For the latest prices, please check AutomationDirect.com.

Standard PLC
Built-in I/O Specifications - Inputs
C0-01DD1-D Inputs per Module 8 (Sink/Source)

8 DC Input/6 Sinking DC Output Micro PLC Operating Voltage Range 24VDC

Input Voltage Range 21.6–26.4 VDC
X1-2: Typ 5mA @ 24VDC
Wiring Diagram Input Current X3-8: Typ 4mA @ 24VDC
X1-2: 6.0 mA @ 26.4 VDC
C0-01DD1-D 24VDC Maximum Input Current X3-8: 5.0 mA @ 26.4 VDC
X1-2: 4.7 k @ 24VDC
Input Impedance X3-8: 6.8 k @ 24VDC

+
X1-2: > 19VDC
ON Voltage Level

+
X3-8: > 19VDC
PWR
X1-2: < 4VDC
RUN OFF Voltage Level X3-8: < 7VDC
ERR
X1-2: 4.5 mA

+
Minimum ON Current X3-8: 3.5 mA
+
PORT1
X1-2: 0.1 mA
TX1 Maximum OFF Current X3-8: 0.5 mA
RX1
X1-2: Typ 5µs Max 20µs
OFF to ON Response X3-8: Typ 2ms Max 10ms
TX2 L
X1-2: Typ 5µs Max 20µs
RX2 L ON to OFF Response X3-8: Typ 3ms Max 10ms
PORT2
+

L 5 - 27VDC
L Status Indicators Logic Side (8 points, green LED)
RS-485
PORT3 Commons 2 (4 points/common) Isolated
TX3
L
+

L
Built-in I/O Specifications - Outputs
+

RX3
5 - 27VDC 24VDC

Outputs per Module 6 (Sink)

Operating Voltage Range 5–27 VDC
Output Voltage Range 4–30 VDC
NOTE: When using Standard PLCs, you must use CLICK 0.1 A/point; C3: 0.4 A/common, C4: 0.2
Maximum Output Current A/common
programming software version V1.20 or later.
Minimum Output Current 0.2 mA
Equivalent Input Circuit Maximum Leakage Current 0.1 mA @ 30.0 VDC
Internal Module Circuitry On Voltage Drop 0.5 VDC @ 0.1 A
Maximum Inrush Current 150mA for 10ms
INPUT Optical Isolator
Y1: typ 5µs; max 20µs
+
X1-X4
Typical OFF to ON Response Y2-6: < 0.5 ms
+
Y1: typ 5µs; max 20µs
24 VDC ON to OFF Response Y2-6: < 0.5 ms
C1 COM
Status Indicators Logic Side (6 points, red LED)
To X2-X4
commons Commons 2 (4 points/com & 2 points/com)
INPUT
X5-X8
Optical Isolator
External DC Power 20–28 VDC Maximum @ 60mA
+ Typical Required (All Points On)
+
24 VDC
General Specifications
C2 COM

To X6-X8
Current Consumption at 24VDC 140mA
commons
Terminal Block Replacement Part No. C0-16TB
Equivalent Output Circuit Weight 5.0 oz (140g)
Internal Module Circuitry
ZIPLink Pre-Wired PLC
24 VDC C0-01DD1-D Temperature Derating Chart
+ +V
Optical Isolator Connection Cables and Modules
OUTPUT
+
L
Y1 8
High response
Inputs
5 - 27 VDC
* circuit
6
Outputs ZL-RTB20 20-pin
Points

4 feed-through

Optical Isolator 2
* connector module
OUTPUT
+ Y2-Y4
L
5 - 27 VDC * 0

C3 COM 0 10 20 30 40 50 55 °C
32 50 68 85 104 122 131 °F
Surrounding Temperature (°C/°F)
Optical Isolator * Use every other input/output.
OUTPUT
+ Y5-Y6
L
5 - 27 VDC
* 20-pin connector cable
C4 COM
ZL-C0-CBL20 (0.5 m length)
Note: C3 & C4 are not internally connected.
ZL-C0-CBL20-1 (1.0 m length)
ZL-C0-CBL20-2 (2.0 m length)
* Zener Diode Power Dissipation: 200 mW

www.automationdirect.com/click-plc CLICK PLCs tCLP-45