Cost Abstract for Interior Furnishing of Regional Office of New India Assurance Co.

Ltd, at Lachit Nagar, Guwahati, Assam.

COST SUMMARY

INTERIOR FURNISHING WORKS OF CIRCLE OFFICE OF CANARA BANK

AT SIX MILE, V. I. P ROAD, GUWAHATI, ASSAM

SUMMARY SHEET

SL. NO ITEM DESCRIPTION AMOUNT (RS.)

A INTERIOR FURNISHING WORKS
1 CARPENTRY & INTERIOR WORKS

2 MODULAR FURNITURE

3 ELECTRICAL & OTHER RELATED WORKS

4 BROUGHT OUT ITEMS

A GRAND TOTAL

ARCHIVENTIONS- Architects Engineers, R.G. Baruah Road, Guwahati, Assam-781024

 ESTIMATED BOQ FOR CARPENTRY WORKS OF CIRCLE OFFICE AT SIX MILE, GUWAHATI, ASSAM
SR.NO DESCRIPTION UNIT QTY. RATE AMOUNT
A PARTITIONS
Note :- The rate shall be include of frame work above false ceiling level. Measurement should be taken up to false ceiling level
and visible portion only.
Basic rate of Laminate shall be considered as Rs 35/SFT and that of Veneer as 60/SFT
Note :- All Plwood and Block board to be used in Carpentry works should be BWP, Borer proof, termite proof and should
have a minimum of 10 years warranty. A valid warranty certificate from the company (plywood/Block Board Company as
used) shall have to be furnished by the contractor confirming the above and the same shall have to be submitted along
with the submission of the Final Bill
1 FULLY GLAZED PARTITION - WITH TOUGHENED GLASS
Providing and fixing of Fixed Glass partition with 10mm thick toughened glass using Standard fittings of above - mentioned
makes at the top and grouting at the bottom with U - Shaped Aluminium rails and EPDM gaskets including cutting, making
holes in glass and fixing the fittings in floors, false ceiling etc. and making the same good with necessary screw, sealent
wherever required. The top fittings to be fitted to the Wooden section fixed above the Gypsum board in the level of GI
channels of False ceiling.
a USING OZONE / HAFFLE / YALE / GODREJ MAKE FITTINGS S.FT. 801
2 FULLY GLAZED PARTITION WITH FLOAT GLASS
Providing and fixing partition framing which shall consist of Heavy duty Aluminium Box Sections 50mm x 50mm @ 600mm c/c
Horizontally and Vertically . The vertical alternate frames to be fixed to the ceiling with necessary fixtures. The framing shall be
finished with 8 mm thk. BWP ply on both side and finished with 1.00 mm thk. Laminate finished with melamine polish. The
shade of laminate and polishing finish to be got approved from the Architect. Approved make 10mm thick Clear Float glass to
be fixed from skirting level to 2100mm level ( in the top line of Door) The skirting should be as per approved laminate as per
drawing and direction. Rate shall be inclusive of necessary hardware items, etc. Complete. The edge beadings with steam
a beach wood
FINISHED should
WITH BOTH be SIDE
finished with melamine Polish.
LAMINATE S.FT.

3 FULL HT SOLID PARTITION

i Providing and fixing partition framing shall consist of Heavy duty Aluminium Box Sections 50mm x 50mm @ 600mm c/c both
ways Horizontally and Vertically. The vertical alternate frames to be fixed to the ceiling with necessary fixtures. The framing
shall be finished with 8 mm thk. BWP ply on both side and finished with 1.00 mm thk. Laminate / Veneer finished with
melamine polish. The shade of laminate / veneer and polishing finish to be got approved from the Architect. The skirting
should be as per approved laminate/Veneer as per drawing and direction. Rate shall be inclusive of necessary hardware items,
a etc. Complete.
FINISHED WITHThe edge
BOTH beadings
SIDE with steam beach wood should be finished with melamine Polish.
LAMINATE S.FT. 1640

b FINISHED WITH BOTH SIDE VENEER S.FT. 0

c FINISHED WITH BOTH SIDE PLY S.FT. 0

d FINISHED WITH ONE SIDE VENEER-ONE SIDE LAMINATE S.FT. 360

ii Providing and fixing partition framing shall consist of Heavy duty Aluminium Box Sections 50mm x 50mm @ 600mm c/c both SFT 198
ways Horizontally and Vertically. The vertical alternate frames to be fixed to the ceiling with necessary fixtures. The framing
shall be finished with 12 mm thk. BWP ply on one side and 8 mm BWP ply on the other side and finished with 1.00 mm thk.
Laminate / Veneer finished with melamine polish. The shade of laminate / veneer and polishing finish to be got approved from
the Architect. The skirting should be as per approved laminate/Veneer as per drawing and direction. Rate shall be inclusive of
necessary hardware items, etc. Complete. The edge beadings with steam beach wood should be finished with melamine Polish.
Note- All necessary piping for Air conditioning like- Drain Water Pipe and Copper pipe shall be drawn throgh the framework of
iii the partition
Providing andinfixing
a concealed
partitionway, without
framing shalldisturbing
consist ofthe ambience
Heavy of the room
duty Aluminium Box Sections 50mm x 50mm @ 600mm c/c both SFT 136
ways Horizontally and Vertically. The vertical alternate frames to be fixed to the ceiling with necessary fixtures. The framing
shall be finished with 12 mm thk. BWP ply on both side and finished with 1.00 mm thk. Laminate / Veneer finished with
melamine polish. The shade of laminate / veneer and polishing finish to be got approved from the Architect. The skirting
should be as per approved laminate/Veneer as per drawing and direction. Rate shall be inclusive of necessary hardware items,
etc. Complete. The edge beadings with steam beach wood should be finished with melamine Polish.Note- All necessary piping
for Air conditioning like- Drain Water Pipe and Copper pipe shall be drawn throgh the framework of the partition in a
concealed way, without disturbing the ambience of the room

4 FULL HEIGHT PARTLY GLAZED PARTITION IN LAMINATE

Specification same as Full Ht Solid Partition as above except for 8mm approved make clear float glass shall be provided above
2’-6” from ffl or as mentioned in the drawing and as advised by architect with necessary steam beach moulding finished with
melamine Polish. The rate shall include necessary etching film / LOGO.
a WITH BOTH SIDE LAMINATE S.FT. 510

5 SEMI HT. SEMI GLAZED PARTITION IN LAMINATE

Specification same as 4 above but of low ht as per the drawing. All external surface and edges to be finish with 1mm thk
laminate of approved shade & make. Providing and Fixing inserted Soft board / White boards / Glass maintaining the vertical
surface lines and no extra measurements would be taken for the soft boards / white boards / Glass.
a WITH BOTH SIDE LAMINATE S.FT. 2365

6 SLIDING AND FOLDING PARTITION S.FT. 180

Providing and making Sliding folding partition made in Aluminium section of 2"x1" like Top sliding 'G' channel pivoted wheels,
suspension system, bearing hinges (5") each door, conceled Towel bolt and handles, bottom "U" channel guide and no of leafs
are 3 full and 2 half leafs made of 2"x1" aluminium section frame filled with 24 kg density glass wool insulation wrapped FRP
tissue and finished with 8mm plywood on both sides over which necessary fabric and laminate finished as per drawing.THE
CHANELS TO BE USED SHALL BE OF DORMA AND EQ BRANDThe rate shall include all the necessary hardware necessary for
making complete as per the design.
B PANELLING
1 PANELLING ON WALLS - with frame
Providing and fixing panelling on wall. Framing shall consist of Heavy duty Aluminium Box Sections 50mm x 25 mm x @
600mm c/c Both ways horizontally and vertically on the wall.This framing would be covered by 8mm thk. BWP. Ply finished in
approved 1.0 mm. Thk. Laminate / Veneer finished in melamine polish. Wooden moulding, lipping etc. as directed by the
architect shall be provided wherever required.
a. WITH LAMINATE S.FT.

b. WITH VENEER S.FT.

2 PANELLING ON WALLS - With out frame

Same as (1) Above work with out frame using 12mm thk BWP ply and surface finished with Laminate / Veneer as the case may
be including polishing with melamine finish.
a. WITH LAMINATE S.FT. 1439

b. WITH VENEER (CRM, RM COLUMN PANELLING) S.FT. 295

3 PANNELLING ON WALLS WITH GYPSUM S.FT. 102

WITH FRAME
Providing and fixing panelling on wall. Framing shall consist of Aluminum Section 50 mm x 25 mm ( Wall Thickness 2 mm
approved make) @ 600MM C/C. Both ways horizontally and vertically on the wall. This framing would be covered by 6mm thk.
Ply and 12mm thk gypsum board.

C DOORS
2 ENTRANCE DOORS - WITH TOUGHENED GLASS (PATCH FITTINGS)
Providing and fixing frameless fully glazed 12mm thk toughened float glass fixed with necessary patch fittings(Dorma make)
including cutting, making holes, cutouts in the glass of required shape and size to acBWPodate fittings and fixing the fittings in
floors, soffits, jams including necessary fixtures, srews, sealent wherever required and SS cover over patch fittings. Rate shall
include necessary etching film / LOGO, approved patch fitting locking systems, 1 pair of 12” long S. S. (C Shape) Handles of
approved make, floor springs, and any necessary hardware items.(ABOVE MENTIONED MAKES Top Pivot , Top Patch Fittings,
Bottom Patch fittings , Floor Spring , Corner lock with strike plate and Euro Profile Cilinder, C Shape Handle 25mm dia X
300mm length)
a. DOORS - WITH OZONE / HAFFLE / YALE / GODREJ MAKE FITTINGS S.FT. 270
3 DOORS ON WOODEN PARTITION WALLS
a SOLID DOORS- IN LAMINATE FINISH (with hardware fittings MAKE EVERITE / GOLDEN /HARDWIN /EVEREST) ( WITH OR
WITH OUT VISION PANEL AS PER DIRECTION OF the ARCHITECT
Providing and fixing solid doors of sizes as shown in the drawing. The door shutter shall of 35 mm thick flush shutter of
approved make and finished with 1mm thick approved laminate on both sides. The edges finished with steam beach lipping. A
door frame of 3.5” x 2" steam beach section shall be provided finished in mellamine. Rate shall include Dead lock ( Godrej
Make), floor springs / door closure ( as the case may be), door stopper, a pair of handles 12" SS Brushed finished, 5" hinges 4
Nos., buffers, tower bolts, etc with necessary hardware items and with or with out door frames as mentioned above
i With Door Closure S.F.T. 140
b SOLID DOORS- IN VENEER FINISH (with hardware fittings MAKE EVERITE / GOLDEN /HARDWIN /EVEREST) ( WITH OR WITH
OUT VISION PANEL AS PER DIRECTION OF the ARCHITECT
Providing and fixing solid doors of sizes as shown in the drawing. The door shutter shall of 35 mm thick flush shutter of
approved make and finished with Vineer finished with melamine polish on both sides. The edges finished with steam beach
lipping. A door frame of 3.5” x 2" steam beach section shall be provided finished in mellamine. Rate shall include Dead lock (
Godrej Make), floor springs / door closure ( as the case may be), door stopper, a pair of handles 12" SS Brushed finished, 5"
hinges 4 Nos., buffers, tower bolts, etc with necessary hardware items and with or with out door frames as mentioned above
i With Door Closure with both side Veneer finish S.F.T. 17.5
ii same as above as 3 (b) but finished with one side laminate and one side veneer in mellamine polish with Door closer S.F.T 56
c TOILET DOORS (2'-6" X 7'-0" SIZE) ( with hardware fittings MAKE EVERITE / GOLDEN /HARDWIN /EVEREST)
Providing and fixing solid doors of sizes as shown in the drawing. The door shutter shall of 35 mm thick flush shutter of
approved make and finished with 1mm thick approved laminate on both sides. The edges finished with steam beach lipping
with melamine polish. A door frame of 2” x 3.5” Steam Beach wood section shall be provided finished in enamel paint. Rate
shall include approved door closure, door stopper, a pair of handles 9" SS Brushed finished, 5" hinges 4 Nos., buffers, tower
bolts, etc with necessary hardware items and with or with out door frames as mentioned above
D CARPENTRY WORKS

