PDS Series

UNIVERSAL SERVO DRIVE

INSTRUCTION MANUAL

version: 1.2
software rel. V9.44
 WARNING! !
Attention to these warning signs on the drive or in this instruction book, they indicate danger to human
body or damage to the drive.
Before installing and putting the drive into operation, please read the safety precautions and warnings
following this page.
Safety precautions & warnings
Read carefully all the safety precautions included in these operating instructions and all the warning signs attached to the
drive. Make sure that the warning signs are kept in a legible condition and replace missing or damaged signs.
Before starting, familiarize yourself with the operation of the drive. It may be too late if you start working with the drive
before read this instruction manual.
Never permit unqualified personnel to operate the drive.
! WARNING
This drive produces dangerous electrical voltages and controls rotating mechanical parts. Death, severe injury or substantial
damage to property can occur if the instructions in this operating manual are not completed with.
Only personnel with appropriate qualifications should work with this drive. These personnel must be familiar with all the
warning signs and precautions laid out in these operating instructions for the transport, installation and operation of this drive.
The successful and safe use of this drive depends on the correct installation, commissioning, operation and maintenance of
the drive.
This drive operates at high voltages.
l The DC-link capacitors remain charged to dangerous voltages even the power is removed. For this reason it is not
permissible to open the drive cover until five (5) minutes after the power has been turned off. When handling the open
drive it should be noted that live parts are exposed. Do not touch these live parts.
l The terminals R, S, T, U, V, W, P, N, B, PR, BR can carry dangerous voltages even if the motor is inoperative:
l Only qualified personnel may connect, start the system up and repair faults. These personnel must be thoroughly
acquainted with all the warnings and operating procedures contained with this manual.
l Certain parameter settings may cause the drive to start up automatically after power on or power recover.
DEFINITIONS
Qualified Person
For the purposes of this manual and product labels, a qualified person is one who is familiar with the installation, construction,
operation and maintenance of this drive and with hazards involved. In addition, the person must be:
l Trained and authorized to energize, de-energize, clear, ground and tag circuits and equipment in accordance with
established safety practices.
l Trained in the proper care and use of protective equipment in accordance with established safety practices.
l Trained in rendering first aid.
Danger
For the purposes of this manual and product labels, DANGER indicates that loss of life, severe personal injury or substantial
property damage WILL result if proper precautions are not taken.
Warning
For the purposes of this manual and product labels, WARNING indicates that loss of life, severe personal injury or substantial
property damage CAN result if proper precautions are not taken.
Caution
For the purpose of this manual and product labels, CAUTION indicates that minor personal injury or property damage CAN
result if proper precautions are not taken.
Note
For the purpose of this manual and product labels, NOTES merely call attention to information that is especially significant in
understanding and operating the drive.
! DANGER and WARNING
Make sure that the location selected for installation is safe, protected from moisture and splash and drip-proof!
Children and the general public must be prevented from accessing or approaching the equipment!
The equipment may only be used for the purpose specified by the manufacturer.
Unauthorized modifications and the use of spare parts and accessories that are not sold or recommended by the manufacturer
of the equipment can cause fires, electric shocks and injuries.
Keep these operating instructions within easy reach and give them to all users!
! WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.

1
CONTENTS
1. Description of PDS Servo Drive ..................................................................................................................................... 4
1.1 Brief Function Description.......................................................................................................................................... 4
1.2 Control input & output configuration........................................................................................................................... 4
1.2.1 A/B/C Input Interface of Motor Feedback Encoder................................................................................................ 6
1.2.2 XY Pulse Input Interface....................................................................................................................................... 6
1.2.3 Digital Input (DI0~DI14) ..................................................................................................................................... 7
1.2.4 Digital Output (DO0~DO6).................................................................................................................................. 7
1.2.5 Source/Sink Select ................................................................................................................................................ 8
1.2.6 Analog input AI1, AI2 & AI3 ................................................................................................................................ 8
1.2.7 Analog Output AO1, AO2 & AO3 ......................................................................................................................... 8
1.2.8 Hardware RESET (RST) ....................................................................................................................................... 9
1.2.9 RS485 Communication Interface .......................................................................................................................... 9
1.2.10 Standard Cables................................................................................................................................................. 9
1.2.11 Option Field Bus Interface.................................................................................................................................. 9
1.3 Electrical Rating Specifications................................................................................................................................... 9
2. Installation.................................................................................................................................................................... 10
2.1 Outline Dimensions .................................................................................................................................................. 10
2.2 Power Terminal ........................................................................................................................................................ 11
2.3 Connect Power Line Input to Driver.......................................................................................................................... 11
2.4 Connect Driver Output to Motor ............................................................................................................................... 11
2.5 Control Terminal Connection .................................................................................................................................... 11
2.6 DC BUS Terminal and Brake Terminal...................................................................................................................... 12
2.7 A.C.L. ...................................................................................................................................................................... 12
3. Control Panel................................................................................................................................................................ 13
3.1 CTL Mode................................................................................................................................................................ 13
3.2 MON mode .............................................................................................................................................................. 13
3.3 PAR mode ................................................................................................................................................................ 13
3.4 ALM mode............................................................................................................................................................... 13
4. Start-Up Examples ....................................................................................................................................................... 14
4.1 Basic Function Block................................................................................................................................................ 14
4.2 Setup Basic Motor Parameter .................................................................................................................................... 15
4.3 Default Setting of some simple Examples.................................................................................................................. 15
4.3.1 V/F Constant Mode for Induction Motor............................................................................................................. 15
4.3.2 Speed Mode for Induction Servo Motor............................................................................................................... 16
4.3.3 Tracking Mode (Pcmd) for Induction Servo Motor .............................................................................................. 16
4.3.4 Auto Point-to-Point control Mode for Induction Servo ........................................................................................ 17
4.3.5 Example for Brushless Servo Motor.................................................................................................................... 17
4.4 Auto Tuning for Servo Motors .................................................................................................................................. 18
4.4.1 Auto Tuning for Induction Servo Motor............................................................................................................... 18
4.4.2 Auto Tuning for Brushless Servo Motor .............................................................................................................. 18
4.4.3 Auto Tuning Resolver BL Servo Motor................................................................................................................ 18
5. Parameters.................................................................................................................................................................... 19
5.1 Parameter List .......................................................................................................................................................... 19
5.2 Parameter Description............................................................................................................................................... 23
5.2.1 Parameter Type.................................................................................................................................................. 23
5.2.2 Parameter Protection ......................................................................................................................................... 23
5.2.3 Parameter Initalization ...................................................................................................................................... 23
5.2.4 Speed & Acceleration/Deceleration Time............................................................................................................ 23
5.2.5 Control Function................................................................................................................................................ 24
5.2.6 Analog Input/Output Function............................................................................................................................ 26
5.2.7 Factory Adjustment Parameters.......................................................................................................................... 27
5.2.8 Monitor Function ............................................................................................................................................... 27
5.2.9 XY Pulse Command Input Parameters ................................................................................................................ 29
5.2.10 PID Function ................................................................................................................................................... 31
5.2.11 Motor Parameter Groups.................................................................................................................................. 33
5.2.12 Auto Point-to-Point Control.............................................................................................................................. 35

2
6. Selection of Speed Source ............................................................................................................................................. 37
6.1 Speed Source Selection Table.................................................................................................................................... 37
6.2 Description of Speed Source ..................................................................................................................................... 38
6.2.1 Speed Source from Memory & Panel................................................................................................................... 38
6.2.2 Speed Source from Analog Input ......................................................................................................................... 38
6.2.3 Speed Source from XY Pulse Input ...................................................................................................................... 40
6.2.4 Speed Source from Internal Up/Down Counter.................................................................................................... 41
6.2.5 Set Speed from Two Speed Sources Combination................................................................................................. 42
7. Selection of Digital Input Function .............................................................................................................................. 43
7.1 Digital Input Function Related Parameters................................................................................................................. 43
7.2 Selection Table of Digital Input Function .................................................................................................................. 43
7.3 Description of Digital Input function......................................................................................................................... 45
7.3.1 Control Function................................................................................................................................................ 45
7.3.2 Protection Function............................................................................................................................................ 46
7.3.3 Timer & Counter Function ................................................................................................................................. 46
7.3.4 Flip/Flop Function............................................................................................................................................. 48
8. Selection of Digital Output Function............................................................................................................................ 49
8.1 Digital Output Function Related Parameters.............................................................................................................. 49
8.2 Selection Table of Digital Output Function................................................................................................................ 49
8.3 Description of Digital Output Function...................................................................................................................... 50
8.3.1 Speed Monitor Function ..................................................................................................................................... 50
8.3.2 ON/OFF Control Function ................................................................................................................................. 51
8.3.3 Pulse Output Function........................................................................................................................................ 51
8.3.4 Running Status Monitor Function ....................................................................................................................... 51
9. RS485 Communication................................................................................................................................................. 53
9.1 RS485 Communication Port Related Parameters ....................................................................................................... 53
9.2 RS485 Port Configuration......................................................................................................................................... 53
9.3 JPS Protocol & Format ............................................................................................................................................. 54
9.3.1 Computer to Drive.............................................................................................................................................. 54
9.3.2 Drive to Computer.............................................................................................................................................. 55
9.4 HMI Protocol (Modbus(RTU)).................................................................................................................................. 56
9.4.1 Parameter Setting .............................................................................................................................................. 56
9.4.2 Definition of Modbus(RTU) and Drive................................................................................................................ 56
10. Block Diagram of PDS Drive...................................................................................................................................... 58

11. Special Function.......................................................................................................................................................... 59

11.1 MARK Function ..................................................................................................................................................... 59
11.1.1 Parameters Description.................................................................................................................................... 59
11.1.2 Running Status Monitor .................................................................................................................................... 60
11.1.3 S Ramp Curve................................................................................................................................................... 62

3
1. Description of PDS Servo Drive
1.1 Brief Function Description
Drives Different Motor types
l Brushless Servo Motor
l Induction Servo Motor
l Open Loop Induction Motor
l Memorize Four Motor Parameter Groups
Varity Control Modes in Single Drive
l Open Loop V/F or Sensorless Speed Mode
l Close Loop Speed Mode
l Torque Control Mode
l Pulse Command Tracking Mode
l Auto Positioning Mode
Enhanced Communication
l Standard RS485 Communication Port
Simple and direct protocol embedded for Computer/PLC control.
Baud Rate up to 4800, 9600, 19200, 38400
l Option Field Bus Module
Many commonly used Fieldbus option board can be selected, such as:
l Modbus(RTU)
l Profibus-DP
l InterBus
l DeviceNet
l ControlNet
l CANopen
* Other systems planned
Multi-Functioned I/O
l 11 Digital Inputs (Sink or Source selectable)
l 7 Digital Outputs (Sink or Source selectable)
l 3 Analog Inputs (±10V, +10V, +5V or 20mAselectable)
l 3 Analog Output (±10V)
l Encoder Clock Input
l Pulse Command Clock Input
l Encoder Clock Buffered Output

1.2 Control input & output configuration

Main CPU Board

I/O & Feedback Option

FieldBus Option
ABC out RS485

Encoder

XY input

AO2,3 DI7~10 & DO4~6

AO1 & AI1,2,3 DI1~6 & DO1,2 Ry1,2

4
The control terminals on the Main CPU board are separated into three groups.
Basic Analog I/O signals:

AO1 AI1 AI2 AI3 5V ACOM

Basic Digital I/O signals:

DI1 DI2 DI3 DI4 DI5 DI6 RST DO1 DO2 24V DCOM RY1 RY2
＊RY1, RY2 is normal open Relay output (equivalent to DO3)
Additional control terminals on Feedback I/O board:

AO2 AO3 ACOM DI7 DI8 DI9 DI10 DO4 DO5 DO6

Connectors on Feedback I/O Board

CON3: Encoder Feedback from Motor.

Equipped with accessory cable transforms into standard 15pin D-sub Male
connector. The pin definition of CON3 and 15 pin D-sub connector is:

CON3 15pin D-sub Male connector Definition Description

Pin1 Pin1 A l Pin1~Pin6 are used for both
Pin2 Pin2 /A induction and brushless motor.
Pin3 Pin3 B l Pin7~Pin12 used for brushless
Pin4 Pin4 /B motor only.
Pin5 Pin5 C l Encoder output should be Line
Pin6 Pin6 /C Drive type.
Pin7 Pin7 Uf l A, B are quadrature signals.
Pin8 Pin8 /Uf l Uf, Vf, Wf used for indicating the
Pin9 Pin9 Vf magnetic pole position of
Pin10 Pin10 /Vf brushless motor.
Pin11 Pin11 Wf
Pin12 Pin12 /Wf
Pin13 Pin13 +5V
Pin14 Pin14 0V
Pin15 Pin15 0V
Pin16 Case Shield

CON5: XY pulse command input port.

Equipped with accessory cable transforms into standard 9pin D-sub Female
connector. The pin definition of CON5 and D-sub connector is:

CON5 9pin D-sub Female connector Definition Description

Pin1 Pin1 X Refer to the following parameters:
Pin2 Pin2 /X Pr.130: XY Clock type select
Pin3 Pin3 Y Pr.131: XY Input pin status
Pin4 Pin4 /Y Pr.132: XY Direction change
Pin5 N.C. Pr.133~136: Multiply/Division rate
Pin6 N.C. Pr.137: XY counter value
Pin7 +5V Pr.138: XY Sampling Period
Pin5 Pin8 0V Pr.139: XY Rate
Pin7 Pin9 N.C.
Pin7 Case Shield

5
 CON4: Buffered A, B, C output port.

Equipped with accessory cable transforms into standard 9pin D-sub

Male connector. The pin definition of CON4 and D-sub connector is:

CON4 9pin D-sub Male connector Definition Description

Pin1 Pin1 Aout Buffered output of signal A
Pin2 Pin2 /Aout Buffered output of signal /A
Pin3 Pin3 Bout Buffered output of signal B
Pin4 Pin4 /Bout Buffered output of signal /B
Pin5 Pin5 Cout Buffered output of signal C
Pin6 Pin6 /Cout Buffered output of signal /C
Pin7 N.C. The above outputs are Line Driver
Pin7 Pin8 0V type
Pin9 N.C.
Pin8 Case Shield

1.2.1 A/B/C Input Interface of Motor Feedback Encoder

Vcc

220,1/4W
A+
A

A-

l The input hardware structure of signal B & C is same as signal A.

l The Encoder type muse be 5V Line Driver.

1.2.2 XY Pulse Input Interface

1.2.2.1 5V Line Drive Type
l The XY pulse input hardware structure is design as 5V Line Drive type input.
Vcc

220,1/4W
X+
X

X-

Note: The input hardware structure of signal Y is same as signal A

l Description of Line Drive input signal
5V
X+ 0V

5V
X- 0V

5V
X 0V

6
 1.2.2.2 +24V Open Collector Type
l If use 24V Open Collector type input signal, must add current limit resistor (2K,1W) as following.
Vcc

2K,1W 220,1/4W
+24V X+
X

X-

l Description of Open Collector signal

24V
X- 0V

5V
X 0V

1.2.3 Digital Input (DI0~DI14)

l DI1~DI10 are all identical Bi-directional digital inputs.
24V +24V DI1~DI6 located at Main CPU board, DI7~DI10 located at
Feedback I/O board.
Sink/Source jumper
l DI0 do not connect to the user control terminal, and only
DCOM +24V connected to DO0 internally, and can be controlled by
Pr.066 and Modbus communication.
l DI11~DI14 do not connect to the user control terminal,
To CPU and can only control by Modbus communication.
l +24V is common power supply for all DIx.
GND l DCOM is the command reference for these digital circuits.
l Each Digital Input can be configured individually by
DIx corresponding parameter Pr.140~Pr.154.
4.7k l User can select Sink (NPN) type or Source (PNP) type by
DCOM Common line of +24V jumper JP4.
Note: The minimum input signal width is 5ms.

1.2.4 Digital Output (DO0~DO6)

l DO1, DO2, DO4~DO6 are open collector output,
l RY1, RY2 is voltage isolated “1a” contact of Relay output, RY1/RY2 named DO3 also.
l DO1, DO2, RY1/RY2 located at Main CPU board.
l DO4~DO6 located at Feedback I/O board.
l DO0 do not connect to the user control terminal, and only internal connected with DI0.
l Each Digital output can be configured individually by corresponding parameter Pr.160~Pr.166.
l User can select Sink (NPN) type or Source (PNP) type by jumper JP5.
Note: RY1, RY2 should drive 24V relay only

7
 Open Collector output
5V
RY1

DO1,2 and RY2

Signal DO4,5,6
from CPU

Sink/Source Select jumper

1.2.5 Source/Sink Select

DI/DO select PNP or NPN type
l JP4 upper position select Source input
JP4 JP5 JP4 JP5 l JP5 upper position select Source output
l JP4 lower position select Sink input
l JP5 lower position select Sink output
or

NPN type DI/DO PNP type DI/DO

1.2.6 Analog input AI1, AI2 & AI3

AI, AI2 signal must input from control terminal input, can select ±10V, +10Vor +5V of input signal range by Jumper.

AI1 range select by JP1A & JP1B AI2 range select by JP2A & JP2B

or or or or

JP1A JP1B JP1A JP1B JP1A JP1B JP2A JP2B JP2A JP2B JP2A JP2B

±10V 0 ~ +5V 0 ~ +10V ±10V 0 ~ +5V 0 ~ +10V

AI3 signal may input from control terminal or by VR of control panel, can select +5Vor 20mA of input signal and input
from control terminal or panel by Jumper.
AI3 selection by JP3A & JP3B

JP3A determine the signal type JP3B determine the AI3 input source

+5V input from Terminal JP3B

Control by Panel VR
JP3A

or or

20mA input from Terminal JP3B

Control by Terminal
JP3A

1.2.7 Analog Output AO1, AO2 & AO3

AO1, Ao2 & AO3 are all identical analog outputs.
AO1 located at Main CPU board.
From CPU AO1,2,3 AO2, AO3 located at Feedback I/O board.
OPamp Each Analog Output can be configured individually by corresponding
±10V parameters. (Pr.210~213, 220~223, 230~233)

8
1.2.8 Hardware RESET (RST)
The hardware structure of RST terminal is similar to Digit Inputs description in Sec. 1.2.1.
Terminal RST is used for reset the servo drive. Under any circumstances, when RST terminal is activated, will force the
drive execute REST, as if Power on again.

1.2.9 RS485 Communication Interface

l To use JPS protocol embedded for computer/ PLC control.
l To use Modbus(RTU) communication option, let drive simulate as Modicon PLC and can direct connect with HMI.
The HMI can direct control and monitor the drive.

1.2.10 Standard Cables

The specification and application of standard cables describe as following:
Part No. Application Connector(1) Connector(2) Length(M)
CABLE_MEI Encoder Input D-sub 15Pin (Male) JS091-16F 0.5
CABLE_ABCKO A.B.C. Output D-sub 9Pin (Male) SC25-08HG 0.5
CABLE_XYCKI X.Y. Input D-sub 9Pin (Female) SC25-07HG 0.5
CABLE_HMIEV HMI D-sub 9Pin (Male) SC25-05HG 0.5
CABLE_RS485 RS485 SC25-05HG SC25-05HG 2
CABLE_EXT2D9 Extension D-sub 9Pin (Male) D-sub 9Pin (Female) 2
CABLE_EXT2D15 Extension D-sub 15Pin (Male) D-sub 15Pin (Female) 2

HMI、PLC、COMPUTER

RS422/485 CABLE_HMIEV
CABLE_RS485 For EasyView’s HMI,
must check pin definition for other HMI
Con1

XY Clock Input ABC Clock Input

PDS
CABLE_XYC Con5 Con4 CABLE_ABC

KI Con3 KO
Customer Prepare
CABLE_ME

Customer Prepare PG MOTOR

1.2.11 Option Field Bus Interface

Many commonly used Fieldbus option board can be selected for complete data exchange with PLC or PC, such as:
l Profibus-DP
l InterBus
l DeviceNet
l ControlNet
l CANopen
Consult to our R&D department if needed.

