 0.5
125°C 0.45 125°C
0.45

SUPPLY CURRENT PER CH (mA)

SUPPLY CURRENT PER CH (mA)

0.4 0.4
85°C 85°C
0.35 0.35

0.3 0.3

0.25 0.25
25°C 25°C
0.2 0.2

0.15 0.15
0.1 -40°C 0.1 -40°C

0.05 0.05

0 0
1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
VCC (V) VCC (V)
VO = High VO = Low
Figure 1. PSI vs VCC Figure 2. PSI vs VCC
0.2 100
125°C
0.18 80 VS = +2.7 V
0.16
INPUT BIAS CURRENT (fA)
60
0.14 25°C 40
85°C
VOS (mV)

0.12 20
0.1 0
0.08 -40°C -20
0.06 -40
0.04 -60
0.02 -80
0 -100
2.5 3 3.5 4 4.5 5 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7
VCC (V) COMMON MODE VOLTAGE (V)

Figure 3. VOS vs VCC Figure 4. Input Bias vs Common Mode at 25°C

100 0.4
IL = 4 mA
VS = +5 V
OUTPUT VOLTAGE, REF TO V (V)

80 0.35
+
INPUT BIAS CURRENT (fA)

60
0.3
40 125°C

20 0.25
85°C
0 0.2
25°C
-20 0.15
-40
0.1
-60
-40°C
-80 0.5

-100 0
0 1 2 3 4 5 2 2.5 3 3.5 4 4.5 5 5.5 6
COMMON MODE VOLTAGE (V) VCC (V)

Figure 5. Input Bias vs Common Mode at 25°C Figure 6. Output Voltage vs Supply Voltage

8 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 LMV761, LMV762, LMV762Q-Q1
www.ti.com SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

Typical Characteristics (continued)

0.16 0.4
IL = 2 mA IL = -4 mA
OUTPUT VOLTAGE, REF TO V (V)

OUTPUT VOLTAGE REF TO V (V)

0.14 0.35
+

125°C 125°C

-
0.12 0.3
85°C 85°C
0.1 0.25
25°C 25°C
0.08 0.2

0.06 0.15

0.04 0.1
-40°C -40°C
0.02 0.05

0 0
2 2.5 3 3.5 4 4.5 5 5.5 6 2 2.5 3 3.5 4 4.5 5 5.5 6
VCC (V) VCC (V)

Figure 7. Output Voltage vs Supply Voltage Figure 8. Output Voltage vs Supply Voltage
0.2 80
IL = -2 mA -40°C VCC = 5 V
0.18
OUTPUT VOLTAGE, TO REF V (V)

70
125°C
-

0.16 25°C
60
0.14 85°C
85°C 50
0.12 ISINK (mA)
25°C
0.1 40

0.08 30 125°C
0.06
20
0.04
-40°C 10
0.02
0 0
2 2.5 3 3.5 4 4.5 5 5.5 6 0 0.5 1 1.5 2 2.5
VCC (V) VOUT (V)

Figure 9. Output Voltage vs Supply Voltage Figure 10. ISOURCE vs VOUT

60 25
-40°C -40°C VCC = 2.7 V
VCC = 5 V
50 25°C 20 25°C

40 85°C
85°C
ISOURCE (mA)

15
ISINK (mA)

30
125°C
10
125°C
20

5
10

0 0
0 0.5 1 1.5 2 2.5 0 0.2 0.4 0.6 0.8 1 1.2 1.4
VOUT (V)
VOUT (V)

Figure 12. ISOURCE vs VOUT

Figure 11. ISINK vs VOUT

Copyright © 2002–2015, Texas Instruments Incorporated Submit Documentation Feedback 9

Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

Typical Characteristics (continued)

20 500
-40°C RL = 5.1 k:
18 450
CL = 50 pF
16 400
25°C
14

PROP DELAY (ns)

350
ISINK (mA)

12 300
2.7 V
10 250
85°C
8 200
125°C 5V
6 150
4 100
2 VCC = 2.7 V 50
0 0
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1 10 100
VOUT (V) OVERDRIVE (mV)