1 LOW HT. STORAGES (1'-6" DEPTH X 2'-6" HT.) (BACK CREDENZA)

Providing and laying low ht. Storage units of sizes as mentioned above. They shall consist of a top of ¾” thk. BWP. Ply, ¾” thk.
BWP. Ply sides and base, ¼” thk. Marine ply back, ¾” thk. BWP. Ply shutter with self closing higes of hafele make(full ovel open)
& PVC lipping matching with approved laminate/Veneer on all the edges. All external surfaces to be finished in 1.0 mm
laminate (suede finish)of approved make.
Division of shutters shall be made equally according to the length of the storage. A ¾” thk. Fixed BWP. Ply shelf on battens shall
be provided at 16” intervals from the base.
Suitable wooden moulding (as per Architects design) with mellamine shall be provided to the edge of the storage top. All inner
surfaces including shutters shall be finished with 0.80mm thk laminate of approved shade and colour
Rate shall be inclusive of all necessary approved fittings like hinges(Hafele make), locks(Godrej make/Vijayan), 3" long brushed
finish handles(kich -neki make-CHR103),tower bolts and any miscellaneous hardware items.
a 2'-6" HIGH IN LAMINATE FINISH S.F.T
b 2'-6" IN VENEER FINISH S.F.T
c 4'-0" HIGH IN LAMINATE FINISH S.F.T
2 FULL HT. STORAGE IN PANTRY S.FT. 52
Providing and fixing storage units of full height as per drwng. They shall consist of 18mm thk.BWP. ply top, sides,back, bottom,
shelves and shutters. The bottom of the storages shall be at 3” from FFL. The top of storages shall touch the false ceiling level
or 7'-0" ht. The shutter with box type higes of approved make & steam beach lipping finished with melamine with approved
laminate on all the shutter edges. Division of the shutters shall be made equally according to the length of the storages ( as
approved by Bank/ architect). All the external surfaces shall be finished with 1.0mm thk. Laminate (suede finish) of approved
make.
18mm thk. BWP. Ply shelves removable type supported on side steam beach wood battens on both sides at 16” interval (
approximately / divided equally) shall be provided. All inner surfaces shall be finished with laminate including the shutters.
Rate shall be inclusive of all necessary approved fittings like hinges, locks, 150mm long SS brushed finish handles,tower bolts,
locks and any necessary hardware items. The top ply edge should be fitted with 19mm x 7mm size steam beach moulding
finished with melamine.
3 OVERHEAD STORAGE IN PANTRY AND AT HRM, DM & RMCR SECTION S.FT. 90
Providing and fixing over-head storages which consist of 18mm thk. BWP. ply shutter with box type higes of approved make &
Steam beach lipping with approved laminate on all the edges. The shutter should be made of of 18mm thk. BWP. Ply top,
sides, rear and bottom. All the external surfaces shall be finished with 1.0mm thk. Laminate (suede finish) of approved make.

Division of the shutters shall be made equally according to the length of the storage. The edges of the shutters shall be
provided with steam beach lipping. One Ply shelf of 18mm thick BWP.ply removable type supported on side steam beach
wood battens on both sides (divided equally) shall be provided. All inner surfaces shall be finished with laminate including the
shutters.. Rate shall be inclusive of all necessary approved fittings like box type hinges, locks, tower bolts, 100mm SS Brush
finished handle etc.
4 SHUTTERS BELOW GRANITE COUNTERS IN PANTRY S.FT. 48
Providing and fixing 19mm thk. BWR ply shutters with ply frame, skirting gap as shown in the drg. shall be maintained. Division
of shutters shall be made equally according to the length of the counter.
Shutters shall be hinged to the framework and finished with 1.0mm thk. Laminate (suede finish) of approved shade from
outside, applied with approved oil paint from the inside and edges of shutters with steam beach lipping. Rate shall be
inclusive of all necessary approved fittings like hinges, ball catch, handle, and any necessary hardware items.
5 SIDE / CORNER TABLES
Providing and making corner / side tables of above mentioned size as per drwng. Table top shall consist of 12 mm. Thk.float
glass with champhered edge( bevelled edge) fitted to the frames with necessary arrangement. The base shall be made up of
Steam beach wood frame as directed by the the Architect. It should be with 4 Nos of 35mmx35mm for vertical members tied
to each other with horizontal members of 20mm x 35mm frames at bottom and All wooden frames to be finished with
melamine.
a. CORNER TABLES(1'-6" x 1'-6" x 1'-6"HT.) NOS. 8
b. CENTER TABLES (1'-6" X 2'-6" X 1'-6"HT) NOS. 4
6 PIN-UP BOARDS S.FT. 216
Providing and fixing pinup boards. It consist 12mm thick soft boards of good density to be mounted over 12mm thick BWP. ply.
The soft board will be covered with a plain fabric (appox Rs.250 /Rmts. of Dark Blue Colour) from front and edges. Suitable
steam beach moulding 25mm x 25mm size to be fixed on all four sides and will be finished in melamine polish.
Note : Only soft bords provided on other than the partitions will be measured and soft board made in the partitions will be the
part of the partition measurement (rate) and not consider separately.
7 CONFERENCE TABLE AND VIDEO-CONFERENCE TABLE
Providing and making a table of over all size of top as mentioned above. It shall consist of 18mm thk. BWP. Ply top as per
design finished with 6mm thk Corian of Merino Hanex Solid Surface of approved shade and colour, supported on 8-12 nos
numbers of mullion boxes, as per design of size 18" x 10" made of 18mm thk. BWP finished with 1mm thk laminate of
approved shade and Ply inter connected with boxing 10" x 6" (as approved by the architect) on top(below table top ) and at
bottom (on floor level), finished in laminate of approved shade. Table top to be finished with 6 mm thk Corian of Merino make-
Hanex Solid Surface of approved shade and colour and other external surfaces with 1.0 mm thk laminate of approved
shade.This supporting boxes shall be then covered with apron on all sides as per design with 19 mm thk plywood finished with
approved shade of laminate. Additional legs/ supports in 19 mm thk BWP Ply and finished with approved shade of laminates to
be provided at distances as mentioned in the detailed drawings and as per the direction of the architect/ Engineer-in- charge
a. 56 SEATER CONFERENCE ROOM TABLE - (5' x 27'-0") with Corian Table Top as per Design NOS. 1
b 15 SEATER VIDEO CONFERENCE TABLE IN V SHAPE- (6'-0" AVG x 18'-0" AVG.) with Corian Table Top as per Design NOS. 1

8 DISCUSSION TABLE - (2'-0" READIUS X 2'6"HT) NOS. 0

Providing and making a table of over all size of top as mentioned above. It shall consist of ¾” thk. BWP. Ply top as per design
(double edge on outer edge with 1 1/2" thk half round moulding on the edges) supported on ¾” thk. BWP. Ply
verticals.supported on wooden base (as designed by the architect). Suitable wooden moulding as architect design with
mellamine shall be provided to the edge of the top. All external surfaces to be finished in 1.5 mm laminate.
9 MARKETING DESK - (8' X2'6") with Corian Top
Providing and making a table of over all size of top as mentioned above and as per design given. It shall consist of 18mm thk.
BWP. Ply top finished with 6mm thk Corian of approved shade and make of MERINO Make with edge moulding and a 3
drawer unit with locks, handles etc. on the end of the table as shown in the drawing.(as approved by the architect). The drawer
unit finished top should be at a lower level of 25mm below the finished counter top. The front modesty panel shuould be
finished 18 mm BWP. ply with laminate ( as approved colour / shade) with Metallic laminate. The customer side top should be
at a height of 1 feet with 18mm thick ply above which GALAXY MARBLE (Engg.Marble) of approved colour to be provided. The
a. inside
IN of drawer
CORIAN units, and
& LAMINATE the tables should be finished with laminate of approved shade.
FINISH NOS. 2

10 TABLES
RUNNING COUNTER (1'-6" WIDE) IN DESPATCH AREA R.FT. 6
a Providing and laying a Plain running counter with Pencil Drawers at every 3'-0" length for over all size of top as mentioned
bellow. It shall consist of 3/4” thk. BWP. Ply top as per design (double edge on the front and back with 1 1/2" thk half round
moulding on the edges) supported on ¾” thk. BWP. Ply verticals at every 3' length. Suitable (as per Architects design) wooden
moulding with mellamine shall be provided to the edge of the top. The top of the counter should be finished with 1.0 mm
Laminate and all other external surfaces to be finished in 1.0 mm. Thk. Laminate (suede finish)of approved make.
11 SHUTTERS WITH FRAME FOR ELECTRICAL PANELS S.FT. 38
Providing and fixing 18mm thk. Com ply shutters with same ply frame. Division of shutters shall be made equally according to
the length. Shutters shall be hinged to the framework and finished with 1.0mm thk. Laminate of approved colour and shade on
outer side and inside finised with 2 coats of enamel paint of app colour and shade. Rate shall be inclusive of all necessary
approved fittings like hinges, ball catch,150 mm long SS Brush Finish handle, tower bolts, locks, Aluminium powder coated air
vent grills and necessary hardware fitings complete, etc.,
12 KEY BOX NOS. 4
Providing and fixing key box of size 1' 6"x1' 6"x 6" with all sides and back with 18mm thick BWP. Ply wood and lockable glass
shutters in 18mm ply , with 5 mm glass. Necessary hooks to be provided inside the box. All exposed areas and inside to be
finished with 1 mm thick laminate of approved shade. The edges of shutter and box to be lipped with steam beach beeding
polished with melamine. Rate shall be inclusive of all necessary approved fittings like hinges, locks, hooks etc. and any
necessary hardware items.
13 A.C.TRAP DOORS WITH LAMINATE FINISH S.FT.
Providing and fixing A.C. Trap doors of above mentioned sizes consisting of 19mm thk. BWR ply shutters. The pair of shutters
shall be with MILKY WHITE 1 mm laminate on both sides fitted in frame of 2” x 1 ½” Sal wood sections finished with enamel
paint to match with the ceiling. The frame need to be suppoted from the ceiling as per directions of Bank/ Architect. Rate shall
be inclusive of necessary fittings like hinges ( Heavy Duty type), tower bolts, locks, etc.
14 BOXING FOR ROLLING SHUTTER
a. WITH LAMINATE FINISH S.FT 72
Providing & fixing ¾” BWR ply boxing for the rolling shutters. Necessary wooden framing shall be provided. The boxing shall be
finished on all exposed sides by 1mm laminate and internally with enamel paint.
Note : rate shall include all necessary hardware fittings, etc.
b. PLY BOXING S.FT 48
Providing & Fixing ¾” BWR ply boxing for the rolling shutters / separation for boxing with out laminate finish above false celing
painted with Enamel paint. Necessary framing shall be provided.
15 TRAP DOOR FOR ROLLING SHUTTERS WITH LAMINATE S.FT 33
Providing and fixing trap doors consisting of 1/2” thk. BWP. ply shutters with a clear opening of 4.5" opening for smooth
operation of shutters and rest is closed with mirror screws (for opening for servicing). The shutters shall be finished with
approved 1mm laminate, frame of 2” x 1 ½” wood sections shall be provided for proper support and strength. Rate shall be
inclusive of necessary fittings like hinges of approved make make), ball catches, tower bolts, etc.
16 FALSE CEILING IN PLY WITH PAINT FINISH ( PAINTING WILL BE MEASURED SEPARATELY) S.FT. 120
Providing and fixing 12mm ply with necessary support from ceiling of 2”x2” Sal wood members provided at 2’-0” c/c and
finished with paint of approved shade, with necessary primer etc. as per the approved design. ( Painting will be measured
separately)
17 FALSE CEILING IN PLYWOOD FINISH S.FT. 228
Providing and fixing wooden ceiling with 12mm ply and necessary support from ceiling of 2”x1” Sal wood members provided
at 2’-0” c/c as per design and as directed by the Engineer-in-charge/ architect
18 FALSE CEILING IN PLY WITH VENEER IN MELLAMINE POLISH S.FT. 102
Providing and fixing 12mm ply with necessary support from ceiling of 2”x1” Sal wood members provided at 2’-0” c/c and
finished in veneer with mellamine polishof approved shade.
19 PEGEON HOLE SHELVES FOR DESPATCH ROOM S.FT. 50
Providing and fixing Pegeon Hole units of full height and 1'6" depth as per drwng. They shall be made of 18mm thk.BWP. ply
for both verticals and horizontal members. The bottom of the unit shall be at 3” from FFL. The top of storages shall touch the
false ceiling level or 7'-0" ht. The facing edges of all ply wood sections should be provided with steam beach lipping finished
with melamine with approved laminate on all the shutter edges. The size of pegeon hole to be adjusted equally as per the site
condition. Approximate size of each pegeon hole should be 10" x 10" as per drawings and in consultation with Architect. All
the Internal surfaces shall be finished with 1.0mm thk. Laminate (suede finish) of approved make.
E FALSE CEILING AND POP WORKS
1 FALSE CEILING - GYP BOARD S.FT. 4350
Providing and fixing ½” thk. Gypsum India board false ceiling at levels as shown in the drg. From FFL. Rate shall be inclusive of
all Gypsum India components contained G.I. perimeter channels of size 0.55 thick having one flange of 20mm and another
flange of 30mm and a web of 27mm alongwith perimeter of ceiling, screw fixed to brickwall/partition with the help of nylon
sleeves and screws, at 610mm centres. The suspending G.I.intermediate channels of size 45mm, 0.9mm thick with two flanges
of 15mm each from the soffite at 1220mm centres with ceiling angle of width 25mm x 10mm x 0.55 thick fixed to soffite with
G.I. cleat and steel expansion fastners at every 610mm c/c. Ceiling sections of 0.55mm thickness having knurled web of
51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to intermediate channel with the help of
connecting clip and in direction perpendicular to the intermediate channel at 457mm centres. 12.5mm tapered edge Gypboard
is then screw fixed to ceiling section with 25mm drywall screws driver or drilling machine with suitable attachment.
The boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square
edge of the boards with jointing compound & joint paper tape. Rate shall be inclusive of Cut outs for A/c machiness, spot
lights, light fixtures, A/C. Grills, fire and security systems cut outs, All Sections should adhere to the manufacturers guidelines.
Vertical sides visible will be measured.
2 WALL PUTTY S.FT. 9000
Providing and applying Wall Putty on walls and columns (average 12mm thk). The rate shall include scrapping, levelling and
preparing the surface. The rate shall be inclusive of all types of grooves above the skirting, around the window and door
frames. If the average thickness is found to 8mm~6mm or less, then Wall Putty will be considered as pulti finish - at the rate of -
3 50%
POP the quotedFOR
PUNNING rateGYPSUM
(Make: Birla / Asian / Berger)
CEILING S.FT. 4800
Providing and applying POP Punning on Gypsum Ciling (average 6mm thk). The rate shall include scrapping, levelling and
preparing the surface. The rate shall include scrapping, levelling and preparing the surface. The rate shall be inclusive of all
types of grooves above the skirting, around the windows and door frames. If the average thickness is found to be 4mm or less
than POP will be considered as a putti finish and the rate shall be 50% of the quoted rate

