Qty. Item No.
FT-800 SERIES
FOOD EQUIPMENT
DISHWASHER
FT-800 SERIES • Water and energy saving • Wash arms easily installed and
design through reduced water removed without tools.
DISHWASHER WITH
and tank heat usage and
ELECTRO- automatic pump shut down
• All function components
(motors, drains, etc.) located
MECHANICAL control through conveyor.
on operators side of dish-
CONTROLS • Common water, drain, electric machine for accessibility and
and steam connections. ease of maintenance.
OUTSTANDING
STANDARD FEATURES • Exclusive load end flush • Built-in integral prewash water
system. replenishment system.
• Energy saving low water
consumption design—5.7 GPM • Built-in integral wiring channel. • Final rinse actuator.
Hot Water (180°F); 3.9 GPM
• Automatic temperature control • Removable self-flushing stain-
Low Temp (140°F).
and positive low-water heater less steel strainer pans and
• Stainless steel construction and pump seal protection. large deep scrap buckets for
including frame, legs, feet, drain each tank.
• Built-in inherent motor overload
piping, wash arms.
protection with manual reset. • Door interlocks on all doors.
• Electro-mechanical controls in
• Built-in vent ducts—dampers • Optional energy saving blower-
top mounted stainless steel
and drip control. dryer.
control center.
• Improved washability with high Electric 20 KW—63% energy
• 36" Load/Unload height.
pressure prewash—wash and reduction.
• Energy efficient convertible hot power rinse systems.
Steam 75 lbs./hr.—56%
water or low temp/chemical
• Compct modular design. energy reduction.
sanitizing.
• 115 volt pilot circuit. • Choice of electric, steam
• Door actuated drain closers.
injection or steam coil heat.
• Lower prewash arm.
• Sealed dial type thermometers Specifications, Details, Dimensions and
for wash—power rinse—final • Automatic initial fill. Connections inside.
rinse—temperature indication.
FT-800 SERIES
DISHWASHER FOOD EQUIPMENT
STANDARD DESIGN FEATURES
TOP MOUNTED CONTROL PANEL – WASH ARMS – Computer-designed prewash,
Controls in top-mounted stainless steel control wash and power rinse arms. Arms designed so
center with master On/Off Power Switch. they can be installed only in correct position.
STOP/START PUSH BUTTONS – Recessed, side located waterproof Start/Stop push FLUSH DOWN –
buttons and flip-up hinged dishware platform on both ends of dishwasher. Exclusive load end
flush down system.
DRAIN CLOSERS – Door operated drain PUMP – Self-draining Hobart pump motors
closers . . . front located drains, stainless steel with inherent motor protection and manual
tank overflow tubing to prewash, and final overload reset push buttons on each motor.
rinse water feed piping.
Qty. Item No.
FT-800 SERIES
FOOD EQUIPMENT
DISHWASHER
WIRING CHANNEL – Built-in integral wireway above tank water level.
SCRAP PANS – Large one-piece sloped VENT DUCTS – Built-in vent ducts with
scrap screens and deep removable recessed adjustable dampers and drip shield on each
scrap buckets for prewash, wash and power end of dishwasher. 2" x 24" load end and
rinse tanks. 4" x 24" discharge end (inside dimensions).
POSITIVE LOW WATER PROTECTION –
Solid state positive low water protection for
tank heaters.
FT-800 SERIES
DISHWASHER FOOD EQUIPMENT
DETAILS, DIMENSIONS AND CONNECTIONS RIGHT TO LEFT OPERATION
Qty. Item No.
FT-800 SERIES
FOOD EQUIPMENT
DISHWASHER
701 RIDGE AVENUE
TROY, OHIO 45374-0001
FT-800 SERIES
DISHWASHER FOOD EQUIPMENT
DETAILS, DIMENSIONS AND CONNECTIONS LEFT TO RIGHT OPERATION
Qty. Item No.
FT-800 SERIES
FOOD EQUIPMENT
DISHWASHER
701 RIDGE AVENUE
TROY, OHIO 45374-0001
FT-800 SERIES
DISHWASHER FOOD EQUIPMENT
SPECIFICATIONS Listed by Underwriters Laboratories Inc. and National Sanitation Foundation.
Meets Requirements of A.S.S.E. Standard No. 1004.
DESIGN: Fully automatic, flight-type dishwasher nozzles with large openings arranged to STANDARD EQUIPMENT: Automatic initial
machine, consisting of a 5' x 7' loading section effectively remove soil from all types of ware. fill, prewash flushing. Final rinse saver. Sealed
with power recirculating prewash, an 8' power Prewash flushdown is supplied as standard. dial-type thermometers indicate water
wash, power rinse and fresh water final rinse Large removable one-piece perforated temperature in Power Wash, Power Rinse and
section, and a 5', 7', 9' or 11' drying and stainless steel screen sloped downward to Final Rinse. Positive low water protection for
unloading section. Recirculating water prewash, deep perforated stainless steel basket. Baskets tank heat. Plastic strip curtains throughout
power wash, power rinse, and final rinse and screens are removable from front of machine. Stainless steel control panel. 115 volt
compartments constructed with splash baffles machine. pilot circuit. Inspection door interlocks which
and flexible plastic strip curtains for effective prevent pump/conveyor operation when
control and separation of spray systems. Specify DRAIN AND OVERFLOW: Prewash tank inspection door on prewash, wash or rinse
high or low temperature operation. equipped with bell type overflow and drain chambers is open. Built-in wireway. Drains are
valve. Closing the inspection door will automatically closed when inspection doors
CONSTRUCTION: Tank and chambers are automatically close the drain valve. are closed. Stainless steel framing members,
heavy gauge stainless steel with No. 3 polish legs and adjustable feet. Common drain to
on appearance surfaces. Stainless steel POWER WASH AND POWER RINSE: Power
wash and power rinse tanks are equipped with load end. Common water connection. Common
frames, legs, and feet are standard. Three large steam connection for tank heat and optional
inspection doors with welded handles. upper and lower stainless steel wash arms
with specially-shaped nozzles having large booster on steam heated machine. Common
PUMPS: Recirculating pumps with Ni-Resist openings and arranged to effectively direct electric connection for motors and controls.
