3000 Series Indicators

Instruction Manual

T31P Indicator

T31XW Indicator

i
ii
Compliance to the following standards is indicated by the corresponding marking on the product.

Marking Standard

This product conforms to the EMC Directive 89/336/EEC, the Low Voltage Directive 73/23/EEC
and the Non-automatic Weighing Instruments Directive 90/384/EEC. The complete Declaration of
Conformity is available from Ohaus Corporation.

AS/NZS4251.1, AS/NZS4252.1

Important Notice for verified weighing instruments

Weighing Instruments verified at the place of manufacture bear one of the preceding marks on the pack-
ing label and the green ‘M’ (metrology) sticker on the descriptive plate. They may be put into service
immediately.

Weighing Instruments to be verified in two stages have no green ‘M’ (metrology) on the descriptive plate
and bear one of the preceding identification mark on the packing label. The second stage of the initial
verification must be carried out by the approved service organization of the authorized representative
within the EC or by the national weights & measures (W+M) authorities.

The first stage of the initial verification has been carried out at the manufacturer’s work. It comprises all tests according to the
adopted European standard EN 45501:1992, paragraph 8.2.2.

If national regulations limit the validity period of the verification, the user of the weighing instrument must strictly observe the
re-verification period and inform the respective W+M authorities.

iii
 Disposal
In conformance with the European Directive 2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE) this device may not be disposed of in domestic waste. This also applies to countries outside
the EU, per their specific requirements.

Please dispose of this product in accordance with local regulations at the collecting point specified for
electrical and electronic equipment.

If you have any questions, please contact the responsible authority or the distributor from which you
purchased this device.

Should this device be passed on to other parties (for private or professional use), the content of this
regulation must also be related.

Thank you for your contribution to environmental protection.

FCC Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

Industry Canada Note

This Class A digital apparatus complies with the Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la Norme NMB-003 du Canada.

ISO 9001 Registration

In 1994, Ohaus Corporation, USA, was awarded a certificate of registration to ISO 9001 by Bureau Veritus Quality International
(BVQI), confirming that the Ohaus quality management system is compliant with the ISO 9001 standard’s requirements. On May
15, 2003, Ohaus Corporation, USA, was re-registered to the ISO 9001:2000 standard.

iv
3000 Series Indicators EN-1
TABLE OF CONTENTS
1. INTRODUCTION..........................................................................................................................................EN-4
1.1 Safety Precautions .....................................................................................................................................EN-4
1.2 Overview of Parts and Controls ...................................................................................................................EN-5
1.3 Control Functions .......................................................................................................................................EN-9

2. INSTALLATION .........................................................................................................................................EN-10
2.1 Unpacking ..............................................................................................................................................EN-10
2.2 External Connections ................................................................................................................................EN-10
2.2.1 RS232 Interface Cable to T31P........................................................................................................EN-10
2.2.2 AC Power to T31P ........................................................................................................................EN-10
2.2.3 AC Power to T31XW .......................................................................................................................EN-10
2.2.4 Battery power (T31P) .....................................................................................................................EN-11
2.2.5 Mounting Bracket to T31XW ............................................................................................................EN-11
2.3 Internal Connections.................................................................................................................................EN-11
2.3.1 Opening the Housing.......................................................................................................................EN-11
2.3.2 Scale Base to T31P or T31XW .......................................................................................................EN-12
2.3.3 RS232 Interface Cable to T31XW ......................................................................................................EN-12
2.4 T31P Rear Cover Orientation .....................................................................................................................EN-13
2.5 Direct Wall Mounting (T31P only) .............................................................................................................EN-13
2.6 Mounting Bracket (T31XW only)................................................................................................................EN-13

3. SETTINGS................................................................................................................................................EN-14
3.1 Menu Structure ........................................................................................................................................EN-14
3.2 Menu Navigation .....................................................................................................................................EN-15
3.3 Calibration Menu .....................................................................................................................................EN-15
3.3.1 Span Calibration ...........................................................................................................................EN-16
3.3.2 Linearity Calibration ......................................................................................................................EN-16
3.3.3 Geographical Adjustment Factor .....................................................................................................EN-17
3.3.4 End Calibration .............................................................................................................................EN-17
3.4 Setup Menu .............................................................................................................................................EN-19
3.4.1 Reset ...........................................................................................................................................EN-19
3.4.2 Legal for trade ..............................................................................................................................EN-19
3.4.3 Calibration Unit .............................................................................................................................EN-19
3.4.4 Capacity ......................................................................................................................................EN-19
3.4.5 Graduation ...................................................................................................................................EN-21
3.4.6 Power On Unit ..............................................................................................................................EN-21
3.4.7 Zero Range ..................................................................................................................................EN-21
3.4.8 End Setup ....................................................................................................................................EN-21
EN-2 3000 Series Indicators

TABLE OF CONTENTS (Cont.)

3.5 Readout Menu .........................................................................................................................................EN-21
3.5.1 Reset ...........................................................................................................................................EN-21
3.5.2 Filter ............................................................................................................................................EN-22
3.5.3 Auto-Zero Tracking ........................................................................................................................EN-22
3.5.4 Backlight .....................................................................................................................................EN-22
3.5.5 Auto Off Timer ..............................................................................................................................EN-22
3.5.6 End Readout .................................................................................................................................EN-22
3.6 Mode Menu .............................................................................................................................................EN-23
3.6.1 Reset ...........................................................................................................................................EN-23
3.6.2 Parts Counting Mode .....................................................................................................................EN-23
3.6.3 End Mode ....................................................................................................................................EN-23
3.7 Unit Menu ...............................................................................................................................................EN-24
3.7.1 Reset ...........................................................................................................................................EN-24
3.7.2 Kilogram Unit ...............................................................................................................................EN-24
3.7.3 Pound Unit ...................................................................................................................................EN-24
3.7.4 Gram Unit ....................................................................................................................................EN-24
3.7.5 Ounce Unit ...................................................................................................................................EN-24
3.7.6 Pound Ounce Unit .........................................................................................................................EN-24
3.7.7 End Unit ......................................................................................................................................EN-24
3.8 Print Menu ..........................................................................................................................................EN-25
3.8.1 Reset ...........................................................................................................................................EN-25
3.8.2 Baud ...........................................................................................................................................EN-25
3.8.3 Parity ..........................................................................................................................................EN-25
3.8.4 Stop Bit .......................................................................................................................................EN-25
3.8.5 Handshake ..................................................................................................................................EN-26
3.8.6 Print Stable Data Only ...................................................................................................................EN-26
3.8.7 Auto Print .....................................................................................................................................EN-26
3.8.8 Content ........................................................................................................................................EN-26
3.8.9 End Print .....................................................................................................................................EN-26
3.9 Menu Lock Menu .....................................................................................................................................EN-27
3.9.1 Reset ...........................................................................................................................................EN-27
3.9.2 Lock Calibration ...........................................................................................................................EN-27
3.9.3 Lock Setup ...................................................................................................................................EN-27
3.9.4 Lock Readout ...............................................................................................................................EN-27
3.9.5 Lock Mode ...................................................................................................................................EN-27
3.9.6 Lock Unit .....................................................................................................................................EN-27
3.9.7 Lock Print ...................................................................................................................................EN-28
3.9.8 End Lock .....................................................................................................................................EN-28
3000 Series Indicators EN-3

TABLE OF CONTENTS (Cont.)