4 MODULAR FALSE CEILING - ARMSTRONG / equivalent make S.FT. 3730

Providing and fixing Armstrong (Fine Fissured Micro Look with Tagular Edge using 15mm Grid sections) false ceiling of size
24”x24” at levels as shown in the drwng. from FFL. Rate shall be inclusive of providing the total system with installation etc..
The contractor has to maintain all tiles in good order and replace the defected tiles (at his own cost) before handing over the
site for Branch Operations (till Inauguration).
5 Acoustic
ProvidingCeiling TilesAcoustic
and Fixing in Conference
tiles of &
15Video Conference
mm thickness androom
tegular edge, easily demountable tile, manufactured from High S.FT. 684
density glass wool, with the visible surface batch painted glass tissue in white and the back of the tile should be covered with
glass tissue. The glass wool core of the tiles should be tested and classified as noncombustible according to prEN ISO 1182. The
system should have Sound Absorption NRC value of 0.9 (according to ASTM C 423). Tiles should withstand a permanent
ambient RH Upto 95% at 30*C without sagging, warping or delaminating (ISO 4611). The light reflectance of the tiles should
not be less than 83%. Tiles certified by the indoor climate labeling and reBWPended by Swedish asthama and allergy
association and granted Nordic Swan eco–label and fully recyclable. The glass wool core of the tiles should be tested and
classified as non combustible according to EN ISO 1182 and the ceilings should fall under Class A2 –s1 d0 according to EN
13501- 1

F PAINTING WORKS
1 PLASTIC EMULSION S.FT. 9000
Providing & applying plastic emulsion paint on walls, columns & ceilings. The rate shall include scrapping, levelling & preparing
the surface. Primer coat + (minimum) 3 coats to get evenly spread quality finish (roller finish) of approved make , quality &
finish shall be provided.
2 LUSTRE PAINT IN GYPSUM FALSE CEILING S.FT. 4800
 Providing & applying Luster Paint on walls, columns & ceilings. The rate shall include scrapping, levelling & preparing the
surface. Primer coat + (minimum) 3 coats to get evenly spread quality finish (roller finish) of approved make, quality & shade
shall be provided.
3 DUCO PAINT S.FT.
Providing & applying duco paint of approved make, quality & shade as per the architects direction on wooden or metal
surfaces. The rate shall include scrapping, levelling & preparing the surface, primer coat
4 ENAMEL PAINT IN ROLLING SHUTTER S.FT.
Providing & applying 1st quality oil paint of approved make, quality & shade. The rate shall include scrapping, levelling &
preparing the surface with primer quote.
5 TEXTURED FINISH IN RECEPTION AREA S.FT. 188
Providing & applying a coat of textured finish on walls and columns. The rate shall include scrapping, levelling & preparing the
surface. Primer coat + (minimum) 3 coats of approved make, quality & shade shall be provided.
G MISC. ITEMS
1 ROLLER BLINDS, VERTICAL BLINDS, FILM etc. S.FT. 1020
Vertical Blinds
Supplying and fixing Vertical Blinds of approved make and shade Headrail : The head channel shall measure 44mm wide and
25mm deep, with a nominal wall thickness of 1.0mm, extruded from 6063-T5 aluminium alloy, finished in clear anodising. The
front profile is curved giving it a sleek and modern look. Spline Shaft : The spline shaft is a tri-lobular aluminium extrusion of
6063-T5 alloy, with sliding engagement to the slat traveller worm clutches, enabling all travellers to be tilted simultaneously.
Slat Traveller : Shall be moulded in a high engineering grade plastic and shall incorporate a worm gear clutch designed to
prevent damage to the assembly when overloaded and to assist in slat hook synchronisation. Slat Spacers : Shall be press
formed from series / range 0.2mm x 5mm stainless (DIN 17224) and shall couple the slat travellers to each other, ensuring
each slat traveller to traveller distance is evenly spaced.
Tilt Control : Shall be by means of 2.0mm braided nylon cord held in tension by a cord weight and by pulling on a control chain
connected to a pulley. Vanes : The vanes shall be 89mm, 100mm or 127mm wide as appropriate and made of crowned pre-
painted aluminium or of woven and non-woven fabrics. Fabric vanes shall be provided with bottom pockets housing bottom
weights which are coupled together by means of bead chains pivotally attached by clasps to each side of each weight. Bottom
Linkage : The bottom linkage shall couple adjacent slats at the base to minimise differential movement of vanes. Bottom
Weight : Shall be of moulded PVC compound, housed in sewn bottom pockets of fabric vanes to hold the vanes taut, and are
provided with pivot, pins for attachment of the bottom linkage.
Mounting /Extension Brackets : Shall be press formed angle bracket ribbed for stiffness and provided with holes for fixing
screws and slotted holes for screw and nut attachment of the channel mounting clips. Clip in Bracket : Shall be of hardened
tempered spring steel, press formed to accept the head channel with a snap in action. Slat Carrier : Shall be of moulded nylon
and shall be suitable for snap insertion into the hook of the slat traveller.
TWILIGHT CLOUD WHITE BLACKOUT BLINDS of HUNTER DOUGLASS make
2 3M SYNTHETIC DOOR MATS (4'-0" x 2'-0") NOS. 8
Providing & laying in place Synthetic Door Mats (3M) of sizes not less that 4' x 2').
3 POSTERS & DANGLERS NOS. 56
Providing & Fixing the Poster Holders & Danglers (Supplied by the Banks Vendor) as directed by the Bank Staff / Architect on
the walls/ panels / glazing etc. complete in all respect with-out spoiling the décor
4 Frosting film/Sun control film
I FROSTING FILM S.FT. 480
Providing and fixing Non-reflective matte, frosted, scratch resistent, high performance resin coated polyster film with required
frosting pattern on the glass surface complete as per the directions of EIC/ Architect (Payment shall be made for the finished
area of the film actually provided. No deduction shall be made for openings upto 0.1 Sq.m. area each and nothing shall be paid
extra for making such openings.)
II Sun Control Film S.FT. 1280
Providing and fixing in position Sun control film of approved make and shade with required frosting pattern on the glass
surface complete as per the directions of EIC/ Architect (Payment shall be made for the finished area of the film actually
provided. No deduction shall be made for openings upto 0.1 Sq.m. area each and mnothing shall be paid extra for making such
openings.)
Garware make - Grey 5
3M - CRYSTAL GLASS FINISHES 7725 SE325
5 M.S. SLOTTED ANGLE STORAGE S.FT. 210
Providing and making M.S. slotted angle storage using angles of 18 gauge thickness and shelves of 20 gauge designed as per
the specfications of standard manufacturers. Shelves shall be provided at 1’-6” c/c & supported on frames on all four sides
with vertical supports as per manufacturers' standard specifications.

6 WOODENand
Providing FLOORING AT DGM'S
fixing minimum CHAMBER
11mm thick AC VI grade laminated wooden flooring suitable for BWP-heavy use areas like S.FT. 450
auditorium application of approved make, shade and pattern. The top surface shall have a 0.60 mm thick multi layer high
pressure laminate fixed over moisture resistant high density fiberboard substrate. The planks shall be of size 1200 mm x
200/125 mm. The flooring shall confirm to EN 438, EN 717-1, EN 13501-1, EN-1815, JIS Z 2801:2000 standards. The planks shall
be placed on an underlay of 0.2 mm thick alkali resistant Polyethylene sheet having density 920-935 kg/ m3 to resist moisture
from the sub floor and to secure the floor installation etc all complete. (Skirting profiles, trims etc shall be included & not paid
extra) as per direction of E-I-C.
7 ANTI STATIC LUXURY WOVEN CARPET FLOORING AT CONFERENCE AND VIDEO CONFERENCE ROOM S.FT. 990
Providing supplying and fixing 2.5MM -2.8MM thick, Sound Absorbent, Anti Becterial, Stain, Water and Oil Resistant, Higenic
and Easily Installable, LUXURY WOVEN VINYL FLOORING suitable for Office,Corporates and Public area having overall length of
20-25 metres and Roll width of 1.80 m, having basic rates Rs 155-180sft, of shade as mentioned below- Conference/FAO-
NATURAL SOUL, Recepion/passage and other area- NATURAL CORAL & NATURAL BLACK( Special design below reception table
as heighliters only) on the existing floor with proper adhessive. The rate to include preparation of sub-floor to even surface
including all materials, labour, transportation , adhessive, fixing all complete as per the direction of the engineer incharge
8 MAGNETIC
Providing andWHITE
fixingBOARD
of magnetic white board of approved make scratch resistant matt finish P3 surface consisting of ceramic
steel of thickness 0.55mm to 0.65 mm, having a weight of 3-4 kgs per sqm. The core material shall be of interior grade 9mm
thickness with density 700 to 800 kg/cum. With a backing of galvanized steel of 0.25 mm thickness having approximate weight
of 1.96 kgs/sqm. This entire assembly shall be housed in an anodized aluminum extruded section conforming to IS-6477 and IS-
3965/2673 and corners of moulded ABS. The front and back surface will be affixed with 10-15 micron silver matt satin finish.
This should be provided with clamp for hanging arrangement with locking facility including one set of accessories comprising of
magnets, magnetic dry markers and magnetic
i 4’ x 10’ (1200mm x 3000mm) NOS 1
ii 4’ x 6’ (1200mm x 1800mm) NOS 1
iii 3' x 4' (900mm x 1200mm) NOS 2
9 COLOURED ACRYLIC SHEET LOGO FO THE BANK, BACK LIT
Supplying , fabricating and installation of Canara Bank's Logo of 2 Nos of Triangle (Blue and Yellow Colour) made of coloured
acrylic sheet 5-6mm thk in box section, and as per the sizes as mentioned in the detailed drawings . This Coloured Acrylic sheet
box logo should be fixed with strip light fitted from inside , as per the direction of the architect.
i OVERALL SIZE 750MM X 750MM NOS 1
ii OVERALL ZIZE 450MM X 450 MM NOS 1
10 Wallpaper
Providing and fixing in position Wallpaper fixed with approved make of adhessive of approved Make and Design as Specified by SFT 120
the Architect

GRAND TOTAL
 ESTIMATED BOQ FOR ELECTRICAL WORKS OF CIRCLE OFFICE AT SIX MILE, GUWAHATI, ASSAM
Sl. No Description Unit Qty Rate Amount
SECTION-A
I MAIN LT PANEL
Supplying and installation of metal enclosed wall/ floor mounted front operated cubical type switch gear panel
suitable for indoor installation conforming to IS: 8623 (Part I & II). Panel should be made of sheet steel and
thickness not less than 2mm and structural steel having light section. The panel shall be completely dust tight
and vermin proof and shall be painted with anti corrosive and anti condensation type two coats of primer and
1.1 two coats of paint. All wiring shall be PVC insulated and PVC sheathed of 1100 volt grade of required size. The
panel should have provision of entry of cable at the bottom and also provision of out going feeders from the
bottom of the panel. The panel shall incorporated double busbar system. The bus bar shall be of high quality
copper of uniform cross section. The panel shall consist of the following items (viz. voltmeter, ammeter, CT,
indicating lamps, selector switch etc.) connected as per drawing and shall be flush mounted on the front of the
a Incomer :- 400A 4P 36KA MCCB - 1 No
b Outgoings :-
160A 4P 25KA MCCB - 1 No.
100A 4P 25KA MCCB - 4 Nos.
63A 4P 25KA MCCB - 1 No.
63A 4P MCB - 1 No.
40A 4P MCB - 5 Nos.
32A 4P MCB - 3 Nos.
c 1 no., 0-400A, Ammeter with CTand selector switch
d 1no., 0-500V, Voltmeter with selector switch and fuse
e 1Set, TPN, Copper busbars of size 40mm x 10mm thk PVC insulated suitable for 640 Amp load
f 1 Set, RYB, indicating lamps with resistors and fuses
Full Set as above Set 1
2 LT PANEL-UPS
Supplying and installation of metal enclosed wall/ floor mounted front operated cubical type switch gear panel
suitable for indoor installation conforming to IS: 8623 (Part I & II). Panel should be made of sheet steel and
thickness not less than 2mm and structural steel having light section. The panel shall be completely dust tight
and vermin proof and shall be painted with anti corrosive and anti condensation type two coats of primer and
2.1 two coats of paint. All wiring shall be PVC insulated and PVC sheathed of 1100 volt grade of required size. The
panel should have provision of entry of cable at the bottom and also provision of out going feeders from the
bottom of the panel. The panel shall incorporated double busbar system. The bus bar shall be of high quality
copper of uniform cross section. The panel shall consist of the following items (viz. voltmeter, ammeter, CT,
indicating lamps, selector switch etc.) connected as per drawing and shall be flush mounted on the front of the
a Incomer :- 100A 4P MCCB - 2 Nos. with Interlock Change Over System.
b Outgoings :-
40A 4P MCCB - 4 Nos.
32A DP MCCB - 3 Nos.
c 1 no., 0-100A, Ammeter with CTand selector switch
d 1no., 0-500V, Voltmeter with selector switch and fuse
e 1Set, TPN, Copper busbars of size 35mm x 5mm thk PVC insulated suitable for 250 Amp load
f 1 Set, RYB, indicating lamps with resistors and fuses
Full Set as above Set 1

3 AUTOMATIC POWER FACTOR CONTROL PANEL

Supply and installation of 60 KVAR APFC panel, floor/wall mounted front operated totally enclosed vermin
3.1 proof, indoor non-drawout-cubicle type power panel fabricated out of 2mm thk CRCA sheet having gasketed
hinged cover on each cubicle fully powder coated with following acessories
a 1No.160A,FP, MCCB as incomer
b 2 nos. of 50A 3P contactor & 1 no. 25A 3P contactor
c 2 nos. 40A TP MCB & 2 nos. 25A TP MCB
d 2 nos. 20KVAR & 1no. 10 KVAR Capacitor
e Suitable bus bar for connecting the contactors and MCB's, Capacitors
f 1 no. 4 step APFC relay suitable for above arrangement
g ON/OFF/TRIP push button for each capacitor
h ON/OFF/TRIP indication lamp for each capacitor
i 1 Set, RYB, indicating lamps with resistors and fuses for incomer.
Full Set as above SET 1

SECTION-B
4 CHANGE OVER
Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20
protection powder painted sheet steel enclosure fitted on angle iron frame of the following capacity complete
with making necessary connection as approved, specified and directed by the deptt.
C&S, Havells, Indo Asian, HPL, GECO make)
a) 400A Each 1
S & I of SPN D/D consumer Unit with 8 ways with suitable DP incomer and SP out going MCB's for Signage
5 Nos
Lighting.
6 MAIN SWITCH
Supply and fixing of following MCCB Unt with MCCB in sheet steel enclosure on M.S. angle frame / M.S. legs
on wall complete with interconnection, mending good damages to original finish, painting, etc. as required.

a) 400A 4P 36KA MCCB Each 1

7 MCB DISTRIBUTION BOARD
Supplying, installation, testing and commissioning of surface/recess mounting, 220/415 volts prewired MCB
distribution boards with all switchgears as specified below, of sheet steel, dust protected, duly phosphatized
and powder painted, inclusive of 200 amps tinned uniformly rated electrolytic copper bus-bar, common
neutral link, earth bar, din bar for mounting MCB/MCCB/RCCBs detachable gland/knock out plates and with
built in loose wire box, and superior make terminal connectors for all incoming and outgoings circuits, duly
prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/neutral link
and ready for installation as specified below:

ARCHIVENTIONS- Architects Engineers, R.G.Baruah Road, Guwahati, Assam

 7.1 MAIN TPDB [VTPN] [MCBDBP-1F, MCBDBP-2F & MCBDBP-3F forPower &A/C]
8way VTPN TPN DB IP 43 IK 09 with metal Doors - 1 No. No.s 3
Incomer
100A 4P 25KA MCCB - 1 No.
Outgoing
25A TP 10 KA MCB - 5Nos.
20A/25A SP 10 KA MCB - 5Nos.
10A/16A SP 10 KA MCB - 4Nos.
7.2 MAIN TPDB [VTPN] [MCBDBP-1S forPower &A/C]
8way VTPN TPN DB IP 43 IK 09 with metal Doors - 1 No. No.s 1
Incomer
63A 4P 25KA MCCB - 1 No.
Outgoing
25A TP 10 KA MCB - 2Nos.
20A/25A SP 10 KA MCB - 6Nos.
10A/16A SP 10 KA MCB - 12Nos.
7.3 MCBDBL-1F, MCBDBL-2F & for LIGHT & RAW POWER No.s 2
8way TPN DB IP 43 IK 09 with metal Doors - 1 No.
Incomer
40A 4P MCB - 1 No.
40A 4P RCCB 100mA/300 mA sensitivity - 1 no.
Outgoing
6A SP 10 KA MCB - 15Nos.
10A SP 10 KA MCB - 9Nos.
7.4 MCBDB 12 way SPN DB - MCBDBL-1S for LIGHT & FAN No.s 2
12way SPN DB IP 42 IK 09 with metal Door - 1 No.
Incomer
40A DP MCB - 1 No.
Outgoing
40A DP RCCB 100mA/30 mA sensitivity - 1 no.
6A SP 10 KA MCB - 8 Nos.
7.5 MCBDB/UPS-1F, MCBDBUPS-2F & for UPS POWER No.s 2
8way TPN DB IP 43 IK 09 with metal Doors - 1 No.
Incomer
40A 4P MCB - 1 No.
40A 4P RCCB 100mA/30 mA sensitivity with nuisance protection - 1 no.
Outgoing
10A SP 10 KA MCB - 24Nos.
7.6 MCBDB/UPS-1S for UPS POWER No.s 1
12way SPN DB IP 42 IK 09 with metal Door - 1 No.
Incomer
40A DP MCB - 1 No.
Outgoing
40A 4P RCCB 100mA/30 mA sensitivity with nuisance protection - 1 no.
10A SP 10 KA MCB - 8 Nos.
7.7 MCBDB/UPS-SERVER & MCBDB-E for UPS POWER & EMERGENCY LIGHT No.s 2
8way SPN DB IP 42 IK 09 with metal Door - 1 No.
Incomer
32A DP MCB - 1 No.
Outgoing
25A 4P RCCB 100mA/30 mA sensitivity with nuisance protection - 1 no.
10A SP 10 KA MCB - 4 Nos.
7.8 4 Pole One way enclosure with 25A TP 10 KA MCB No.s 19
7.9 2 Pole One way enclosure with 20A/25A/32A DP 10 KA MCB No.s 14
SECTION-C
8 CABELS / MAINS
S & I of 1100V grade armoured cable having sector / circular shaped aluminium / copper conductor PVC
insulated cores, laid up, PVC tape wrapped inner sheathed, GI strip / wire armoured and overall extruded PVC
8.1 sheathed confirming to IS: 1554, laid on wall or ceiling using GI clamps and spacers as per route shown at site
and further as directed by Bank / Architect in the following sizes. Rates shall be complete with complete with
cable (Havell's/Richa/RR kebel or equivalent) glands and two nos. of 8SWG GI wire
a 3 1/2 C X 185 Sq.mm Aluminium Mtrs 90
b 3 1/2 C X 70 Sq.mm Aluminium Mtrs 85
8.2 Sub-main line:-
Wiring in MS conduit of IS specification of Proper size with core PVC insulated stranded copper wire 11KV
grade (Finolex/Havell's/Richa/RR kebel or equivalent) and with all materials supply ,installation connection
complete as per circuit diagram and as required from main DB to various DBs:-
a) With 4 Nos. x 16 + 2X16 sq. mm (2ECC) Mtrs 35
b) With 4 Nos. x 10 + 2X10sq. Mm (2ECC) Mtrs 75
b) With 4 Nos. x 6 + 2X6sq. Mm (2ECC) Mtrs 270
8.3 Sub-main line:-
Wiring in MS conduit of IS specification of Proper size with core PVC insulated stranded copper wire 11KV
grade (Finolex/Havell's/Richa/RR kebel or equivalent) and with all materials supply ,installation connection
complete as per circuit diagram and as required from main DB to various DBs:-
a) with 3nos 4sq.mm (1ECC) Mtrs 100
b) with 3nos 6sq.mm (1ECC) Mtrs 480
c) with 3nos 10sq.mm (1ECC) Mtrs 60
9 POINT WIRING
Supply & Installation of concealed point wiring using 600v grade 2.5 sqmm copper conductor PVC insulated
wires (with proper R,Y,B color code ) pulled through haevy gauge PVC conduits laid concealed over false ceiling
9.1 or in wall chases including circuit wires from the relevant DB and also including 1.5 Sq.mm Green Colour
Copper earth wire and provision of grid plate type ( ROMA) switches and sockets as approved by Bank /
Architect. Each circuit feeding not more than 8 points / 800 W as per the following configuration.
a Primary light points including the cost of 6A switch Pts 190
b Secondary light points looped from the above point Pts 94

ARCHIVENTIONS- Architects Engineers, R.G.Baruah Road, Guwahati, Assam

 c 6A plug point as primary point. [SO] Pts 6
d Secondary 6A Plug point on switch board. [SO] Pts 8
e 16A Plug Point directly taken from DB for hotplate/geyser / zerox / fridge [P] Pts 6
Indicator Light point from main panel to Banking area for indication of Mains power supply with wiring,
f Pnt. 1
indicator lamps etc.
g Exhaust fan/ Wall Fan point consisting of 6A socket near fan and switch on light switch board Pts 61
h Ceiling fan point with electronic regulator (2 module step, 100 watt ( min.) Pts 5
Wiring for Signages with 2R x2.5 Sq.mm and 1 Rx 1.5 Sq.mm, PVC insulated copper conductor flexible cable to
i be connected to the SPN D/D consumer along with a Timer and Contactor unit installed in Electrical Room Set 2
room
9.2 COMPUTER/ RAW POWER WIRING
Note- All sockets should be placed below the workstations as mentioned in the drawings but the controlling
switch should fixed above the work stations and at place as directed by the architect
S & I of point wiring for UPS or stabilized power plug points on workstations / table for computers using 3C X
2.5 Sqmm Cu. PVC sheathed white color flexible cable pulled through already laid floor raceways and taken
upto table top using PVC rigid or flexible conduits run within wooden or metal partitions. Each point consisting
a Pts 9
of 3 Nos of 6A/16A 2 / 3 Pin sockets and 1 No 16A switch, wired together forming one point. Switches and
sockets to be (ROMA). Earth wire to be of Green colour only. ( Only 2 tables served by one circuit from UPS
SDB).
& I[SOC]
of point wiring for UPS or stabilized power plug points on workstations / table for computers using 3C X
2.5 Sqmm Cu. PVC sheathed white color flexible cable pulled through above False ceiling and cutting the walls
as raceways are not provided and taken upto table top using PVC rigid or flexible conduits run within wooden
b or metal partitions. Each point consisting of 3 Nos of 6A/16A 2 / 3 Pin sockets and 1 No 16A switch, wired Pts 80
together forming one point. Switches and sockets to be (ROMA). Earth wire to be of Green colour only. ( Only
2 tables served by one circuit from UPS DB) Cost is inclusive of necessary cutting the walls and including PVC
Pipe required for taking the wires. [SOC]
c S & I of points similar to above but to be used as raw power point on the tables consisting of one 6A/16A Pts 4
socket with switch of other color and flexible cable of black color & circuit taken from LIghting DB ( 4 tables
served by one circuit from LDB/PDB) Taken through Raceways. [SOR]
d S & I of points similar to above but to be used as raw power point on the tables consisting of one 6/16A socket Pts 46
with switch of other color and flexible cable of black color & circuit taken from LIghting DB ( 4 tables served by
one circuit from LDB/PDB) Taken Above False ceiling and through walls as raceways are not provided. Cost is
inclusive of necessary cutting the walls and including PVC Pipe required for taking the wires.
SECTION-D
10 EARTHING
10.1 Earthing with Copper earth plate 600 x 600 x 3 mm thick including accessories, and providing masonary
enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc with charcoal/ Each 4
coke and salt as required.
10.2 Earthing with GI earth plate 600x600x3mmthick including accessories, and providingmasonary enclosure with
cover plate having locking arrangement and watering pipe of 2.7 meter long etc with charcoal/ coke and salt Each 2
as required.
10.3 Providing & fixing 25 mm x 5 mm Cu strip on surface or in recess for connection as required. Metres 40
10.4 Providing & fixing 25 mm x 5 mm G.I. strip on surface or in recess for connection as required. Metres 20
10.5 Providing & fixing 6 SWG dia GI wire on surface or in recess for loop earthing alongwith adjusting surface/ Metres 20
recessesed conduit / submain/ cable as required.

