PIC18F66K80 FAMILY

28/40/44/64-Pin, High-Temperature, Enhanced Flash

Microcontrollers with ECAN™ and nanoWatt XLP Technology
High-Temperature Features: ECAN Bus Module Features (Continued):
• Ambient Temperature Range of -40°C to +150°C • Six Programmable Receive/Transmit Buffers
• Three Dedicated Transmit Buffers with Prioritiza-
Power-Managed Modes: tion
• Run: CPU on, Peripherals on • Two Dedicated Receive Buffers
• Idle: CPU off, Peripherals on • 16 Full, 29-Bit Acceptance Filters with Dynamic
• Sleep: CPU off, Peripherals off Association
• Two-Speed Oscillator Start-up • Three Full, 29-Bit Acceptance Masks
• Fail-Safe Clock Monitor (FSCM) • Automatic Remote Frame Handling
• Power-Saving Peripheral Module Disable (PMD) • Advanced Error Management Features
• Ultra Low-Power Wake-up
Special Microcontroller Features:
• Fast Wake-up, 1 µs, Typical
• Low-Power WDT, 300 nA, Typical • On-Chip 3.3V Regulator
• Run mode Currents Down to Very Low 3.8 µA, • Operating Speed up to 64 MHz
Typical • 3.6 Kbytes of General Purpose Registers (SRAM)
• Idle mode Currents Down to Very Low 880 nA, • Three Internal Oscillators:
Typical - LF-INTOSC (31 kHz)
• Sleep mode Currents Down to Very Low 13 nA, - MF-INTOSC (500 kHz)
Typical - HF-INTOSC (16 MHz)
• Priority Levels for Interrupts
ECAN Bus Module Features: • 8 x 8 Single-Cycle Hardware Multiplier
• Conforms to CAN 2.0B Active Specification • Extended Watchdog Timer (WDT):
• Three Operating modes: - Programmable period from 4 ms to 4,194s
- Legacy mode (full backward compatibility with • In-Circuit Serial Programming™ (ICSP™) via Two
existing PIC18CXX8/FXX8 CAN modules) Pins
- Enhanced mode • In-Circuit Debug via Two Pins
- FIFO mode or programmable TX/RX buffers • Programmable BOR
• Message Bit Rates up to 1 Mbps • Programmable LVD
• DeviceNet™ Data Byte Filter Support

TABLE 1: DEVICE COMPARISON

Comparators

BORMV/LVD
8-Bit/16-Bit
12-Bit A/D
Channels

EUSART

ECAN™
Timers

Data Data
CTMU

MSSP
ECCP
CCP/

DSM

Program
Device Memory EE Pins I/O
Memory
(Bytes) (Bytes)

PIC18F25K80 32 Bytes 3,648 1,024 28 24 1 8-ch 4/1 2/3 2 2 1 1 Yes No

PIC18F26K80 64 Bytes 3,648 1,024 28 24 1 8-ch 4/1 2/3 2 2 1 1 Yes No
PIC18F45K80 32 Bytes 3,648 1,024 40/44 35 1 11-ch 4/1 2/3 2 2 1 1 Yes No
PIC18F46K80 64 Bytes 3,648 1,024 40/44 35 1 11-ch 4/1 2/3 2 2 1 1 Yes No
PIC18F65K80 32 Bytes 3,648 1,024 64 54 1 11-ch 4/1 2/3 2 2 1 1 Yes Yes
PIC18F66K80 64 Bytes 3,648 1,024 64 54 1 11-ch 4/1 2/3 2 2 1 1 Yes Yes

 2012 Microchip Technology Inc. DS30509A-page 1

PIC18F66K80 FAMILY
Peripheral Highlights: • Up to Four External Interrupts
• Five CCP/ECCP modules: • One Master Synchronous Serial Port
(MSSP) module:
- Four Capture/Compare/PWM (CCP) modules
- 3/4-wire SPI (supports all four SPI modes)
- One Enhanced Capture/Compare/PWM
(ECCP) module - I2C™ Master and Slave modes
• Five 8/16-Bit Timer/Counter modules: • Two Enhanced Addressable USART modules:
- Timer0: 8/16-bit timer/counter with 8-bit - LIN/J2602 support
programmable prescaler - Auto-Baud Detect (ABD)
- Timer1, Timer3: 16-bit timer/counter • 12-Bit A/D Converter with up to 11 Channels:
- Timer2, Timer4: 8-bit timer/counter - Auto-acquisition and Sleep operation
• Two Analog Comparators - Differential Input mode of operation
• Configurable Reference Clock Output • Data Signal Modulator module:
• Charge Time Measurement Unit (CTMU): - Select modulator and carrier sources from
- Capacitance measurement various module outputs
- Time measurement with 1 ns typical resolution • Integrated Voltage Reference
- Integrated voltage reference

DS30509A-page 2  2012 Microchip Technology Inc.