1.3 Electrical Rating Specifications

Model No. 2022 2037 2055 2075 2110 2150 2225
PDS- 4022 4037 4055 4075 4110 4150 4225 4300 4370 4450 4550 4750
HP 3 5 7.5 10 15 20 30 40 50 60 75 100
KW 2.2 3.7 5.5 7.5 11 15 22.5 30 37 45 55 75
KVA 4.0 6.5 9.5 13 19 25 34 46 57 73 84 106
Amp PDS-2xxx 11 17 24 33 46 61 90
(rms) PDS-4xxx 5.5 8.5 12 17 23 31 45 57 71 91 110 140

9
2. Installation
! WARNING
To guarantee the safe operation of the equipment it must be installed and commissioned properly by qualified
personnel in compliance with warnings laid down in these operating instructions.
Take particular note of the general and regional installation and safety regulations regarding work on high voltage
regulations, as well as the relevant regulations regarding the correct use of tools and personal protective gear.
l Make sure that the unobstructed clearance for each of the cooling inlets and outlets above and below the driver
is at least 100mm.
l Make sure that a space of 40mm is kept free at the sides of the driver to permit the cooling air to escape from the
side slits.
l Ensure that the temperature does not exceed the specified level when the driver is installed in cubicle.
l Avoid excessive vibration and shaking of the equipment.
l Do not be obstruct the cooling fan that installed on the drive, it is used to build proper airflow for heat sink
thermo dissipation. And do not touch the fan hole when it is running.
l Please consider the possible use of options, such as RFI suppression filters at the planning stage.
! WARNING
To prevent electrical shock, do not open cover for at least 5 minutes after removing AC power to allow capacitors to
discharge.

2.1 Outline Dimensions

unit: mm
157.6 10.0 Ø8.0 226 10.0
Ø5.5
193.6

206.0

400
420

170.0 152.2
PDS - 2022、2037、4022、4037
250 248
PDS-2110N, 2150N, 2225N, 4110N, 4150N, 4225N
(N) 313 234
Ø6.0 178 10.0 Ø13
286
300

300

729
691

192 190
PDS - 2055N、2075N、4055N、4075N 249
PDS - 4300

10
2.2 Power Terminal
The upper cover must be removed in order to connect the electrical leads.
Basically, the Power terminals are divided into three portions:
1. The Power line input, (R, S, T) receives power for the operation of the driver.
2. The Motor line output, (U, V, W) delivers Variable Frequency output to motor leads.
3. Brake resistor connect to B, P terminals
NOTE: Must connect Earth properly.
! WARNING: Never connect power line to U, V, W, P, N, B

2.3 Connect Power Line Input to Driver

! WARNING and CAUTION
l Between the power line and the driver, add NFB for system protection.
l There are static sensitive components inside the Printed Circuit Board. Avoid touching the boards or
components with your hands or metal objects.
l Only the terminal screws may be touched with the insulated screwdrivers when connecting the leads.
l Make sure to connect the power terminals tight and correctly.
l Make sure that the power source supplies the correct voltage and is designed for the necessary current.
l Make sure the motor is configured to match the input voltage.
l Protective EARTH terminal marked with must be connected properly.
l Take care that the appropriate circuit breakers with the specified current rating are connected between the
power supply and the driver.

2.4 Connect Driver Output to Motor

!WARNING
Do not insert contactors between driver output and motor.
For every model, "U, V, W " are the three phase output terminals, they should be connected to motor leads
directly.

2.5 Control Terminal Connection

! CAUTION
All the input/output control signal lines, or remote panel lines and communication lines must be laid separately
from the high current power/motor/brake lines. They must not be fed through the same cable
conduit/trucking.

11
2.6 DC BUS Terminal and Brake Terminal
! CAUTION
Some models with power terminal marked P and N, these models does not include Brake transistor inside the driver.
Customer may use extra Brake Transistor Module for discharge brake function.
For models that include braking transistor, the power terminal will mark P and B (PB or BR) User can connect
suitable resistor to the P & B (PR or BR) terminals directly.
Here is the recommended table for discharge resistors:
Model Resistance (Ohm) Rating (Watt)
2022 60 250
2037 40 300
2055 30 500
2075 20 600
2110 15 1000
2150 10 1500
4022 250 250
4037 150 300
4055 100 500
4075 75 750
4110 50 1000
4150 40 1500
Discharge duty 10 ％-

! Warning: Never connect resistor to P & N terminal

If the terminals are P & N, must add external braking unit.

2.7 A.C.L.
When power supply capacity is larger than 500KVA and /or using thyrister, phase advance capacitor etc. from same
power supply, must fitting A.C.L. at R.S.T. power input side to curb instantaneous current and to improve power ratio.
Here is the recommended table for A.C.L.
Voltage (V) Model Current (Arms) Induction value
PDS-2022 15 0.71mH
PDS-2037 20 0.53mH
PDS-2055 30 0.35mH
220 PDS-2075 40 0.26mH
PDS-2110 60 0.18mH
PDS-2150 80 0.13mH
PDS-2225 120 0.09mH
PDS-4022 7.5 3.6mH
PDS-4037 10 2.2mH
PDS-4055 15 1.42mH
PDS-4075 20 1.0mH
PDS-4110 30 0.7mH
PDS-4150 40 0.53mH
380/440
PDS-4225 60 0.36mH
PDS-4300 80 0.26mH
PDS-4370 100 0.21mH
PDS-4450 120 0.18mH
PDS-4550 150 014mH
PDS-4750 200 0.11mH
Note: The A.C.L. for 220V and 380V/440V have different induction values, please do not mix up.

12
3. Control Panel
The control panel involves 4 digits 7-segment display and 4 Led-lamps, 8 keys and a potential meter (VR).
It has four possible operation modes: "CTL", "MON", "PAR" and "ALM modes, described below.
VR input is equivalent to AI3 input, JP3B of CPU board determine the AI3 input source.
3.1 CTL Mode
Push the "CTL/MON" key, will change the keypad operation between "CTL"
and "MON" Mode. If both "HZ" and "I" Led are blank, it is under "CTL"
Mode.
Under "CTL" Mode, user can control the driver running in either direction and
may modify the desired running speed.
For normal run/stop control, use only the three keys:
FWD key is used for running the driver in forward direction.
REV key is used for running the driver in reverse direction.
STOP key is used to stop the driver.
If Pr.40 = 3 or 8, the running frequency shall be modified by keypad, then
these keys are enabled:
RD/WT key is used to read out the internal Panel Speed Set value.
▲ key is used to increase the Panel Speed Set value
▼ key is used to decrease the Panel Speed Set value
STOP key is used for cursor shift.

Procedure:
a. Under normal CTL mode, push RD/WT will enter Panel Speed Set mode, (if Pr.040=8, the display will show the
value stored in Pr.000) and blinking the data.
b. Push ▲ or ▼, the display starts to show the cursor position.
c. Push ▲ or ▼, in order to modify the Panel set frequency.
d. Push CTL/MON key will go back to normal CTL mode.
Note: If Pr.40=8, the new modified Panel Speed Set value will rewrite into Pr.000 automatically.
3.2 MON mode
Push the "CTL/MON" key, will change the keypad operation between "CTL" and "MON" Mode.
Under "MON" Mode, user can control the driver running in either direction and may monitor any two internal status
easily.
If "HZ" Led is on, it is under "MON" Mode and 7-segment shows the "HZ" data. (Or the desired parameter assigned
by Pr.099)
If "I" Led is on, it is under "MON" Mode and 7-segment shows the "I" data. (Or the desired parameter assigned by
Pr.098)
FWD key is used for running the driver in forward direction.
REV key is used for running the driver in reverse direction.
STOP key is used to STOP the driver.
▲ key is used to select "HZ" or "I" data shown on the 7-segment display.
▼ key is used to select "HZ" or "I" data shown on the 7-segment display.
3.3 PAR mode
Push the "PAR/ALM" key, will change the keypad operation between "PAR" or "ALM" mode.
If push PAR/ALM key, 7-segment shows "Pr.xxx", it is under "PAR" Mode, the HZ and I lamps all ON, user can
modify or monitor all the internal Parameters. To modify any parameter, follow the steps described below:
STEP 1: push "PAR/ALM" key, the 7-segment will show "Pr.nnn". (nnn is parameter number)
STEP 2: push ▲ or ▼ key to select desired parameter number, and "STOP" key used as cursor shift.
STEP 3: push "RD/WT" key to READ the content of the specified parameter. (The 7-segment now shows the value of
this parameter.)
STEP 4: push ▲ or ▼ key to modify the displayed value, and "STOP" key used as cursor shift.
STEP 5: push "RD/WT" key to WRITE the new value into parameter memory.
STEP 6: push "PAR/ALM" repeat STEP 1~5 to modify next parameter.
3.4 ALM mode
Push the "PAR/ALM" key, will change the keypad operation between "PAR" or "ALM" mode.
If push PAR/ALM key, 7-segment shows "0.-xx", it is under "ALM" Mode.
Under "ALM" Mode, the user can execute RESET function or monitor ALARM STATUS.
STOP/RESET key, the driver will execute RESET function.
▲ and ▼ key are used to check ALARM History.

13
4. Start-Up Examples
4.1 Basic Function Block

Speed Loop Torque Limit Current loop Vq

Standard Speed Cmd uvw
Spd cmd Spd err Tcmd Iq cmd Iq err Axis Vu,Vv,Vw
Vd

Internal Speed Cmd CSW0 P-I Gain P-I Gain Vector

(position mode) Id err
Transform

Iu,Iv,Iw
Pos. err Iq fb
P-I Gain Flux Control d-q
Id cmd Axis

Id fb
Feed Forward
Position/Angle
Position Loop( P-I-F controller) Pos. fb.
Counter

Pcmd/ CSW1 Clocks to Speed

Tracking Speed Feedback Encoder Fb.
Block
Pos. cmd

Pulse cmd

Buffered Output
Increment APTP Block
Note:
CSW0: Select Position or Speed mode
Absolute APTP Block
CSW2 CSW1: Select Pcmd or APTP mode
CSW2: Select Absolute or Incremental mode

14
4.2 Setup Basic Motor Parameter
Refer to section 5.2.11 for detail description of motor parameter groups (Pr.300~499).
For example, if an induction motor running under V/F constant mode, user must set up the V/F curve parameters
according to motor manufacturer’s data.
l Select motor characteristic group#0, set Pr.188=0
l Select induction motor under V/F control mode, set Pr.300=0
l Set motor rated speed in Pr.310 (RPM)
l Set motor maximum speed in Pr.315 (RPM)
l Set motor minimum speed in Pr.316 (RPM)
l Set motor rated voltage in Pr.307 (% of Input Line Voltage)
l Set motor peak voltage in Pr.308 (% of Input Line Voltage)
l Set Boost voltage in Pr.309 (% of motor rated voltage)
l Set motor rated current in Pr.311=(MotorRatingCurrent/DriverRatingCurrent)*100%
l Set motor peak current in Pr.312=(MotorPeakCurrent/MotorRatingCurrent)*100%
l Set motor pole number in Pr.314
Vout(%)
Motor Parameter Group #0
Pr.300~Pr.349

Pr.308
Pr.307

Pr.309
Speed (rpm)
Pr.316 Pr.310 Pr.315

4.3 Default Setting of some simple Examples

For user convenience, some default setting for different application is embedded in the firmware.
Execute RESET operation after setting Pr.094 to specified value; the CPU will set related parameters to perform the
desired operation mode.
Pr.094=201, simple V/F mode operation for induction motor
Pr.094=202, simple Induction Servo running under Speed mode
Pr.094=203, simple Induction Servo running under Pcmd mode
Pr.094=204, simple Induction Servo running under Auto Point-to-Point Positioning
Pr.094=205, Auto Tuning for Induction Servo Motor
Pr.094=232, simple Brushless Servo running under Speed mode
Pr.094=233, simple Brushless Servo running under Pcmd mode
Pr.094=234, simple Brushless Servo running under Auto Point-to-Point Positioning
Pr.094=235, Auto Tuning for Brushless Servo Motor
NOTE: Before above setting, select Pr.094=1, then execute RESET to initialize the R/W type parameters to default
value. (Refer to section 5.2.3)

4.3.1 V/F Constant Mode for Induction Motor

Select Pr.094=201, then execute RESET to initialize the parameters. After initialization, the CPU loads following
parameters, then the drive standby under V/F mode.
Pr.188=0 Choose pre-stored Group#0 motor parameters (Pr.300~Pr.349)
Pr.300=0 Let the motor operate under V/F constant mode
Pr.330~Pr.333=0 Always operate under open loop speed mode
Pr.141=102 DI1(102) Drive will Enable by DI1
Pr.145=73 DI5(73) FWD RUN (effective when control by terminal input)
Pr.146=74 DI6(74) REV RUN (effective when control by terminal input)
Pr.181=0 & Pr.039=0.2 FWD/REV command by LOCAL panel normally
Pr.040=0.25 Speed command by Pr.000 normally
Pr.000=500 Default speed = 500RPM
Pr.001=5.00 5 seconds ramp up from zero to maximum speed
Pr.002=5.00 5 seconds ramp down from maximum to zero speed

15
 Procedure:
l Connect DI1 to DCOM (assume DI/DO is chosen to be SINK type) to enable the drive.
l Push FWD or REV key, then the motor speed will ramp up to 500RPM.
l Change Pr.039=2.2, transfer control to terminal input DI5 & DI6.
l Connect DI5 (or DI6) to DCOM; the motor will ramp up to 500RPM.

4.3.2 Speed Mode for Induction Servo Motor

Select Pr.094=202, then execute RESET to initialize the parameters. After initialization, the CPU loads following
parameters, then the drive standby under Speed mode.
Pr.188=0 Choose pre-stored Group#0 motor parameters (Pr.300~Pr.349)
Pr.300=2 Select Induction servo motor for close loop control *1
Pr.330=0 Select Speed control mode
Pr.331~Pr.333=0 Always operate under speed mode, no torque control
Pr.141=102 DI1(102) Drive will Enable by DI1
Pr.145=73 DI5(73) FWD RUN (effective when control by terminal input)
Pr.146=74 DI6(74) REV RUN (effective when control by terminal input)
Pr.181=0 & Pr.039=0.2 FWD/REV command by LOCAL panel normally
Pr.040=0.25 Speed command by Pr.000 normally
Pr.000=500 Default speed = 500RPM
Pr.001=5.00 5 seconds ramp up from zero to maximum speed
Pr.002=5.00 5 seconds ramp down from maximum to zero speed
Procedure:
l Try operations similar to section 4.3.1.
l Modify Pgain and Igain if necessary.
*1: before operation start, verify following parameters (refer to section 5)
Pr.302: PPR of Encoder
Pr.303: A/B clock Direction
Pr.313: Field Current%=(FieldCurrent/MotorRatedCurrent)*100%
Pr.317: Slip RPM
Pr.320: Pgain of Current loop
Pr.321: I gain of Current loop
Pr.323: P gain of Speed loop
Pr.324: I gain of Speed loop

4.3.3 Tracking Mode (Pcmd) for Induction Servo Motor

Select Pr.094=203, then execute RESET to initialize the parameters. After initialization, the CPU loads following
parameters, then the drive standby under tracking mode.
Pr.188=0 Choose pre-stored Group#0 motor parameters (Pr.300~Pr.349)
Pr.300=2 Select Induction servo motor for close loop control
Pr.330=1 Position control *2
Pr.331=1 Tracking mode by Pulse Command input from XY port
Pr.332~Pr.333=0 No torque control
Pr.141=102 DI1(102) Drive will Enable by DI1
Pr.145=73 DI5(73) FWD RUN (effective when control by terminal input)
Pr.146=74 DI6(74) REV RUN (effective when control by terminal input)
Pr.181=0 & Pr.039=0.2 FWD/REV command by LOCAL panel normally
Pr.040=0.25 Speed command by Pr.000 normally
Pr.000=500 Default speed = 500RPM
Pr.130=0 select quadrature input clock to XY input
Pr.133=1000 XY multiply rate =1000
Pr.134=1000 XY division rate = 1000
*2: before operation start, verify Pr.326 (Position loop P gain) and the parameters of *1 of section 4.3.2.
Procedure:
l Connect DI1 to DCOM
l Push FWD or REV key, then the drive is ready to accept clock input from XY port
l Change Pr.133 or Pr.134, and verify the effects.

16
4.3.4 Auto Point-to-Point control Mode for Induction Servo
Select Pr.094=204, then execute RESET to initialize the parameters. After initialization, the CPU loads following
parameters, then the drive standby under auto point-to-point mode.
Pr.188=0 Choose pre-stored Group#0 motor parameters (Pr.300~Pr.349)
Pr.300=2 Select Induction servo motor for close loop control
Pr.330=1 Position control (Refer to section 4.3.3 *2)
Pr.331=0 Auto Point-to-Point control
Pr.332=0 Select Incremental type APTP
Pr.333=0 No torque control
Pr.141=102 DI1(102) Drive will Enable by DI1
Pr.142=128 DI2(128) Start Home search
Pr.143=129 DI3(129) End Home search and stop at the desired offset point
Pr.144=118 DI4(118) APTP start trigger
Pr.145=119 DI5(119) Direction control
Pr.146=120 DI6(120) Point selection Bit0
Pr.181=0 & Pr.039=0.0 FWD/REV command by LOCAL panel normally
Pr.040=0.00 Speed command by Pr.000 normally
Pr.000=500 Default speed = 500RPM
Pr.001=0.50 0.5 seconds ramp up from zero to maximum speed
Pr.002=0.50 0.5 seconds ramp down from maximum to zero speed
Pr.568/569=00000001 Offset one clock after index catch
Pr.500/501=4*PPR One revolution when DL0 is selected
Pr.502/503=40*PPR Ten revolutions when DL1 is selected
Procedure:
l Connect DI1 to DCOM
l Push FWD or REV key, then the drive is ready to accept Home Search Command
l Trigger DI2, the motor start run to 500RPM
l Trigger DI3 (assume DOG sensor input), the drive start search index then stop at desired offset
l Use DI5 and DI6 to select desired DLn (Destination Length) and direction
l Trigger DI4, the motor run and stop at DLn.
l Try to use DI7~DI10 and set other DLn parameters to select different length.
l If Absolute type APTP is desired, set Pr.332=1, execute RESET, then try again

4.3.5 Example for Brushless Servo Motor

If select Pr.094=232~234, the functions are similar to Pr.094=202~204, Except
l Pr.188=3, the motor characteristic parameters are default to group#3(Pr.450~Pr.499)
l Pr.450=3, select brushless servo motor.
*User has to prepare other parameters in group#3 to match the brushless motor in use.