Figure 13. ISINK vs VOUT Figure 14. Prop Delay vs Overdrive

3 6

OUTPUT VOLTAGE
OUTPUT VOLTAGE

VCC = 2.7 V VCC = 5 V

TEMP = 25°C 5 TEMP = 25°C
10 mV 5 mV 10 mV 5 mV
2 LOAD = 5.1 k: 4 LOAD = 5.1 k:

(V)
50 pF 50 pF
(V)

3
1 2
OVERDRIVE =
1 OVERDRIVE =
50 mV
50 mV
0 0
INPUT VOLTAGE

INPUT VOLTAGE

| OVERDRIVE | | OVERDRIVE |
(mV)

0 0
(mV)

-150 -150

0 50 100 150 200 250 300 0 50 100 150 200 250

TIME (ns) TIME (ns)

Figure 15. Response Time vs Input Overdrives Positive Figure 16. Response Time vs Input Overdrives Positive
Transition Transition
3 6
OUTPUT VOLTAGE
OUTPUT VOLTAGE

5
VCC = 2.7 V 10 mV 5 mV VCC = 5 V 10 mV 5 mV
2 TEMP = 25°C 4
TEMP = 25°C
(V)
(V)

LOAD = 5.1 k: 3 LOAD = 5.1 k:

50 pF 50 pF
1 2
OVERDRIVE = 1 OVERDRIVE =
0 50 mV 0 50 mV
INPUT VOLTAGE

INPUT VOLTAGE

| | | |
(mV)

150
(mV)

150

0 0
OVERDRIVE OVERDRIVE
0 50 100 150 200 250 300 0 50 100 150 200 250
TIME (ns) TIME (ns)

Figure 17. Response Time vs Input Overdrives Negative Figure 18. Response Time vs Input Overdrives Negative
Transition Transition

10 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 LMV761, LMV762, LMV762Q-Q1
www.ti.com SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

7 Detailed Description

7.1 Overview
The LMV76x family of precision comparators is available in a variety of packages and is ideal for portable and
battery-operated electronics.
To minimize external components, the LMV76x family features a push-pull output stage where the output levels
are power-supply determined. In addition, the LMV761 (single) features an active-low shutdown pin that can be
used to disable the device and reduce the supply current.

7.2 Functional Block Diagram

+
V

VREF -
VO
VIN
+

-
V

7.3 Feature Description

7.3.1 Basic Comparator
A basic comparator circuit is used to convert analog input signals to digital output signals. The comparator
compares an input voltage (VIN) at the noninverting input to the reference voltage (VREF) at the inverting pin. If
VIN is less than VREF the output (VO) is low (VOL). However, if VIN is greater than VREF, the output voltage (VO) is
high (VOH).
+
V

VREF -
VO
VIN
+

-
V

Figure 19. Basic Comparator Without Hysteresis

Figure 20. Basic Comparator

7.3.2 Hysteresis
The basic comparator configuration may oscillate or produce a noisy output if the applied differential input is near
the input offset voltage of the comparator, which tends to occur when the voltage on one input is equal or very
close to the other input voltage. Adding hysteresis can prevent this problem. Hysteresis creates two switching
thresholds (one for the rising input voltage and the other for the falling input voltage). Hysteresis is the voltage
difference between the two switching thresholds. When both inputs are nearly equal, hysteresis causes one input
to effectively move quickly past the other. Thus, moving the input out of the region in which oscillation may occur.

Copyright © 2002–2015, Texas Instruments Incorporated Submit Documentation Feedback 11

Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

Feature Description (continued)

Hysteresis can easily be added to a comparator in a noninverting configuration with two resistors and positive
feedback Figure 22. The output will switch from low to high when VIN rises up to VIN1, where VIN1 is calculated by
Equation 1:
VIN1 = [VREF(R1 + R2)] / R2 (1)
The output will switch from high to low when VIN falls to VIN2, where VIN2 is calculated by Equation 2:
VIN2 = [VREF(R1 + R2) – (VCC R1)] / R2 (2)
The Hysteresis is the difference between VIN1 and VIN2, as calculated by Equation 3:
ΔVIN = VIN1 – VIN2 = [VREF(R1 + R2) / R2] – [VREF(R1 + R2)] – [(VCC R1) / R2] = VCC R1 / R2 (3)
VCC

VREF -
VO

VIN +
R1

R2

Figure 21. Basic Comparator With Hysteresis

VO

VIN2 VIN1

0 VIN

Figure 22. Noninverting Comparator Configuration

7.3.3 Input
The LMV76x devices have near-zero input bias current, which allows very high resistance circuits to be used
without any concern for matching input resistances. This near-zero input bias also allows the use of very small
capacitors in R-C type timing circuits. This reduces the cost of the capacitors and amount of board space used.