3.10 Security Switch .......................................................................................................................................EN-28
4. OPERATION .............................................................................................................................................EN-28
4.1 Turning Indicator On/Off ............................................................................................................................EN-28
4.2 Zero Operation .........................................................................................................................................EN-28
4.3 Manual Tare ............................................................................................................................................EN-28
4.4 Changing Units of Measure .......................................................................................................................EN-29
4.5 Printing Data ...........................................................................................................................................EN-29
4.6 Application Modes ...................................................................................................................................EN-29
4.6.1 Weighing .....................................................................................................................................EN-29
4.6.2 Parts Counting .............................................................................................................................EN-29

5. SERIAL COMMUNICATION..........................................................................................................................EN-31
5.1 Interface Commands ................................................................................................................................EN-31
5.2 Output Format .........................................................................................................................................EN-32

6. LEGAL FOR TRADE ...................................................................................................................................EN-33

6.1 Settings ..................................................................................................................................................EN-33
6.2 Verification ..............................................................................................................................................EN-33
6.3 Sealing ...................................................................................................................................................EN-33

7. MAINTENANCE.........................................................................................................................................EN-34
7.1 Model T31P Cleaning ...............................................................................................................................EN-34
7.2 Model T31XW Cleaning ............................................................................................................................EN-34
7.3 Troubleshooting .......................................................................................................................................EN-34
7.4 Service Information ..................................................................................................................................EN-35

8. TECHNICAL DATA .....................................................................................................................................EN-36

8.1 Specifications ..........................................................................................................................................EN-36
8.2 Accessories and Options...........................................................................................................................EN-37
8.3 Drawings and Dimensions ........................................................................................................................EN-38
EN-4 3000 Series Indicators

1. INTRODUCTION
This manual contains installation, operation and maintenance instructions for the T31P and T31XW Indicators. Please read this
manual completely before installation and operation.

1.1 Safety Precautions

For safe and dependable operation of this equipment, please comply with the following safety precautions:

• Verify that the input voltage range printed on the data label matches the local AC power to be used.
• Make sure that the power cord does not pose a potential obstacle or tripping hazard.
• Use only approved accessories and peripherals.
• Operate the equipment only under ambient conditions specified in these instructions.
• Disconnect the equipment from the power supply before cleaning.
• Do not operate the equipment in hazardous or unstable environments.
• Do not immerse the equipment in water or other liquids.
• Service should only be performed by authorized personnel.
• The T31XW is supplied with a grounded power cable. Use only with a compatible grounded power outlet.
3000 Series Indicators EN-5

1.2 Overview of Parts and Controls

TABLE 1-1. T31P PARTS.

2 Item Description
1 Data Label
2 Front Housing
3 Control Panel
4 Security Screw
1 5 Key Hole (4) for wall
3
mounting
6 Screw (4)
7 Data Label
8 Rear Housing
9 Power Receptacle
10 Strain Relief for Load Cell
4 Cable

5 11 RS232 Connector

6
7

9 10 11
Figure 1-1. T31P Indicator.
EN-6 3000 Series Indicators

1.2 Overview of Parts and Controls (Cont.)

1 TABLE 1-2. T31XW PARTS.

Item Description
1 Data Label
2 2 Front Housing
3 Adjusting Knob (2)
4 Control Panel
3
5 Mounting Bracket
4 6 Screw (4)
7 Rear Housing
5
8 Data Label
9 Strain Relief for RS232
10 Strain Relief for Load Cell
Cable
11 Power cord

9 10 11

Figure 1-2. T31XW Indicator.

3000 Series Indicators EN-7

1.2 Overview of Parts and Controls (Cont.)

J4 OFF ON
9

J5

J7 J6
W1 W2

1 2 3 4 5 6 7 8

Figure 1-3. Main PC Board.

TABLE 1-3. MAIN PC BOARD.

Item Description
LOAD CELL WIRING 1 Keypad Connector J4 T31XW Model only
2 Battery Connector (T31P only)
3 Line Power Input
4 Sense Jumper W1
5 Load Cell Terminal Block J5
+EXC +SIG -SIG -EXC 6 Sense Jumper W2
+SENS GND -SENS
7 RS232 Terminal Block J7 T31XW Model only
8 RS232 Connector J6 T31P Model only
9 LFT On / Off Switch

RS232 WIRING

TXD GND
RXD
EN-8 3000 Series Indicators

1.2 Overview of Parts and Controls (Cont.)

14
2
3
4

13 12 11 10 9 8 7 6 5

Figure 1-4. Controls and Indicators.

TABLE 1-4. CONTROL PANEL.

No. Designation
1 Capacity Label Window
2 Pound symbol
3 Ounce symbol
4 Kilogram, gram symbols
5 TARE Menu button
6 TARE function symbol
7 FUNCTION Mode button
8 NET function symbol
9 PCS function symbol
10 PRINT Units button
11 Battery function symbol
(T31P only)
12 ON/ZERO Off button
13 Center of Zero Indicator
3000 Series Indicators EN-9

1.3 Control Functions

TABLE 1-5. CONTROL FUNCTIONS.

Button

Primary Function ON/ZERO PRINT FUNCTION TARE

(Short Press) If Indicator is On, sets Sends the current value Initiates an application Performs a tare
zero. to the COM port if mode. operation.
AUTOPRINT is set to Off.

Secondary Function Off Units Mode Menu

(Long Press) Turns the Indicator on Changes the weighing Allows changing the Enter the User menu.
or off. Unit. application mode.

Press and hold allows

scrolling through modes.
Menu Function Yes No Back Exit
(Short Press) Accepts the current Advances to the next Moves Back to previous Exits the User menu.
setting on the display. menu or menu item. menu item.
Aborts the calibration in
Rejects the current Decrements the value. progress.
setting on the display
and advances to the
next available setting.

Increments the value.

EN-10 3000 Series Indicators

2. INSTALLATION
2.1 Unpacking
Unpack the following items:
• T31P or T31XW Indicator
• AC Adapter (T31P only)
• Mounting Bracket (supplied with T31XW only)
• Knobs (2) (supplied with T31XW only)
• Capacity Label Sheet
• Instruction Manual CD
• Warranty Card
• LFT sealing Kit

2.2 External Connections

2.2.1 RS232 interface Cable to T31P

Connect the optional RS232 cable to the RS232 connector Figure 1-1, item 13).

Pin Connection
1 N/C
2 TXD
3 RXD
5 4 3 2 1
4 N/C
9 8 7 6
5 GND
6 N/C Figure 2-1. RS232 Pins.
7 N/C
8 N/C
9 N/C

2.2.2 AC Power to T31P

Connect the AC Adapter to the power receptacle (Figure 1-1, item 8), then plug the AC Adapter into an electrical outlet.

2.2.3 AC Power to T31XW

Connect the AC plug to a properly grounded electrical outlet.
3000 Series Indicators EN-11

2.2.4 Battery Power (T31P Only)

The indicator can be operated on the internal rechargeable battery when AC power is not available. The indicator will
automatically switch to battery operation if there is a power failure or the power cord is removed.