SECTION-E
11 LIGHTING FIXTURES(Philips/Jaquar or equivalent)
11.1 S & I of lighting fixtures as per the details given below including necessary hardware such as clamps,nuts, bolts,
nails, screws and suspension chains as required for fixing the fixtures in position as directed by architect /
Consultant.
DOWN LIGHT - Nero Round LED recess-mounted designer panel with aluminium die cast housing , Item Code-
a LNRO01R012XN, Wattage-12W, CCT- 4000 K, or equilivent as approved by the Engineer-incharge/ Architect. Each 42
[DL]
EMERGENCY LIGHT - Areva (Round) Low-depth, recess-mounted, sleek, round downlight with aluminium die
b cast housing & policarbonate diffuser, Item Code-LARV01R015XN , Wattage-15W, CCT- 4000 K, or equilivent as Each 27
approved by the Engineer-incharge/ Architect. [EL]
PANEL LIGHT - Sauver Ultra Slim LED Panel made from extruded aluminium housing frame (recess / pendant)
c 2ft x 2ft , Item Code- LSVR01S036XN , Wattage-36W, CCT- 4000 K, or equilivent as approved by the Engineer- Each 111
incharge/ Architect. [PL]
COB-DOWNLIGHT - Teny LED recess-mounted COB Spot light with aluminium housing (white Finish) , Item
d Code- LTNY01R002XW , Wattage-2W, CCT- 3000 K, or equilivent as approved by the Engineer-incharge/ Each 10
Architect. [COBL]
COB-DOWNLIGHT - Estus Swivel Downlight, Recess-mounted, COB-based, square tiltable LED doynlight with
e multiple beam angle (36 degree) , Item Code- LETS36s006XN , Wattage-6W, CCT- 4000 K, or equilivent as Each 18
approved by the Engineer-incharge/ Architect. [COBR]
Supply and fixing of LED Indoor Strip Light (24V DC) IP33-rated, suitable for indoor application with different
f colours and wattages in standard 5.0 M roll with drivers (Cat. no. LDRV01S048XX), remote etc and all Each 8
accessories all complete. Item Code- LSTP03X008XM , Wattage-40W, CCT- RGB K, or equilivent as approved by
the Engineer-incharge/ Architect. [SRL]
1200 MM TUBE LIGHT - LED batten tubes, Glaze LED Batten, High quality aluminium extruded with decorative
g end caps, Item Code-LGLZ01x020XN , Wattage-20W, CCT- 4000 K, or equilivent as approved by the Engineer- Each 30
incharge/ Architect. [TL]
600 MM TUBE LIGHT - LED batten tubes, Glaze LED Batten, High quality aluminium extruded with decorative
h end caps, Item Code-LGLZ01x010XN , Wattage-10W, CCT- 4000 K, or equilivent as approved by the Engineer- Each 14
incharge/ Architect. [FL]
SQUARE DOWNLIGHT -Neve Plus (Square) LED recess mounted square panel with aluminium die cast housing ,
i Item Code- LNEP01S006XN , Wattage-6W, CCT- 4000 K, or equilivent as approved by the Engineer-incharge/ Each 17
Architect. [SDL]
Designer Light - Trius- Uniquely designed, suspended, triangle-shaped with uniform light output in extruded
j aluminium with polycarbonate diffuser, Item Code- LTRS02T090XN , Wattage-90W, CCT- 4000 K, or equilivent Each 4
as approved by the Engineer-incharge/ Architect. [DN]
Decorative Pendent Light - Cooper Finishing Pendent Lamp-E-27 LED 5WX 1, Item Code- KCH-COP-
k Each 3
MD150031251C, or equilivent as approved by the Engineer-incharge/ Architect. [DPL]

ARCHIVENTIONS- Architects Engineers, R.G.Baruah Road, Guwahati, Assam

 l Floor Lamp - Chrome Finishing with Opal Glass Floor Lamp: E-27 LED 14 W x 1, Item Code- KPT-CHR- Each 4
ML49061A, or equilivent as approved by the Engineer-incharge/ Architect. [NL]
11.2 Supplying including fitting fixing of following star rated Plastic Blade, new 450 mm dia bracket/wall fan of
Ivory Colour , complete with all accessories of following sweeps with making necessary connection cable, as
approved by the Deptt.s etc. as required complete and as directed by the Department .
a) 450 mm sweep [WF] EACH 45
11.3 Supply and fixing of 10" - 12" PVC exhaust fans with louvers.[EF] EACH 16
11.4 Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all accessories like down
rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt.s etc.
as required complete and as directed by the Department [Without regulator]. (ORIENT PSPO make / Usha
make/ CROMPTON make/ATC/ V GAURD make)
a) 1200 mm sweep [F] EACH 5
12 WIRING FOR DATA AND VOICE OUTLETS
12.1 Supplying, laying and termination of 4 pair Copper solid, twisted pair G600 CAT--6 cables through specified
dia PVC conduits / raceways. Cables must meet and exceed category 6/ class E standards requirements in
ISO/IEC11801, CENELEC EN50173 & TIA 568-B2-1. and providing & terminating with RJ-45 (Krone make) with
face plates / I/O Ports in suitable modular / MS box from server / EPABX room to individual work stations and
terminating other end with RJ-45 connector including numbering with ferule. Note- Rates shall be all inclusive
as mentioned in the description above and the payment for the same item shall be made on the number of
a pointsfor
RJ-45 provided based( THROUGH
data points on the above
RACE description
WAYS) points 4
b RJ-45 for data
Providing points Cat
and laying ( THROUGH False ceiling
5 cable (Make: andfor
D-Link) wall)
voice through specified dia PVC conduits / raceways for points 78
12.2 voice and providing & terminating with RJ-11 (Krone make) with face plates / I/O Ports in suitable modular /
MS box from server / EPABX room to individual work stations and terminate the other end with RJ-11
connector or on a Crone module with numbering of each cable with Ferule. Note- Rates shall be all inclusive as
mentioned in the description above and the payment for the same item shall be made on the number of
points provided based on the above description
Note- All Voice outlet should be fixed above the work stations and at place as directed by the architect
a RJ-11 for Voice ( THROUGH RACEWAYS) points 3
b RJ-11 for Voice ( THROUGH FALSE CEILING AND WALL) points 44
12.3 Supplying, laying and fixing of PVC telephone flexible wire through specified dia PVC conduits / raceways of
following size:
a 20-pair mtr. 30
12.4 Cat 6 Jack Panel, 24 Port (DATA) No. 1
12.5 Cat 6 Jack Panel, 24 Port (VOICE) No. 1
12.6 19", 3U SS Rack Mount Recessed Frame for Voice Terminations No. 1
13 CCTV SYSTEM
SITC of fixed dome indoor Colour Varifocal Lens Camera having 0.20 lux level requirement in night mode with
the following components / sub assemblies as per specifications, complete with power supply unit, necessary
brackets for fixing in the false ceiling etc. as required.(The camera shall be UL/ EN/ FCC certified) a. 1/3"
13.1 Nos. 6
progressive scan CCD image sensor Day/Night camera with inbuilt DSP, advanced features like High resolution
of minimum 640 x 480, AGC, BLC, extended sensitivity, support on screen display etc.
b. 1/3" Image format varifocal lens ( 4 to 8 mm)
SITC of Advanced dynamic 4 channel digital event recording system with Digital multiplexer, DVR, Video
Motion Detection & Video management System features suitable for CCTV cameras and as specified in the
13.2 No. 1
technical specifications inclusive of the rack cost and inclusive of 1.5 TB storage Memory for 12.5 frames
second at 4CIF (704 X 576) resolution. TCP/IP connectivity, dual streaming and H.264 compression.
13.3 SITC of coaxial FRLS RG 6 cable for CCTV system. Metres 350
13.4 SITC of 2C x 1.5 sq mm FRLS cable . Metres 350
13.5 SITC of cam power supply Nos. 6
13.6 Supply & Installation of suitable stand for monitor of CCTV Nos. 1
14 P.A. SYSTEM
14.1 Supply, installation, testing and commissioning of public address/ music system comprising of the following:
SITC of solid state Amplifier of 240 W, RMS output including necessary control wires, jacks etc. any other
14.2 No. 1
accessories as required in complete.
14.3 SITC of DVD player with USB support No. 1
SITC of 6-9 W ceiling mounted speakers with line matching transformers with decorative grills, mounting
14.4 Nos. 12
bracket etc. other accessories as required in complete.
SITC of twin twisted 24/0.2 SWG flexible tinned copper PVC insulated and screened Copper cables for speakers
14.5 Metres 180
connections, volume control etc. through PVC conduits.
14.6 SITC of 2 zone call station No. 1
14.7 SITC of lapel microphone No. 2
14.8 SITC of Bosch make MW1‑LTX‑Fx Wireless Belt-pack Transmitter No. 1
14.9 Cordless Microphone Nos 2
14.1 SITC of Bosch make MW1‑LTX‑Fx Wireless Belt-pack Compatible Reciever No. 1
15 Wiring for T.V at Video Conference and Conference Room
15.1 Supply and laying of co-axial RG 6 cable for TV terminals Meters 180
15.2 Supplying and fixing of T.V Outlet in Modular Sheet /G.I Box etc as required Nos. 5
15.3 Supplying and fixing of HDMI PORT as required Nos. 5
15.4 Supplying and fixing of HDMI Cable with inbuilt port as required Meters 80
16 FIRE ALARM SYSTEM
Supply, installation, testing and commissioning of Single Loop Intelligent, Addressable Main Fire Alarm Control
panel suitable for operation on 230 V, 1 Ph, 50 Hz, AC supply with sufficient number control relay modules,
Data entry, necessary programming and comprising following as per specifications complete as required:- a)
Intelligent Detection Panel:- i) Microprocessor based central processing unit of at least 16 bit device, EPROM,
16.1 No. 1
non volatile memory with real time clock for communication and controlling the Intelligent / Addressable
devices and history buffer of 3000 events with time and date stamp. ii) Capable of integrating 125 Detectors
and 125 Modules. iii) operator interface, control and annunciation panel with back-lit alphanumeric liquid
crystal display, system status LED, two level password access and with alphanumeric keypad. iv) One no.
v) Suitable capacity maintenance free battery with 24 hours backup in normal conditions and 30 minutes in
alarm condition alongwith battery charger. vi) The housing cabinet shall be corrosion proof, with manufacture
standard finish, attack rated door, door lock and transparent viewing on front panel alongwith painting with
rust-resistant prime coat complete as required vii) shall be EN/UL/FM/VDS listed.

ARCHIVENTIONS- Architects Engineers, R.G.Baruah Road, Guwahati, Assam

 Supply, installation, testing and commissioning of intelligent addressable Smoke and Heat Detector
(Multisensor - 3D) with Standard base, Junction box,connector for loop in and loop out, insect resistant
16.2 Nos. 78
screen, built-in tamper resistant features including connection etc. with inbuilt isolator modules and other
accessories as required Detectors shall be EN/UL/FM/VDS listed.
16.3 Supply, installation, testing and commissioning of intelligent addressable reponse indicators Nos. 40
16.4 Supply, installation, testing and commissioning of intelligent addressable manual call point Nos. 4
16.5 Supply, installation, testing & commissioning of Addressable Hooter / SOUNDER complete with control Nos. 4
module.EN/UL / LPCB approved, make - HONEYWELL, MORLEY IAS, or equivalent as approved by the Deptt.)
Supply, installation, testing & commissioning of Intelligent Addressable monitor modules with standard base,
16.6 junction box, connector for loop in and loop out, built in tamper resistant features etc for integrating third No. 1
party inputs, shall be EN/UL/FM/VDS listed
Supply and laying 2 x 1.5 sq mm (14 SWG), 1.1 KV grade flame retardant copper conductor PVC cable with
16.7 Metres 680
steel braiding and overall shielded with aluminium mylar tape including connection etc. as required.
X FIRE EXTINGUISHERS
Supply installation testing & commissioning of ISI marked FIRE EXTINGUISHERS
1 ABC type - 2Kg No 8
2 ABC type - 5Kg No 4
TOTAL OF ELECTRICAL & OTHER RELATED WORKS