7.4 Device Functional Modes

7.4.1 Shutdown Mode
The LMV761 features a low-power shutdown pin that is activated by driving SD low. In shutdown mode, the
output is in a high-impedance state, supply current is reduced to 20 nA and the comparator is disabled. Driving
SD high will turn the comparator on. The SD pin must not be left unconnected due to the fact that it is a high-
impedance input. When left unconnected, the output will be at an unknown voltage. Do not three-state the SD
pin.
The maximum input voltage for SD is 5.5 V referred to ground and is not limited by VCC. This allows the use of
5-V logic to drive SD while VCC operates at a lower voltage, such as 3 V. The logic threshold limits for SD are
proportional to VCC.

12 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 LMV761, LMV762, LMV762Q-Q1
www.ti.com SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

8 Application and Implementation

NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.

8.1 Application Information

The LMV76x are single-supply comparators with 120 ns of propagation delay and 300 µA of supply current.

8.2 Typical Application

A typical application for a LMV76x comparator is a programmable square-wave oscillator.
R4

C1
-
VC VO

+
R1 VA R3
+
V

+
R2 V

Figure 23. Square-Wave Oscillator

8.2.1 Design Requirements

The circuit in Figure 23 generates a square wave whose period is set by the RC time constant of the capacitor
C1 and resistor R4. V+ = 5 V unless otherwise specified.

8.2.2 Detailed Design Procedure

The maximum frequency is limited by the large signal propagation delay of the comparator and by the capacitive
loading at the output, which limits the output slew rate.

Figure 24. Square-Wave Oscillator Timing Thresholds

Copyright © 2002–2015, Texas Instruments Incorporated Submit Documentation Feedback 13

Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

Typical Application (continued)

Consider the output of Figure 23 is high to analyze the circuit. That implies that the inverted input (VC) is lower
than the noninverting input (VA). This causes the C1 to be charged through R4, and the voltage VC increases until
it is equal to the noninverting input. The value of VA at this point is calculated by Equation 4:
VCC ˜ R2
VA1
R2 R1 R R3 (4)
If R1 = R2 = R3, then VA1 = 2 VCC / 3
At this point the comparator switches pulling down the output to the negative rail. The value of VA at this point is
calculated by Equation 5:
VCC (R2 R R3 )
VA2
R1 (R2 R R3 ) (5)
If R1 = R2 = R3, then VA2 = VCC / 3.
The capacitor C1 now discharges through R4, and the voltage VC decreases until it is equal to VA2, at which point
the comparator switches again, bringing it back to the initial stage. The time period is equal to twice the time it
takes to discharge C1 from 2 VCC / 3 to VCC / 3, which is given by R4C1 × ln2. Hence, the formula for the
frequency is calculated by Equation 6:
F = 1 / (2 × R4 × C1 × ln2) (6)

8.2.3 Application Curve

Figure Figure 25 shows the simulated results of an oscillator using the following values:
• R1 = R2 = R3 = R4 = 100 kΩ
• C1 = 100 pF, CL = 20 pF
• V+ = 5 V, V– = GND
• CSTRAY (not shown) from Va to GND = 10 pF
6
VOUT
5
Va
4
VOUT (V)

1
Vc
0

-1
0 10 20 30 40 50
TIME (µs) C001

Figure 25. Square-Wave Oscillator Output Waveform

14 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 LMV761, LMV762, LMV762Q-Q1
www.ti.com SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015

9 Power Supply Recommendations

To minimize supply noise, power supplies must be decoupled by a 0.1-μF ceramic capacitor in parallel with a
10-μF capacitor.
Due to the nanosecond edges on the output transition, peak supply currents will be drawn during output
transitions. Peak current depends on the capacitive loading on the output. The output transition can cause
transients on poorly bypassed power supplies. These transients can cause a poorly bypassed power supply to
ring due to trace inductance and low self-resonance frequency of high ESR bypass capacitors.
Treat the LMV6x as a high-speed device. Keep the ground paths short and place small (low-ESR ceramic)
bypass capacitors directly between the V+ and V– pins.
Output capacitive loading and output toggle rate will cause the average supply current to rise over the quiescent
current.