17
4.4 Auto Tuning for Servo Motors
4.4.1 Auto Tuning for Induction Servo Motor
If select Pr.094=205, only few parameters is necessary to set by user, then after execute RESET, this drive can detect
the motor characteristic parameters itself.
For induction servo, use motor parameter group#0(Pr.300~Pr.349).
1. Set Pr.307=Rated motor Voltage=100%(Motor Rated Voltage/Line Voltage).
2. Set Pr.310=Rated motor Speed (RPM).
3. Set Pr.311=Rated motor Current=100%*(Motor Rated Current/Driver Rated Current).
4. Set Pr.094=205, inform the drive to execute Auto tuning after reset
5. Execute RESET to initiate Tuning Process.
After tuning process complete, the drive will set Pr.094=202, then reset again in order to preload the drive as
speed controller. (Refer to sec.4.3.2). The following parameters will be changed after tuning process, user should
verify again.
Pr.302- Encoder PPR, set to correct value
Pr.303- Encoder Direction, set to correct direction
Pr.308- Set equal to Pr.307
Pr.309- Boost Voltage (used when V/F control application)
Pr.312- Peak Current, set to 100%
Pr.313- Field Current, set to proper value (% of Motor Rated Current)
Pr.314- Pole, set to correct pole number
Pr.315- Maximum Speed, Set equal to Pr.310
Pr.316- Minimum Speed, set to 0RPM
Pr.317- SLIP RPM, set to 5% of Rated motor Speed(RPM)
Pr.320- ACR Pgain, Set to proper value
Pr.321- ACR I gain, Set to proper value
Pr.323- ASR Pgain, Set to proper value
Pr.324- ASR Igain, Set to proper value
4.4.2 Auto Tuning for Brushless Servo Motor
If select Pr.094=235, only few parameters is necessary to set by user, then after execute RESET, this drive can detect
the motor characteristic parameters itself.
For brushless servo, use motor parameter group#3(Pr.450~Pr.499).
1. Set Pr.460=Rated motor Speed (RPM).
2. Set Pr.461=Rated motor Current=100%*(Motor Rated Current/Driver Rated Current).
3. Set Pr.094=235, inform the drive to execute Auto tuning after reset
4. Execute RESET to initiate Tuning Process.
After tuning process complete, the drive will set Pr.094=232, then reset again in order to preload the drive as
speed controller. (Refer to sec.4.3.5). The following parameters will be changed after tuning process, user should
verify again.
Pr.452- Encoder PPR, set to correct value
Pr.453- Encoder Direction, set to correct direction
Pr.457-Rated motor Voltage, set to proper value
Pr.458- Set equal to Pr.457
Pr.459- Boost Voltage=0
Pr.462- Peak Current, set to 100%
Pr.463- Field Current=0
Pr.464- Pole, set to correct pole number
Pr.465- Maximum Speed, Set equal to Pr.460
Pr.466- Minimum Speed, set to 0RPM
Pr.467- SLIP RPM=0
Pr.470- ACR Pgain, Set to proper value
Pr.471- ACR I gain, Set to proper value
Pr.473- ASR Pgain, Set to proper value
Pr.474- ASR Igain, Set to proper value
4.4.3 Auto Tuning Resolver BL Servo Motor
If the servo motors use resolver as feedback element, then user must select resolver option card. After choosing correct
feedback option card, then the drive will identify itself for controlling the resolver.
Auto tuning procedure and all parameters setting are the same as those described in section 4.4.2, except:
l Pr.340/390/440/490 Resolver Angle Shift, it defines the angle shift between motor magnetic North direction and
resolver North mark.
l Pr.341/391/441/491 Resolver Polarity, it defines the polarity of Sine Cosine signal.
18
5. Parameters
5.1 Parameter List
Pr.xxx Parameter Name Default Min. Max. Type Reference
000 Main Speed Set 0 rpm 0 9000 R/W
001 Main Acceleration Time 5.00 sec 0.00 650.00 R/W 5.2.4
002 Main Deceleration Time 5.00 sec 0.00 650.00 R/W
005 Brake Speed 5 rpm 0 9000 R/W 5.2.5
012 PWM Carrier 8.0 KHz 8.0 8.0 R 5.2.7
013 Alarm Code 0 0 9 M 5.2.8
019 Jog Speed 10 rpm 0 9000 R/W
5.2.4
020 Jog Acceleration/Deceleration Time 5.00 sec 0.00 650.00 R/W
021 SPD1 Speed Set 0 rpm 0 9000 R/W
022 SPD1 Acceleration Time 5.00 sec 0.00 650.00 R/W 5.2.4
023 SPD1 Deceleration Time 5.00 sec 0.00 650.00 R/W
024 SPD2 Speed Set 0 rpm 0 9000 R/W
025 SPD2 Acceleration Time 5.00 sec 0.00 650.00 R/W 5.2.4
026 SPD2 Deceleration Time 5.00 sec 0.00 650.00 R/W
027 SPD3 Speed Set 0 rpm 0 9000 R/W
028 SPD3 Acceleration Time 5.00 sec 0.00 650.00 R/W 5.2.4
029 SPD3 Deceleration Time 5.00 sec 0.00 650.00 R/W
031 Reverse Inhibit 0 0 1 R/W 5.2.5
033 Discharge Enable 0 0 2 R/W 5.2.5
034 UP/OP Restart Enable 0 0 1 R/W 5.2.5
039 Control Command Select 0.0 0.0 9.9 R/W 5.2.5
040 Speed Source Select 8.08 0.00 99.99 R/W SEC. 6
048 Detect Irms 100 % 0 250 FR/W 8.3.4
049 Detect RPM 300 rpm 0 9000 FR/W
8.3.1
050 Detect Tolerance 30 rpm 0 9000 FR/W
051 Thermal Trip Time 3 sec 0 120 R/W 5.2.5
053 Gear Ratio 100.00 % 0.00 600.00 R/W 5.2.8
054 Irms Select 0 0 255 R/W 5.2.8
057 HZ Hz M
058 RPM rpm 0 9000 M
059 Vdc (Capacitor) Volts DC M
5.2.8
060 Vout (r.m.s. output) Volts AC M
061 Irms Amp M
062 Temperature ℃ 0 100 M
064 DI0~DI14 Input Status 0000 Hex 0000 7FFF M
5.2.8
065 DO0~DO6 Output Status 0000 Hex 0000 007F M
066 DI0~DI10 Simulation 0 0 2047 RAM 5.2.5
067 Torque Set (RAM) 0.00% 0.00 100.00 RAM 5.2.5
068 DO Simulation 0 0 128 RAM 5.2.5
069 Torque Set (EAROM) 0% 0 100 FR/W 5.2.5
070 Analog Input Gain 50% 0 100 R/W 6.2.4
071 Timer(1) Time 5.0 sec 0.1 6553.0 R/W
7.3.3
072 Timer(2) Time 5.0 sec 0.1 25.0 R/W
073 S-curve Time T1 0.00 sec 0.00 2.50 R/W
074 S-curve Time T2 0.00 sec 0.00 2.50 R/W
5.2.4
075 S-curve Time T3 0.00 sec 0.00 2.50 R/W
076 S-curve Time T4 0.00 sec 0.00 2.50 R/W
077 DO1 Pulse Output Ratio 1 1 100 R/W 8.3.3
083 IGBT Guard Time 3.0μsec 2.0 25.0 FR/W 5.2.7
084 Line Voltage Volts AC 40 1000 FR/W 5.2.7
085 Rated Current Amp 0.5 3000.0 FR/W 5.2.7
086 Irms Adjust % 70 140 FR/W
5.2.7
087 Vdc Adjust % 70 140 FR/W
089 AI1 Low 12 0 1023 FR/W
5.2.6
090 AI1 High 1012 0 1023 FR/W
091 AI2 Low 12 0 1023 FR/W 5.2.6
19
Pr.xxx Parameter Name Default Min. Max. Type Reference
092 AI2 High 1012 0 1023 FR/W
094 Reload Parameter 0 0 250 R/W 5.2.3
095 Memory Protect 0 0 1 R/W
5.2.2
096 Factory Write Enable 0 0 1 R/W
097 Version R 5.2.7
098 Monitor(I) 61 0 999 R/W
5.2.8
099 Monitor(HZ) 58 0 999 R/W
108 Counter Value 0 0 9999 M 7.3.3
109 Counter Set 0 0 9999 R/W DIx(28)
116 Speed Set 0 rpm 0 9000 RAM 5.2.4
120 Protocol Select 0 0 3 FR/W
121 Baud Rate 2 0 3 FR/W
122 Stop Bit 1 0 1 FR/W
SEC. 9
123 ID 1 1 250 FR/W
124 Queue Status 0 0 31 M
125 Parity 0 0 2 FR/W
130 XY Clock Type Select 0 0 6 FR/W
131 XY Input Pin Status 0.0. 0.0. 1.1. M
132 XY Direction Change 0 0 1 FR/W
133 XY Multiply Rate 0 1000 0 9999 FR/W
134 XY Division Rate 0 1000 0 9999 FR/W
5.2.9
135 XY Multiply Rate 1 1000 0 9999 FR/W
136 XY Division Rate 1 1000 0 9999 FR/W
137 XY Counter Value 0000 Hex 0000 FFFF M
138 XY Sampling Period 50 mSec 2 250 FR/W
139 XY Rate 0000 Hex 0000 FFFF M
140 DI0 Select 0 0 250 R/W
141 DI1 Select 0 0 250 R/W
142 DI2 Select 0 0 250 R/W
143 DI3 Select 0 0 250 R/W
144 DI4 Select 0 0 250 R/W
145 DI5 Select 0 0 250 R/W
146 DI6 Select 0 0 250 R/W
147 DI7 Select 0 0 250 R/W SEC .7
148 DI8 Select 0 0 250 R/W
149 DI9 Select 0 0 250 R/W
150 DI10 Select 0 0 250 R/W
151 DI11 Select 0 0 250 R/W
152 DI12 Select 0 0 250 R/W
153 DI13 Select 0 0 250 R/W
154 DI14 Select 0 0 250 R/W
157 Line Speed(1) 0 0 65530 M
158 Line Speed(2) 0.00 0.00 655.30 M 5.2.8
159 Line Speed(3) 0.0 0.0 6553.0 M
160 DO0 Select 0 0 250 R/W
161 DO1 Select 0 0 250 R/W
162 DO2 Select 0 0 250 R/W
SEC. 8
163 DO3 Select 0 0 250 R/W
164 DO4 Select 0 0 250 R/W
165 DO5 Select 0 0 250 R/W
166 DO6 Select 0 0 250 R/W
180 Fan Control 10.50 sec 5.00 99.99 FR/W 5.2.5
181 Panel Command Priority 0 0 1 FR/W 5.2.5
182 Panel Speed Priority 0 0 1 FR/W 5.2.5
186 Write Select 0 0 1 RAM 5.2.5
188 Motor Parameter Group Select 0 0 3 FR/W 5.2.5
189 PG Loss Check Enable 1 0 1 FR/W 5.2.5
191 AI3 Low 12 0 1023 FR/W
5.2.6
192 AI3 High 1012 0 1023 FR/W
193 Home Direction 1 0 19 FR/W 5.2.12

20
 Pr.xxx Parameter Name Default Min. Max. Type Reference
194 Home Speed and Acc/Dec 0 0 1 FR/W
195 Travel Limit 0 0 1 R/W 5.2.12
200 Iv A/D Value 0 1023 M
201 AI1 A/D Value 0 1023 M
202 AI2 A/D Value 0 1023 M
5.2.8
203 AI3 A/D Value 0 1023 M
204 Iw A/D Value 0 1023 M
205 Idc A/D Value 0 1023 M
206 Vcap A/D Value 0 1023 M
5.2.8
207 Temperature A/D Value 0 1023 M
210 AO1 Select 0 0 250 FR/W
211 AO1 Zero 0.00 0.00 1.99 FR/W 5.2.6
212 AO1 Span 100.0% 0.0 150.0 FR/W
220 AO2 Select 0 0 250 FR/W
221 AO2 Zero 0.00 0.00 1.99 FR/W 5.2.6
222 AO2 Span 100.0% 0.0 150.0 FR/W
230 AO3 Select 0 0 250 FR/W
231 AO3 Zero 0.00 0.00 1.99 FR/W 5.2.6
232 AO3 Span 100.0% 0.0 150.0 FR/W
240 PID Input Select 0.00 0.00 99.99 FR/W
241 PID Default Configuration 0 0 63 FR/W
242 PID Output Value 0000 0000 FFFF M
243 PID Pgain 0 0 9999 FR/W
244 PID Igain 0 0 9999 FR/W
245 PID Dgain 0 0 9999 FR/W
246 PID FBgain 1.00 0.00 100.00 FR/W
5.2.10
247 PID Constant Reference 0.0 0.0 100.0 FR/W
248 PID Limit 100.0 0.0 100.0 FR/W
249 PID Dtime 0.00 sec 0.00 2.50 FR/W
250 PID Set Value 0000 Hex 0000 FFFF M
251 PID FB Value 0000 Hex 0000 FFFF M
252 PID Error Value 0000 Hex 0000 FFFF M
253 PID Auto Gain Select 0 0 7 FR/W
300, 350, 400, 450 Motor Type Select 0 0 5 FR/W
301, 351, 401, 451 ABC Status 0.0.0. 0.0.0 1.1.1. M
302, 352, 402, 452 Encoder PPR 1024 0 9999 FR/W
303, 353, 403, 453 A-Lead/Lag-B 0 0 1 FR/W
304, 354, 404, 454 AB Filter 2 0 5 FR/W
305, 355, 405, 455 AB Counter 0000 Hex 0000 FFFF M
306, 356, 406, 456 UVW Status 0.0.0. 0.0.0. 1.1.1. M
307, 357, 407, 457 Motor Rated Voltage 100% 0 100 FR/W
308, 358, 408, 458 Motor Peak Voltage 100% 0 100 FR/W
309, 359, 409, 459 Boost Voltage 0.0% 0 25.0 FR/W
310, 360, 410, 460 Motor Rated RPM 1800 rpm 0 9000 FR/W
311, 361, 411, 461 Motor Rated Current 100% 10 100 FR/W
312, 362, 412, 462 Motor Peak Current 100% 0 300 FR/W
313, 363, 413, 463 Field Current 20% 0 100 FR/W 5.2.11
314, 364, 414, 464 Pole 4 2 250 FR/W
315, 365, 415, 465 Maximum RPM 1800 rpm 100 9000 FR/W
316, 366, 416, 466 Minimum RPM 0 rpm 0 9000 FR/W
317, 367, 417, 467 Slip RPM 100 rpm 0 9000 FR/W
318, 368, 418, 468 Encoder PPR Check 0000 Hex 0000 FFFF M
319, 369, 419, 469 Reserve for special function 0
320, 370, 420, 470 P Gain (Current Loop) 50 0 2000 FR/W
321, 371, 421, 471 I Gain (Current Loop) 50 0 2000 FR/W
322, 372, 422, 472 Reserve for special function 0
323, 373, 423, 473 P Gain (Speed Loop) 500 0 4000 FR/W
324, 374, 424, 474 I Gain (Speed Loop) 50 0 2000 FR/W
325, 375, 425, 475 Reserve for special function 0
326, 376, 426, 476 P Gain (Position Loop) 200 0 2000 FR/W

21
 Pr.xxx Parameter Name Default Min. Max. Type Reference
327, 377, 427, 477 Reserve for special function 0
328, 378, 428, 478 Reserve for special function 0
329, 379, 429, 479 Reserve for special function 0
330, 380, 430, 480 Position/Speed Select 0 0 1 FR/W
331, 381, 431, 481 Pcmd/APTP Select 0 0 1 FR/W
332, 382, 432, 482 Absolute/Increment Select 0 0 1 FR/W
333, 383, 433, 483 Torque Limit Source Select 0.0 0 9.9 FR/W
334, 384, 434, 484 Length Conversion 0 0 16 FR/W
335, 385, 435, 485 Length Compensation 0 0 1 FR/W 5.2.11
336, 386, 436, 486 Compensation Polarity 0 0 1 FR/W
337, 387, 437, 487 Reserve for special function 0
338, 388, 438, 488 Reserve for special function 0
339, 389, 439, 489 Reserve for special function 0
340, 390, 440, 490 Resolver Shift Angle 0.0 0.0 1000.0 FR/W
341, 391, 441, 491 Resolver Polarity 0 0 1 FR/W
342, 392, 442, 492 BL Motor Select 0 0 1 FR/W
343, 393, 443, 493 Direct Torque Control Select 0 0 1 FR/W
344, 394, 444, 494 APTP S Ramp Select 0 0 1 FR/W 11.1.3
345, 395, 445, 495 Reserve for special function 0
346, 396, 446, 496 Reserve for special function 0
347, 397, 447, 497 Reserve for special function 0
348, 398, 448, 498 Reserve for special function 0
349, 399, 449, 499 Reserve for special function 0
501 DL0 (Low) 0 0 9999 FR/W
502 DL0 (High) 0 0 9999 FR/W
502 DL1 (Low) 0 0 9999 FR/W
503 DL1 (High) 0 0 9999 FR/W
504 DL2 (Low) 0 0 9999 FR/W
505 DL2 (High) 0 0 9999 FR/W
﹕ ﹕ ﹕ ﹕ ﹕ ﹕
﹕ ﹕ ﹕ ﹕ ﹕ ﹕ 5.2.12
﹕ ﹕ ﹕ ﹕ ﹕ ﹕
558 DL29 (Low) 0 0 9999 FR/W
559 DL29 (High) 0 0 9999 FR/W
560 DL30 (Low) 0 0 9999 FR/W
561 DL30 (High) /AI1 Detect Level 0 0 9999 FR/W
562 DL31 (Low) /AI2 Detect Level 0 0 9999 FR/W
563 DL31 (High) /AI3 Detect Level 0 0 9999 FR/W
564 Forward Travel Limit (Low) 0 0 9999 FR/W
5.2.12
565 Forward Travel Limit (High) 0 0 9999 FR/W
566 Reverse Travel Limit (Low) 0 0 9999 FR/W
5.2.12
567 Reverse Travel Limit (High) 0 0 9999 FR/W
568 Index Offset (Low) 0 0 9999 FR/W
5.2.12
569 Index Offset (High) 1 0 9999 FR/W
570 Position Error Limit 1000 0 9999 FR/W
5.2.12
571 In Position Range 10 0 9999 FR/W
574 μm Display BCD (Low) 0 0 9999 M
5.2.8
575 μm Display BCD (High) 0 0 9999 M
576 μm Revolution (Low) 0 0 9999 FR/W
5.2.12
577 μm Revolution (High) 0 0 9999 FR/W
578 Position BCD (Low) 0 0 9999 M
5.2.8
579 Position BCD (High) 0 0 9999 M
580 Position Hex (Low) 0000 Hex 0000 FFFF M
5.2.8
581 Position Hex (High) 0000 Hex 0000 FFFF M
582 μm Display Hex (Low) 0000 Hex 0000 FFFF M 5.2.8
583 μm Display Hex (High) 0000 Hex 0000 FFFF M
734 Last Length μm Display Hex (Low) 0000 Hex 0000 FFFF M
11.1.3
735 Last Length μm Display Hex (High) 0000 Hex 0000 FFFF M

22
5.2 Parameter Description
5.2.1 Parameter Type
Type Description
R/W Type R/W parameters are stored in EAROM. They can be read/write and story in the memory permanently.
Type FR/W parameters are stored in EAROM. Generally, they are used for factory adjustment.
FR/W
Only authorized engineers should modify them.
RAM Type RAM parameters are store in RAM; they will be changed to default after RESET or power off.
M Type M is read only parameters for monitoring.
R Type R is constant parameters.
5.2.2 Parameter Protection
Pr.nnn Parameter Name Description
095 Memory Protect
Pr.095 Pr.096 Description
096 Factory Write Enable
1 -- All parameters (except Pr.000 and Pr.095) are not allow to change.
0 1 Parameters with R/W and FR/W type can be changed.
0 0 Parameters with R/W type can be changed..
186 Write Select
Pr.186 Description
0 Any further parameter change will write to EAROM.
Any further parameter change will write to RAM only, they will
1
be changed to original value after RESET or power off..
5.2.3 Parameter Initalization
Pr.nnn Parameter Name Description
094 Reload Parameter Pr.094 is used for Parameter Initialization..
Follow the process to execute R/W type parameters initalization:
l Write Pr.095 = 0, and Pr.094＝1.
l Execute “ALM” RESET (press STOP/RESET key under “ALM” mode),
or Execute Hardware RESET,
or Execute Power-On RESET
l After initialization process, the data of parameters with R/W type will change to
DEFAULT value listed in the PARAMETER LIST table (section 5.1).
Follow the process to execute all parameters initalization:
l Write Pr.094 =249
l Execute “ALM” RESET (press STOP/RESET key under “ALM” mode),
or Execute Hardware RESET,
or Execute Power-On RESET
l After initialization process, all of data in EAROM memory will change to
DEFAULT value listed in the PARAMETER LIST table (section 5.1).
Refer to section 4.2 for default setting of different application.
5.2.4 Speed & Acceleration/Deceleration Time
Pr.nnn Parameter Name Description
000 Main Speed Set
001 Main Acceleration Time Pr.027 SPD3 Speed
002 Main Decel Time Normal Speed
019 Jog Speed
Pr.021 SPD1 Speed
019 Jog Speed
020 Jog Accel/Decel Time Pr.024 SPD2 Speed
021 SPD1 Speed Pr.019 JOG Speed time
022 SPD1 Acceleration Time
023 SPD1 Deceleration Time
DIx(5) JOG
024 SPD2 Speed
025 SPD2 Acceleration Time
026 SPD2 Deceleration Time
DIx(4) SPD1
027 SPD3 Speed
028 SPD3 Acceleration Time
DIx(3) SPD2
029 SPD3 Deceleration Time DIx(2) SPD3

DIx(73) RUN time

23
 l Normal Speed: speed source defined in Pr.040.
l Acceleration Time: the period of time from 0 rpm ramp up to Maximum RPM.
l Deceleration Time: the period of time from Maximum RPM ramp down to 0rpm.
l The priority level for multi-speed operation is:
JOG＞SPD1＞SPD2＞SPD3＞16 STEP＞NORMAL SPEED
l When normal speed selected, Pr.001/002 determines the acceleration and
deceleration time.
l When JOG speed selected, Pr.020 determines the acceleration and deceleration
time
l When SPD1 speed selected, Pr.022 determines the acceleration and Pr.023
determines the deceleration time.
l When SPD2 speed selected, Pr.025 determines the acceleration and Pr.026
determines the deceleration time.
l When SPD2 speed selected, Pr.028 determines the acceleration and Pr.029
determines the deceleration time.
When DIX(2)~DIx(5) are all OFF (no JOG, SPD1, SPD2, SPD3 function),
DIx(80)~DIx(83) are used to assign 16-STEP speed , DIx(84)~DIx(87) can be used to
select acceleration and deceleration time.
l If any of DIx(80)~DIx(83) is ON, then set speed is:
Set Speed = DIx(83)*Pr.027+DIx(82)*Pr.024+DIx(81)*Pr021+DIx(80)*Pr.019
l When DIx(84) is ON, Pr.020 determines the acceleration and deceleration time
l When DIx(85) is O, Pr.022 determines the acceleration and Pr.023 determines
the deceleration time.
l When DIx(86) is ON, Pr.025 determines the acceleration and Pr.026 determines
the deceleration time
l When DIx(87) is ON, Pr.028 determines the acceleration and Pr.029 determines
the deceleration time.
S-curve Time T1 By setting an S-curve value, will smooth the motor transition at beginning and end of
073
(Begin Acceleration) the acceleration and deceleration period from current running speed to another
S-curve Time T2 operation speed.
074
(End Acceleration) Speed
S-curve Time T3
075
(Begin Deceleration)
076 S-curve Time T4
(End Deceleration)

Acceleration

T3 T4

T1 T2

116 Speed Set The Speed Set memorized in RAM not store to EAROM.
If Speed Source select Pr.040= 46, this parameter will be used as the desired speed
source. Usually, use this for speed setting by communication and the application has
to change speed often.

5.2.5 Control Function

Pr.nnn Parameter Name Description
005 Brake Speed While deceleration to stop, if the output speed is lower than this parameter, the output
speed change to 0 RPM directly.
031 Reverse Inhibit
Pr.031 Description
0 Drive may run in both direction
1 Reverse run is inhibited.

24
033 Discharge Enable
Pr.033 Description
0 Discharge circuit is Disabled.
The discharge transistor will ON if the following conditions are met:
l Drive is Running
1 l Drive has no Alarm
l Vdc > Pr.084 * 1.414 * 117%
l Drive under deceleration
The discharge transistor will ON if the following conditions are met:
l Drive is Running
2
l Drive has no Alarm
l Vdc > Pr.084 * 1.414 * 117%
034 UP/OP Restart Enable
Pr.034 Description
0 UP/OP Restart function is Disabled.
After UP/OP alarm, when power comes back normal, the drive will
1
restart automatically.
039 Control Command Select This parameter is select the control command will come from panel or terminal.
If the control command come from terminal, then the terminals RUN DIx(73) and
REV DIx(74) are used to control the drive.
l Any digital input terminal assigned as DIX(73) will function as RUN terminal
input.
l Any digital input terminal assigned as DIX(74) will function as REV terminal
input.
Pr.039 Description
Control command comes from the Control Panel.
l Push FWD key, the drive will run forward direction.
0
l Push REV key, the drive will run reverse direction.
l Push STOP key, the drive will stop.
The RUN terminal DIx(73) determines the drive running or stop.
1
The REV terminal DIx(74) determines the running direction.
The RUN terminal DIx(73) is equivalent to FORWARD-RUN
2
The REV terminal DIx(74) is equivalent to REVERSE-RUN
Control command come from digital input terminal:
Pr.039 RUN REV Function
OFF --- STOP
1 ON OFF FORWARD RUN
ON ON REVERSE RUN
OFF OFF STOP
2 OFF ON REVERSE RUN
ON --- FORWARD RUN
Control command select Pr.039 = a.b, it is composed of two selection of “a” and
“b” in one parameter, if DIx(89)(Control Command SW) or DIx(90)(Speed &
Control SW) is ON, then control command select = “b”, otherwise control
command select = “a”.
051 Thermal Trip Time This parameter defines the OVER LOAD trip time of Internal Thermal Relay.
If Pr.051=0, the Thermal Relay function is disabled.
(Irms/Motor Rated Current)
200%
150%
110%

Time
Pr.051
066 DI0~DI10 Simulation This parameter is used for simulating the digital input signal from DI0~DI10 terminal.
The input value is in BCD format; it is converted into Binary form to simulate each
digital input. For example:
If Pr.066=2(BCD)=00000000010(Binary), means DI1 ON.
If Pr.066=42(BCD)=00000101010(Binary), means DI1, DI3 and DI5 ON.

25
 067 Torque Set (RAM) l If Pr.333/383/433/483 (Torque Limit Source Select) = 4, the torque limit is
069 Torque Set (EAROM) controlled by Pr.067.
l If Pr.333/383/433/483 (Torque Limit Source Select) = 6, the torque limit is
controlled by Pr.069.
The difference of Pr.067and Pr.069 is:
Pr. Type Range
Pr.067 RAM 0.00~100.00%
Pr.069 FR/W 0~100%
068 DO Simulation This Parameter is used for simulating the digital output status.
The input value is in BCD format; it converted into Binary form to simulate each
digital output. For example:
Pr.068=2(BCD)= 0000010(Binary), means DO1 ON.
Pr.068=42(BCD)= 0101010(Binary), means DO1, DO3 and DO5 ON.
180 Fan Control When temperature ≧ 45˚C, Fan always ON.
Pr.180 = aa.bb, it is composed of two selection of “aa” and “bb” in one parameter,
when temperature < 45˚C, ON/OFF duty of fan is:
aa: ON time (seconds)
bb: OFF time (seconds)
181 Panel Command Priority
Pr.181 Control Command
0 From Control Panel
1 From RS485 communication port
182 Panel Speed Priority
Pr.182 Speed Command
0 From Control Panel
1 From RS485 communication port
188 Motor Parameter Group If none of all DIx select DIx(114)(MSB0) or DIx(115)(MSB1), then Motor Parameter
Select Group is selected by Pr.188
Pr.188 Motor Parameter Group
0 Use motor parameter group #0 (Pr.300~349)
1 Use motor parameter group #1 (Pr.350~399)
2 Use motor parameter group #2 (Pr.400~449)
3 Use motor parameter group #3 (Pr.450~499)
If there exists any DIx(114)(MSB0) or DIx(115)(MSB1) selected, then Motor
Parameter Group is selected by Digital Input Terminal.
DIx(114) MSB0 DIx(115) MSB1 Motor Parameter Group
OFF OFF Use motor parameter group #0 (Pr.300~349)
OFF ON Use motor parameter group #1 (Pr.350~399)
ON OFF Use motor parameter group #2 (Pr.400~449)
ON ON Use motor parameter group #3 (Pr.450~499)
NOTE: This function in checked only when power ON or after reset.
189 PG Loss Check Enable
Pr.189 Description
0 No PG Loss check
PG Loss Check enabled.
1
When PG Loss, shown alarm message “PG” on control panel.

5.2.6 Analog Input/Output Function

Pr.nnn Parameter name Description
089 AI1 Low This parameter is used to record the A/D converter data read from Pr.201 when
“AI1” input terminal is connected to “ACOM” terminal. (AI1 select 0~ +5)
090 AI1 High This parameter is used to record the A/D converter data read from Pr.201 when
“AI1” input terminal is connected to “+5V” voltage source. (AI1 select 0~ +5)
091 AI2 Low This parameter is used to record the A/D converter data read from Pr.202 when
“AI2” input terminal is connected to “ACOM” terminal. (AI2 select 0~ +5)
092 AI2 High This parameter is used to record the A/D converter data read from Pr.202 when
“AI2” input terminal is connected to “+5V” voltage source. (AI2 select 0~ +5)
191 AI3 Low This parameter is used to record the A/D converter data read from Pr.203 when
“AI3” input terminal is connected to “ACOM” terminal. (AI3 select 0~ +5)
192 AI3 High This parameter is used to record the A/D converter data read from Pr.203 when
“AI3” input terminal is connected to “+5V” voltage source. (AI3 select 0~ +5)

26
 210 AO1 Select
Setting Analog Output Function
220 AO2 Select
0 0V
230 AO3 Select
1 Positive Maximum (about 10V)
2 Negative Maximum (about –10V)
3 Speed (Full-scale=Maximum RPM)
4 abs(Speed) (Full-scale=Maximum RPM)
5 Output Current (Full-scale=200% of Drive Rated Current)
6 Output Current (Full-scale=300% of Motor Rated Current)
7 PID Output
8 Torque (Full-scale=Maximum Torque)
9 abs(Torque) (Full-scale=Maximum Torque)
12 Position Error (Full-scale= Position Error / Position Error Limit Pr.570)
211 AO1 Zero
Setting Description
221 AO2 Zero
0.00~0.99 Positive Zero Compensation (resolution 0.01 volt)
231 AO3 Zero
1.00~1.99 Negative Zero Compensation (resolution 0.01 volt)
212 AO1 Span
222 AO2 Span Analog output span adjustment
232 AO3 Span

5.2.7 Factory Adjustment Parameters

NOTE: Only authorized engineers should modify these parameters.
Pr.nnn Parameter Name Description
012 PWM Carrier Fixed frequency 8K Hz
IGBT Guard Time This parameter defines the guard time for preventing IGBT short between upper and lower
083
arm. Only factory can modify this parameter, consult factory if modification is necessary.
084 Line Voltage This parameter defines the normal working voltage of the drive.
According to this parameter, the drive calculates all voltage dependent values.
l OP Trip Voltage (Vdc) = 1.414 ＊ Pr.084 ＊ 130 ％
l UP Trip Voltage (Vdc) = 1.414 * Pr.084 * 70%
l OP Recover Voltage (Vdc) = 1.414 * Pr.084 * 120%
l UP Recover Voltage (Vdc) = 1.414 * Pr.084 * 80%
l Contactor ON Voltage (Vdc)＝1.414＊Pr.084＊69％
l Contactor OFF Voltage (Vdc)＝1.414＊ Pr.084＊65％
Note: The “contactor” means the device used to BY-PASS the charging resistor. It may
a RELAY or a SCR instead.
l Discharge Start Voltage (Vdc)＝1.414＊Pr.084＊117％ (Refer to Pr.033)
085 Rated Current This parameter defines the rated output current of the drive.
086 Irms Adjust This parameter is used to adjust the Irms data reading.
087 Vdc Adjust This parameter is used to adjust the reading of internal DC BUS.
097 Version This parameter is indicating the software revision of this drive.

5.2.8 Monitor Function

Pr.nnn Parameter Name Description
013 Alarm Code Display the present alarm message.
Alarm Code Control Panel shows Message Description
0 no Normal
1 PG PG Loss
3 OC Over Current
4 OH Over Heat
5 OP Over Voltage
6 UP Under Voltage
7 OL Over Load
9 SE CPU Program Check Sum Error
057 HZ Monitors the output frequency of the drive.
058 RPM For close loop control mode, monitors the motor rotating speed.
For V/F constant mode, RPM = 120 * Hz / POLE.
059 Vdc (Capacitor) Monitors the internal DC BUS voltage of the drive, Vdc = 1.414 * Vac (line input)
060 Vout (r.m.s. output) Monitors the output Vrms of the drive.

27
054 Irms Select Use Pr.054 to select the data type displays in Pr.061.
061 Irms Pr.054 Pr.061
0 Output Current Irms (Amp)
1 Output Current Irms (% of Drive rating)
2 Output Current Irms (% of motor rating)
11 OL accumulation level
28 abs(Output Torque) (% of Maximum Output Torque)
062 Temperature Monitors the temperature of internal heat sink. When the temperature exceeds
80 ˚C driver will STOP and show OH alarm.
064 DI0~DI14 Input Status Monitors the DI0~DI14, expressed in Hex form.
It is converted into Binary form to show the status of DI0~DI14. For example:
If Pr.064=0062(Hex)=00001100010(Binary), means DI1, DI5 and DI6 is ON.
065 DO0~DO6 Output Status Monitors the DO0~DO60, expressed in Hex form.
It is converted into Binary form to show the status of DO0~DO6. For example:
If Pr.065=0062(Hex)=1100010(Binary), means DO1, DO5 and DO6 is ON.
098 Monitor(I) While control panel is under “MON” mode, user can select which two statuses are to
099 Monitor(HZ) be monitored.
Pr.098 is used to assign the parameter to be monitored when “I” LED is ON.
Pr.099 is used to assign the parameter to be monitored when “HZ” LED is ON.
For example, the default value in Pr.099=58 and Pr.098=61, that means, the panel will
show the value of Pr.058 (rpm) while “HZ” LED is ON. And push ▲ or ▼ key to
change to LED “I” ON, the panel will show the value of Pr.061 (Irms).
053 Gear Ratio According to Pr.053, the drive calculates Line Speed show in Pr157~159.
157 Line Speed(1) Pr.xxx Display Data Range
158 Line Speed(2) 157 RPM(Pr.058) * Gear Ratio(Pr.053) 0~65530
159 Line Speed(3) 158 RPM(Pr.058) * Gear Ratio (Pr.053) / 100 0.00~655.30
159 RPM(Pr.058) * Gear Ratio(Pr.053) / 10 0.0~6553.0
200 Iv A/D Value Monitors A/D converted data of Iv.
201 AI1 A/D Value Monitors A/D converted data of AI1.
202 AI2 A/D Value Monitors A/D converted data of AI2.
203 AI3 A/D Value Monitors A/D converted data of AI3.
204 Iw A/D Value Monitors A/D converted data of Iw.
205 Idc A/D Value Monitors A/D converted data of Idc.
206 Vcap A/D Value Monitors A/D converted data of Vcap.
207 Temperature A/D Value Monitors A/D converted data of Temperature.
574 μm Display BCD (Low)
Actual position expressed in μm (BCD format)
575 μm Display BCD (High)
578 Position BCD (Low)
Actual position expressed in clocks (BCD format)
579 Position BCD (High)
580 Position Hex (Low)
Actual position expressed in clocks (HEX format)
581 Position Hex (High)
582 μm Display Hex (Low)
Actual position expressed in μm (HEX format)
583 μm Display Hex (High)

28
5.2.9 XY Pulse Command Input Parameters
Pr.nnn Parameter Name Description
130 XY Clock Type Select
Pr.130 XY Clock Type
0 Two phase input clocks and X4 rate
X+

Y+

Count
(Pr.137) 1 3 5 7 9 8 6
十六進制
2 4 6 8 A 9 7 5

1 CLOCK and DIRECTION signals

X signal: Clock Pulse
Y signal: Direction
X+

Y+

Count
(Pr.137) 1 2 2 1
2 UP-clock and DOWN-clock pulses
X signal: UP-Clock
Y signal: DOWN-closk
X+

Y+

Count
(Pr.137) 1 2 3 2 1
3 Two phase input clocks and X2 rate
X+

Y+

Count
(Pr.137) 1 2 3 4 5 4 3 2 1
Refer to section 1.2.2 for XY Pulse ipunt interface and signals description
131 XY Input Pin Status Monitors XY pulse input pins status.
132 XY Direction Change Change XY counter direction.
When DIx(139)(XY Direction Change) selected, DIx(139) determines XY counter
direction.
133 XY Multiply Rate 0 Use DIx(64)(XY Multiply) and DIx(65)(XY Division) to select Multiply Rate and
134 XY Division Rate 0 Division Rate, and input clock rate counts as following:
135 XY Multiply Rate 1 DIx(64) DIx(65) Clock Rate
136 XY Division Rate 1 OFF OFF Multiply Rate 0 / Division Rate 0
OFF ON Multiply Rate 0 / Division Rate 1
ON OFF Multiply Rate 1 / Division Rate 0
ON ON Multiply Rate 1 / Division Rate 1
Pr.134=0 and Pr.136=0 means Division Rate = 10000
137 XY Counter Value Monitors the content of pulses input to XY counter, expressed in Hex form.
Pr.137=XY-input* (XY-Multiply / XY-Divide) * XY-Direction
138 XY Sampling Period Pr.139 XY Rate is the total pulse counter per the period of Pr.138 XY Sampling Period
139 XY Rate

29
 DIx(64) Pcmd/Tracking Function Block Diagram
Pr.135
Pr.133

MULTIPLY
Pcmd from Master Actual Position cmd.

DIVIDE DIx(218)

Pr.134
JOG*PID AI1
Pr.136
*AI1
DIx(65) DIx(58)

DIx(219)
Analog AI1
JOG*AI1 DIx(168)

DIx(59)
PID output
DIx(46) DIx(47) JOG*PID

DIx(169)

JOG(Pcmd)

The following table lists the relative Digital Input function.