Note:
Before using the indicator for the first time, the internal rechargeable battery should be fully charged for up to
12 hours. The indicator can be operated during the charging process. The battery is protected against over
charging and the indicator can remain connected to the AC power line.

Connect AC power to the indicator and allow it to charge. While the battery is charging, the triangle above the battery function
symbol will light. When the battery is fully charged, this triangle will disappear.

The indicator can operate for up to 100 hours on a fully charged battery.

During battery operation, a flashing triangle above the battery function symbol indicates the battery is low and requires
recharging. Approximately 60 minutes of operation will remain when the battery symbol starts to blink. The indicator will
display Lo.BAT and automatically turn off when the battery is fully discharged.

CAUTION
BATTERY IS TO BE REPLACED ONLY BY AN AUTHORIZED OHAUS
SERVICE DEALER.

RISK OF EXPLOSION CAN OCCUR IF REPLACED WITH THE

WRONG TYPE OR CONNECTED IMPROPERLY.

Dispose of the lead acid battery according to local laws and regulations.

2.2.5 Mounting Bracket to T31XW

Align the mounting bracket over the threaded holes in the side of the indicator and install the knobs. Adjust the indicator to the
desired angle and tighten the knobs.

2.3 Internal Connections

Some connections require the housing to be opened.

2.3.1 Opening the Housing

CAUTION: ELECTRICAL SHOCK HAZARD. REMOVE ALL POWER CONNECTIONS TO THE INDICATOR
BEFORE SERVICING OR MAKING INTERNAL CONNECTIONS. THE HOUSING SHOULD ONLY BE OPENED
BY AUTHORIZED AND QUALIFIED PERSONNEL, SUCH AS AN ELECTRICAL TECHNICIAN.
EN-12 3000 Series Indicators

T31P
Remove the four Phillips head screws from the rear housing.
Open the housing being careful not to disturb the internal connections.
Once all connections are made, reattach the front housing.

T31XW
Remove the four hex head screws from the rear housing.
Open the housing by carefully pulling the top of the front housing forward.
Once all connections are made, reattach the front housing.
The screws should be tightened fully to maintain a watertight seal.

2.3.2 Scale Base to T31P or T31XW

Pass the load cell cable through the strain relief (Figure 1-1, item 9 or Figure 1-2,
item 10) and attach it to terminal block J5 (Figure 1-3, item 5). Pin Connection
Re-tighten the strain relief to ensure a watertight seal. J5-1 +EXCITATION
J5-2 +SENSE
Jumper Connections J5-3 +SIGNAL
For a 4-wire load cell with no sense wires: Jumpers W2 and W3 must be shorted.
J5-4 GND
For a 6-wire load cell that includes sense wires, see Figure 2-2. Jumpers W2 and W3 must
J5-5 -SIGNAL
be opened.
J5-6 -SENSE
For load cells with an extra ground shield wire: Connect the shield to the center position (GND)
of J5. J5-7 -EXCITATION

Figure 2-2. Jumper Connections.

After wiring is completed and jumpers are in place, replace the indicator housing screws. Make sure the strain relief is properly
tightened.

2.3.3 RS232 Interface Cable to T31XW

Pass the optional RS232 cable through the strain relief (Figure 1-2, item 9) and attach it to
Pin Connection
terminal block J7 (Figure 1-3, item 7). Re-tighten the strain relief to ensure a water tight seal.
J7-1 TXD
J7-2 RXD
J7-3 GND
3000 Series Indicators EN-13

2.4 T31P Rear Cover Orientation

The T31P is delivered in the wall mount orientation
with the connections exiting below the display. The
rear housing may be reversed so the connections
exit above the display when the T31P is placed
horizontally on a bench. See Figure 2-4. To reverse
the rear housing, remove the four Phillips head
screws, carefully rotate the housing 180°, and
reinstall the screws.
CAUTION: Take care not to pinch any internal
cables attached inside. Figure 2-3. Wall Mount Configuration. Figure 2-4. Bench Top Configuration.

2.5 Direct Wall Mounting (T31P only)

The T31P indicator may be mounted directly to a wall using two screws (not included). Select appropriate size screws that fit
into the holes at the bottom of the indicator housing. See Figure 2-5. When mounting to a wall without a solid backing, use
appropriate anchoring hardware.

Wall Mounting Holes

Figure 2-5. T31P Direct Wall Mounting.

2.6 Mounting Bracket (T31XW only)

Attach the bracket to a wall or table using fasteners (not supplied) that are appropriate for the type of mounting surface. The
bracket will accommodate up to 6 mm (1/4”) diameter screws. Locate the mounting holes as shown in Figure 2-6.

Figure 2-6. Mounting Bracket Dimensions.

EN-14 3000 Series Indicators

3 SETTINGS
3.1 Menu Structure

TABLE 3-1. MENU STRUCTURE.

!"# /%)(0 $%"&'() 1'&% (-,) 0$,-) 1%-(2#'!8 %-&

.%/ .%/ .%/ .%/ .%/

.%/
$%/%) $%/%) $%/%) $%/%) $%/%) $%/%)
'(
/0"- '( '( '( '( '(

'-
8,#'3$"1/ M<< '++
'++ #'7 '- (33 N !"#,L$")%
"63
435 '- #%6%#
-./ !'(-) L"(& 8;!! ('
0120 '++ <
%8,!!
#,-%"$,). '-
0'(-&/ '++
(33 /%)(0
'++
!"# 45 !"#$
O%6%- ('
(-,) )* "*) %-& 0"$,). O'&&
%$
&$ - . 3$"1/
'-
O-?0
='>?
'++
<< (33
$%"&'()
=>
2.( %8 +/2!"0"!,). '-
('
&% /%#%!)2!"02 %:0"-&2 '-
1'&% '++ '(-!%/ =
"-&2(-,)
(33
/A?Q2 '++
LFAH >
1'&%
('
3$"&2 '++
L"!8 '- '-
0'(-&/9
%-& #,3;) '(-!%/
/%#%!)23$"& "()' (33
- . !"#$ '++
@('@(33
(-,)
'++

%&"'( ('
(33
A /;() 6.57% %-&
'++
0?PBJ2 BA
'++ 6.57,
6.57# - . /)"L#% '++ 0$,-)
)* '-#. ('
'@ ('
>C
(-,) 4*7>C
'++
DEF>
%-& "()'
'@2/ACDEB %-&
- . 0$,-) 1:FGHIJ)
- .
!?@AF@G?GH2
!+
*%$'
,+
$"-3%
%!!+
=/III
,-)%$ =1III
=;III

%-&
- .
3J?HH 'KK9(:
!?@AB@A

-BA 'KK9(:
)CJB 'KK9(:
(@FA 'KK9(:

%-&
- .
3000 Series Indicators EN-15

3.2 Menu Navigation

TO ENTER THE MENU MODE

Press and hold the Menu button until MENU appears on the display. The first upper level menu appears on the display.
Summary of button navigation functions in menu mode:
--Yes Allows entry into the displayed menu.
- Accepts the displayed setting and advances to the next menu item.
--No Skips by the displayed menu.
- Rejects the displayed setting or menu item and advances to the next available item.
--Back Moves backwards through the upper and middle level menus.
- Backs out of a list of selectable items to the previous middle level menu.
--Exit Exits from menu directly to the active weighing mode.