10 Layout

10.1 Layout Guidelines

The LMV76x is designed to be stable and oscillation free, but it is still important to include the proper bypass
capacitors and ground pick-ups. Ceramic 0.1-μF capacitors must be placed at both supplies to provide clean
switching. Minimize the length of signal traces to reduce stray capacitance.

10.2 Layout Example

C1

GND

R1
+IN

VIN V+
SOT-23

GND SD

OUT

-IN

VREF

R2
Figure 26. Comparator With Hysteresis

Copyright © 2002–2015, Texas Instruments Incorporated Submit Documentation Feedback 15

Product Folder Links: LMV761 LMV762 LMV762Q-Q1
LMV761, LMV762, LMV762Q-Q1
SNOS998I – FEBRUARY 2002 – REVISED OCTOBER 2015 www.ti.com

11 Device and Documentation Support

11.1 Documentation Support

11.1.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.

Table 1. Related Links

TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY
DOCUMENTS SOFTWARE COMMUNITY
LMV761 Click here Click here Click here Click here Click here
LMV762 Click here Click here Click here Click here Click here
LMV762Q-Q1 Click here Click here Click here Click here Click here

11.2 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.

11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.

11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

16 Submit Documentation Feedback Copyright © 2002–2015, Texas Instruments Incorporated

Product Folder Links: LMV761 LMV762 LMV762Q-Q1

 PACKAGE OPTION ADDENDUM

www.ti.com 27-Sep-2017

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

LMV761MA NRND SOIC D 8 95 TBD Call TI Call TI -40 to 125 LMV76

1MA
LMV761MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LMV76
& no Sb/Br) 1MA
LMV761MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LMV76
& no Sb/Br) 1MA
LMV761MF NRND SOT-23 DBV 6 1000 TBD Call TI Call TI -40 to 125 C22A
LMV761MF/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 C22A
& no Sb/Br)
LMV761MFX NRND SOT-23 DBV 6 3000 TBD Call TI Call TI -40 to 125 C22A
LMV761MFX/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 C22A
& no Sb/Br)
LMV762MA NRND SOIC D 8 95 TBD Call TI Call TI -40 to 125 LMV7
62MA
LMV762MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LMV7
& no Sb/Br) 62MA
LMV762MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LMV7
& no Sb/Br) 62MA
LMV762MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 C23A
& no Sb/Br)
LMV762MMX NRND VSSOP DGK 8 3500 TBD Call TI Call TI -40 to 125 C23A
LMV762MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 C23A
& no Sb/Br)
LMV762QMA/NOPB ACTIVE SOIC D 8 95 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LMV76
& no Sb/Br) 2QMA
LMV762QMAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LMV76
& no Sb/Br) 2QMA
LMV762QMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 C32A
& no Sb/Br)
LMV762QMMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 C32A
& no Sb/Br)

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 27-Sep-2017

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 24-Aug-2017

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMV761MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LMV761MF SOT-23 DBV 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LMV761MF/NOPB SOT-23 DBV 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LMV761MFX SOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LMV761MFX/NOPB SOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LMV762MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LMV762MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LMV762MMX VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LMV762MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LMV762QMAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LMV762QMM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LMV762QMMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 24-Aug-2017

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LMV761MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0
LMV761MF SOT-23 DBV 6 1000 210.0 185.0 35.0
LMV761MF/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0
LMV761MFX SOT-23 DBV 6 3000 210.0 185.0 35.0
LMV761MFX/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0
LMV762MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0
LMV762MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LMV762MMX VSSOP DGK 8 3500 367.0 367.0 35.0
LMV762MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
LMV762QMAX/NOPB SOIC D 8 2500 367.0 367.0 35.0
LMV762QMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LMV762QMMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0

Pack Materials-Page 2
 IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated