SSP10/2150A
Satellite Power-Conditioned Distribution System
Installation and
Operation Manual
Operation
Ph: 800-421-6511 www.picomacom.com Manual
Rev. 06/03
Safeguards
SSP10/2150A
Product Inspection
Inspect the equipment for shipping damage. Should any damage be discovered, immediately file a claim with the carrier.
Important Safety Instructions
To insure proper installation and operation, take a moment to read this guide before proceeding with the installation. If you have any
questions or comments about the SSP10/2150A satellite power-conditioned distribution system, please contact your dealer or have him contact the
PICO MACOM Service Center at these phone numbers: 800-421-6511, 818-493-4300.
The lightning flash with arrowhead symbol, within an The exclamation point within an equilateral triangle is
equilateral triangle, is intended to alert the user to the intended to alert the user to the presence of important
presence of un-insulated “dangerous voltage” within the operating and maintenance (servicing) instructions in
product’s enclosure that may be of sufficient magnitude the literature accompanying the appliance.
to constitute a risk of electric shock to persons.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN
EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED
TO PREVENT BLADE EXPOSURE.
ATTENCION: POUR PREVENIR LES CHOCS ELECTRIQUES, NE PAS UTILISER CETTE FICHE POLARISEE AVEC
UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI
LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
1. Read Instructions: All safety and operating instructions should 8. Accessories: Do not place this product on an unstable cart,
be read before the appliance is operated. stand, tripod, bracket, or table. The product may fall, causing serious
injury to a child or adult, and serious damage to the appliance.
2. Retain Instructions: The safety and operating instructions should
be retained for future reference. 9. Ventilation: This video product should never be placed near or
over a radiator or heat register. This video product should not be
3. Heed Warnings: All warnings on the appliance should be adhered
placed in a built-in installation such as a bookcase or rack unless
to. proper ventilation is provided or the manufacturer’s instructions have
4. Follow Instructions: All operating and user instructions should be been adhered to. Any slots or opening in the cabinet are provided for
followed. ventilation. To ensure reliable operation of the video product and to
protect it from overheating, these openings must not be blocked or
5. Cleaning: Unplug this appliance from the wall outlet before covered. Openings should never be blocked by placing the product
cleaning. Use a damp cloth for cleaning. Do not use liquid cleaners on a bed, sofa, rug, or other similar surface.
or aerosol cleansers.
10. Grounding or Polarization: This video product is equipped
6. Do Not Use Attachments: Use of attachments not recommended with either a three prong plug for 110 VAC use or a two prong flat
by the manufacturer may cause hazards. blade 220 volt type plug. Each type is to be inserted into only the
7. Water and Moisture: Do not use this product near water—for type of receptacle for which they specifically designed. Do not cut
example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet off the round grounding pin in order to be able to fit into a two prong
basement, or near a swimming pool—and the like. receptacle as this could cause injury and will void the warranty.
2 Ph: 800-421-6511 www.picomacom.com
Rev. 06/03
Safeguards
SSP10/2150A
11. Power Sources: This product should be operated only from
the type of power source indicated on the marking label. If you are
not sure of the type of power supplied to your home, consult your
appliance dealer or local power company.
12. Power-cord Protection: Power-supply cords should be routed
so they are not likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to cords and plugs,
convenience receptacles, and the point where they exit from the
appliance.
13. Lightning: For added protection for this product during a lightning
storm, or when it is left unattended or unused for long periods of time,
the unit should be disconnected from power source.
14. Power Lines: An outside antenna system should not be located
in the vicinity of overhead power lines, other electric light or power
circuits, where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them
may be fatal.
15. Overloading: Do not overload wall outlets and extension cords as
this can result in risk of fire or electric shock.
16. Object and Liquid Entry: Never push objects of any kind into
this product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing: Do not attempt to service this product yourself as 21. Outdoor Antenna Grounding: Before attempting to install this
opening or removing covers may expose you to dangerous voltage or product, be sure the antenna or cable system is grounded so as to
provide some protection against voltage surges and built-up static
other hazards. Refer all servicing to qualified service personnel.
charges.
18. Damage Requiring Service: Unplug this product from the wall
a. Use No.10 AWG (5.3mm) copper, No.8 AWG (8.4mm)
outlet and refer servicing to qualified service personnel under the
aluminum, No.7 AWG (10mm) copper-clad steel or bronze wire or
following conditions: larger, as ground wire.
a. When the power-supply cord or plug is damaged. b. Secure antenna lead-in and ground wires to house with
b. If liquid has been spilled, or objects have fallen into the product. stand-off insulators spaced from 4 feet (1.22m) to 6 feet (1.83m)
apart.
c. If the product has been exposed to rain or water.
c. Mount antenna discharge unit as close as possible to where
d. If the product does not operate normally by following the lead-in enters house.
operating instruction. Adjust only those controls that are covered
by the operating instructions. An improper adjustment may result d. A driven rod may be used as the grounding electrode where
in damage and will often require extensive work by a qualified other types of electrode systems do not exist. Refer to the
technician to restore the product to its normal operation. National Electrical Code, ANSI/NFPA 70-1984 for information.
e. If the product has been dropped or the cabinet has been e. Use jumper wire not smaller than No.6 AWG (13.3mm) copper
damaged. or equivalent, when a separate antenna grounding electrode is
used.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
NOTE TO THE CATV SYSTEM INSTALLER
19. Replacement Parts: When replacement parts are required, be
sure the service technician has used replacement parts specified by THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM
the manufacturer or have the same characteristics as the original INSTALLER’S ATTENTION TO ARTICLE 820-22 OF THE NEC
parts. Unauthorized substitutes may result in fire, electric shock or THAT PROVIDES GUIDELINES FOR PROPER GROUNDING
other hazards. AND, IN PARTICULAR, SPECIFIES THAT THE CABLE
20. Safety Check: Upon completion of any service or repairs to GROUND SHALL BE CONNECTED TO THE GROUNDING
this product, ask the service technician to perform safety checks to SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF
determine that the product is in proper operating conditions. CABLE ENTRY AS PRACTICAL.
Ph: 800-421-6511 www.picomacom.com 3
Rev. 06/03
Descriptions
SSP10/2150A
Satellite Power-Conditioned Distribution System
Distribution system compactly
combines LNB powering, signal
separation, and amplification in a
single rack space
Fully-conditioned power source
eliminates power drawn from
receiver, reducing heat buildup and
increasing product life
Dual independent 1000mA
high-capacity supplies have ample
power reserve to reliably feed
multiple line amplifiers
5 amplified outputs per
polarity provide for multiple
receiver flexibility
Single polarity configuration
SSP10/2150A
Satellite Power-Conditioned Distribution System
provides 9 outputs for maximum
receiver operation
Pico Macom’s SSP10/2150A is an L-band satellite power-conditioned distribu-
Front panel LED’s provide quick tion system, compactly combining multiple functions into a single rack unit. The
and easy LNB open-or-short
status monitoring unit powers two satellite LNB polarities in the 950-2150 MHz range, amplifies
and splits the signals for distribution to multiple satellite receivers. Two high
Automatic current sensing enables
short circuit shutdown protection capacity 1000mA power supplies provide enough power for each LNB polarity
to safeguard from potential and several line amplifiers, reducing wear-and-tear on commercial receivers.
damage while servicing LNBs
Front panel current-sensing indicators warn of system faults and allow quick
Plug-in external UL approved system status. Pico Macom backs up this product with its industry leading
power adapter supplied for ease
of installation and to reduce heat 5-year limited warranty.
build-up within the unit
4 Ph: 800-421-6511 www.picomacom.com
Rev. 06/03
Specifications
SSP10/2150A
Satellite Po
Front View
+ + + +
24Vdc
VERT
1A
TO HIGH
LNB OUTPUT 1 2 3 4 5 OUTPUT
HORZ
+ +
Rear View
Specifications General
LNB Power: 18 VDC regulated, 1000mA Power Input: 24VDC 1000mA
Isolation: 10 dB Operating Temperature: -10° to +50° C
Voltage Output: 18 VDC @ 250 mA Dimensions: 19˝(L) x 3˝(D) x 13/4˝(H)
Current Limiting: 1A each max Weight: 6.5 lbs.
Line Regulation: ±0.2 VDC w 100mA load
Ripple Voltage: 20mV max
Frequency: 950-2150 MHz
Gain: 1dB, 4-Vertical Outputs,
4-Horizontal Outputs Ordering Information
5dB, 1 Vertical Output,
1-Horizontal Output
Input Voltage: 105-125 VAC SSP10/2150A
Indicators: V/H Power supply ON
V/H Power supply Short Circuit
V/H Power supply Open Circuit
Ph: 800-421-6511 www.picomacom.com 5
Rev. 06/03
Operation and Controls
SSP10/2150A
1 2 3 2 3
Front Panel Control
1. Power Supply Status: 3. “SC”
This LED indicates power is being supplied to the unit from the wall The “SC” LED’s indicate a short between the SSP-10 and the LNB.
adaptor. Both will activate if either vertical or horizontal polarity are in a short
circuit condition. It is recommended to deactivate the SSP10/2150A
2. “OC” until the problem is corrected.