3.3 Calibration Menu

Two calibration processes are available: Span Calibration and Linearity
Span Perform
Calibration.
Linearity Perform
NOTES: Geographic
1. Make sure that appropriate calibration masses are available before Adjustment Set 00…Set 19… Set 31
beginning calibration. End Calibration Exit CALIBRATE menu
2. Make sure that the scale base is level and stable during the entire
calibration process.
3. Calibration is unavailable with LFT set to On.
4. Allow the Indicator to warm up for approximately 5 minutes after
stabilizing to room temperature.
5. To abort calibration, press the Exit button anytime during the calibration
process.
EN-16 3000 Series Indicators

3.3.1 Span Calibration

Span Calibration uses two points to adjust the scale. The first point is the zero value where there is no weight
on the scale. The second point is the Span value where a calibration mass is placed on the scale.

When SPAN is displayed, press the Yes button to access the Span Calibration menu item.

The display flashes 0.

With no weight on the scale, press the Yes button to establish the zero point.

The display shows --C-- while the zero point is established.

The display flashes the span calibration point. Place the specified weight on the scale and press the Yes
button.

To choose a different span point, repeatedly press the No button to increment the selections or press the Back
button to decrement the selections. Refer to Table 3-3 for available span points. When the desired value is
displayed, place the specified weight on the scale and press the Yes button.

The display shows --C-- while the span point is established.

If span calibration was successful, the scale exits to the active weighing mode and displays the actual weight
value.
!

3.3.2 linearity Calibration

Linearity calibration uses 3 calibration points. The first calibration point is established with no weight on the
scale. The second calibration point is established at approximately half capacity. The third calibration point
is established at capacity. The Linearity calibration points are fixed and cannot be altered by the user during
the calibration procedure. Refer to Table 3-3 for the linearity points.
When LINEAr is displayed, press the Yes button to access the Linearity Calibration menu item.

The display flashes 0. With no weight on the scale, press the Yes button to establish the zero point.

The display shows --C-- while the zero point is established.

The display flashes the mid calibration point.

Place the specified weight on the scale and press the Yes button.

The display shows --C-- while the mid point is established.

The display flashes the full calibration point.

Place the specified weight on the scale and press the Yes button.

The display shows --C-- while the full point is established.

If linearity calibration was successful, the scale exits to the active weighing mode and displays the actual
weight value.
!
3000 Series Indicators EN-17

3.3.3 Geographical Adjustment Factor

The Geographcial Adjustment Factor (GEO) is used to compensate for variations in gravity.

Note: Changing the GEO Factor alters the calibration. The GEO value was set at the factory and should only
be changed by an authorized manufacturer’s representative or certified verirication personnel.

Refer to table 3-2 to determine the GEO factor that corresponds to your location.

3.3.4 End Calibration

Advance to the next menu.
EN-18 3000 Series Indicators
TABLE 3-2. GEOGRAPHICAL ADJUSTMENT VALUES
Geographical latitude Elevation above sea level in meters
0 325 650 975 1300 1625 1950 2275 2600 2925 3250
away from the equator,
325 650 975 1300 1625 1950 2275 2600 2925 3250 3575
(North or South) in Elevation above sea level in feet
degrees and minutes. 0 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660
1060 2130 3200 4260 5330 6400 7460 8530 9600 10660 11730
0°00’ - 5°46’ 5 4 4 3 3 2 2 1 1 0 0
5°46’ - 9°52’ 5 5 4 4 3 3 2 2 1 1 0
9°52’ - 12°44’ 6 5 5 4 4 3 3 2 2 1 1
12°44’ - 15°06’ 6 6 5 5 4 4 3 3 2 2 1
15°06’ - 17°10’ 7 6 6 5 5 4 4 3 3 2 2
17°10’ - 19°02’ 7 7 6 6 5 5 4 4 3 3 2
19°02’ - 20°45’ 8 7 7 6 6 5 5 4 4 3 3
20°45’ - 22°22’ 8 8 7 7 6 6 5 5 4 4 3
22°22’ - 23°54’ 9 8 8 7 7 6 6 5 5 4 4
23°54’ - 25°21’ 9 9 8 8 7 7 6 6 5 5 4
25°21’ - 26°45’ 10 9 9 8 8 7 7 6 6 5 5
26°45’ - 28°06’ 10 10 9 9 8 8 7 7 6 6 5
28°06’ - 29°25’ 11 10 10 9 9 8 8 7 7 6 6
29°25’ - 30°41’ 11 11 10 10 9 9 8 8 7 7 6
30°41’ - 31°56’ 12 11 11 10 10 9 9 8 8 7 7
31°56’ - 33°09’ 12 12 11 11 10 10 9 9 8 8 7
33°09’ - 34°21’ 13 12 12 11 11 10 10 9 9 8 8
34°21’ - 35°31’ 13 13 12 12 11 11 10 10 9 9 8
35°31’ - 36°41’ 14 13 13 12 12 11 11 10 10 9 9
36°41’ - 37°50’ 14 14 13 13 12 12 11 11 10 10 9
37°50’ - 38°58’ 15 14 14 13 13 12 12 11 11 10 10
38°58’ - 40°05’ 15 15 14 14 13 13 12 12 11 11 10
40°05’ - 41°12’ 16 15 15 14 14 13 13 12 12 11 11
41°12’ - 42°19’ 16 16 15 15 14 14 13 13 12 12 11
42°19’ - 43°26’ 17 16 16 15 15 14 14 13 13 12 12
43°26’ - 44°32’ 17 17 16 16 15 15 14 14 13 13 12
44°32’ - 45°38’ 18 17 17 16 16 15 15 14 14 13 13
45°38’ - 46°45’ 18 18 17 17 16 16 15 15 14 14 13
46°45’ - 47°51’ 19 18 18 17 17 16 16 15 15 14 14
47°51’ - 48°58’ 19 19 18 18 17 17 16 16 15 15 14
48°58’ - 50°06’ 20 19 19 18 18 17 17 16 16 15 15
50°06’ - 51°13’ 20 20 19 19 18 18 17 17 16 16 15
51°13’ - 52°22’ 21 20 20 19 19 18 18 17 17 16 16
52°22’ - 53°31’ 21 21 20 20 19 19 18 18 17 17 16
53°31’ - 54°41’ 22 21 21 20 20 19 19 18 18 17 17
54°41’ - 55°52’ 22 22 21 21 20 20 19 19 18 18 17
55°52’ - 57°04’ 23 22 22 21 21 20 20 19 19 18 18
57°04’ - 58°17’ 23 23 22 22 21 21 20 20 19 19 18
58°17’ - 59°32’ 24 23 23 22 22 21 21 20 20 19 19
59°32’ - 60°49’ 24 24 23 23 22 22 21 21 20 20 19
60°49’ - 62°09’ 25 24 24 23 23 22 22 21 21 20 20
62°90’ - 63°30’ 25 25 24 24 23 23 22 22 21 21 20
63°30’ - 64°55’ 26 25 25 24 24 23 23 22 22 21 21
64°55’ - 66°24’ 26 26 25 25 24 24 23 23 22 22 21
66°24’ - 67°57’ 27 26 26 25 25 24 24 23 23 22 22
67°57’ - 69°35’ 27 27 26 26 25 25 24 24 23 23 22
69°35’ - 71°21’ 28 27 27 26 26 25 25 24 24 23 23
71°21’ - 73°16’ 28 28 27 27 26 26 25 25 24 24 23
73°16’ - 75°24’ 29 28 28 27 27 26 26 25 25 24 24
75°24’ - 77°52’ 29 29 28 28 27 27 26 26 25 25 24
77°52’ - 80°56’ 30 29 29 28 28 27 27 26 26 25 25
80°56’ - 85°45’ 30 30 29 29 28 28 27 27 26 26 25
85°45’ - 90°00’ 31 30 30 29 29 28 28 27 27 26 26
3000 Series Indicators EN-19