impellers and face seal with stainless steel water jets to all ware surfaces. Wash arms are OPTIONAL EQUIPMENT AT EXTRA COST—
metal parts and ceramic seat. Readily easily removable without use of tools. Large MECHANICAL: Stainless steel hang-on/
removable motor-impeller assembly permits one-piece removable perforated stainless steel drop-in-place front and rear panels. Energy-
quick inspection. All pumps are self-draining. screen sloped downward to deep perforated saving Blower-Dryer: Electric or steam heated.
stainless steel baskets. Baskets and screens Common drain to unload end. Modified
MOTORS: Hobart-built, grease-packed ball removable from front of machine.
bearings, splashproof design, ventilated with conveyor for insulated trays.
inherent overload protection in each motor. DRAIN AND OVERFLOW: Power wash and OPTIONAL EQUIPMENT AT EXTRA COST—
Recirculating prewash unit 2 H.P., power wash power rinse overflow system directs water TANK HEATING: Regulated stainless steel
and power rinse 3 H.P. each, conveyor 1⁄2 H.P. through internal connecting stainless steel 3
⁄4" steam injectors in power wash and power
Available in electrical specifications of tubing to prewash section. Drain valve is rinse tanks. Stainless steel steam coils.
200-230/60/3 and 460/60/3 with manual reset. controlled from front of machine and is Regulated electric immersion heaters.
automatically closed by closing inspection door.
CONTROLS: A stainless steel control center OPTIONAL EQUIPMENT AT EXTRA COST—
with Power “On/Off” switch is mounted on top of TANK HEATING: Power Wash tank and Power BOOSTERS: Steam heat exchanger with
the center section. Controls use 115 volt pilot Rinse tank water temperatures are each electric thermostatic control, basket type trap,
circuit. Recessed “Start/Stop” controls at each thermostatically controlled. The tank heat with pressure relief valves for both water and steam,
end of machine in stainless steel enclosure, positive low water protection is automatically pressure reducing valve and pressure gauge
factory wired. Electrical components are activated when the Power switch is turned “On.” for incoming water. Booster amply sized to raise
completely wired with 105°C, 600V thermo- If the tank is accidentally drained, the low water 120°F inlet water to 180°F with minimum of 20
plastic insulated wire with stranded conductors protection device automatically turns the tank PSI flowing steam pressure (or 140°F inlet
routed through covered wireway built into the heat off. Select one of the optional heats listed water to 180°F with minimum of 10 PSI flowing
front of the machine above tank water level and under Optional Equipment—Tank Heating. steam). Maximum steam pressure is 50 PSI.
UL Listed electrical metallic tubing or liquid-tight
FINAL RINSE: Upper rinse arm has two rows of Electric booster adequately sized to raise
flexible metal conduit. Locking style electrical
nozzles above and lower arm has one row of 140°F inlet water to 180°F. Pressure/tempera-
connectors are used for connections between
nozzles below dishware. Final rinse water line is ture relief valve, pressure reducing valve and
machine sections. As an energy saving control
equipped with vacuum breaker on downstream pressure gauge for incoming water.
feature, operation of pumps, final rinse and
side of solenoid valve. Design provides for
optional blower-dryer stop when conveyor stops.
collection and division of final rinse water after OPTIONAL EQUIPMENT AT EXTRA COST—
FLIGHT TYPE CONVEYOR: Stainless steel use to power wash tank and power rinse tank. CHEMICAL SANITIZING: Chemical injection
side links, and tie rods and conveyor tracks. Sanitizer and rinse agent dispenser injection pump for low temperature operation.
Injection molded, resilient Duraflex flight links to ports provided in final rinse piping above rinse
chamber. Final rinse water saver “Rinse Gate” OPTIONAL EQUIPMENT AT EXTRA COST—
accommodate flatware and trays in preferred
supplied as standard energy saving feature. ELECTRICAL: Prewash thermometer.
inclined position.
Machine (line) voltage, fuse protected terminal As continued product improvement is a policy of Hobart,
VAPOR CONTROL: Built in vent ducts with provision for detergent and rinse agent specifications are subject to change without notice.
dampers and drip shields located on both dispensers.
ends of machine. Load end duct connection is
2" x 24" inside. Unload end duct connection is CONVEYOR DRIVE UNIT: Powered by a
4" x 24" inside. Hobart-built, inherent overload protected
1
⁄2 H.P. grease packed ball bearing motor. Trip
RECIRCULATING PREWASH SECTION: mechanism provided on unloading end of
Removes soil by means of recirculated water conveyor. Jam protection is provided by load
sprayed over dishes before they enter the power sensing switch at drive platform. These devices
wash zone. The unit receives its water from two interrupt operation of the conveyor motor which
sources. The design provides for receiving all stops the conveyor, pumps and final rinse
detergent overflow water from the wash tank flow. Operation is restarted automatically by
and all the rinse tank overflow. Prewash removing item which has actuated the trip
compartment is fitted with stainless steel upper mechanism, or by operator switch if shutdown
and lower wash arms having specially shaped resulted from other cause.
701 RIDGE AVENUE
TROY, OHIO 45374-0001
FORM F-7964 (REV. 1092) LITHO IN U.S.A. (H-01)
Printed On Recycled Paper