When the “VERTICAL OC” is lit, this indicates an open circuit at the
vertical LNB. When the “HORIZONTAL OC” is lit, this indicates an
open circuit at the horizontal LNB.
1 2 3 3 3 3 4 5
+ + + +
24Vdc
VERT
1A
TO HIGH
LNB OUTPUT 1 2 3 4 5 OUTPUT
HORZ
+ +
Back Panel Control
1. LNB Inputs: 4. Vertical and Horizontal Adjustments:
These inputs provide DC power to the LNBs. If the “OC” LED remains on after the LNBs are connected to the
SSP10/2150A, Rotate the adjustment (top of case) until the LED
2. High Outputs: shuts off.
These outputs provide an additional 6 dB of signal to the input of the
receivers if needed 5. Power Jack:
Input jack for 24Vdc, 1A wall adapter.
3. Outputs to Receivers:
These outputs provide approximately the same signal level to the
input of the receivers as that of the LNBs, less cable loss.
6 Ph: 800-421-6511 www.picomacom.com
Rev. 06/03
Installation Procedure
SSP10/2150A
Installation Signal Combining Methods
It is recommended that assistance be available to safely install equipment PICO MACOM recommends connecting the headend components in
in equipment racks. the following manner: Each of the modulators, signal processors or
strip amplifiers output are connected to a combining network. Either a
1. Install chassis in equipment rack (equipment rack sold separately) PHC-12G or a PHC-24G headend combiner may be used to accomplish
by supporting the bottom and rear of SSP10/2150A at the desired this purpose.
elevation in rack.
2. Line up the side holes of chassis with the tapped equipment rack The PHC-12G or PHC-24G passive headend combiner consists of two
holes. rows of directional couplers combined by a hybrid splitter. Normally,
3. Insert the provided screws through the mounting holes at the the odd channels are combined on one row while even channels are
extreme left and right of faceplate and thread into the tapped combined on the other row of directional couplers for maximum isolation.
equipment rack holes. The output of the combiners may be connected to the input of a launch
4. Fasten the bottom screws first, then fasten top screws. (tighten securely). amplifier such as a CA-30RK550 or CA-30RK1000. The output of the
5. Connect a cable from the satellite vertical polarity low noise block amplifier is connected to the main distribution line.
converter (LNB) to the vertical input connector of the SSP10/2150A.
6. Connect a cable from the satellite horizontal polarity low noise block The CHC16U/550 and CHC16U/860 sixteen channel active combiners
converter (LNB) to the horizontal input connector of the SSP10/2150A. provides both signal combining and post amplification of the headend
7. Connect a cable from the output connector the SSP10/2150A to the signals. Up to 16 channels may be combined using the CHC16U. The
input of a satellite receiver combiner gain is 15 dB per channel.
8. Plug the wall adaptor plug into the jack located in the back of the unit. A 24 channel system hook-up is shown. (The same combining result may
9. Plug the adaptor into a 120Vac, 60Hz wall receptacle. be accomplished by using a single PHC-24G).
The two PHC-12G outputs are combined via a two-way splitter, which is
connected to a CA-30RK1000 launch amplifier. The input levels to the
combiner, whether from a modulator, signal processor or a strip amplifier,
must be at the same amplitude.
Ph: 800-421-6511 www.picomacom.com 7
Rev. 06/03
Warranty
SSP10/2150A
Limited Warranty
Pico Macom warrants to the original purchaser that all of its new products are of sound design, quality materials and workmanship at the time of manufacture and will be
free from related defects for one year from the original purchase date. Pico Macom will repair or, at its discretion, replace without cost to the original purchaser, the product
which, upon inspection by Pico Macom, appears to be defective or not conforming to factory specifications. Pico Macom will cover the cost of parts, labor, and return freight
from factory.