DIx Function Description
46 TRACK + JOG DIx(46), DIx(47), DIx(58), DIx(59), DIx(168), DIx(169),DIx(218) and
47 TRACK – JOG DIx(219) are used to assign the Set Speed under tracking mode, if the
58 TRACK + (AI1 * JOG) digital input terminal is ON, the Set Speed as following:
59 TRACK – (AI1 * JOG) DIx Set Speed
168 TRACK + (PID Output * JOG) 46 Tracking Speed + JOG Speed (Pr.019)
169 TRACK – (PID Output * JOG) 47 Tracking Speed – JOG Speed (Pr.019)
218 TRACK + JOG * AI1 * PID OUTPUT 58 Tracking Speed + AI1 Input * JOG Speed (Pr.019)
219 TRACK – JOG * AI1 * PID OUTPUT 59 Tracking Speed – AI1 Input * JOG Speed (Pr.019)
168 Tracking Speed + PID Output * JOG Speed (Pr.019)
169 Tracking Speed – PID Output * JOG Speed (Pr.019)
218 Tracking Speed plus (PID Output*AI1*JOG Speed)
219 Tracking Speed minus (PID Output*AI1*JOG Speed)
l Use these functions only under tracking mode.
l AI1 range can only select 0~5V or 0~10V.
l AI1input range = +100% ~ –100%
104 XY CLOCK INPUT ENABLE
DIx(104) DIx(105) XY Clock Input
105 /XY CLOCK INPUT ENABLE
0FF 0N Disable
ON OFF Enable

30
5.2.10 PID Function
PID Function Block
Set Selection (aa) Set Polarity (Bit0) Auto Gain Select (Bit6) PID Limit (Pr.248) Output Polarity (Bit3)

Integrator Clear DIx(167)

Pr.247 Integrator Hold (Bit5) ＋
AI-1 PID Set ×＋1
AI-2 Switch or
Set
×－1
AI-3
PID process
＋ Pgain or
Error Output ×＋1 PID Output
Σ I gain ＋ or
－ Dgain ×－1
FB Dtime
Pr.247
AI-1 PID FB ×＋1
Switch or FBgain
AI-2 －
×－1
AI-3

FB Selection (bb) FB Polarity (Bit1) PID Enable (Bit4) PID Range (Bit2)

Pr.nnn Parameter Name Description

240 PID Input Select This parameter composed by “aa” & “bb” separated by decimal point.
The aa value is used to select the PID Set signal source for PID block.
The bb value is used to select the PID FB signal source for PID block.
The equivalent source for selection value “aa” or “bb” is:
Pr.240 Description
0 Constant value defined by Pr.247 (0~100%)
1 Bipolar input from AI1
2 Bipolar input from AI2
3 Bipolar input from AI3
5 Motor RPM
6 Motor output Tcmd
10 Pr.139 XY Rate
11 Unipolar input from AI1
12 Unipolar input from AI2
13 Unipolar input from AI3
241 PID Default Configuration Pr.241=N, the value N is composed of 7 different bit switches. While Power ON or
after RESET, the 7 bit switches are used to configure the PID block.
N = 64*Bit6 + 32*Bit5 + 16*Bit4 + 8*Bit3 + 4*Bit2 + 2*Bit1 + 1*Bit0
If any of these switches requires random change, use DIx(160)~DIx(165) for
equivalent bits.
Bit n Name Function Equivalent DIx
=0, Set = (+1) * PID Set
Bit0 Set Polarity DIx(160)
=1, Set = (–1) * PID Set
=0, FB = (+1) * PID FB
Bit1 FB Polarity DIx(161)
=1, FB = (–1) * PID FB
=0, Output with Bipolar value
Bit2 PID Range DIx(162)
=1, Output with Unipolar value
=0, PIDOutput = (+1) * Output
Bit3 Output Polarity DIx(163)
=1, PID Output= (–1) * Output
=0, PID block disabled
Bit4 PID Enable DIx(164)
=1, PID block enabled
=0, PID Integrator normal
Bit5 PID Hold DIx(165)
=1, PID Integrator Hold
=0, Auto Gain disabled
Bit6 Auto Gain DIx(166)
=1, Auto Gain Enabled

242 PID Output Value Monitors Output value of PID block, expressed in Hex form.

31
 243 PID Pgain Error input
244 PID Igain
245 PID Dgain
249 PID Dtime
253 PID Auto Gain Select
time
PID output

Error*Igain*t
ΔError*Dgain

Error*Pgain
time
D-time
t
Pgain - Dgain Igain * 500
PID _ out = Error * + (DError * e Dtime ) * + Error * *t
256 256 65536
Note: the PID block is calculated every 2ms
Pr.253 used to select Auto Gain of PID block,
Pgain, Igain, Dgain = Set value * AutoGain-coefficient.
Pr.253 Auto Gain Source Range
0 No Auto Gain 100%
1 AI1 Input 0~100%
2 AI2 Input 0~100%
3 AI3 Input 0~100%
4 Speed / Maximum RPM (1/16)~100%
5 Average Speed / Maximum RPM
(1/16)~100%
(Speed is average every 0.25 second))
246 PID FBgain PID Feedback Gain
247 PID Constant Reference Constant value used as PID Set or PID FB reference.
248 PID Limit Maximum output limit of PID block.
250 PID Set Value Monitors Set value of PID block.
251 PID FB Value Monitors Feedback value of PID block
252 PID Error Value Monitors Error value of PID block
Other information:
l When Torque Limit select (Pr.333/383/433/483) = 5, PID Output becomes the torque limit source. (Refer to Pr.333)
l When Analog Output Source Select = 7, PID Output becomes the AOx Output value. (Refer to section 5.2.6)
l When Speed Source Select (Pr.040) = 40, PID Output becomes the Main Speed Source. (Refer to section 6.2.1)
l When DIx(167) = ON, clear PID integrator value.
l When DIx(168) is selected, Set Speed = Tracking Speed + PID Output * JOG Speed (Pr.019). (Refer to section 5.2.9)
l When DIx(169) is selected, Set Speed = Tracking Speed – PID Output * JOG Speed (Pr.019). (Refer to section 5.2.9)

32
5.2.11 Motor Parameter Groups
Pr.nnn
Parameter Name Description
Group#0 Group#1 Group#2 Group#3
300 350 400 450 Motor Type Select
Pr.300 Description
0 Induction motor V/F control
1 Induction motor Sensor-Less mode
2 Induction motor Servo mode
3 Brushless servo motor
301 351 401 451 ABC Status Monitors encoder status
302 352 402 452 Encoder PPR Pulse per revolution of encoder
303 353 403 453 A-Lead/Lag-B Determine encoder feedback direction
304 354 404 454 AB Filter Determine sampling period of encoder
305 355 405 455 AB Counter Monitors counter value of encoder (Hex form)
306 356 406 456 UVW Status Monitors Brushless servo motor UVW status
307 357 407 457 Motor Rated Voltage (Motor Rated Voltage / Line Voltage) * 100%
308 358 408 458 Motor Peak Voltage (Motor Peak Voltage / Line Voltage) * 100%
309 359 409 459 Boost Voltage Minimum voltage while output speed is low.
For induction motor V/F mode only.
310 360 410 460 Motor Rated RPM Rated speed of motor
311 361 411 461 Motor Rated Current (Motor Rated current / Drive Rated Current) * 100%
312 362 412 462 Motor Peak Current (Motor Peak Current / Motor Rated Current) * 100%
313 363 413 463 Field Current (Motor Field Current / Motor Rated current) * 100%
314 364 414 464 Pole Pole number of motor
315 365 415 465 Maximum RPM Maximum speed of motor (RPM)
316 366 416 466 Minimum RPM Minimum speed of motor (RPM)
317 367 417 467 Slip RPM Slip speed of induction motor (RPM)
318 368 418 468 Encoder PPR Check Recode PPR of motor, the value is 4*Encoder PPR
319 369 419 469 Reserve Reserved for special use, must set to 0 normally.
320 370 420 470 P gain (Current Loop) P gain constant for current loop
321 371 421 471 I gain (Current Loop) I gain constant for current loop
322 372 422 472 Reserve Reserved for special use, must set to 0 normally.
323 373 423 473 P gain (Speed Loop) P gain constant for speed loop
324 374 424 474 I gain (Speed Loop) I gain constant for speed loop
325 375 425 475 Reserve Reserved for special use, must set to 0 normally.
326 376 426 476 P gain (Position Loop) P gain constant for position loop
327~329 377~379 427~429 477~479 Reserve Rreserved for special use, must set to 0 normally.
330 380 430 480 Position/Speed Select
Setting Mode
0 Speed Control Mode
1 Position Control Mode
If there exists any DIx(106) or DIx(107) selected, then
Position/Speed control mode is selected by Digital
Input Terminal.
DIx Status Mode
DIx(106) ON or DIx(107) OFF Speed Mode
DIx(106) OFF or DIx(107) ON Position Mode
331 381 431 481 Pcmd/APTP Select
Setting Mode
0 Auto Point to Point (APTP)
1 Pulse Command control (Pcmd)
If there exists any DIx(126) or DIx(127) selected, then
Pcmd/APTP control mode is selected by Digital Input
Terminal.
DIx Status Mode
DIx(126) ON or DIx(127) OFF Pcmd Mode
DIx(126) OFF or DIx(127) ON APTP Mode
332 382 432 482 Absolute/Increment Setting Description
Select
0 Increment Position control for APTP
1 Absolute Position control for APTP

33
 333 383 433 483 Torque Limit Source Torque Limit Source Select = a.b, it is composed of
Select two selection of “a” and “b” in one parameter, if
DIx(108)(Torque Limit SW) is ON, then Torque Limit
Source = “b”, otherwise Torque Limit Source = “a”.
DIx(109) is complementary function of DIx(108)
“a” or “b” Torque Limit Source
0 No torque limit
1 AI1
2 AI2
3 AI3
4 Pr.067 (RAM)
5 PID Output
6 Pr.069 (EAROM)
7 Analog Input AI1 * AI2
334 384 434 484 Length Conversion If used micrometer as the unit of Destination
Location/Length, this parameter defines the number of
data to be converted micrometer into clocks. And
Pr.576/577 defines the conversion rate.
Setting Conversion
0 No conversion
1~16 Select total “n” data for conversion.
Example:
n=1, then DL16 convert to DL0
n=2, DL16àDL0, DL17àDL1
n=16, DL16àDL0, DL17àDL1,
DL18àDL2,.….,DL31àDL15
335 385 435 485 Length Compensation When power ON, the desired length is:
336 386 436 486 Compensation Polarity Length Compensation Desired
Compensation Polarity Length
0 0 or 1 DLn
1 0 DLn+DL1
1 1 DLn-DL1
After power ON, user can use DIx(147) and DIx(148)
to change the desired length.
DIx(147) DIx(148) Desired Length
OFF ON or OFF DLn
ON OFF DLn+DL1
ON ON DLn-DL1
337~339 387~389 437~439 487~489 Reserve Reserved for special use, and must set to 0 normally.
340 390 440 490 Resolver Shift Angle Defines the shift angle between motor and resolver.
341 391 441 491 Resolver Polarity Defines the polarity of Sine Cosine signal.
342 392 442 492 BL Motor Select Brushless Servo Motor type select, normal set to 0.
Please consult to our R&D department for details.
343 393 443 493 Direct Torque Control
Setting DI(208) Torque Control Mode
Select
0 OFF Stardard Torque Control Mode.
This mode only control
maximum torque, Torque Limit
Source select by
Pr.333/383/433/483
1 ON Direct Torque Control Mode.
This mode control both Torque
and Speed; torque limit source
determined by AI1; maximum
forward speed determined by
Pr.500; maximum reverse speed
determined by Pr.502.
345~349 395~399 435~439 495~499 Reserve Reserved for special use, and must set to 0 normally.

34
5.2.12 Auto Point-to-Point Control
APTP Trapezoidal Speed Profile Generator

Example timing cahrt of Standard APTP function Block

Speed +DL3 time

-DL1

DIx(119) Direction
DIx(120) Pt.Sel.Bit0
DIx(121) Pt.Sel.Bit1
(assume SelBit2~4 not used) Select Point3(+) Select Point1(-)
DIx(118) APTP trig.

DOx(124) Servo end

Pr.nnn Parameter Name Description

193 Home Direction
Pr.193 Home Search Direction
194 Home Speed and Acc/Dec 0 Forward
1 Reverse
2 DIx(119) OFF: Forward, DIx(119) ON: Reverse
Pr.194 Home Search Speed and Acc/Dec
0 Normal Speed and Main Acc/Dec
1 JOG Speed and JOG Acc/Dec
Home Search Process
DIx Description
128 l For absolute position control mode, must execute Home
(Home Start) Search process before execute APTP function.
129 l Pr.193 defines home search direction and Pr.194 defines
(Home Stop(1)) Home search speed and Acc/Dec.
170 l If DIx(129) is OFF and DIx(128) is triggered, the drive
(Home Stop(2)) will start Home Search process until DIx(129) is ON.
After Dix(129) ON, the drive start to search encoder
index, and automatically stop at the Index Offset
(Pr.568/569) position.
l If DI1(170) is OFF and DIx(128) is triggered, the drive
will start Home Search process until DI1(170) is ON.
After DI1(170) ON, the drive automatically stop at the
Index Offset (Pr.568/569) position from current position.
l The DOx(56) will ON immediately after start Home
Search (DIx(128) is triggered). When Home Search
complete, the DOx(56) will OFF automatically.
l DOx(57) is complement function of DOx(56).
l If DOx(128) ON, indicating Home Search already
performed. DOx(128) will OFF after drive RESET or
change to Speed Mode.
l DOx(129) is complement function of DOx(128).
NOTE:
1. Only DI1 input can select DI1(170) function.
2. Cannot select DIx(129) and DI1(170) simultaneously.
137 Under Absolute APTP mode, trigger DIx(137) will assign the
(Assign Home) current position as HOME position.
138 Under Absolute APTP mode, trigger DIx(138) will command
(Return Home) the motor return to HOME position.

35
500 DL0 (Low) l These parameters store 32 points data used in Auto Point-to-Point operation.
501 DL0 (High) l If select Incremental mode, these values mean the desired Destination Length.
502 DL1 (Low) l If select Absolute Mode, these values mean the desired Destination Location.
503 DL1 (High) l Each Destination Location/Length is composed by two parameters forming an
504 DL2 (Low) 8-digital value. Named as DL0、DL1、DL2………DL31。
505 DL2 (High) DL0 = Pr.501 * 10000 + Pr.500
﹕ ﹕ DL1 = Pr.503 * 10000 + Pr.502
﹕ ﹕ ﹕
﹕ ﹕ ﹕
558 DL29 (Low) ﹕
559 DL29 (High) DL30 = Pr.561 * 10000 + Pr.560
560 DL30 (Low) DL31 = Pr.563 * 10000 + Pr.562
561 DL30 (High) Auto Point-to-Point Process
562 DL31 (Low) DIx Description
563 DL31 (High) l After DLn (DIx(120)~DIx(124)) and its polarity
(DIx(119)) selected, the drive will execute APTP function
118 when DIx(118) is triggered.
(APTP Trigger) l DOx(126) APTP Busy, if DOx(126) is ON, indicating
APTP is processing.
l DOx(127) is complement function of DOx(126).
After DLn (DIx(120)~DIx(124)) selected,
l If DIX(119) OFF, the drive will execute APTP function
119
using +DLn value.
(Negative DLn)
l If DIX(119) OFF, the drive will execute APTP function
using -DLn value.
DIx(120)~DIx(124) are used for DLn selection.
l DIx(120): PTS0 Point Selection Bit0
l DIx(121): PTS1 Point Selection Bit1
120~124 l DIx(122): PTS2 Point Selection Bit2
(PTS0~PTS4) l DIx(123): PTS3 Point Selection Bit3
l DIx(124): PTS4 Point Selection Bit4
After PTS0~PTS4 are selected, then DLn is selected:
n = PTS4 * 16 + PTS3 * 8 + PTS2 * 4 + PTS1 * 2 + PTS0
In APTP mode, after APTP process is completed the
135
SERVO-END flag will set (DOx(124) will ON), and DIx(135)
(Clear Servo
is used to clear SERVO-END flag.
End Flag)
DOx(125) is complement function of DOx(124).
195 Travel Limit
Pr.195 Description
564 Forward Travel Limit 0 No software Travel Limit
(Low)
Enable Forward/Reverse software Travel Limit.
565 Forward Travel Limit 1 l Pr.564/565 defines Forward Travel Limit value.
(High) l Pr.566/567 defines Reverse Travel Limit value.
566 Reverse Travel Limit l If DOx(130) ON, indicating present position already exceeds Forward or
(Low) Reverse Travel Limit.
567 Reverse Travel Limit l If DOx(131) ON, indicating present position already exceeds Forward Travel
(High) Limit.
l If DOx(132) ON, indicating present position already exceeds Reverse Travel
Limit.
The function of DOx(130)~DOx(132) is enabled if Pr.195=1 and Home Search
already performed.
568 Index Offset (Low)
Pr.568/569 defines index offset of Home position.
569 Index Offset (High)
570 Position Error Limit While the drive is working under position mode (Tracking or APTP), with this
571 In Position Range function user can monitor the status of internal position control loop.
Pr.570 defines the warning clocks limitation.
Pr.571 defines the tolerance clocks of In-Position judgement.
Position Error = Position Desired – Position Feedback
DOx(52) will ON when│Position Error│≦ In Position Range
DOx(53) will ON when│Position Error│＞ In Position Range
DOx(54) will ON when│Position Error│≧ Position Error Limit
DOx(55) will ON when│Position Error│＜ Position Error Limit
576 μm Revolution (Low) Pr.576/577 defines the actual physical length when motor rotates on revolution.
577 μm Revolution (High) Usually defined in micro meter. Refer to Pr.334/384/434/483.
36
6. Selection of Speed Source
Speed Source Select Pr040 is used for speed input source selection. Through Pr.040 setting, the speed input sources may
come from Control Panel, Memory, Analog Input, Up/Down Counter, or the combination of the above sources.
Speed Source Select Pr.040=cc.dd is composed of two selection “cc” and “dd” in one parameter, if Speed command
SW DIx(88) or Speed & Control SW DIx(90) is ON then Speed Source =”dd”, otherwise Speed source=”cc”.
6.1 Speed Source Selection Table
Pr.040 Speed Source Reference
0 Set value in Pr.000 6.2.1
1 By AI1 Input
6.2.2
2 By AI2 Input
3 Set value from Panel 6.2.1
4 Both the output Speed and direction determined by AI1
6.2.2
5 Both the output Speed and direction determined by AI2
6 By internal Up/Down Counter
6.2.3
7 By internal Up/Down Counter, and will preload Up/Down counter from Pr.000 after RESET.
8 Set value from Panel, with PRELOAD from & AUTO WRITE to Pr.000 6.2.1
9 Both the output Speed and direction determined by AI1, with Minimum RPM
6.2.2
10 Both the output Speed and direction determined by AI2, with Minimum RPM
11 By internal Up/Down Counter 6.2.3
12 Speed Set = AI1* (1 ± (Pr.070*AI2)), with Minimum RPM 6.2.4
13 Speed Set = AI2 ± (Pr.015 * (Pr.070*AI1)), with Minimum RPM 6.2.4
17 By AI1 Input, with Minimum RPM
6.2.2
18 By AI2 Input, with Minimum RPM
19 By internal Up/Down Counter, with PRELOAD from & AUTO WRITE to Pr.000 6.2.3
20 By AI2 Input, but with Reverse Slope and Minimum RPM 6.2.2
21 Speed Set = Panel (or Computer) Set * (1 ± (Pr.070*AI2)), with Minimum RPM 6.2.4
22 Speed Set = Panel (or Computer) Set ± (Maximum RPM * (Pr.070*AI1)), with Minimum RPM 6.2.2
25 By AI3 Input 6.2.2
26 Both the output Speed and direction determined by AI3. 6.2.2
27 Both the output Speed and direction determined by AI3, with Minimum RPM 6.2.2
28 Speed Set = AI1 * (1 ± (Pr.070*AI3)), with Minimum RPM 6.2.4
29 Speed Set = AI3 ± (Maximum RPM * (Pr.070*AI1)), with Minimum RPM 6.2.4
30 By AI3 Input, with Minimum RPM 6.2.2
31 By AI3 Input, but with Reverse Slope and Minimum RPM
6.2.2
32 By AI1 Input, but with Reverse Slope and Minimum RPM
33 Speed Set = Panel (or Computer) Set * (1± (Pr0.70*AI1))
6.2.4
34 Speed Set = Panel (or Computer) Set * (1± (Pr.070*AI3))
35 Speed Set = Panel (or Computer) Set ± (Maximum RPM * (Pr.070*AI2)), with Minimum RPM
6.2.4
36 Speed Set = Panel (or Computer) Set ± (Maximum RPM * (Pr.070*AI3), with Minimum RPM
37 Forward by AI1, Reverse by AI2
6.2.2
38 Forward by AI2, Reverse by AI1
39 Set value in Pr.000, with Minimum RPM 6.2.1
40 By PID Output 6.2.1
41 Output Speed determined by XY pulse
6.2.3
42 Both the output Speed and direction determined by XY pulse
46 Set value in Pr.116 6.2.1
61 Both the output Speed and direction determined by AI1
62 Both the output Speed and direction determined by AI2. 6.2.2
63 Both the output Speed and direction determined by AI3.

37
6.2 Description of Speed Source
6.2.1 Speed Source from Memory & Panel
Pr.040 Speed Source Description
0 Pr.000 l The speed value stored in Pr.000 determines the output speed of the drive while running.
l The direction of the output phase sequence determined by control command (Pr.039).
3 Panel l If Pr.182=0, the set speed comes from Control Panel directly.
l If Pr.182=1, if communication option is used, the set speed comes from RS485
communication port.
l The direction of the output phase sequence determined by control command (Pr.039).
l While the desired output speed is lower than Minimum RPM (Pr.316/366/416/466), the
actual output speed will maintain at the Minimum RPM.
8 Panel This mode is similar to Pr.040=3, with only two differences:
l When power ON or after RESET, the data in Pr.000 will preload into internal set speed buffer
l When using Control Panel, after changing set speed, the value in set speed buffer will write
back into Pr.000 automatically.
39 Pr.000 l The speed value stored in Pr.000 determines the output speed of the drive while running.
l The direction of the output phase sequence determined by control command (Pr.039).
l While the desired output speed is lower than Minimum RPM (Pr.316/366/416/466), the
actual output speed will maintain at the Minimum RPM.
40 PID Output The PID Output determines the output speed of the drive while running. Refer to section 5.2.10
46 Pr.116 l The speed value stored in Pr.116 determines the output speed of the drive while running.
l The direction of the output phase sequence determined by control command (Pr.039).
l This parameter stored in RAM instead of EAROM. Therefore, it can be modify randomly
and quickly. Usually, it is used for computer control application.

6.2.2 Speed Source from Analog Input

Pr.040 Speed Source Description
1 AI1 Speed l The voltage (or current) signal fed into Analog
2 AI2 Input Terminal will be used to determine the
25 AI3 Max RPM output speed of the drive while running.
l The direction of the output phase sequence
determined by control command (Pr.039).
l If the input signal reaches maximum level, the
set speed is equal to Maximum RPM
(Pr.315/365/415/465)
l If the desired set speed is lower than minimum
Analog RPM (Pr.316/366/416/466), the drive will
Min RPM Input stop.
+5V、+10V、
±10V、20mA
4 AI1 l The voltage (or current) signal fed into Analog
5 AI2 Speed (Forward) Input terminal will be used to determine the
26 AI3 Max RPM output speed and the direction of the output
phase sequence of the drive.
l If the input signal reaches maximum level, the
set speed is equal to Maximum RPM
(Pr.315/365/415/465) in forward direction.
Analog Input
l If the input signal reaches minimum level, the
Min Min RPM
set speed is equal to Maximum RPM in reverse
Min RPM Max direction.
Center l If the input signal around center level, the drive
will stop.
Signal Max Center Min
+5V +5V +2.5V 0V
Max RPM +10V +10V +5V 0V
Speed (Reverse) ±10V +10V 0V -10V
20mA 20mA 10mA 0mA

38
9 AI1 l The voltage (or current) signal fed into Analog
10 AI2 Speed (Forward) Input terminal will be used to determine the output
27 AI3 Max RPM speed and the direction of the output phase
sequence of the drive.
l If the input signal reaches maximum level, the set
speed is equal to Maximum RPM
(Pr.315/365/415/465) in forward direction.
Min Min RPM Analog Input l If the input signal reaches minimum level, the set
speed is equal to Maximum RPM in reverse
Min RPM Max direction.
Center l If the input signal around center level, the drive
will run at Minimum RPM (Pr.316/366/416/466).
Signal Max Center Min
+5V +5V +2.5V 0V
Max RPM +10V +10V +5V 0V
Speed (Reverse) ±10V +10V 0V -10V
20mA 20mA 10mA 0mA
17 AI1 Speed l The voltage (or current) signal fed into
18 AI2 Analog Input Terminal will be used to
30 AI3 M ax R PM determine the output speed of the drive
while running.
l The direction of the output phase
sequence determined by control
command (Pr.039).
l If the input signal reaches maximum
level, the set speed is equal to Maximum
RPM (Pr.315/365/415/465)
M in R PM Analog l If the desired set speed is lower than
Input
minimum RPM (Pr.316/366/416/466),
+5V、 +10V、 the drive will run at Minimum RPM.
±10V、 20m A
20 AI2 S peed l The voltage (or current) signal fed into
31 AI3 Analog Input Terminal will be used to
32 AI1 M ax R P M determine the output speed of the drive
while running.
l The direction of the output phase
sequence determined by control
command (Pr.039).
l If the input signal reaches minimum
level, the set speed is equal to Maximum
RPM (Pr.315/365/415/465)
A nalog l If the input signal reaches maximum
M in RPM Input
level, the drive will run at Minimum
+5V 、 +10V 、 RPM (Pr.316/366/416/466).
±10V 、 20m A
37 AI1 & AI2 l If the motor run in FORWARD direction, it is same as Pr.040=17, use AI1 as input source.
l If the motor run in REVERSE direction, it is same as Pr.040=18, use AI2 as input source.
38 AI1 & AI2 l If the motor run in FORWARD direction, it is same as Pr.040=18, use AI2 as input source.
l If the motor run in REVERSE direction, it is same as Pr.040=17, use AI1 as input source.

39
 61 AI1 l The voltage (or current) signal fed into Analog
62 AI2 Speed (Forward) Input terminal will be used to determine the
63 AI3 output speed and the direction of the output phase
Max RPM
sequence of the drive.
l If the input signal reaches minimum level, the set
speed is equal to Maximum RPM
Center (Pr.315/365/415/465) in forward direction.
Max l If the input signal reaches maximum level, the set
Min RPM
speed is equal to Maximum RPM in reverse
Min Min RPM Analog Input direction.
l If the input signal around center level, the drive
will stop.
Signal Max Center Min
+5V +5V +2.5V 0V
Max RPM +10V +10V +5V 0V
Speed (Reverse) ±10V +10V 0V -10V
20mA 20mA 10mA 0mA

l Set Jumper to match the input signal type and range. (Refer to section 1.2.3)
l If necessary, use Pr.089/090/091/092/191/192 to modify the input range. (Refer to section 5.2.6)

6.2.3 Speed Source from XY Pulse Input

Pr.040 Speed Source Description
41 XY Pulse Input The XY Pulse frequency determines the output speed of the drive while running
The control command (Pr.039) determines direction of the output phase sequence.
RPM set = abs(Pr.139) * (Pr.135/Pr.136)
Note: Pr.138 defines XY pulse sampling period.
42 XYPulse Input The XY Pulse frequency determine the output speed and the direction of the output phase
sequence of the drive.
RPM set = (Pr.139) * (Pr.135/Pr.136)
Note: Pr.138 defines XY pulse sampling period.

40
6.2.4 Speed Source from Internal Up/Down Counter
Pr.040 Speed Source Description
6 Up/Down *2 *3
P r.0 0 0
7 Counter
11
19 D Ix (1 9 ) U P P relo ad
*1
D Ix (2 0 ) D O W N
In tern al
U p /D o w n S p e ed D esire
D Ix (1 6 ) L O A D
C o u n ter C o u n ter O u tp u t
D Ix (1 5 ) C L E A R

D Ix (1 7 ) H O L D

1. If Pr.040=6,7,11 or 19, the up/down counter is used to determined the output speed.
2. If Pr.040=7 or 19, the data in Pr.000 will preload into the Up/Down counter when Power ON
or Reset.
3. If Pr.040=19, after Up/Down execution, the content of Up/Down counter will write into
Pr.000 automatically.
The signals come from Digital Input (DIx) terminal describe as following:
DIx Function Description
If DIx(15) is triggered, the content of the internal Up/Down Counter will
15 Clear be set to the value of Minimum RPM (Pr.316/366/416/466), and drive
will ramp down according to the rate of Main Deceleration time (Pr.002)
If DIx(16) is triggered, the content of the internal Up/Down Counter will
16 Load be set to the value of Maximum RPM (Pr.315/365/415/465), and drive
will ramp up according to the rate of Main Acceleration time (Pr.001)
If DIx(17) is triggered, the value of present output speed will be loaded
17 Hold
into the internal Up/Down Counter.
If DIx(19) is ON, the content of the internal Up/Down Counter will
19 Up
increase according to the rate of Main Acceleration Time (Pr.001).
If DIx(20) is ON, the content of the internal Up/Down Counter will
20 Down
decrease according to the rate of Main Deceleration Time (Pr.002).
Speed

M ax R PM

M in R P M

LO A D

H O LD

CLEA R

UP

DOW N

RUN

41
6.2.5 Set Speed from Two Speed Sources Combination
Set Speed Description
Master Speed * (100% ± Pr.040 Master Speed Source Proportional Rate Source
(Pr.070 * Proportional Rate))
12 AI1 AI2
28 AI1 AI3
33 Control Panel or RS485 Port AI1
21 Control Panel or RS485 Port AI2
34 Control Panel or RS485 Port AI3
l Pr.070 (Analog Input Gain) defines the gain of Proportional Rate when set speed
determine by the combination of two speed sources.
l If the signal level of proportional rate is maximum, the modification rate is
(100%+Pr.070).
l If the signal level of proportional rate is minimum, the modification rate is
(100%-Pr.070).
l If the desired set speed is lower than minimum RPM (Pr.316/366/416/466), the drive
will run at Minimum RPM.
Typical application is as follows:
Master Speed
To Other Drive

Rate 3 Rate 2 Rate 1

Drive 1 Drive 2 Drive 3

Master Speed ± (Max RPM * Pr.040 Master Speed Source Auxiliary Input
(Pr.070 * Auxiliary Input))
13 AI2 AI1
29 AI3 AI1
22 Control Panel or RS485 Port AI1
35 Control Panel or RS485 Port AI2
36 Control Panel or RS485 Port AI3
4

l Pr.070 (Analog Input Gain) defines the gain of Auxiliary Input when set speed
determine by the combination of two speed sources.
l If the signal level of Auxiliary Input is maximum, the modification quantity is
+(Maximum RPM * Pr.70).
l If the signal level of Auxiliary Input is minimum, the modification quantity is
-(Maximum RPM * Pr.70).
l If the desired set speed is lower than minimum RPM (Pr.316/366/416/466), the drive
will run at Minimum RPM.
Typical application is as follows:

M1 M2

Position
D rive 1 D etector D rive 2

A uxiliary Input

M aster Speed Set To O ther D rive

inverters

42
7. Selection of Digital Input Function
7.1 Digital Input Function Related Parameters
Pr.nnn Parameter Name Description
140 DI0 Select l The configuration of Digital Input refer to section 1.2.1
141 DI1 Select l All Digital Input terminals are scanned every 2.0ms.
142 DI2 Select l Each Digital Input terminal can be configured individually by corresponding
143 DI3 Select DIx Select parameters.
144 DI4 Select l DI0 do not connect to the user control terminal, and only connected to DO0
145 DI5 Select internally.
146 DI6 Select l DI11~DI14 do not connect to the user control terminal, and can only controlled
147 DI7 Select by Modbus communication.
148 DI8 Select
149 DI9 Select
150 DI10 Select
151 DI11 Select
152 DI12 Select
153 DI13 Select
154 DI14 Select

7.2 Selection Table of Digital Input Function

DIx Function Comment Reference
0 NULL Null function
1 EMS Emergency Stop 7.3.1
2 SPD3 SPD3 Speed Set
3 SPD2 SPD2 Speed Set
5.2.4
4 SPD1 SPD1 Speed Set
5 JOG JOG Speed Set
6 OH Over Heat Alarm 7.3.2
7 TMIA(1) Timer(1) Input (OFF-Delay Type) 7.3.3
9 FJR Forward JOG Run
7.3.1
10 RJR Reverse JOG Run
11 TMIB(1) Timer(1) Input (ON-Delay Type) 7.3.3
15 U/D CLEAR Set Up/Down Counter to Minimum RPM
16 U/D LOAD Set Up/Down Counter to Maximum RPM
17 U/D HOLD Hold Output Speed to Up/Down Counter 6.2.4
19 U/D UP Increase Up/Down Counter
20 U/D DOWN Decrease Up/Down Counter
21 ALARM CLEAR Clear Alarm when Alarm Occur 7.3.1
22 SET1(FF1) SET Input of Flip/Flop-1
23 CLR1(FF1) CLEAR Input of Flip/Flop-1
24 SET2(FF2) SET Input of Flip/Flop-2
7.3.4
25 CLR2(FF2) CLEAR Input of Flip/Flop-2
26 SET(FF1&FF2) SET Input to both Flip/Flop-1 and Flip/Flop-2
27 CLR(FF1&FF2) CLEAR Input to both Flip/Flop-1 and Flip/Flop-2
28 COUNTER INPUT Clock Input of Timer/Counter Block
7.3.3
29 COUNTER CLEAR Clear Input of Timer/Counter Block
30 /OH Complement of Over Heat 7.3.2
36 TMIC(1) Timer(1) Input (ON/OFF Type) 7.3.3
46 TRACK + JOG Tracking Speed plus JOG Speed
5.2.9
47 TRACK – JOG Tracking Speed minus JOG Speed
48 SPEED HOLD Hold Output Speed 7.3.1
58 TRACK + (AI1 * JOG) Tracking Speed plus (AI1*JOG Speed)
59 TRACK – (AI1 * JOG) Tracking Speed minus (AI1*JOG Speed)
64 XY MULTIPLY Select Multiply Rate of XY Input Clock 5.2.9
65 XY DIVISION Select Division Rate of XY Input Clock (Pr.133~136)
73 RUN FUNCTION Select RUN Function
5.2.5 (Pr.039)
74 REV FUNCTION Select REV Function
76 FORWARD INHIBIT Forward run inhibit
7.3.1
77 REVERSE INHIBIT Reverse run inhibit
43
DIx Function Comment Reference
80 SPEED SW 1
81 SPEED SW 2
16 Step Speed Select 5.2.4
82 SPEED SW 3
83 SPEED SW 4
84 JOG ACC/DEC TIME
85 SPD1 ACC/DEC TIME
Acceleration/Deceleration Time Select 5.2.4
86 SPD2 ACC/DEC TIME
87 SPD3 ACC/DEC TIME
88 SPEED COMMAND SW Speed Command Select Switch Sec. 6
89 CONTROL COMMAND SW Control Command Select Switch 5.2.5 (Pr.039)
90 SPEED & CONTROL SW Speed and Control Command Select Switch 5.2.5, Sec.6
91 /TMIA(1) Complement of Timer(1) Input (OFF-Delay Type)
92 /TMIB(1) Complement of Timer(1) Input (ON-Delay Type)
93 /TMIC(1) Complement of Timer(1) Input (ON/OFF Type)
94 TMIA(2) Timer(2) Input (OFF-Delay Type)
95 TMIB(2) Timer(2) Input (ON-Delay Type) 7.3.3
96 TMIC(2) Timer(2) Input (ON/OFF Type)
97 /TMIA(2) Complement of Timer(2) Input (OFF-Delay Type)
98 /TMIB(2) Complement of Timer(2) Input (ON-Delay Type)
99 /TMIC(2) Complement of Timer(2) Input (ON/OFF Type)
100 DRIVE ENABLE & RUN Enable Drive and Assert RUN Command
7.3.1
101 /(DRIVE ENABLE & RUN) Complement of DIx(100)
102 DRIVE ENABLE Enable Drive to Standby State
7.3.1
103 /(DRIVE ENABLE) Complement of DIx(102)
104 XY CLOCK INPUT ENABLE Enable XY Clock input
5.2.9
105 /XY CLOCK INPUT ENABLE Complement of DIx(104)
106 POSITION/SPEED MODE Change between Position and Speed mode
5.2.11 (Pr.330)
107 /(POSITION/SPEED MODE) Complement of DIx(106)
108 TORQUE LIMIT SW Select Torque Limit Source
5.2.11 (Pr.333)
109 /(TORQUE LIMIT SW) Complement of DIx(108)
114 MSB0
Motor Parameter Group Select 5.2.5 (Pr.188)
115 MSB1
118 APTP TRIGGER Trigger start Auto Point-to-Point Function 5.2.12
119 NEGATIVE DLn VALUE Use Negative DLn for ATPT Position 5.2.12
120 PTS0 Point Select Bit0
121 PTS1 Point Select Bit1
122 PTS2 Point Select Bit2 5.2.12
123 PTS3 Point Select Bit3
124 PTS4 Point Select Bit4
126 TRACK/ATPT SW Change between TRACK and APTP mode
5.2.11 (Pr.331)
127 /(TRACK/ATPT SW) Complement of DIx(126)
128 HOME START Start Home Search Process
5.2.12
129 HOME STOP (1) Stop Home Search Process Type 1
133 CHANGE FF1 Change Flip/Flop-1 status
7.3.4
134 CHANGE FF2 Change Flip/Flop-2 status
135 CLEAR SERVO END FLAG Clear SERVO END Flag in APTP mode 5.2.12
137 ASSIGN HOME Assign Home Position 5.2.12
138 RETURN HOME Command Motor return to Home Position 5.2.12
139 XY DIRECTION CHANGE XY Pulse input direction selection 5.2.9 (Pr.132)
140 FWD TRAVEL LIMIT Forward Travel Limit Switch
7.3.2
141 /(FWD TRAVEL LIMIT) Complement of Forward Travel Limit Switch
142 REV TRAVEL LIMIT Reverse Travel Limit Switch
7.3.2
143 /(REV TRAVEL LIMIT) Complement of Reverse Travel Limit Switch
147 ENABLE DL1 COMPENSATION Desired Length=DLn plus (or minus) DL1
5.2.11 (Pr.335)
148 SELECT DL1 POLARITY Determine Plus or Minus DL1
149 LATCH EMS Emergency Stop and Latched until Drive Reset 7.3.1
155 MARK LENGTH Select Mark Length 11.1.1

44
 DIx Function Comment Reference
160 PID SET POLARITY BIT Select PID Set Polarity
161 PID FB POLARITY BIT Select PID FB Polarity
162 PID RANGE BIT Select PID Range
163 PID OUTPUT POLARITY BIT Select PID Output Polarity
5.2.10
164 PID ENABLE BIT Enable PID Function
165 PID HOLD BIT Select PID Hold
166 PID AUTO GAIN ENABLE BIT Enable PID Auto Gain
167 PID CLEAR Clear PID integrator
168 TRACK + (PID OUTPUT * JOG) Tracking Speed plus (PID Output * JOG Speed)
5.2.9
169 TRACK – (PID OUTPUT * JOG) Tracking Speed minus (PID Output * JOG Speed)
170 HOME STOP (2) Stop Home Search Process Type 2 5.2.12
180 MARK INPUT Mark signal input
11.1
181 MARK INPUT (S-CURVE) Marksignal input (S-CURVE)
208 TORQUE CONTROL MODEL Torque control model select 5.2.11 (Pr.343)
209 JOG+ UNDER POSITION MODE Forward JOG run under position mode
7.3.1
210 JOG- UNDER POSITION MODE Reverse JOG run under position mode
218 TRACK + JOG * AI1 * PID OUTPUT Tracking Speed plus (PID Output*AI1*JOG Speed)
5.2.9
219 TRACK - JOG * AI1 * PID OUTPUT Tracking Speed minus (PID Output*AI1*JOG Speed)
249 RAMP DOWN EMS Ramp Down Emergency Stop 7.3.1
7.3 Description of Digital Input function
7.3.1 Control Function
DIx Function Description
1 EMS While drive running, if the DIx(1) is ON, then drive will stop the motor to ZERO
Speed immediately. If DIx(1) OFF, the drive will run at original Set Speed.
9 FJR When DIx(9) is ON, the drive execute Forward-Jog-Run without RUN command.
10 RJR When DIx(10) is ON, the drive execute Reverse-Jog-Run without RUN command.
21 ALARM CLEAR If DIx(21) is ON, will RESET the drive only when ALARM had occurred.
Note: the RST terminal is used to RESET the drive no matter ALARM
occurred or not.
48 SPEED HOLD When DIx(48) is ON, the drive will stop ramp up or ramp down, and hold on
present running speed. If DIx(48) change to OFF, the drive will resume ramp up or
ramp down.
76 FORWARD INHIBIT If DIx(76) ON, forward run is inhibited.
77 REVERSE INHIBIT If DIx(77) ON, reverse run is inhibited.
100 DRIVE ENABLE & RUN If DIx(100) is ON, enabled the drive and assert RUN command.
101 /(DRIVE ENABLE & RUN) DIx(101) is complement input of DIx(100).
102 DRIVE ENABLE If DIx(102) is ON, enabled the drive. RUN command is separately controlled.
103 /(DRIVE ENABLE) DIx(103) is complement input of DIx(102).
149 LATCH EMS While drive running, if the DIx(149) triggered, then drive will stop the motor to
ZERO Speed until the drive RESET or Power OFF.
209 JOG+ UNDER POSITION Under position mode,
MODE l If DIx(209) is ON, change operation mode to speed mode, and execute
210 JOG- UNDER POSITION Forward-Jog-Run.
MODE l If DIx(210) is ON, change operation mode to speed mode, and execute
Reverse-Jog-Run.
l When DIx(209) and DIx(210) resume to OFF, operation mode changes to
Position mode automatically.
l After execute this function, original position will be cleared.
l Do not select DIx(106) or DIx(107), if DIx(209) or DIx(210) is selected.
249 RAMP DOWN EMS l While drive running, if the DIx(249) is triggered, then drive will Ramp
Down to ZERO Speed immediately, and DOx(92) will ON immediately after
speed down to ZERO.
l Pr.029 defines the Deceleration time.
l Execute RESET for recovery from Ramp Down EMS.