3.4 Setup Menu

When the Indicator is used for the first time, enter this
Reset No, Yes
menu to set the Capacity and Graduation.
Legal for Trade Off, On
Cal Unit kg, lb
Capacity 5…20000
Graduation 0.001…20
Power On Unit g, kg, lb, oz, lb:oz, Auto
Zero Range 0%, 2%, 100%
End Setup Exit SETUP menu

3.4.1 Reset
Reset the Setup menu to the factory defaults.
No = not reset.
Yes = reset.

NOTE: If the Legal for Trade menu item is set to ON, the Capacity, Graduation, Zero Range and Legal For
Trade settings are not reset.

3.4.2 Legal for Trade

Set the legal for trade status.
OFF = off
ON = on
Turning on the “LFT” menu setting has the following effects:
• Zero-range is set and locked on “2”.
• Auto Zero Tracking is set and locked on 0.5d
• The lb:oz unit is not available as a power-on setting.

3.4.3 Calibration Unit

Set the unit during calibration.
CAL UN kg = Calibrate using kg weights
CAL UN lb = Calibrate using pound weights

3.4.4 Capacity
Set the scale capacity from 5 to 20000. Refer to the Setup Table 3.3 for available settings.
EN-20 3000 Series Indicators

TABLE 3-3. SETUP AND CALIBRATION VALUES

Capacity Graduation size Graduation size with LFT ON Span calibration points Linearity
with LFT OFF calibration
points
5 0.0005, 0.001, 0.002, 0.001, 0.002, 0.005 5 2, 5
0.005
10 0.0005, 0.001, 0.002, 0.002, 0.005, 0.01 5, 10 5, 10
0.005, 0.01
15 0.001, 0.002, 0.005, 0.01 0.005, 0.01 5, 10, 15 5, 15
20 0.001, 0.002, 0.005, 0.01, 0.005, 0.01, 0.02 5, 10, 15, 20 10, 20
0.02
25 0.002, 0.005, 0.01, 0.02 0.005, 0.01, 0.02 5, 10, 15, 20, 25 10, 25
30 0.002, 0.005, 0.01, 0.02 0.005, 0.01, 0.02 5, 10, 15, 20, 25, 30 15, 30
40 0.002, 0.005, 0.01, 0.02 0.01, 0.02 5, 10, 15, 20, 25, 30, 40 20, 40
50 0.005, 0.01, 0.02, 0.05 0.01, 0.02, 0.05 5, 10, 15, 20, 25, 30, 40, 50 25, 50
60 0.005, 0.01, 0.02, 0.05 0.01, 0.02, 0.05 5, 10, 15, 20, 25, 30, 40, 50, 60 30, 60
75 0.005, 0.01, 0.02, 0.05 0.02, 0.05 5, 10, 15, 20, 25, 30, 40, 50, 60, 75 30, 75
100 0.005, 0.01, 0.02, 0.05, 0.02, 0.05, 0.1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100 50, 100
0.1
120 0.01, 0.02, 0.05, 0.1 0.02, 0.05, 0.1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120 60, 120
150 0.01, 0.02, 0.05, 0.1 0.05, 0.1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150 75, 150
200 0.02, 0.01, 0.02, 0.05, 0.05, 0.1, 0.2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200 100, 200
0.1, 0.2
250 0.05, 0.1, 0.2 0.05, 0.1, 0.2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 120, 250
250
300 0.02, 0.05, 0.1, 0.2 0.05, 0.1, 0.2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 150, 300
250, 300
400 0.02, 0.05, 0.1, 0.2 0.1, 0.2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 200, 400
250, 300, 400
500 0.05, 0.1, 0.2, 0.5 0.1, 0.2, 0.5 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250, 500
250, 300, 400, 500
600 0.05, 0.1, 0.2, 0.5 0.1, 0.2, 0.5 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 300, 600
250, 300, 400, 500, 600
750 0.05, 0.1, 0.2, 0.5 0.2, 0.5 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 300, 750
250, 300, 400, 500, 600, 750
1000 0.05, 0.1, 0.2, 0.5, 1 0.2, 0.5, 1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 500, 1000
250, 300, 400, 500, 600, 750, 1000
1200 0.1, 0.2, 0.5, 1 0.2, 0.5, 1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 600, 1200
250, 300, 400, 500, 600, 750, 1000, 1200
1500 0.1, 0.2, 0.5, 1 0.5, 1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 750, 1500
250, 300, 400, 500, 600, 750, 1000, 1200, 1500
2000 0.1, 0.2, 0.5, 1, 2 0.5, 1, 2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 1000, 2000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000
2500 0.2, 0.5, 1, 2 0.5 ,1, 2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 1200, 2500
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500
3000 0.2, 0.5, 1, 2 0.5 ,1 ,2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 1500, 3000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000
5000 0.5, 1, 2, 5 1, 2, 5 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 2500,5000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000
6000 0.5, 1, 2, 5 1, 2, 5 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 2500,5000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 6000
7500 0.5, 1, 2, 5 2, 5 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 3000,7500
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 6000, 7500
10000 0.5, 1, 2, 5, 10 2, 5, 10 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 5000,10000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 6000, 7500, 10000
12000 1, 2, 5, 10, 20 2, 5, 10 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 6000,12000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 6000, 7500, 10000, 12000
15000 1, 2, 5, 10 5, 10 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 7500,15000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 6000, 7500, 10000, 12000, 15000
20000 1, 2, 5, 10, 20 5, 10, 20 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 10000,20000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 6000, 7500, 10000, 20000
3000 Series Indicators EN-21

3.4.5 Graduation
Set the scale readability.
0.001, 0.002, 0.005, 0.01, 0.02, 0.05, 0.1, 0.2, 0.5, 1, 2, 5, 10, 20.
NOTE: Not all settings are available for each capacity. Refer to the Setup Table 3.3 for available settings.
•
•
•

3.4.6 Power On Unit

Set the unit that will be active at power on.
oz, lb, g, kg, lb:oz or
Auto (last unit in use when power was turned off.)

3.4.7 Zero Range

Set the percentage of scale capacity that may be zeroed.
0% = zeroing disabled
2% = zero up to 2 percent of capacity
100% = zero up to full capacity

3.4.8 End Setup

Advance to the next menu.