ARCHIVENTIONS- Architects Engineers, R.G.Baruah Road, Guwahati, Assam

 ESTIMATED BOQ FOR MODULAR FURNITURE WORKS OF CIRCLE OFFICE AT SIX MILE, GUWAHATI, ASSAM
SR.N DESCRIPTION QTY. UNIT RATE AMOUNT
O
1 For Workstation Area
i Linea Pentagonal Module (1500mmW1 x 1500mmW2 x 600mmD x 750mmH) mm 41 Nos
Providing and fixing Desking based Modular work stations , Linea Pentagonal
Module (1500mmW1 x 1500mmW2 x 600mmD x 750mmH) mm as per the Layout
Plan and detailed drawing with Mobile Pedestal (497mmH x 390mmW x 585mmD)
and without screen, as per details given below:
Each Modular Desk Linea Pentagonal Module should be provided with the following;
a) 25 mm thick pre laminated post formed table top.
b) Pedestal unit
c) Metal Key board Tray Ebco Make, with Mouse Pad
d) C.P.U trolley in metal
e) Frame works and legs for the table f)Wire Management
Desk based system with understructure comprising of leg assemblies and cross
connectors. Over the matrix of legs and cross connectors, the worksurfaces and wire
carriers are to be fixed. The legs used in the entire system are fabricated by CO2
welded MS tube of section 50.8mm x 50.8mm x 1.2mm thick (as per IS:7138 ERW).
Cross connectors are to be provided as supporting members which should span
across the leg assemblies and form the understructure of the workstation. The cross
connectors to be fabricated by CO2 welded MS tube of section 50.8mm x 50.8mm x
1.2mm thick (as per IS:7138 ERW) with 2 100mm x 55mm x 5mm L-shaped
connector brackets (IS: 2062 5mm HR) on either ends which have counter-sunk
holes and oblong slots (2 nos. each). Worksurface shall be made of 25mm thick pre-
laminated board conforming to IS: 12823. The top shall be laminated with 0.8 mm
thick laminate conforming to IS: 2046 and glue of PVAC. Bottom should have
backing laminate of 0.8mm thickness.
All the edges of the work surface shall be provided with machine pressed 2 mm
thick PVC liping glued with hot melt EVA glue. The undersurface of the worksurfaces
should be screwed to cross connectors and leg assembly. Spacers which are plastic
moulded with Nylon-6 are used to give the floating effect of worktop maintaining a
gap of 20mm between the understructure and the worktop. Access flap made of
Aluminium extrusion and ABS moulded ends are capped to both ends of extrusion.
The dimension should be 370mmL x 134mmW x 31mmH. Wire carrier is to be made
with a combination of Dia 3 mm and Dia 5mm MS Rod along with 5 mm thick MS
plates. All metallic parts should be of make Tata Steel/ JSW, Particle board and
lipping of make Merino, fittings of Ebco/ Hettich and powder coating of Nerolac
make powder.
B - PEDESTAL:
Free Standing Pedestals with castors: Dimensions : 646mmH X 497mmD X
390mmW: Construction and materials: Welded Assembled. 0.8mm thick CRCA for
Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom.
1.2 thick CRCA Top Stiffener & Bottom stiffener.
Drawer Fronts: Metal Front Straight Edge. Drawer Specifications: All Drawers with
Double extension precision ball slide. 390mm wide Pedestals File drawer - suitable
for storing Full-scape files in Depth wise manner. A4 files in width wise manner. For
Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts.
Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel
mechanism. Top Panel: 8mm thick Metal Straight Edge Top.
Castors: Swivelling non-lockable Castors mounted below the body shell. Anti-
tipping: Fifth roller arrangement mounted below File drawer to avoid toppling of
unit when file drawer is pulled out.
Partition in Drawer: 1 no. Partition in Box Drawers with lock mounted. Application /
Mounting Environment: Suitable for pushing below Grid work surface which has got
a clear height of 725 mm from below. Finish: Epoxy Polyester Powder coated to the
thickness of 50 microns (+/-10). All metallic parts should be of make Tata Steel/ JSW,
fittings of Ebco/ Hettich and powder coating of Nerolac make powder.

C – METAL KEYBOARD TRAY :

Each workstation should provided with powder coated finish Metal Keyboard Tray
of EBCO or equivalent make.
D - CPU TROLLEY :
Each workstation should be provided with M.S. powder coated finish adjustable
type CPU Trolley with 4 nos of casters, of EBCO or equivalent make
ii LINEAR Linea Recta Module WORKSTATION - 1500mmW x 600mmD x 750mmH 1 Nos
 Providing and fixing Desking based Modular work stations , Linea Module
(1200mmW x 600mmD x 750mmH) mm as per the Layout Plan and detailed drawing
with Mobile Pedestal (497mmH x 390mmW x 585mmD) and without screen, as per
details given below:
Each Modular Desk Linea Pentagonal Module should be provided with the following;
a) 25 mm thick pre laminated post formed table top.
b) Pedestal unit
c) Metal Key board Tray Ebco Make, with Mouse Pad
d) C.P.U trolley in metal
e) Frame works and legs for the table
f)Wire Management
Desk based system with understructure comprising of leg assemblies and cross
connectors. Over the matrix of legs and cross connectors, the worksurfaces and wire
carriers are to be fixed. The legs used in the entire system are fabricated by CO2
welded MS tube of section 50.8mm x 50.8mm x 1.2mm thick (as per IS:7138 ERW).
Cross connectors are to be provided as supporting members which should span
across the leg assemblies and form the understructure of the workstation. The cross
connectors to be fabricated by CO2 welded MS tube of section 50.8mm x 50.8mm x
1.2mm thick (as per IS:7138 ERW) with 2 100mm x 55mm x 5mm L-shaped
connector brackets (IS: 2062 5mm HR) on either ends which have counter-sunk
holes and oblong slots (2 nos. each). Worksurface shall be made of 25mm thick pre-
laminated board conforming to IS: 12823. The top shall be laminated with 0.8 mm
thick laminate conforming to IS: 2046 and glue of PVAC. Bottom should have
backing laminate of 0.8mm thickness.
All the edges of the work surface shall be provided with machine pressed 2 mm
thick PVC liping glued with hot melt EVA glue. The undersurface of the worksurfaces
should be screwed to cross connectors and leg assembly. Spacers which are plastic
moulded with Nylon-6 are used to give the floating effect of worktop maintaining a
gap of 20mm between the understructure and the worktop. Access flap made of
Aluminium extrusion and ABS moulded ends are capped to both ends of extrusion.
The dimension should be 370mmL x 134mmW x 31mmH. Wire carrier is to be made
with a combination of Dia 3 mm and Dia 5mm MS Rod along with 5 mm thick MS
plates. All metallic parts should be of make Tata Steel/ JSW, Particle board and
lipping of make Merino, fittings of Ebco/ Hettich and powder coating of Nerolac
make powder.
B - PEDESTAL:
Free Standing Pedestals with castors: Dimensions : 646mmH X 497mmD X
390mmW: Construction and materials: Welded Assembled. 0.8mm thick CRCA for
Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom.
1.2 thick CRCA Top Stiffener & Bottom stiffener.
Drawer Fronts: Metal Front Straight Edge. Drawer Specifications: All Drawers with
Double extension precision ball slide. 390mm wide Pedestals File drawer - suitable
for storing Full-scape files in Depth wise manner. A4 files in width wise manner. For
Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts.
Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel
mechanism. Top Panel: 8mm thick Metal Straight Edge Top.
Castors: Swivelling non-lockable Castors mounted below the body shell. Anti-
tipping: Fifth roller arrangement mounted below File drawer to avoid toppling of
unit when file drawer is pulled out.
Partition in Drawer: 1 no. Partition in Box Drawers with lock mounted. Application /
Mounting Environment: Suitable for pushing below Grid work surface which has got
a clear height of 725 mm from below. Finish: Epoxy Polyester Powder coated to the
thickness of 50 microns (+/-10). All metallic parts should be of make Tata Steel/ JSW,
fittings of Ebco/ Hettich and powder coating of Nerolac make powder.

C – METAL KEYBOARD TRAY :

Each workstation should provided with powder coated finish Metal Keyboard Tray
of EBCO or equivalent make.

D - CPU TROLLEY :
Each workstation should be provided with M.S. powder coated finish adjustable
type CPU Trolley with 4 nos of casters, of EBCO or equivalent make

iii LINEAR Linea Recta Module WORKSTATION - (1200mmW x 600mmD x 750mmH 1 Nos
Providing and fixing Desking based Modular work stations , Linea Module
(1200mmW x 600mmD x 750mmH) mm as per the Layout Plan and detailed drawing
with Mobile Pedestal (497mmH x 390mmW x 585mmD) and without screen, as per
details given below:
 Each Modular Desk Linea Pentagonal Module should be provided with the following;
a) 25 mm thick pre laminated post formed table top.
b) Pedestal unit
c) Metal Key board Tray Ebco Make, with Mouse Pad
d) C.P.U trolley in metal
e) Frame works and legs for the table
f)Wire Management
Desk based system with understructure comprising of leg assemblies and cross
connectors. Over the matrix of legs and cross connectors, the worksurfaces and wire
carriers are to be fixed. The legs used in the entire system are fabricated by CO2
welded MS tube of section 50.8mm x 50.8mm x 1.2mm thick (as per IS:7138 ERW).
Cross connectors are to be provided as supporting members which should span
across the leg assemblies and form the understructure of the workstation. The cross
connectors to be fabricated by CO2 welded MS tube of section 50.8mm x 50.8mm x
1.2mm thick (as per IS:7138 ERW) with 2 100mm x 55mm x 5mm L-shaped
connector brackets (IS: 2062 5mm HR) on either ends which have counter-sunk
holes and oblong slots (2 nos. each). Worksurface shall be made of 25mm thick pre-
laminated board conforming to IS: 12823. The top shall be laminated with 0.8 mm
thick laminate conforming to IS: 2046 and glue of PVAC. Bottom should have
backing laminate of 0.8mm thickness.
All the edges of the work surface shall be provided with machine pressed 2 mm
thick PVC liping glued with hot melt EVA glue. The undersurface of the worksurfaces
should be screwed to cross connectors and leg assembly. Spacers which are plastic
moulded with Nylon-6 are used to give the floating effect of worktop maintaining a
gap of 20mm between the understructure and the worktop. Access flap made of
Aluminium extrusion and ABS moulded ends are capped to both ends of extrusion.
The dimension should be 370mmL x 134mmW x 31mmH. Wire carrier is to be made
with a combination of Dia 3 mm and Dia 5mm MS Rod along with 5 mm thick MS
plates. All metallic parts should be of make Tata Steel/ JSW, Particle board and
lipping of make Merino, fittings of Ebco/ Hettich and powder coating of Nerolac
make powder.
B - PEDESTAL:
Free Standing Pedestals with castors: Dimensions : 646mmH X 497mmD X
390mmW: Construction and materials: Welded Assembled. 0.8mm thick CRCA for
Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom.
1.2 thick CRCA Top Stiffener & Bottom stiffener.
Drawer Fronts: Metal Front Straight Edge. Drawer Specifications: All Drawers with
Double extension precision ball slide. 390mm wide Pedestals File drawer - suitable
for storing Full-scape files in Depth wise manner. A4 files in width wise manner. For
Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts.
Locking: 10 lever Cam Lock & Central RH locking with actuator & lock channel
mechanism. Top Panel: 8mm thick Metal Straight Edge Top.
Castors: Swivelling non-lockable Castors mounted below the body shell. Anti-
tipping: Fifth roller arrangement mounted below File drawer to avoid toppling of
unit when file drawer is pulled out.
Partition in Drawer: 1 no. Partition in Box Drawers with lock mounted. Application /
Mounting Environment: Suitable for pushing below Grid work surface which has got
a clear height of 725 mm from below. Finish: Epoxy Polyester Powder coated to the
thickness of 50 microns (+/-10). All metallic parts should be of make Tata Steel/ JSW,
fittings of Ebco/ Hettich and powder coating of Nerolac make powder.

C – METAL KEYBOARD TRAY :

Each workstation should provided with powder coated finish Metal Keyboard Tray
of EBCO or equivalent make.

D - CPU TROLLEY :
Each workstation should be provided with M.S. powder coated finish adjustable
type CPU Trolley with 4 nos of casters, of EBCO or equivalent make
iv LINEAR Linea Recta Module WORKSTATION - 900mmW x 600mmD x 750mmH 1 Nos
Providing and fixing Desking based Modular work stations , Linea Module
(900mmW x 600mmD x 750mmH) mm as per the Layout Plan and detailed drawing
with Mobile Pedestal (497mmH x 390mmW x 585mmD) and without screen, as per
details given below:
Each Modular Desk Linea Pentagonal Module should be provided with the following;
a) 25 mm thick pre laminated post formed table top.
e) Frame works and legs for the table
 Desk based system with understructure comprising of leg assemblies and cross
connectors. Over the matrix of legs and cross connectors, the worksurfaces and wire
carriers are to be fixed. The legs used in the entire system are fabricated by CO2
welded MS tube of section 50.8mm x 50.8mm x 1.2mm thick (as per IS:7138 ERW).
Cross connectors are to be provided as supporting members which should span
across the leg assemblies and form the understructure of the workstation. The cross
connectors to be fabricated by CO2 welded MS tube of section 50.8mm x 50.8mm x
1.2mm thick (as per IS:7138 ERW) with 2 100mm x 55mm x 5mm L-shaped
connector brackets (IS: 2062 5mm HR) on either ends which have counter-sunk
holes and oblong slots (2 nos. each). Worksurface shall be made of 25mm thick pre-
laminated board conforming to IS: 12823. The top shall be laminated with 0.8 mm
thick laminate conforming to IS: 2046 and glue of PVAC. Bottom should have
backing laminate of 0.8mm thickness.
All the edges of the work surface shall be provided with machine pressed 2 mm
thick PVC liping glued with hot melt EVA glue. The undersurface of the worksurfaces
should be screwed to cross connectors and leg assembly. Spacers which are plastic
moulded with Nylon-6 are used to give the floating effect of worktop maintaining a
gap of 20mm between the understructure and the worktop. Access flap made of
Aluminium extrusion and ABS moulded ends are capped to both ends of extrusion.
The dimension should be 370mmL x 134mmW x 31mmH. Wire carrier is to be made
with a combination of Dia 3 mm and Dia 5mm MS Rod along with 5 mm thick MS
plates. All metallic parts should be of make Tata Steel/ JSW, Particle board and
lipping of make Merino, fittings of Ebco/ Hettich and powder coating of Nerolac
make powder.
2 LOOSE TABLE
A A. EXECUTIVE TABLE
The Table set should have Main Table + Side Table + Mobile Pedestal Unit. The ERU
and pedestal unit should be indepedently placed as per user preference.

