Scribd
Upload
96 views2 pages

Data Sheet Primer Anti-Static Ep-6-Bk1

This two-component epoxy primer is designed to produce an anti-static conductive film on fiberglass components. It can be top-coated with epoxy or polyurethane enamel. The primer must be thoroughly mixed in a 3:1 ratio of base to catalyst and applied in a single wet uniform coat between 1.3-1.8 mils thick using spray equipment. It provides resistivity between 0.1-100,000 ohms and dries to a flat black finish. Proper surface preparation is required to ensure adhesion by removing all corrosion, paint, and residue.

Uploaded by

Manuel Diaz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
96 views2 pages

Data Sheet Primer Anti-Static Ep-6-Bk1

This two-component epoxy primer is designed to produce an anti-static conductive film on fiberglass components. It can be top-coated with epoxy or polyurethane enamel. The primer must be thoroughly mixed in a 3:1 ratio of base to catalyst and applied in a single wet uniform coat between 1.3-1.8 mils thick using spray equipment. It provides resistivity between 0.1-100,000 ohms and dries to a flat black finish. Proper surface preparation is required to ensure adhesion by removing all corrosion, paint, and residue.

Uploaded by

Manuel Diaz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

EP-6-BK1

CONDUCTIVE EPOXY PRIMER


Technical Data April 2016

Product Description

This two-component epoxy primer is designed to produce anti-static conductive film on fiberglass components.
EP-6-BK1 can be top-coated with an epoxy or polyurethane enamel

Meets or Exceeds the Performance Requirement of Specification

Surface Preparation

To insure proper adhesion, remove all surface corrosion, paint films and residue indicated by a lack of water-
break free surface. Old paint in good condition must be sanded thoroughly and any residue removed by
washing, solvent wiping, and using a tack cloth.

Mixing / Application

Mix thoroughly, three parts EP-6-BK1 base component with one part EH-24 catalyst by volume. Pot life will be 8
hours. Spray apply a single wet uniform coat to a dry film thickness of 1.3 – 1.8 mils, using siphon, air, or
airless spray equipment. Constant agitation is suggested during product application

Physical Properties

Resistivity: 0.1 to 100,000 OHMs


Appearance: Flat Black
Admixed Viscosity: 35 +/- 5 seconds, #1 Zahn
Weight per Gallon: A) Admixed 7.2 - 7.8 lb./gal
B) Base 8.3 – 8.7 lb./gal
C) Catalyst 6.97 lb./gal
Volume Solids: A) Admixed 14-16 %
B) Base 22 – 26%
C) Catalyst 6.8%
Fineness of Grind: 5.5 Hegman
Coverage @ 100% Usage - No Loss: 350 sq ft/mil
Gloss < 10 units at 60 degrees

Precautions

Avoid skin contact. If eye contact is made, flush immediately and consult a physician. See MSDS for detailed physical
constituents. Do not spray this product with electrostatic equipment.

Hentzen Coatings, Inc. Email: [email protected] The information contained here is to our knowledge true and
307 Echelon Road P: 864.299.2819 accurate but all suggestions are made without guarantee since
conditions of use are beyond our control. Nothing contained herein
Greenville, SC 29605 F: 864.299.2820
shall be construed as a recommendation to use any product in
Hentzen.com conflict with existing patents covering any material or use.
Hentzen Coatings, Inc. Email: [email protected] The information contained here is to our knowledge true and
307 Echelon Road accurate but all suggestions are made without guarantee since
P: 864.299.2819
conditions of use are beyond our control. Nothing contained herein
Greenville, SC 29605 F: 864.299.2820 shall be construed as a recommendation to use any product in
Hentzen.com conflict with existing patents covering any material or use.

You might also like