3.5 Readout Menu

Enter this menu to customize display functionality.
Reset: No, Yes
Filter Level Lo, Med, Hi
Auto Zero Tracking Off, 0.5d, 1d, 3d
Backlight Off, On, Auto
Auto Shut Off Off
End Readout Exit READOUT menu

3.5.1 Reset
Set the Readout menu to factory default settings.
No = not reset
Yes = reset
If the Legal for Trade menu item is set to ON, the Stable Range, Averaging Level, Auto Zero Tracking and Auto
Off settings are not reset.
EN-22 3000 Series Indicators

3.5.2 Filter
Set the amount of signal filtering.
LO = less stability, faster stabilization time (<1 sec.)
MEd = normal stability, stabilization time (<2 sec.)
HI = greater stability, slower stabilization time (<3 sec.)

3.5.3 Auto-Zero Tracking

Set the automatic zero tracking functionality.
OFF = disabled.
0.5 d = the display will maintain zero until a drift of 0.5 divisions per second has been
exceeded.
1d = the display will maintain zero until a drift of 1 division per second has been
exceeded.
3d = the display will maintain zero until a drift of 3 divisions per second has been
exceeded.

NOTE: When the LFT menu item is set to ON, the selections are limited to 0.5d and 3d. The setting is
locked when the hardware lock switch is set to the ON position.

3.5.4 Backlight
Set the display backlight functionality.
OFF = always off.
ON = always on.
AUtO = turns on when a button is pressed or the displayed weight changes.
turns off after 5 seconds of no activity.

3.5.5 Auto Off Timer

Set the automatic shut off functionality.
OFF = disabled
SEt 1 = powers off after 1 minute of no activity.
SEt 2 = powers off after 2 minutes of no activity.
SEt 5 = powers off after 5 minutes of no activity.

3.5.6 End Readout

Advance to the next menu.
3000 Series Indicators EN-23

3.6 Mode Menu

Enter this menu to activate the desired application
Reset: No, Yes
modes.
Count: Off, On
End Mode Exit MODE menu

3.6.1 Reset
Set the Mode menu to the factory defaults.
No = not reset.
Yes = reset.
NOTE: If the Legal for trade menu item is set ON, the settings are not reset.

3.6.2 Parts Counting Mode

Set the status.
OFF = Disabled
ON = Enabled

3.6.3 End Mode

Advance to the next menu.
EN-24 3000 Series Indicators

3.7 Unit Menu

Enter this menu to activate the desired units.
Default settings are bold. Reset: No, Yes
Kilograms: Off, On
Pounds: Off, On
Grams: Off, On
Ounces: Off, On
Pounds:Ounces Off, On
End Unit Exit UNIT menu

3.7.1 Reset
Set the Unit menu to the factory defaults.
Settings:
NO = not reset.
YES = reset
If the Legal for Trade menu item is set ON, the settings are not reset.

3.7.2 Kilogram Unit

kg
Set the status.
OFF = Disabled
ON = Enabled

3.7.3 Pound Unit

Set the status.
OFF = Disabled
ON = Enabled

3.7.4 Gram Unit

Set the status.
OFF = Disabled
ON = Enabled

3.7.5 Ounce Unit

Set the status.
OFF = Disabled
ON = Enabled

3.7.6 Pound Ounce Unit

Set the status.
OFF = Disabled
ON = Enabled
3000 Series Indicators EN-25

3.7.7 End Unit

Advance to the next menu.

3.8 Print Menu

Enter this menu to define printing parameters. Default settings are bold. Reset No, Yes
Baud Rate: 300, 600, 1200, 2400, 4800,
9600, 19200
Parity: 7 Even, 7 Odd, 7 None, 8 None
3.8.1 Reset
Stop Bit 1 or 2
Set the Print menu to factory defaults.
Handshake: Off, XON/XOFF
NO = not reset. Stable Only Off, On
Auto Print Off,
YES = reset. On Stable (-> Load, Load and Zero),
Interval (-> 1…3600), Continuous

NOTE: If the Legal for Trade menu item is set to ON, the following Content Gross (->Off, On)
settings are not reset: Stable, Auto Print Net (->Off, On)
Tare (->Off, On)
Unit (->Off, On)
End Print

Exit PRINT menu

3.8.2 Baud
Set the Baud rate.
300 = 300 bps
600 = 600 bps
1200 =1200 bps
2400 = 2400 bps
4800 = 4800 bps
9600 = 9600 bps
19200 = 19200 bps

3.8.3 Parity
Set the data bits and parity.
7 EVEN = 7 data bits, even parity.
7 Odd = 7 data bits, odd parity.
7 NONE = 7 data bits, no parity.
8 NONE = 8 data bits, no parity.
EN-26 3000 Series Indicators

3.8.4 Stop Bit

Set the number of stop bits.
1 = 1 stop bit.
2 = 2 stop bits.

3.8.5 Handshake
Set the flow control method.
NONE = no handshaking.
ON-OFF = XON/XOFF software handshaking.

3.8.6 Print Stable Data Only

Set the print critera.
OFF = values are printed immediately.
ON = values are only printed when the stability criteria are met.

3.8.7 Auto Print

Set the automatic printing functionality.
OFF = disabled.
ON.StAb = printing occurs each time the stability criteria are met.
INtEr = printing occurs at the defined interval.
CONt = printing occurs continuosly.

When INtEr is selected, set the Print Interval.

1 to 3600 (seconds)

3.8.8 Content
Select the additional content of the printout.
GROSS OFF = Gross weight is not printed.
ON = Gross weight is printed.
NET OFF = Net weight is not printed.
ON = Net weight is printed.
TARE OFF = Tare weight is not printed.
ON = Tare weight is printed.
UNIT OFF = Unit is not printed.
ON = Unit weight is printed.

3.8.9 End Print

Advance to the next menu.
3000 Series Indicators EN-27

3.9 Menu Lock Menu

Enter this menu. Default settings are bold. Reset: No, Yes
Lock Calibration Menu Off, On
Lock Setup Menu Off, On
Lock Readout Menu Off, On
Lock Mode Menu Off, On
Lock Unit Menu Off, On
Lock Print Menu Off, On
End Lock Menu

3.9.1 Reset
Set the menu Lock menu to factory defaults.
NO = not reset.
YES = reset.

NOTE: Settings for LFT controlled menu items are not reset.

3.9.2 Lock Calibration

Set the status.
OFF = Calibration menu is not locked.
ON = Calibration menu is locked and hidden.

3.9.3 Lock Setup

Set the status.
OFF = Setup menu is not locked.
ON = Setup menu is locked and hidden.

3.9.4 Lock Readout

Set the status.
OFF = Readout menu is not locked.
ON = Readout menu is locked and hidden.

3.9.5 Lock Mode

Set the status.
OFF = Mode menu is not locked.
ON = Mode menu is locked and hidden.

3.9.6 Lock Unit

Set the status.
OFF = Unit menu is not locked.
ON = Unit menu is locked and hidden.
EN-28 3000 Series Indicators

3.9.7 Lock Print

Set the status.
OFF = Print menu is not locked.
ON = Print menu is locked.

3.9.8 End Lock

Advance to the next menu.