Main Table: Main table top size should be 2400mmW x 900mmD. Should be made
of 68mm+/-1 mm thick combination of MDF, particle board and solid wood (batton
construction) with top veneer face coated with clear lacquer. Side panel (683mm x
600mm) should be made of 60mm +/-1 thick combination of MDF, particle board
and solid wood (batton construction) with top veneer face coated with clear
lacquer. Modesty panel (2240mm x 600mm) should be made of 17mm +/-1 thick
combination of MDF, particle board and solid wood (batton construction) with top
veneer face coated with clear lacquer.
ERU: Size: 1200mW x 440mmD x 650mmH. Top panel should be (1200mm x 440mm)
made of 22mm+/-1mm thick particle board. Side panel should(440mm x 546mm)
made of 17mm+/-1 mm thick particle board. Back panel should be (1164mm x
546mm) made of 17mm+/-1 mm thick particle board. Bottom panel should be
(1200mm x 440mm) made of 17mm+/-1 mm thick particle board. Hinged door panel
should be (340mm x 546mm) made of 17mm+/-1 mm thick particle board. Shelf
panels should be (546mm x 404mm) and (344mm x 404mm) made of 16mm +/-
1mm thick particle board. Surface finish should be Veneer face/ coated with clear
lacquer. All thickness edges are edge banded with matching lipping.
Pedestal: Size 443mmW x 510mmD x 635mmH. Top panel should be( 443mm x
510mm) made of 22mm+/-1 mm thick particle board. Side panel should be (490mm
x 549mm) made of 17mm+/-1 mm thick particle board. Back panel should be
(408mm x 548mm) made of 16mm +/-1mm thick particle board. Bottom panel
should be (408mm x 473mm) made of 16mm +/-1mm thick particle board. Drawer
fronts (440mm x 158mm) top drawer (440mm x 190mm) for middle and bottom
drawers should be made of 17mm+/-1 mm thick particle board. Surface finish
should be Veneer face/ coated with clear lacquer. All thickness edges are edge
banded with matching
Back Storage lipping.
: (2111mmW x 410mmD x 2000mmH).Top panel should be( 2211mm x
410mm) made of 22mm+/-1 mm thick particle board. Side panel should be
(1978mm x 390mm) made of 17mm+/-1 mm thick particle board. Back panel should
be 3 numbers made of 4mm +/-1mm thick pre-laminated MDF. Bottom panel
should be 3 numbers made of 16mm +/-1mm thick particle board. Top hinged door
panels should be 2 numbers made of (440mm x 1150mm)made of 17mm+/-1 mm
thick particle board. Top glass door panel should be 3 numbers made of (440mm x
1150mm) made of 17mm+/-1 mm thick particle board frame with tempered glass of
5mm thickness. bottom hinged door panels should be 5 numbers (440mm x
766mm) made of 17mm+/-1 mm thick particle board. Surface finish should be
Veneer face/ coated with clear lacquer. All thickness edges are edge banded with
matching lipping.
CPU Trolley should be made up of M.S. Sheet with powder coated finish and the
bottom should have 4 nos. of best quality
i Dy. General Manager's Table- 2400mm x 1000mm x 750 mm, COMPRISING OF - 1 Nos
A) Main Table
B) Side Unit
C) Back Storage
D) Pedestal
E) CPU Trolley

B EXECUTIVE TABLES
The table should be of overall dimension (2100mmW x 2250mmD x 750mmH).

Primary work-surface: The primary work-surface (2100mmW x 1050mmD) should be

made of 25mm thick pre-laminated twin board of E1-P2 grade and approved shade
confirming to IS-12823:1990, edge-banded with matching 2mm thick PVC lipping.

Secondary work-surface: The secondary work-surface (1200mmW x 500mmD)

should be made of 25 mm thick one side pre-laminated board conforming to IS-
14587:1998 with 0.4 mm PVC membrane pressed on to the top. Soft-closing access
flap with in-build power box should be provided on work-surface for wire-
management.
Modesty panel: The modesty panel should be made of 25 mm thick one side pre-
laminated board conforming to IS-14587:1998 with 0.4 mm PVC membrane pressed
on to the top.
Under-structure: The under-structure should be made of 25mm thick pre-laminated
twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge-
banded with matching 2mm thick PVC lipping.
Integrated Pedestal: Integrated pedestal should be fixed below both primary and
secondary work-surface and should be made of 25mm Thick Pre-laminated twin
board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge
banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick
MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC
membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses
powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325
MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for
ease of opening. Pedestal is provided with lock for security.
Back Unit: The over-all dimension should be (1800mmW x 500mmD x 750mmH).
The top panel should be Made of 25mm thick MDF one side pre-laminate board
confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Sliding
door unit: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and
approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm
thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are
made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998
with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti
slam mechanism.
Handles are provided for ease of opening. Storage is provided with lock for security.

i Asst. General Manager's Table - 2100mmW x 2250mmD x 750mmH, comprising of - 3 Nos

A) Main Table
B) Side Unit
C) Back Storage
D) Pedestal
E) CPU Trolley

c OFFICERS TABLE
The Table set should have Main Table + Side Table + Mobile Pedestal Unit. Main
table: should be made of 25 MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH
0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING
LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK
PVC BEADING. MODESTY: 18MM THICK PLAIN PARTICLE BOARD (PPB)
CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH
SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING.
ERU: 25 MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 0.6MM THICK POST
FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY
SEALED WITH 2MM THICK PVC BEADING. MODESTY: 18MM THICK PLAIN PARTICLE
BOARD (PPB) CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH
SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING.

i Divisional Manager's Table- 1650mm x 750mm x 750mm, comprising of - 5 Nos

A) Main Table
B) Side Unit
C) Pedestal
D) Metal Key Board Tray with Mouse pad
 E) CPU Trolley

ii Office/ Asst Manage/ Manager's Table- 1500mm x 750mm x 750mm, comprising 16 Nos
of -Main Table
A)
B) Side Unit
C) Pedestal
D) Metal Key Board Tray with Mouse pad
E) CPU Trolley

3 Modular Low Height Storages

Supplying and fixing in positions, Modular Lockable Low Height storage units.
Construction should be knockdown construction of 25mm thick and 18mm thk pre
laminated boards with metal cladding of 0.8mm thick CRCA from outside. Side
metal cladding should be Epoxy polyester powder coated with 50+/- 10 microns.
Top should be 11mm thick bent metal tops made of 0.8mm thick CRCA (as per IS:
513) and coated with Epoxy polyester powder of 50+/- microns.Two door opening
for doors should be provided and made of 18mm thk pre laminated boards with
decorative laminate on one side and backing laminate on the other side. Shelving
should be 1 number adjustable shelf and 1 number fixed shelf without vertical
partition for 900mmW unit and 2 nos. adjustable shelves and 2 nos. fixed shelves
with vertical partition in between for 1050mm width unit. UDL for each shelf should
be 40 kg. Skirtings of 150mm height should be provided. Skirting should be made of
0.8mm thick CRCA and powder coated to a thickness of 50+/-10 microns. Screw type
adjustable leveler with plastic base should be provided for vertical adjustment for
uneven floors and leveling of units. Back panels should be made of 18 mm thick PLB
and have splits back top paneland split back bottom panel separated by aluminium
extrusion.3 way nickel plated wooden furniture lock should be provided for
effective and positive locking of doors. Recessed Handles should be made of
aluminium extrusion for easy opening and closing. All metallic parts should be of
make Tata Steel/ JSW, Particle board and lipping of make Woodhouse, fittings of
Ebco/ Hettich and powder coating of Nerolac make powder.
i 1000mmW x 750mmH x 460mmD 3 Nos
ii 1050mmW x 750mmH x 460mmD 1 Nos
iii 1300mmW x 750mmH x 460mmD 6 Nos
iv 1500mmW x 750mmH x 460mmD 11 Nos
v 1600mmW x 750mmH x 460mmD 1 Nos
vi 1800mmW x 750mmH x460mmD 2 Nos
vii 1900mmW x 750mmH x 460mmD 2 Nos
viii 2000mmW x 750mmH x 460mmD 1 Nos
ix 2100mmW x 750mmH x 460mmD 4 Nos
x 2250mmW x 750mmH x 460mmD 2 Nos
xi 2400mmW x 750mmH x 460mmD 2 Nos
xii 2850mmW x 750mmH x 460mmD 2 Nos
xiii 3000mmW x 750mmH x 460mmD 5 Nos
xiv 3450mmW x 750mmH x 460mmD 1 Nos
xv 6750mmW x 750mmH x 460mmD 1 Nos

4 Discussion tables 1 Nos

Providing and placing 600 mm dia , 2-Seater free standing round tables as per the
following details
Table top
Table top to be 12 mm Toughned glass with bevelled edges, machine polished as
per the drawing and as directed by the Architect/ Engineer-in-charge

Table tops shall be single piece and shall be cut as per profile shown in the drawings.

Framework
Table support framework to be powder coated M.S framework as per propreitory
design.
5 BOOK SELVES
4 Door book case of size: 1742mm H x 914mm W x 320mm D, made of made of 6 Nos
0.7mm thick CRCA MS epoxy powder coated with knock down construction. Each
door should have 6 leaver cam lock with common key. Each door should have 3mm
thick glass for clear inside vission secure in metal frame through rubber gasket.

GRAND TOTAL
xii 2850mmW x 750mmH x 460mmD 2 Nos
xiii 3000mmW x 750mmH x 460mmD 5 Nos
xiv 3450mmW x 750mmH x 460mmD 1 Nos
xv 6750mmW x 750mmH x 460mmD 1 Nos
4 Discussion tables 1 Nos
Providing and placing 600 mm dia , 2-Seater free standing round tables as per the
following details
Table top
Table top to be 12 mm Toughned glass with bevelled edges, machine polished as
per the drawing and as directed by the Architect/ Engineer-in-charge

Table tops shall be single piece and shall be cut as per profile shown in the drawings.

Framework
Table support framework to be powder coated M.S framework as per propreitory
design.
5 BOOK SELVES
4 Door book case of size: 1742mm H x 914mm W x 320mm D, made of made of 6 Nos
0.7mm thick CRCA MS epoxy powder coated with knock down construction. Each
door should have 6 leaver cam lock with common key. Each door should have 3mm
thick glass for clear inside vission secure in metal frame through rubber gasket.

GRAND TOTAL
 ESTIMATED BOQ FOR BROUGHT OUT FURNITURE FOR FURNISHING WORKS OF CIRCLE OFFICE AT SIX MILE, GUWAHATI, ASSAM

SL NO: DESCRIPTION QTY UNIT RATE AMOUNT IMAGE

G BOUGHT OUT FURNITURE
1 SOFAS
1 Providing and supplying Sofas of approved make and colour. Sofas shall have mild
steel chrome plated legs finished with leatherite. i) Seat foam : The seat is made of PU
foam with density 32+/-2 kg/cu.mtr. having an additional top layer f PU foam with
density 28+/-2 Kg/cu.cm. Seat is upholstered with leatherette.
ii) Back foam : The back foam in made of PU with density 28+/-2 kg/cu.mtr. with two
additional top layer of supersoft foam of density 23+/-2 kg/cu.mtr, upholstered with
leatherette.
iii) Understructure :Understructure is made up of 1.2+/-0.1 cm thick hot pressed plywood
measured as per QA method. Dia 4 mm zigzag spring assembly is mounted in
understructure for support and additional cushioning purpose.
iv) Leg Assembly : It is a welded assembly made in Stainless steel (Grade SS202) tube &
plate.
Colour of Fabric as per
Architect's Design
a Two seater Leatherette Sofa in black colour 9 NOS.
2 a) SIDE FRAME ASSEMBLY: The side frame assembly is fitted to the two ends of the
connecting beam assembly to form the leg-cum-armrest assembly. It is made of a MS.
E.R.W. tube dia. 3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated. The ends are
fitted with ABS moulded end caps.
b) TIE MEMBER: It is the connecting beam assy. which holds the two side frames to
each other. 2 nos. tie members are used to connect the side frames. The tie-member is
made of MS. E.R.W. tube dia.3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated.
The seat/back assemblies are mounted on one of the tie-member which has 5cm x
5.5cm long x 0.5cm. thk MS. Std. angles welded to mount the seat and back.
c) SEATREST ASSEMBLY: The seat rest assembly consists of a fabricated inner-frame
assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3.
The hardness of the P.U. foam = 23 - 27 Kgs. on Hampden m/c. for 25% compression of
the foam. The complete moulded seat rest assembly is covered with a replaceable
fabric upholstery cover.
SEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T)
d) BACKREST ASSEMBLY: The backrest assembly is flexing type and consists of a
fabricated inner-frame assembly insitu-moulded with Polyurethane foam having
density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden
m/c. for 25% compression of the foam. The complete moulded backrest assembly is
covered with a replaceable fabric upholstery cover.
BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T)
e) ADJ. GLIDES: The adj. glide is injection moulded in black Nylon & fitted to the front
end of side frame assembly along with ABS moulded adj. Glide base to take care or
unlevelled floor surface.