45
7.3.2 Protection Function
DIx Function Description
6 OH If DIx(6) ON or DIx(30) OFF, the drive will disable the output transistors, and
30 /OH show OH alarm message on control panel.
140 FWD TRAVEL LIMIT Under Absolute APTP mode, DIx(140) can connect to Forward Travel Limit
141 /(FWD TRAVEL LIMIT) Switch, if DIx(140) is ON, then the motor will not rotate any further toward
FORWARD direction.
DIx(141) is complement input of DIx(140).
142 REV TRAVEL LIMIT Under Absolute APTP mode, DIx(142) can connect to Reverse Travel Limit
143 /(REV TRAVEL LIMIT) Switch, if DIx(142) is ON, then the motor will not rotate any further toward
REVERSE direction.
DIx(143) is complement input of DIx(142).

7.3.3 Timer & Counter Function

DIx Function Description
7 TMIA(1) The drive built in two general purpose TIMERs. For example of Timer(1):
91 /TMIA(1) l Digital input DIx assigned to TMIA(1) function DIx(7), it serves as input of the
94 TMIA(2) OFF-DELAY timer.
97 /TMIA(2) l To assign a digital output DOx, which select TMOA(1) function DOx(14) to serve
as output of this timer.
l To define the timer time in Pr.071.
When the timer input TMIA(1) DIx(7) is ON, the timer output TMOA(1) DOx(14) will
be ON immediately. If the timer input TMIA(1) DIx(7) become OFF, the timer will
start counting time. After waiting the specified time period of Pr.071 then TMOA
DOx(14) become OFF.
l DIx(91) /TMIA(1) is complement input of DIx(7) TMIA(1).
l DOx(40) /TMOA(1) is complement output of DOx(14) TMOA(1).
TMIA(1)
DIx(7) The function of Timer(2) is same as Timer(1)
or l Pr.072 defines the timer time for Timer(2).
Pr.
/TMIA(1) l DIx(94) TMIA(2) is the input of Timer(2).
DIx(91)
71 l DIx(97) /TMIA(2) is complement input of
DIx(94) TMIA(2).
TMOA(1) l DOx(94) TMOA(2) is the output of
DOx(14)
Pr.071 Timer(2).
l DOx(97) /TMOA(2) is complement output
/TMOA(1) of DOx(94) TMOA(2).
DOx(40)
11 TMIB(1) The drive built in two general purpose TIMERs. For example of Timer(1):
92 /TMIB(1) l Digital input DIx assigned to TMIB(1) function DIx(11), it serves as input of the
95 TMIB(2) ON-DELAY timer.
98 /TMIB(2) l To assign a digital output DOx, which select TMOB(1) function DOx(20) to serve
as output of this timer.
l To define the timer time in Pr.071.
When the timer input TMIB(1) DIx(11) is OFF, the timer output TMOB(1) DOx(20)
will be OFF too. Until the timer input TMIB(1) DIx(20) is ON and continue ON for a
specified time period of Pr.071 then TMOB DOx(14) become ON.
l DIx(92) /TMIB(1) is complement input of DIx(11) TMIB(1).
l DOx(41) /TMOB(1) is complement output of DOx(20) TMOB(1).
TMIB(1) The function of Timer(2) is same as Timer(1)
DIx(11)
l Pr.072 defines the timer time for
or Timer(2).
/TMIB(1) l DIx(95) TMIB(2) is the input of
DIx(92) Timer(2).
l DIx(98) /TMIB(2) is complement input
Pr.071 of DIx(95) TMIB(2).
TMOB(1)
DOx(20) l DOx(95) TMOB(2) is the output of
Timer(2).
/TMOB(1) l DOx(98) /TMOB(2) is complement
DOx(41) output of DOx(95) TMOB(2).

46
28 COUNTER INPUT Pr.108 (Counter Value) Monitors the value of clock input to counter.
29 COUNTER CLEAR Pr.109 (Counter Set) defines maximum clock input value of counter.
l Digital input DIx assigned to Counter Input DIx(28), it serves as input of Counter.
If DIx(28) triggered, the content of Pr.108 (Counter Value) will increase of 1.
l Digital input DIx assigned to Counter Input DIx(29), it serves as clear of Counter.
If DIx(29) triggered, the content of Pr.108 (Counter Value) will clear to zero.
l To assign a digital output DOx, which select Counter Over function DOx(140) to
serve as output of this counter, if Pr108≧Pr.109, then DOx(140) become ON.
l The minimum width of trigger signal is 5ms.。
l DOx(141) is complement output of DOx(140).
36 TMIC(1) The drive built in two general purpose TIMERs. For example of Timer(1):
93 /TMIC(1) l Digital input DIx assigned to TMIC(1) function DIx(36), it serves as input of the
96 TMIC(2) ON/OFF timer.
99 /TMIC(2) l To assign a digital output DOx, which select TMOC(1) function DOx(42) to serve
as output of this timer.
l To define the period of time for one ON/OFF cycle in Pr.071.
When the timer input TMIC(1) DIx(36) is OFF, the timer output TMOC(1) DOx(42) is
always under ON state. If the TMIC(1) DIx(36) is ON, then the TMOC DOx(42) will
start the stable ON/OFF cycle.
l DIx(93) /TMIC(1) is complement input of DIx(36) TMIC(1).
l DOx(43) /TMOC(1) is complement output of DOx(42) TMOC(1).
The function of Timer(2) is same
TMIC(1) as Timer(1)
DIx(36)
l Pr.072 defines the timer time
or for Timer(2).
/TMIC(1) l DIx(96) TMIC(2) is the input
DIx(93)
of Timer(2).
l DIx(99) /TMIC(2) is
TMOC(1) complement input of DIx(96)
DOx(42) TMIC(2).
l DOx(96) TMOC(2) is the
/TMOC(1) output of Timer(2).
DOx(43) l DOx(99) /TMOC(2) is
complement output of
Pr.071 Pr.071
DOx(96) TMOC(2).

47
7.3.4 Flip/Flop Function
DIx Function Description
22 SET1(FF1) DIx(26)
23 CLR1(FF1) Set A DOx(32) The drive built in two general purpose Flip/Flops .
DIx(22) Q
24 SET2(FF2) Set B Each Flip/Flop block has two SET inputs, two
25 CLR2(FF2) DIx(27) FF1 CLEAR inputs and two complementary outputs
Clr A _ DOx(33)
26 SET(FF1&FF2) DIx(23) for free selection.
Clr B Q
27 CLR(FF1&FF2) l If triggered Set A or Set B, will cause Q ON
DIx(26) and /Q OFF.
Set A DOx(34)
DIx(24) Q l If triggered Clr A or Clr B, will cause Q
Set B
OFF and /Q ON.
DIx(27) FF2
Clr A _ DOx(35)
DIx(25) Q
Clr B
Application example: Use DI1, DI2, DO1 and DO2 as LATCH RELAY.

Pr.141=22 Pr.161=4
START
Driver Pr.142=23 Pr.162=32
DI1 Pr.143=23
STOP
DI2
DI3
ALARM Start
DO1
DO2 Stop or Alarm
RUN
RUN
Run
DCOM

133 CHANGE FF1 If DIx(133) is triggered, the status of Flip/Flop-1 (DOx(32) and DOx(33)) will be changed.
134 CHANGE FF2 If DIx(134) is triggered, the status of Flip/Flop-1 (DOx(34) and DOx(35)) will be changed.

48
8. Selection of Digital Output Function
8.1 Digital Output Function Related Parameters
Pr.nnn Function Description
161 DO0 Select l The configuration of Digital Output refer to section 1.2.2
161 DO1 Select l Each Digital Output terminal can be configured individually by corresponding DOx
162 DO2 Select Select parameters.
163 DO3 Select l DO0 is connected to the Digital Input DI0 internally.
164 DO4 Select l RY1 and RY2 pair terminals are NORMAL OPEN (1a) contacts of the output RELAY,
165 DO5 Select and named DO3.
166 DO6 Select Note: All of the Digital Outputs will go OFF for a short period when power ON or RESET.

8.2 Selection Table of Digital Output Function

DOx Function Comment Reference
0 OFF Always OFF 8.3.2
1 /(ENABLE) Drive Not Enable 8.3.4
2 SPE Speed Equal
8.3.1
3 SPNE Speed Not Equal
4 ALM Alarm
8.3.4
5 NALM No Alarm
7 ENABLE Drive Enabled 8.3.4
8 SPO Speed Over
8.3.1
9 SPNO Speed Not Over
10 SPA Speed Arrive
8.3.1
11 SPNA Speed Not Arrive
13 Irms > Pr.048 Irms > Pr.048 8.3.4
14 TMOA(1) Timer(1) Output (OFF-Delay Type) 7.3.3 DIx(7)
15 SPZ Zero Speed
8.3.1
16 SPNZ Speed Not Zero
20 TMOB(1) Timer(1) Output (ON-Delay Type) 7.3.3 DIx(11)
32 Q1(FF1) Output of Flip/Flop-1
33 /Q1(FF1) Complement Output of Flip/Flop-1
7.3.4
34 Q2(FF2) Output of Flip/Flop-2
35 /Q2(FF2) Complement Output of Flip/Flop-2
38 ON Always ON 8.3.2
39 DO1 CLOCK Clock output (for DO1 only) 8.3.3
40 /TMOA(1) Complement of Timer(1) Output (OFF-Delay Type) 7.3.3 DIx(7)
41 /TMOB(1) Complement of Timer(1) Output (ON-Delay Type) 7.3.3 DIx(11)
42 TMOC(1) Timer(1) Output (ON/OFF Type)
7.3.3 DIx(36)
43 /TMOC(1) Complement of Timer(1) Output (ON/OFF Type)
52 IN POSITION Position Error <= In Position Range
53 /(IN POSITION) Position Error > In Position Range
5.2.12 (Pr.570)
54 ERROR OVER Position Error > Error Limit
55 /(ERROR OVER) Position Error <= Error Limit
56 SEARCHING HOME Drive is Searching Home Position
5.2.12 (DIx(128))
57 /(SEARCHING HOME) Drive is Not Searching Home position
70 (ENABLE) & (AI1>Pr.561) Drive Enabled and AI1 Input Level > Pr.561
71 (ENABLE) & (AI1<Pr.561) Drive Enabled and AI1 Input Level < Pr.561
72 (ENABLE) & (AI2>Pr.562) Drive Enabled and AI2 Input Level > Pr.562
8.3.4
73 (ENABLE) & (AI2<Pr.562) Drive is Enabled and AI2 Input Level < Pr.562
74 (ENABLE) & (AI3>Pr.563) Drive is Enabled and AI3 Input Level > Pr.563
75 (ENABLE) & (AI3<Pr.563) Drive is Enabled and AI3 Input Level < Pr.563
78 OL WARNING Over Load Level > 50%
8.3.4
79 /(OL WARNING) Over Load Level < 50%
80 AI1>Pr.561 AI1 Input Level > Pr.561
81 AI1<Pr.561 AI1 Input Level < Pr.561
82 AI2>Pr.562 AI2 Input Level > Pr.562
8.3.4
83 AI2<Pr.562 AI2 Input Level < Pr.562
84 AI3>Pr.563 AI3 Input Level > Pr.563
85 AI3<Pr.563 AI3 Input Level < Pr.563

49
 DOx Function Comment Reference
86 ACCELERATING Under Acceleration status for Speed mode 8.3.4
87 DECELERATING Under Deceleration status for Speed mode 8.3.4
92 SHUTDOWN Ramp Down EMS 7.3.1 DIx(249)
94 TMOA(2) Timer(2) Output (OFF-Delay Type) 7.3.3 DIx(7)
95 TMOB(2) Timer(2) Output (ON-Delay Type) 7.3.3 DIx(11)
96 TMOC(2) Timer(2) Output (ON/OFF Type) 7.3.3 DIx(36)
97 /TMOA(2) Complement of Timer(2) Output (OFF-Delay Type) 7.3.3 DIx(7)
98 /TMOB(2) Complement of Timer(2) Output (ON-Delay Type) 7.3.3 DIx(11)
99 /TMOC(2) Complement of Timer(2) Output (ON/OFF Type) 7.3.3 DIx(36)
123 ENCODER ZERO Pass Through Encoder Zero Point 8.3.3
124 SERVO END APTP Process is Completed
5.2.12 DIx(135)
125 /SERVO END Complement Output of DOx(124)
126 APTP BUSY APTP is Processing
5.2.12 (DIx(118))
127 /APTP BUSY Complement Output of DOx(126)
128 HOME EXIST Home Search is Completed
5.2.12 (DIx(128))
129 /HOME EXIST Complement Output of DOx(128)
130 TRAVEL LIMIT Position Exceeds Limit in Both Direction
131 FWD TRAVEL LIMIT Position Exceeds Forward Direction 5.2.12 (Pr.565)
132 REV TRAVEL LIMIT Position Exceeds Reverse Direction
140 COUNT OVER Counter Input Exceeds Counter Set Value
7.3.3 DIx(28)
141 /COUNT OVER Complement Output of DOx(140)
150 >WINDOW2 Feed Length > Lower Limit of Window2
151 <WINDOW2 Feed Length < Upper Limit of Window2 11.1.3
152 IN WINDOW2 Feed Length in the position of Window2
180 MARK LOSS MARK signal loss 11.1
181 WINDOW In Position of WINDOW 11.1.2
200 DI0 STSTUS Monitor DI0 input status
201 DI1 STSTUS Monitor DI1 input status
202 DI2 STSTUS Monitor DI2 input status
203 DI3 STSTUS Monitor DI3 input status 8.3.4
204 DI4 STSTUS Monitor DI4 input status
205 DI5 STSTUS Monitor DI5 input status
206 DI6 STSTUS Monitor DI6 input status
8.3 Description of Digital Output Function
8.3.1 Speed Monitor Function
DOx Function Description
2 SPE Pr.049 (Detect RPM) defines the threshold level for Speed Detector module.
3 SPNE Pr.050 (Detect Tolerance) defines the allowable tolerance for Speed Detector module.
8 SPO l If abs(Output Speed – Pr.049) < Pr.050, DOx(2) will ON.
9 SPNO l DOx(3) is complement output of DOx(2).
10 SPA l If Output Speed > Pr.049, DOx(8) will ON.
11 SPNA l DOx(9) is complement output of DOx(8).
15 SPZ l If (Set Speed - Output Speed) < Pr.050, DOx(10) will ON.
16 SPNZ l DOx(11) is complement output of DOx(10).
l If Output Speed < Pr.050, DOx(15) will ON.
l DOx(16) is complement output of DOx(15).
O u tpu t S peed
S e t S p e ed P r.0 50
P r.0 50
P r.0 49 P r.0 50
P r.0 50 tim e
D O x(2)S P E
tim e
D O x(8)S P O
tim e
D O x(15 )S P Z
tim e
D O x(10 )S PA
tim e
50
8.3.2 ON/OFF Control Function
DOx Function Description
0 OFF When Digital Output DOx assigned to ON function DOx(0), the output status of DOx
38 ON will always OFF.
When Digital Output DOx assigned to OFF function DOx(38), the output status of DOx
will always ON.
This function is useful to control these Digital Outputs for other peripheral, independent
to the drive operation.
8.3.3 Pulse Output Function
DOx Function Description
39 DO1 CLOCK Pr.077 (DO1 Pulse Output Ratio) defines DO1 Pulse Output ratio, it is used for DO1
Clock frequency calculation.
If Digital Output DOx assigned to DO1 CLOCK function DOx(39), it serves as CLOCK
Generator.
Output Frequency = (Motor Speed (RPM)/60)*(POLE)/2)*(Pr.077)
l This function for DO1 only.
l Maximum output frequency is 1500Hz.
123 ENCODER ZERO If Digital Output DOx assigned to ENCODER ZERO function DOx(123), when the
motor rotates pass through Encoder Index, DOx(123) will be ON for 4ms, then change to
OFF state automatically.
8.3.4 Running Status Monitor Function
DOx Function Description
1 /(ENABLE) The output status of DOx(7) will be ON when the IGBT is triggered (drive is
7 ENABLE enabled), otherwise DOx(7) is OFF.
DOx(1) is complement output of DOx(7).
4 ALM The output status of DOx(4) is normally OFF when the drive detects No Alarm.
5 NALM If Alarm occurs, the output DOx(4) will ON immediately.
DOx(5) is complement output of DOx(4).
13 Irms > Pr.048 Pr.048 (Detect Irms) defines the threshold level for Irms detector module.
The ourput status of DOx(13) will be ON when Irms(%) > Pr.048.
70 (ENABLE) & (AI1>Pr.561) If Digital Output DOx select DOx(70)~DOx(75) or DOx(80)~DOx(85), DOx are
71 (ENABLE) & (AI1<Pr.561) used to detect the input level of AIx respectively. If the comparison result is meet
72 (ENABLE) & (AI2>Pr.562) the condition of follows table, the output DOx will be ON, otherwise DOx is OFF.
73 (ENABLE) & (AI2<Pr.562) DOx Condition
74 (ENABLE) & (AI3>Pr.563) 70 AI1 > Pr.561 and drive is enabled
75 (ENABLE) & (AI3<Pr.563) 71 AI1 < Pr.561 and drive is enabled
80 AI1 > Pr.561 72 AI2 > Pr.562 and drive is enabled
81 AI1 < Pr.561 73 AI2 < Pr.562 and drive is enabled
82 AI2 > Pr.562 74 AI3 > Pr.563 and drive is enabled
83 AI2 < Pr.562 75 AI3 < Pr.563 and drive is enabled
84 AI3 > Pr.563 80 AI1 > Pr.561
85 AI3 < Pr.563 81 AI1 < Pr.561
82 AI2 > Pr.562
83 AI2 < Pr.562
84 AI3 > Pr.563
85 AI3 < Pr.563
l AI1 input level can be monitored by Pr.201.
l AI2 input level can be monitored by Pr.202.
l AI3 input level can be monitored by Pr.203.
l Under this application, the value of Pr.561~Pr.563 should set in the range of
0~1023.
78 OL WARNING When Pr.054 =11, the OL level can be monitored by Pr.061.
79 /(OL WARNING) When DOx assigned to OL Warning function DOx(39), if OL level > 0%, then
DOx(78) will ON.
DOx(79) is complement output of DOx(78).
86 ACCELERATING When DOx assigned to ACCELERATING function DOx(86), if drive is
increasing its output speed, then DOx(86) will ON.
87 DECELERATING When DOx assigned to DECELERATING function DOx(87), if drive is
decreasing its output speed, then DOx(87) will ON.