3.10 Security Switch

A security switch is located on the Main PCB board. When the switch is set to the on position, user menu settings that were
locked in the Menu Lock can not be changed.

Open the housing as explained in Section 2.3.1. Set the position of security switch to ON as shown in Figure 1-3.

4 OPERATION
4.1 Turning Indicator On/Off
To turn the Indicator on, press the and hold the ON/ZERO Off button for 2 seconds. The Indicator
performs a display test, momentarily displays the software version, and then enters the active
weighing mode.

To turn the Indicator off, press and hold the ON/ZERO Off button until OFF is displayed.

4.2 Zero Operation

Zero can be set under the following conditions:
• Automatically at Power On (initial zero).
• Semi-automatically (manually) by pressing the ON/ZERO Off button.
• Semi-automatically by sending the Zero command (Z or alternate zero command).

Press the ON/ZERO Off button to zero the weight display. The scale must be stable to accept zero
operation.

4.3 Manual Tare

When weighing an item that must be held in a container, taring stores the container weight in
memory. Place the empty container on the scale (example 0.5 kg) and press the TARE button.
The display will show the net weight.

To clear the Tare value, empty the scale and press the TARE button. The display will show the
gross weight.
3000 Series Indicators EN-29

4.4 Changing Units of Measure

Press and hold the PRINT Units button until the desired measuring unit appears. Only measuring units enabled in the Unit Menu
will be displayed (refer to Section 3.7).

4.5 Printing Data

Printing the displayed data to a printer or sending the data to a computer requires that the communication parameters in the Print
Menu are set (refer to Section 3.8).

Press the PRINT Units button to send the displayed data to the communication port (the Auto-Print Mode in Section 3.8 function
must be Off).

4.6 Application Modes

Only modes enabled in the mode menu will be displayed (refer to Section 3-6).

4.6.1 Weighing
Place the item to be weighed on the scale. The illustration indicates a sample of 1.5 kg, Gross
weight.

Note: To return to the Weighing mode from the Parts Counting mode, press and hold the Mode
button until WEIGH is displayed.

4.6.2 Parts Counting

Use this mode to count parts of uniform weight. The Indicator determines the quantity based on the
average weight of a single part. All parts must be uniform in weight for accurate measurements.

To enter the Parts Counting mode, press and hold the Mode button until Count is displayed.

Average Piece Weight (APW)

When the Mode button is released, CLr.PW Pcs is displayed.

NOTE: If no APW has been previously stored, the CLr.PW display is skipped and the display shows
PUt10Pcs.

Clearing a Stored APW

Press the Yes button to clear the stored APW.
EN-30 3000 Series Indicators

Recalling a Stored APW

Press the No button to recall the existing APW.

Press the FUNCTION Mode button to temporarily display the APW value.

Establishing the Average Piece Weight (APW)

The display shows Put10 Pcs.

Establishing a New APW

Press the No button to increment the sample size. Choices are 5, 10, 20, 50, 100 and 200.

To establish the APW, place the specified quantity of samples on the scale and press the Yes
button to capture the weight.

Begin Counting
Place the parts on the scale and read the count. If a container is used, be sure to tare the empty
container first.
3000 Series Indicators EN-31

5 SERIAL COMMUNICATION
The T31P and T31XW Indicators include an RS232 serial communication interface.

The setup of RS232 operating parameters are more fully explained in Section 3.8. The physical hardware connection is
explained in in Section 2.2.

The interface enables display data to be sent to a computer or printer. A computer can be used to control some functions of
the indicator using the commands listed in Table 5-1.

5.1 Interface Commands

Communicate to the indicator using the command characters listed in Table 5-1.
TABLE 5-1. SERIAL INTERFACE COMMAND TABLE.

Command Function
Character
IP Immediate Print of displayed weight (stable or unstable).
P Print stable displayed weight (according to stability setting).
CP Continuous Print.
SP Print when stable.
xP Interval Print x = Print Interval (1-3600 sec)
Z Same as pressing Zero button
T Same as pressing Tare button
xT Download Tare value in grams (positive values only). Sending 0T clears tare (if allowed)
PU Print current unit: g, kg, lb, oz, lb:oz
xU Set scale to unit x: 1=g, 2=kg, 3=lb, 4=oz, 5=lb:oz
PV Version: print name, software revision and LFT ON (if LFT is set ON).
Esc R Global reset to reset all menu settings to the original factory defaults

NOTES:
• Commands sent to the Indicator must be terminated with a carriage return (CR) or carriage return-line feed (CRLF).
• Data output by the Indicator is always terminated with a carriage return-line feed (CRLF).
EN-32 3000 Series Indicators

5.2 Output Format

The default serial output format is shown below.

Field: Polarity Space Weight Space Unit Stability Legend CR LF

Length: 1 1 7 1 5 1 3 1 1

Definitions: Polarity, “-” sign if negative, blank if positive.

Weight, up to 6 numbers and 1 decimal, right justified, leading zero blanking.
Units, up to 5 characters.
Stability, “?” character is printed if not stable, blank if stable.
Legend, up to 3 characters: G = gross weight, NET = net weight, T = tare
3000 Series Indicators EN-33

6. LEGAL FOR TRADE

6.1 Settings
Enter the menu to verify the settings and perform a calibration as explained in Section 3.
Set the LFT menu to ON. Exit the Setup menu and power off the indicator.

Open the housing as explained in Section 2.3.1.

Set the position of the security switch to ON as shown in Figure 1-3, (item 9).
Close the housing.

NOTE: When LFT is set to ON and the security switch is set to ON, the following menu settings cannot be changed:
Span Calibration, Linearity Calibration, Calibration Unit, GEO, LFT, Capacity, Graduation, Zero Range, Stable Range, AZT, Modes,
Units. To enable editing of these menu settings, return the security switch to the off position and set LFT menu item to off.

6.2 Verification
Before this product can be used in a trade approved application, it must be inspected in accordance with local weights and
measures regulations. It is the responsibility of the purchaser to ensure that all pertinent legal requirements are met. Please
contact your local weights and measures office for further details.

6.3 Sealing
The weights and measures official can apply a wire or paper security seal as shown below.

Figure 6-1. T31P Wire Seal Figure 6-2. T31P Paper Seal

SEAL

SEAL

Figure 6-3. T31XW Wire Seal Figure 6-4. T31XW Paper Seal
EN-34 3000 Series Indicators

7 MAINTENANCE
CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE CLEANING.
7.1 Model T31P Cleaning
• The housing may be cleaned with a cloth dampened with a mild detergent if necessary.
• Do not use solvents, chemicals, alcohol, ammonia or abrasives to clean the housing or control panel.

7.2 Model T31XW Cleaning

• Use approved cleaning solutions for the stainless-steel Indicator housing and rinse with water. Dry thoroughly.
• Do not use solvents, chemicals, alcohol, ammonia or abrasives to clean the control panel.

7.3 Troubleshooting
TABLE 7-1. TROUBLESHOOTING.
SYMPTOM PROBABLE CAUSE(s) REMEDY
Unit will not turn on. Power cord not plugged in or properly Check power cord connections. Make sure
connected. power cord is plugged in properly into the
power outlet.

Power outlet not supplying electricity. Check power source.