Five-Year Limited Warranty
Most products designated as “Headend Electronics” are further covered by an extended 4-year period beyond the expiration of the original 1-year warranty, for a full 5-year
period. Qualified equipment requiring factory repair during the extended 4-year period is covered under our re-certification program. Re-certification fees under this program
shall not to exceed 20% of the product’s List Price and whenever possible, Pico Macom will attempt to upgrade performance to the latest improved specification.
Warranty Limitations
This warranty excludes coverage of damage or inoperability resulting from (1) use or installation other than in strict accordance with Pico Macom’s written instructions,
(2) disassembly or repair by someone other than Pico Macom or a Pico Macom authorized repair center, (3) misuse, misapplication or abuse, (4) alteration, (5) lack of
reasonable care or (6) wind, ice, snow, rain, lightning, power surges, or any other weather conditions or acts of God. Pico Macom’s warranty with respect to third-party proprietary
sub-assembly modules and/or private-label products are limited to the duration and terms of third-party vendors’ warranty. Pico Macom shall in no event and under no
circumstances be liable or responsible for any consequential, indirect, incidental, punitive, direct or special damages based upon breach of warranty, breach of contract,
negligence, strict tort liability or otherwise or any other legal theory, arising directly or indirectly from the sale, use, installation or failure of any product acquired by buyer from
Pico Macom. This limited warranty extends to the original purchaser. Pico Macom reserves the right to modify or discontinue this warranty at Pico Macom’s sole discretion
without notification. No other warrantees are expressed or implied.
Uptime Loaner Program
Our Uptime loaner program is designed to provide domestic users of our headend products and commercial systems the best possible support and service. This program is
established to minimize downtime resulting from equipment failure in critical service situations. We offer this program free-of-charge (excluding freight) to qualified purchasers
within the warranty period. The program provides a free equipment loan of like qualified equipment enabling seamless operation for the time required to repair and return the
unit.
The process is simple. Call our Customer Service desk requesting a return-merchandise-authorization (RMA) number for the failed equipment and ask for a loaner unit. We will
issue an invoice for the List Price of the loaner unit plus shipping costs. When you receive the loaner unit, pack the failed unit in the loaner unit’s box and ship it freight prepaid
to Pico Macom for repair. When you receive the repaired unit, a new RMA number will be provided in the box. Carefully pack the loaner unit and affix the new RMA number
on the box and ship it back to us for full credit excluding shipping costs.
To qualify for the program, you must have current open-terms with us and in good standing. We must receive your failed unit within one week after the loaner unit is shipped to
you, and must likewise receive the loaner unit within one week after the repaired unit is shipped back to you. Daily rental fees not to exceed 10% of the equipment’s List Price
will apply beyond one week after the loaner or repaired unit are shipped to you. Other limitations may apply, so please call us for additional information on qualifying equipment
and procedures. Pico Macom reserves the right to modify or discontinue the Uptime Loaner Program at any time, and at its sole discretion.
Damage or Shortage Claims
Our shipping staff carefully packs and ships your orders in compliance with common carriers’ requirements. Please make note of any obvious damage or shortage on the freight
bill or carrier’s receipt next to your signature. The carrier’s agent must too sign acknowledging the loss. Failure to do so may result in the carrier’s refusal to honor the claim.
Please open your order immediately upon receipt to check for concealed damage and compare the packing list to the items shipped. If damaged, keep the original shipping
cartons for possible inspection by the carrier. You must report claims for loss or damage within 3 days of delivery, while claims for erroneous charges or price corrections must
be presented within 30 days of invoice date.
Returning Shipped Items
To return any shipped items, including those shipped for warranty repairs or credit, call our Customer Service desk to request a Return Merchandise Authorization (RMA)
number. Please reference the original invoice number and purchase date, and product serial number (if any). Be certain to mark the RMA number on the package boldly and
legibly. Unless we specify a different carrier, please ship your returned items to us via UPS freight prepaid and fully insured. If returned for credit, we will promptly process
your request upon receipt of your return order.
Our Return Policy: Your Satisfaction Guaranteed
Our goal is your complete satisfaction. If for any reason, our products were not quite what you anticipated, simply call your customer service rep and we will be
happy to assist you in replacing or returning the order. You may return current, non-discontinued items for full credit for up to 30 days from invoice date. Our
requirements are simple: Excepting defective items, the products must be returned in their original packaging and in re-salable condition. Restocking fees may
otherwise apply beyond this period or if products are not returned in their original condition. Please contact your customer service rep for more information.
8 Ph: 800-421-6511 www.picomacom.com
Rev. 06/03