Colour of Fabric as per

Architect's Design
b Two seater Tadem Sofa with Cushioned seat and back in chrome finish 3 NOS.

2 CHAIRS
i a) Seat Assembly : The cushioned seat should be made up of moulded plastic outer &
inner. Plastic inner is upholstered with leatherette and moulded High Resilience (HR)
Polyurethane foam of density 45+/-2 Kg/m3 and hardness load 16+/- kgf as per IS:7888
for 25% compression.
Seat size : 47.0 cm(W) x 48.0 cm (D)
b) Back Assembly : The cushioned back is made of PU foam with insitu moulded MS
ERW round tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. It is upholstered with
leatherette.
High Back size : 47.7 cm (W) x 76.4 cm (D)

c) Armrests : The armrest top should be moulded from polyurethane (PU) and mounted
on to a drop lift adjustable type tubular armrest support made of dia 3.81+/-0.03 cm x
0.2 +/- 0.01 cm thick MS ERW tube having chrome plated finish. The armrest should be
height adjustable up to 6.5 +/- 0.5 cm in 5 steps.
d) Mechanism : It should have active bio synchro mechanism with adjustable tilting
designed with the following features:
360 degree revolving type. Front-pivot for tilt with feet resting on ground and
continuous lumbar support ensuring more comfort. Tilt tension adjustment should be
able to operate on seating position with 5 position tilt limiter. The mechanism housing
should be made up of HPDC Aluminium black powder coated.
e) Seat depth adjustment : The seat depth adjustment should be integrated in the seat
through a sliding mechanism. Seat depth adjustment range is of 6.0+/-0.5 cm.
 f) Adjustable Back support : Back frame should be connected to the Up/Dn
mechanism housed in plastic T spine. It should be adjusted in the range of 7.42+/-0.5
cm for the comfortable back support to suit individual need.

g) Pneumatic ht. adjustment : The pneumatic ht. adjustment should have an

adjustment stroke of 10.0+/-0.3 cm.
h) Pedestal Assembly : The pedestal should be of high pressure die cast polished
aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0+/-0.5
cm pitch centre dia (75.0 +/- 1.0 cm with castors).
i) Twin wheel Castors : 5 nos. twin wheel castors to be provided and are to be injection
moulded in plastic having 6.0 +/- 0.1 cm wheel diameter and assembled to pedestal.
j) Overall Size :
Width (W) : 76.1 cm
Depth (D) : 76.1 cm

(a) DGM's CHAIR

Revolving High Back chair with Leatherette upholstery, Active Bio-Synchro, Die cast 1 Nos
polished Aluminum Pedestal, Adj Arms, 5 Position Tilt Limiter, Back Ht Adj,Seat Slide
Mech as per detailed specification and model/shade approval of the consultant
ii i). Seat / Back Assembly : The seat is made up of 1.2+/-0.1cm thk. hot pressed plywood
measured as per QA method. The back is made up of injection moulded gall filled
nylon & upholstered using net fabric with high tenacity yarn.
-Seat Size (Larger Seat Depth) (PULSAL, PULSTL): 47.0 cm (W) x 51.5 cm (D)
-Seat Size (Standard Seat Depth) (PULSAX, PULSTX): 47.0 cm (W) x 49.5 cm (D)
- Back Size : 45.0 cm (W) x 65.3 cm (H)
ii) High resilience (HR) Polyurethane Foam : The HR polyurethane foam is moulded with
density = 55+/-2 kg/m3 and hardness 16+/-2 kgf as per IS:7888 for 25% compression.
iii) Armrests (Adjustable)(PULSAX, PULSAL): The armrests have an up-down adjustment of
8.5+/-0.5 cm which is provided in armrest structure. Armrest Top has an integrated layer
of Thermostatic Elastomer (TPE).

iv) Armrests )Fixed)(PULSTX, PULSTL): The armrests is made of plastic injection moulded
nylon with textured top.
v) Lumbar support assembly : The Lumbar support consists of polypropylene pad with
moulded polyurethane foam & covered with polyester fabric. The height of lumbar
pad can be adjusted through two projecting knobs provided on the rear of the pad.
Lumbar pad has an adjustment of 8.0 +/-0.5 cm in height.
vi) Front Pivot Synchro Mechanism : The adjustable tilting mechanism is designed with
the following features.
- 3600 revolving type.
- Single point control.
- Front-pivot for tilt with feet resting on ground ensuring more comfort.
- Tile tension adjustment.
- 4 position locking with anti-shock feature.
- Seat/back tilting ratio of 1:2.

vii) Neckrest (PULSNR): The Neckrest assembly consist of polypropylene pad with
moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to Back
Assembly through Neckrest connector. Neckrest assembly has height adjustment of
4.2+/-0.5 cm and rotation adjustment of overall 760+/-20. The complete neckrest
assembly is retro fot to the mail chair.
viii) Pneumatic Height Adjustment : The pneumatic height adjustment has an
adjustment stroke of 10.0+/-0.3 cm.
ix) Pedestal assembly : The pedestal is injection moulded in black 30% galss-filled Nylon
and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is dia66.1+/-0.5
cm. (76.1+/-1.0 cm with castors)
x) Twin Wheel Castors : The twin wheel castors are injection moulded in black Nylon.
Colour of Fabric as per
Architect's Design
(a) AGM's CHAIR
High back with headrest Mesh Back, Knee tilt mechanism Mechanism, Adjustable Arms 3 Nos

iii Chair should have pneumatic seat height adjustment facility. Height of the chair
should be atleast 110cm. Depth and width of the chair should be at least 76cm. Seat
height should be at least 54cm.Back size-47.5cmWx69.5cmH. The seat and back
should be made up of 1.2±0.1 cm thick hot pressed plywood upholstered with fabric
upholstery cover and moulded polyurethane foam .The back Foam should be
designed with countered lumbar support for extra comfort. The High resilience
polyurethane Foam should be moulded with density=45±2kg/m3 and hardness load
16±2 kgf. The armrest should be injection moulded from black Co polymer polprylene.
It should have centre tilt mechanism with tilt tension adjustment, upright position
locking, 360 degree revolving and seat back tilting ratio should be 1:3.The pedestal
should be injection moulded in black 33% glass filled Nylon-66. The pedestal should
also have 5 nos twin wheel castor.
Colour of Fabric as per
Architect's Design
(a) DM's/ Section Incharge"s/ Doctor's CHAIR
 Green-guard certified High back Revolving chair with Centre tilt synchro, Nylon 21 Nos
Pedestal, PP Fixed Arms, Nylon Pedestal
iv 1. SEAT/BACK ASSEMBLY : The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed
plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered
with synthetic leather over moulded High Resilience Polyurethane foam.
* MID BACK SIZE: 51.6 cm. (W) x 65.7 cm. (H)
* SEAT SIZE : 49.0 cm. (W) x 51.4 cm. (D)
2. HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR polyurethane foam is moulded
with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.
3. ARMRESTS : The adjustable armrest is designed with the following features :
• Up-Down adjustment– 8 steps (8.0±0.5cm range)
• Height adjustable armrest structure which is chrome plated & fitted with an armrest
top.
• Fixed Armrest Top is PU moulded over metal insert.

4. (A) FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is

designed with the following features.
• 360° revolving type.
• Single point control.
• Front-pivot for tilt with feet resting on ground ensuring more comfort.
• Tilt tension adjustment.
• 4-position locking with anti-shock feature.
• Seat/back tilting ratio of 1:2.
(B) BACK HEIGHT ADJUSTABILITY : Back can be adjusted in 5 positions by manually.
Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for
High back and Mid back chair.
5. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an
adjustment stroke of 10.0 ± 0.3 cm.

6. PEDESTAL ASSEMBLY WITH CASTORS : The pedestal is High Pressure Die cast polished
Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-
center dia.(75.0 ± 1.0cm. With castors.)
7. TWIN WHEEL CASTOR : The twin wheel castors are injection moulded in black PP.
8. TUBULAR VISITOR FRAME (Visitor Chair) : The tubular frame is powder coated ( DFT 40-
60 microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk.
M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the
frame assembly.
9. OPTION OF SLIDING SEAT MECHANISM : Seat can be slide horizontally as per user
convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal
type of chair. Colour of Fabric as per
Architect's Design
(b) DGM's Visitor's , Video Conference (General) & Conference (General) Chair
Medium back, leatherette chair with multiple recline lock and kneetilt mechan ism, 63 NOS
with chrome plated metal base & chrome plated fixed arms
iv 1. Seat/Back Assembly: The seat is made up of 1.2 cm. thick hot pressed plywood
upholstered with fabric and moulded Polyurethane Foam. The back is made up 1.2
cm. thick hot pressed plywood upholstered with replaceable fabric upholstery covers
and moulded polyurethane foam. The back ply and foam is designed with contoured
lumber support for comfortable seating posture. BACK SIZE: 41cm.(W) X 46.0cm.(H),
SEAT SIZE: 43.0cm.(W) X 41.0cm.(D)
2. Polyurethane Foam: The polyurethane foam for seat and back is moulded with
density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2.
3. Armrest : The armrest top is made of moulded polyurethane (P.U)
4. Permanent contact mechanism
• 360° revolving type.
• maximum 14 degree back tilt
5. Pneumatic Height Adjustment: The pneumatic height adjustment has an adjustment
of 9.0cm.
6. Pedestal Assembly: The pedestal is fabricated from steel,
7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon.

Colour of Fabric as per

Architect's Design
(a) Officer's/ Assistant's/ Discussion room's/ Reception's etc. CHAIR
Medium back revolving chair Perm Cont Mech Upright Position locking, designer 44 Nos
triangular fixed Arms, Powder coated Pedestal
v 1. SEAT/BACK ASSEMBLY: The seat is made up of 1.2 cm. thick hot pressed plywood
upholstered with fabric and moulded Polyurethane Foam. The back is made up 1.2
cm. thick hot pressed plywood upholstered with replaceable fabric upholstery covers
and moulded polyurethane foam. The back ply and foam is designed with contoured
lumber support for comfortable seating posture.
BACK SIZE: 39.0cm.(W) X 38.cm.(H), SEAT SIZE: 45.0cm.(W) X 42.0cm.(D)
2. POLYURETHANE FOAM: The polyurethane foam for seat and back is moulded with
density = 45±2 kg/m3 and Hardness = 20±2.
5. LEG FRAME ASSEMBLY: tubular frame made up of MS E.R.W. tube and balck powder
coated Colour of Fabric as per
Architect's Design
(a) General Visitor's Chair
Visitor chair with cushioned seat with tilting mechanism, fixed arms with MS base 51 Nos
vi The seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with
fabric or synthetic leather and moulded Polyurethane foam.the back is made up
1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic
leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is
designed with contoured lumber support for comfortable seating posture.Back
size:48cm(W) x 64.5 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience
polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness
load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded
polyurethane and mounted on to a drop lift height adjustable type M.S.

Tubular armrest support chrome plated.The armrest height is adjustable upto

6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The
mechanism is knee-tilt synchro mechanism with following features:360° revolving
type,single point control,front pivot for tilt with feet resting on ground ensuring more
comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back
tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6
positions.The backrest consists of a sliding up down mechanism,which can be adjusted
in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of
lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The
pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin
pass),chrome plated and assembled with injection moulded black polypropylene hub
cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch centerdia
(76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon.

Colour of Fabric as per

Architect's Design
(a) Conference & Video Conference Chair (Speakers)
Mid Back Revolving chair with KTS Mech 4 Position Locking, Soft touch PU Arms, 6 NOS
Chrome-Plated arms & Pedestal, Adj Backrest,

Colour of Fabric as per

Architect's Design
GRAND TOTAL
B TOTAL OF BROUGHT OUT ITEMS