Battery power used up. (T31P Only) Reconnect AC power to charge the battery.

Other failure. Service required.

Cannot zero the Scale, or will not zero when Load on Scale exceeds allowable limits. Remove load on Scale.
turned on.
Load on Scale is not stable. Wait for load to become stable.

Load Cell damage. Service required.

Unable to calibrate. Lock Calibration Menu set to On. Set Lock Calibration Menu to Off.
Refer to Section 3.9 Menu Lock.
Lock switch is “on”. Set the Lock switch to Off.

LFT menu set to On. Set LFT menu to Off.

Incorrect value for calibration mass. Use correct calibration mass.

Cannot display weight in desired weighing Unit not set to On. Enable unit in the Units Menu.
unit. Refer to Section 3.7 in the Unit Menu.
Cannot change menu settings. Menu has been locked. Set selected menu to Off in the Lock Menu.
Lock Switch on the circuit board may
need to be set to the Off position.

Lock switch set on. Set the Lock switch to off.

Battery indicator is flashing. (T31P Only) Battery discharged. Connect indicator to power and charge
battery.
Battery fails to charge fully. (T31P Only) Battery is defective. Have the battery replaced by an authorized
Ohaus service dealer.
Error 7.0 Unstable weight reading when defining Unstable Error, check platform location.
reference weight.
Error 8.1 Weight reading exceeds Power On Zero limit. Remove load from scale. Recalibrate scale.
Error 8.2 Weight reading below Power On Zero limit. Add load to scale. Recalibrate scale.
Error 8.3 Weight reading exceeds Overload limit. Reduce load on scale.
Error 8.4 Weight reading below Underload limit. Add load to scale. Recalibrate scale.
3000 Series Indicators EN-35

TABLE 7-1. TROUBLESHOOTING (Cont.).

SYMPTOM PROBABLE CAUSE(s) REMEDY

Err 9.0 Internal fault Service required.
Err 9.5 Calibration data not present. Calibrate scale.
Err 53 EEPROM data incorrect. Service required.
CAL E Calibration Error. Calibration value outside Repeat calibration using correct calibration
allowable limits. weights.
LOW.rEF The average piece weight of the parts is small Use parts with average piece weight greater
(warning). than or equal to 1 division.

7.4 Service Information

If the troubleshooting section does not resolve your problem, contact an authorized Ohaus Service Agent. For Service assistance
in the United States, call toll-free 1-800-526-0659 between 8:00 AM and 5:00 PM Eastern Standard Time. An Ohaus Product
Service Specialist will be available to assist you. Outside the USA, please visit our website www.ohaus.com to locate the Ohaus
office nearest you.
EN-36 3000 Series Indicators

8. TECHNICAL DATA
8.1 Specifications
Materials
T31XW Housing: stainless steel
T31P Housing: ABS plastic
Keypad: polyester
Feet: Rubber
Display Window: Polycarbonate

Ambient conditions
The technical data is valid under the following ambient conditions:
Ambient temperature: -10°C to 40°C / 14°F to104°F
Relative humidity: Maximum relative humidity 80% for temperatures up to 31°C decreasing linearly to 50%
relative humidity at 40°C.
Height above sea level: up to 4000m
Operability is assured at ambient temperatures between -10°C. and 40°C.

TABLE 8-1. SPECIFICATIONS

Indicator T31P T31XW
Capacity Range 5 to 20000 kg or lb
Maximum Displayed Resolution 1:20,000
Type Approved Resolution 1:6,000
Minimum Average Piece Weight 1d
(APW)
Weighing Units kg, lb, g, oz, lb:oz
Functions Weighing, Parts Counting
Display 1 in./2.5 cm digit height, 6-digit, 7-segment
1.5 in./3.8 cm high x 4.9 in./12.5 cm wide backlit LCD
Backlight White LED
Keypad 4-button mechanical switches 4-button membrane switch
Ingress Protection --- IP66
Load Cell Excitation Voltage 5V DC
Load Cell Drive Up to 4 x 350 ohm Load Cells
Load Cell Input Sensitivity Up to 3 mV/V
Stabilization Time Within 2 Seconds
Auto-zero Tracking Off, 0.5, 1 or 3 Divisions
Zeroing Range 0%, 2% or 100% of Capacity
Span Calibration 5 kg or 5 lb to 100% Capacity
Interface RS232
Overall Dimensions (W x D x H) 8.2 x 2.8 x 6.5 / 210 x 71 x 168 8.3 x 2.8 x 5.8 / 212 x 71 x 149
(in/mm)
Net Weight (lb/kg) 3.6 / 1.6 6.6 / 2.9
Shipping Weight (lb/kg) 5.7 / 2.6 8.8 / 4.0
Operating Temperature Range -10°C to 40°C/14°F to 104°F
Power 9 - 12VDC, 0.5A, AC Adapter with Internal rechargeable, Sealed Lead-Acid
Battery (100-hour typical life) (T31P)

100-240 VAC / 50-60 Hz, Internal Power Supply (T31XW)

3000 Series Indicators EN-37

8.2 Accessories

TABLE 8-2. ACCESSORIES.

DESCRIPTION PART NUMBER
Column Mount Kit, 35 cm painted steel 80251743
Column Mount Kit, 70 cm painted steel 80251744
Column Mount Kit, 35 cm stainless steel 80251745
Column Mount Kit, 70 cm stainless steel 80251746
Wall Mount Kit, T31P 80251747
Wall Mount Kit, T31XW 80251748
Interface Cable/PC 25-pin, T31P 80500524
Interface Cable/PC 9-pin, T31P 80500525
Interface Cable/PC 9-pin, T31XW 80500552
Interface Cable/PC 25-pin, T31XW 80500553
Interface Cable/Printer SF42, T31P 80500571
Interface Cable/Printer SF42, T31XW 80500574
SF42 Printer SF42
EN-38 3000 Series Indicators

8.3 Drawings and Dimensions

Figure 8-1. T31P Indicator Overall Dimensions.

Figure 8-2. T31XW Indicator Overall Dimensions with Mounting Bracket.

 LIMITED WARRANTY

Ohaus products are warranted against defects in materials and workmanship from the date of delivery through the duration of
the warranty period. During the warranty period Ohaus will repair, or, at its option, replace any component(s) that proves to be
defective at No charge, provided that the product is returned, freight prepaid, to Ohaus.

This warranty does Not apply if the product has been damaged by accident or misuse, exposed to radioactive or corrosive
materials, has foreign material penetrating to the inside of the product, or as a result of service or modification by other than
Ohaus. In lieu of a properly returned warranty registration card, the warranty period shall begin on the date of shipment to the
authorized dealer. No other express or implied warranty is given by Ohaus Corporation. Ohaus Corporation shall Not be liable
for any consequential damages.

As warranty legislation differs from state to state and country to country, please contact Ohaus or your local Ohaus dealer for
further details.
Ohaus Corporation
19A Chapin Road
P.O. Box 2033
Pine Brook, NJ 07058, USA
Tel: (973) 377-9000
Fax: (973) 593-0359
www.ohaus.com

*80251064*
P/N 80251064 B © Ohaus Corporation 2008, all rights reserved.

Printed in China