51
200 DI0 STATUS l When DI0~DI6 input status is ON, the corresponding digital output terminal
201 DI1STATUS DOx(200)~DOx(206) will ON.
202 DI2 STATUS l When DI0~DI6 input status is OFF, the corresponding digital output terminal
203 DI3 STATUS DOx(200)~DOx(206) will OFF.
204 DI4 STATUS l This function is used to monitor DI0~DI6input status, and can used to
205 DI5 STATUS control output status of DOx by DI0~DI6.
206 DI6 STATUS

52
9. RS485 Communication
9.1 RS485 Communication Port Related Parameters
The following parameters must pre-assigned before use RS485 communication function.
Pr.nnn Parameter Name Description
120 Protocol Select
Pr.120 Protocol Remarks
0 JPS Protocol
1 JPS Modbus(RTU) JPS Modbus Protocol, use for the master
can only assign one slave ID.
2 Profibus-DP
3 Modbus(RTU) Standard Modbus protocol
121 Baud Rate
Pr.121 Baud Rate
0 4800
1 9600
2 19200
3 38400
122 Stop Bit
Pr.122 Stop Bit
0 1
1 2
123 ID This parameter is used to assign the Communication Address while this drive controlled
RS485 communication port. Computer may control any drive by select its corresponding
ID
Pr.120 Pr.123 Range
0 1~99
1 0~250
2 Consult to our R&D department
3 0~250
124 Queue Status Monitors the number of data is queue up to write into EAROM memory.
125 Parity
Pr.125 Parity
0 Even
1 Odd
2 None
For JPS Protocol, must use Even Parity.
9.2 RS485 Port Configuration
The drive has a build in RS485 communication port on CON1 of Feedback I/O board, the definition of the connector
pins are:
CON1 (JAM-SC25-05WS)

5:leave this pin open

4:Sig- (B) JP1 jumper of Feedback I/O board is used to select
JP1 With/Without Terminal Resistor.
3:Sig+ (A)
l JP1 on TR position, select with Terminal Resistor.
2: 0V TR l JP1 on NO position, select without Terminal Resistor.
1:+5V NO

l RS485 Port can use to control multiple drives by connect the signal pin in parallel.
l The option of standard cable (CABLE_RS485) is used to transform JAM connector (CON1) into standard 9 pin
D-sub Male connector. The definition of the D-sub connector is:
9pin D-sub Male Connector Definition JAM Connector (CON1)
PIN1~3 N.C.
PIN4 A(SIG+) PIN3
PIN5 B(SIG-) PIN4
PIN6 0V PIN2
PIN7~9 N.C.

53
9.3 JPS Protocol & Format
All code transfer between Computer and Drive are ASCII code, and the “CR” code (0x0D) must add to the end of each
command string.
The communication port must select 7 bit data, Even parity.
9.3.1 Computer to Drive
Computer may send three types of message to drive.
9.3.1.1 Control Command (No response will send back from drive)
Format: “C,uu,cc,fffff”
C : Head of COMMAND String.
uu : ID of drive, from 00 to 99.
If the “uu” code in command string is “00”, all drives can be controlled at the same time.
cc : Control command code, from 00 to 15.
The “cc” number is actually converted from four bits binary data.
cc= 8 * Bit-3(JOG) + 4 * Bit-2(Reverse) + 2 * Bit-1(RUN) + Bit-0(Reset)
Control Code Function
cc=00 Stop
cc=01 Reset
cc=02 Forward Run
cc=06 Reverse Run
cc=10 Forward JOG Run
cc=14 Reverse JOG Run
fffff : Set speed, from 00000 to 09000.

9.3.1.2 Write Command (No response will send back from drive)
format: “W,uu,nnn,ddddd”
W : Head of WRITE String.
uu : ID of drive, from 00 to 99.
If the “uu” code in command string is “00”, all drives can be controlled at the same time.
nnn : Parameter number, from 000 to 999.
ddddd : data value, from 00000 to 65535.
If data exceed upper or lower limit (shown in parameter table) will be trimmed within
boundary automatically.
9.3.1.3 Read Command (Drive will send back P-string after receive this string)
Format: “R,uu,nnn”
R : Head of READ String
uu : ID of drive, from 01 to 99.
Do not specify uu=00 for Read Command while multiple drives are under control.
nnn : Parameter number, from 000 to 999.

54
9.3.2 Drive to Computer
Drive will send back Parameter data and its Status after receive Read Command from computer.
Format: “P,uu,nnn,tt,ddddd,s,aaaa”
P : P stands for PARAMETER String
uu : ID of drive, from 00 to 99.
This number is defined in Pr.093 of each drive.
nnn : Parameter number, from 000 to 999.
tt : Data type of this parameter, from 00 to 22.
tt Data Type Data Range Format
0 Read/Write, store in EAROM 00000~65535 999.99
1 Read/Write, store in EAROM 00000~65535 9999.9
2 Read/Write, store in EAROM 00000~65535 99999
3 Read/Write, store in EAROM 00000~00255 999.99
4 Read/Write, store in EAROM 00000~00255 9999.9
5 Read/Write, store in EAROM 00000~00255 99999
6 Read/Write, store in EAROM 00000~00001 99999
7 Read/Write, store in RAM 00000~65535 99999
999.99, if data >32767 which is
8 Read only, store in RAM 00000~65535
-(65536-ddddd)
9 Read only, store in RAM 00000~65535 999.99
10 Read only, store in RAM 00000~65535 9999.9
11 Read only, store in RAM 00000~65535 99999
12 Read only, store in RAM 00000~00255 999.99
13 Read only, store in RAM 00000~00255 9999.9
14 Read only, store in RAM 00000~00255 99999
15 Read only, store in RAM 00000~00001 99999
16 Read only, store in RAM 00000~00015 99999, (Binary)
17 Read only, store in RAM 00000~00007 99999, (Binary)
18 Read only, store in RAM 00000~00003 99999, (Binary)
19 Read only, store in RAM 00000~01023 99999
20 Read only, store in RAM 00000~00001 99999, (Hex)
22 Read only, store in RAM 00000~00001 99999, (Hex)
ddddd : Data value, from 00000 to 65535.
s : Drive output status, from 0 to 9.
s = 1 : Drive Reverse Running
s = 2 : Drive Forward Running.
s = 3 : Drive Stop
else, undefined.
aaaa : Alarm history, from 0000 to 9999
The drive can record 4 Alarm messages.
Most significant digit stands for oldest Alarm message.
Least significant digit stands for present Alarm message.
Refer to section 5.2.8 (Pr.013) for Alarm code.

55
9.4 HMI Protocol (Modbus(RTU))
The option of Modbus(RTU) interface let drive simulate as Modicon PLC and can connect with HMI directly. Up to 8
drives can be controlled by one HMI for direct control and monitor.
9.4.1 Parameter Setting
9.4.1.1 HMI Setting
In fact, the drive simulate as Modicon PLC when connect with HMI, so communication protocol is similar to standard
Modus(RTU).
l Select Modbus(RTU)
l HMI serves as Master, address select “0”
l Drive serves as Slave, address select “1”.
l Data Bit select 8 bit data.
l Select Baud, Stop Bit and Parity.

9.4.1.2 Drive Setting

l Pr.120 = 1 or 3, select Modbus(RTU).
l Pr.121 = 0/1/2, select Baud Rate. 0 : 4800, 1 : 9600, 2 : 19200
l Pr.122 = 0/1, select Stop Bit. 0 : 1 stop bit, 1 : 2 stop bits
l Pr.123 = ID,
l If Pr.120 = 1, select JPS Modbus(RTU) protocol, ID selection as:
Drive 1, select ID=01
Drive 2, select ID=11
Drive 3, select ID=21
﹕
﹕
Drive 8, select ID=71
If Pr.120 = 3, select Modbus(RTU) protocol, Pr.123 select as Slave ID
l Pr.125 = 0/1/2., select Parity. 0 : Even 1 : Odd, 2 : No Parity
NOTE: These parameters only effect after RESET.

9.4.2 Definition of Modbus(RTU) and Drive

When HMI communicate with Slave of Modbus(RTU), the address definition is:
l 0x 1 ~ 0x 10000, Bit for Read/Write
l 1x 1 ~ 1x 10000, Bit for Read only
l 3x 1 ~ 3x 10000, Word for Read only
l 4x 1 ~ 4x 10000, Word for Read/Write
l 4L 1 ~ 4L 10000, Long Word for Read/Write

9.4.2.1 Corresponding Table of Read/Write Bit

HMI Address Digital Input Description
0x 1 DI0 l If HMI input Bit (0x 1 ~ 0x 11) = 1, means
0x 2 DI1 the corresponding DIx is ON.
0x 3 DI2 l If HMI input Bit (0x 1 ~ 0x 11) = 0, means
0x 4 DI3 the corresponding DIx is OFF.
0x 5 DI4
0x 6 DI5
0x 7 DI6
0x 8 DI7
0x 9 DI8
0x 10 DI9
0x 11 DI10
0x 12 DI11
0x 13 DI12
0x 14 DI13
0x 15 DI14
0x 16 RESET 0x 16 =1, drive execute RESET.

56
9.4.2.2 Corresponding Table of Read Only Bit
HMI Address Status Description
1x 1 DI0 l If the reading of HMI Bit = 1, means the
1x 2 DI1 input states of corresponding DIx is ON.
1x 3 DI2 l If the reading of HMI Bit = 0, means the
1x 4 DI3 input states of corresponding DIx is OFF.
1x 5 DI4
1x 6 DI5
1x 7 DI6
1x 8 DI7
1x 9 DI8
1x 10 DI9
1x 11 DI10
1x 12 DI11
1x 13 DI12
1x 14 DI13
1x 15 DI14
1x 16 Reserve
1x 17 DO0 l If the reading of HMI Bit = 1, means the
1x 18 DO1 Output states of corresponding DOx is ON.
1x 19 DO2 l If the reading of HMI Bit = 0, means the
1x 20 DO3 Output states of corresponding DOx is OFF.
1x 21 DO4
1x 22 DO5
1x 23 DO6
1x 24 ~ 1x 31 Reserve
l 1x 32 =0, Drive is normal
1x 32 Drive Status
l 1x 32 =1, Drive under Alarm

9.4.2.3 Corresponding Table of Read Only Word

HMI Address Parameter number
3x1 Pr.000
3x 2 Pr.001
3x 3 Pr.002
﹕ ﹕
﹕ ﹕
3x998 Pr.997
3x999 Pr.998
3x1000 Pr.999

9.4.2.4 Corresponding Table of Read/Write Word

HMI Address Parameter number
4x1 Pr.000
4x 2 Pr.001
4x 3 Pr.002
﹕ ﹕
﹕ ﹕
4x998 Pr.997
4x999 Pr.998
4x1000 Pr.999

9.4.2.5 Corresponding Table of Read/Write Long Word

HMI Address Parameter number
4L1 Pr.001(H)/Pr.000(L)
4L 2 Pr.002(H)/Pr.001(L)
4L 3 Pr.003(H)/Pr.002(L)
﹕ ﹕
﹕ ﹕
4L998 Pr.998(H)/Pr.997(L)
4L999 Pr.999(H)/Pr.998(L)
4L1000 Not Allow

57
10. Block Diagram of PDS Drive

R U

POWER S V
NFB IGBT Motor PG
SOURCE
T W
*1
E P

*1 B
15pin
BRAKE
N D-sub

X,Y pulse input command

9pin D-sub CON5 CON3 Feed Back
A,B pulse output
PC,MMI, RS485 CON1 CON4 9pin D-sub
PLC, etc.
Feed Back
DI7 Option AO2
DI8 AO3
DI9 ACOM
DI10
DO4
DO5
DO6

CON

AI1 AO1
AI2
AI3
Field Bus Option
5V
ACOM CON Master

DI1 JP5
CON DO select
DI2
type1
DI3 (NPN)
DI4
JP4 DI5 DO1 JP5
DI select DO2 DO select
DI6
type2 type2
RST CPU (PNP)
(PNP)
BOARD RY1
24V Relay
DCOM RY2 Output
JP4
DI select
type1
Shield
(NPN)
*1 Drive and Motor must connect Earth properly and separately.

58
11. Special Function
11.1 MARK Function
Under Auto Point-To-Point control mode, use this function to identify printing mark with Mark Sensor.
11.1.1 Parameters Description
Length parameters
l DL0(Pr.501/500) defines Cutting Length.
l DL2(Pr.505/504) defines First Length after Mark signal appeared.
l DL5(Pr.511/510) defines Second Length after Mark signal appeared.

Mark Parameters
l The areas of Mark signal may appear call “Window”.
l DL3(Pr.507/506) defines Lower Limit of Window.
l DL4(Pr.509/508) defines Upper Limit of Window.
l The Mark signal must input from DI2(180).
l The Mark signal only validate when the feed length between the length of DL4 and DL3.
l When execute Auto Point To Point function
If the Valid Mark signal appeared, the destination length is DL2 (or DL5) from Mark position.
If the Valid Mark signal not appeared, the destination length is DL0.

Mark-Loss Output
l DOx(180) serves as Mark-Loss output function
l DOx(180) will be OFF when start Auto-Point-To-Point function.
l If the Mark signal appears in the range of Window, DOx(180) remains OFF.
l If the Mark signal not appear in the range of Window, DOx(180) become ON.

Length Conversion
l Pr.576/577 defines the actual physical length in micrometer when motor rotates on revolution. (μm /revolution)
l Set Pr.334/384/434/484=6, 6 data to be converted micrometer into clocks.
l DL16 (μm in Pr.533/532)àDL0 (cks in Pr.501/500)
l DL18 (μm in Pr.537/536)àDL2 (cks in Pr.505/504)
l DL19 (μm in Pr.539/538)àDL3 (cks in Pr.507/506)
l DL20 (μm in Pr.541/540)àDL4 (cks in Pr.509/508)
l DL21 (μm in Pr.543/542)àDL5 (cks in Pr.511/510)
l Select DL2 or DL5 by DIx(155)
1. If DIx(155) OFF, DL18(àDL2) selected (first Length after Mark signal appeared).
2. If DIx(155) ON, DL21(àDL5) selected (second Length after Mark signal appeared)
3. If DIx(155) not selected, DL18(àDL2) selected.

Mark Setting
l Set DL16 = length between two mark (Cutting Length in μm)
l Define the tolerance between two mark as MarkTolerance
l Set DL18 = 2 * MarkTolerance (first Length after Mark signal appeared)
l Set DL20 = DL16 – 1 * MarkTolerance (Window Upper Limit)
l Set DL19 £ DL16 – 3 * MarkTolerance (Window Lower Limit)

59
11.1.2 Running Status Monitor
Example for Long Cutting Length

Trigger Start Trigger Start

DIx(118)

Servo End
DOx(124)

AOx(3)
(Speed)

Acc Torque

AOx(8)
(Torque)

Dec. Torque

Error is large while moving

Error is zero after
Servo End.
AOx(12)
(P. Error)

Remarks:
1. AOx(3), AOx(8), AOx(12) are used to monitor Running Speed Curve, Torque Demand Curve and
Position Error Curve respectively. Refer to section 5.2.6
2. All the AOx outputs have 10ms RC Filter in side, the observed curve is distorted.
3. If AOx(3) = 10V, Speed = maximum speed limit (Pr.315/365/415/465)
4. If AOx(8) = 10V, Torque = maximum torque limit (Pr.312/362/412/462)
5. If AOx(12) = 10V, Error = clocks defined in Pr.570
6. The AOx(8) is used to gauge the selection of power range for drive and motor.
7. The AOx(12) is used to gauge the settling time of motor.

60
Example for Short Cutting Length

DIx(118) Trigger Start Trigger Start

Servo End
DOx(124)

Before and after Mark,

the speed slope should be same.
AOx(3)
(Speed)

Window

DOx(181)

Mark

DI2(180)

61
11.1.3 S Ramp Curve
Set Pr.344/394/444/494=1 and then RESET to select APTP S-curve acceleration/deceleration.
Example for Short Cutting Length with S Ramp

Trigger Start Trigger Start

DIx(118)

Servo End

DOx(124)

Before and after Mark,

the speed slope should be same.
AOx(3)
(Speed)

Window
DOx(181)

Mark
DI2(181)*

MARK Loss

DOx(180)

This signal active when “Mark” didn’t appear within Window

Will remain inactive if “Mark” appear within Window
Remarks:
l The Mark signal must input from DI2(181).
l Pr.559/558, Pr.561/56, Pr.563/562 are define as new function; do not use them for length setting.
l Pr561~Pr.563 define as Torque Compensation for improving Position Error.
1. If Pr.561=0, Pr.562 defines the rate of Acceleration Torque Compensation (9999=99.99%)
Pr.563 defines the rate of Deceleration Torque Compensation (9999=99.99%)
2. 令 Pr.561=1, Select Auto Torque Compensation.
l Pr.558 and Pr.559 used to define Window2
1. Pr.558 defines Lower Limit of Window2 (9999 = 99.99% of Set Length)
2. Pr.559 defines Upper Limit of Window2 (9999 = 99.99% of Set Length)
3. The DOx(150) will ON, if feed length > Pr.558 (Lower Limit of Window2)
4. The DOx(151) will ON, if feed length < Pr.559 (Upper Limit of Window2)
5. The DOx(152) will ON, if feed length in the position rang of Window2.
l Pr.583/582 used to monitor the feed length in Hex Form.
When Mark Input (DI2(180) or DI2(181)) is selected, if DIx(118) triggered, Pr.583/582 will be cleared to 0.
l Pr.735/734 is used to display last feed length in Hex Form.

62
JPS JOINT PEER SYSTEC CORP.
No.57, Ln. 33, Sec. 5, Zhonghe St.,2nd floor,
Xinshe Dist., Taichung City 426, Taiwan
TEL: 886-4-25816866 FAX: 886-4-25814889
http://www.jps.com.tw
E-mail: [email protected]

63