 PIC18F66K80 FAMILY
Table of Contents
1.0 Device Overview .......................................................................................................................................................................... 5
2.0 Special Features of the CPU........................................................................................................................................................ 7
3.0 Electrical Characteristics .............................................................................................................................................................. 9
Appendix A: Revision History............................................................................................................................................................... 13
The Microchip Web Site ....................................................................................................................................................................... 15
Customer Change Notification Service ................................................................................................................................................ 15
Customer Support ................................................................................................................................................................................ 15
Reader Response ................................................................................................................................................................................ 16
Product Identification System .............................................................................................................................................................. 17

 2012 Microchip Technology Inc. DS30509A-page 3

PIC18F66K80 FAMILY

TO OUR VALUED CUSTOMERS

It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We
welcome your feedback.

Most Current Data Sheet

To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).

Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.

Customer Notification System

Register on our web site at www.microchip.com to receive the most current information on all of our products.

DS30509A-page 4  2012 Microchip Technology Inc.

 PIC18F66K80 FAMILY
1.0 DEVICE OVERVIEW The primary differentiating features and specifications
of the high-temperature PIC18F66K80 family devices
This document contains device-specific information for are:
the following devices, operating in an ambient
• Above +125°C, writes are not allowed for Flash
temperature range between -40°C and +150°C:
program memory
• PIC18F25K80 • PIC18F46K80 • All AC timing specifications are increased by 15%
• PIC18F26K80 • PIC18F65K80 This derating factor includes parameters, such as
• PIC18F45K80 • PIC18F66K80 TPWRT
• Maximum HS frequency of operation is 64 MHz
Note: This data sheet documents only the devices’
features and specifications that are in Note: The test duration for AEC-Q100 reliability
addition to the features and specifications of testing for devices operating at +150°C is
the non-specialty PIC18F66K80 devices. 1,000 hours. Any design operating at
For information on the features and +125°C to +150°C for longer than that
specifications shared by this document’s high- period is not warranted without prior written
temperature devices and the non-specialty approval from Microchip Technology Inc.
devices, see the “PIC18F66K80 Family Data
Sheet” (DS39977).

This family of devices offers the advantages of all

PIC18 microcontrollers; namely, high computational
performance at an economical price. In addition to these
features, the PIC18F66K80 family introduces design
enhancements that make these microcontrollers a logical
choice for many high-performance, power-sensitive
applications.

 2012 Microchip Technology Inc. DS30509A-page 5

PIC18F66K80 FAMILY
NOTES:

DS30509A-page 6  2012 Microchip Technology Inc.

 PIC18F66K80 FAMILY
2.0 SPECIAL FEATURES OF THE 2.1 Device ID Registers
CPU The Device ID registers are read-only registers. They
identify the device type and revision for device
Note: For additional details on the Configuration bits, programmers and can be read by firmware using table
refer to Section 28.1 “Configuration Bits” in reads.
the “PIC18F66K80 Family Data Sheet”
(DS39977). Device ID information presented in
this section is for the high-temperature
PIC18F66K80 family devices only.

TABLE 2-1: DEVICE IDs

Default/
File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Unprogrammed
Value
3FFFFEh DEVID1(1) DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 xxxx xxxx
3FFFFFh DEVID2(1) DEV10 DEV9 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 xxxx xxxx
Legend: x = unknown; u = unchanged,;— = unimplemented.
Note 1: See Register 2-1 and Register 2-2 for DEVIDx values. DEVIDx registers are read-only and cannot be
programmed by the user.

REGISTER 2-1: DEVID1: DEVICE ID REGISTER 1

R R R R R R R R
DEV2(1) DEV1(1) DEV0(1) REV4 REV3 REV2 REV1 REV0
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 7-5 DEV<2:0>: Device ID bits(1)

111 = PIC18F66K80
100 = PIC18F25K80
011 = PIC18F45K80
010 = PIC18F65K80
001 = PIC18F26K80
000 = PIC18F46K80
bit 4-0 REV<4:0>: Revision ID bits
These bits are used to indicate the device revision.

Note 1: These DEV<2:0> values may be shared with other devices. The specific device is always identified by
using the entire DEV<10:0> bit sequence.

 2012 Microchip Technology Inc. DS30509A-page 7

PIC18F66K80 FAMILY
REGISTER 2-2: DEVID2: DEVICE ID REGISTER 2
R R R R R R R R
DEV10(1) DEV9(1) DEV8(1) DEV7(1) DEV6(1) DEV5(1) DEV4(1) DEV3(1)
bit 7 bit 0

Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 7-0 DEV<10:3>: Device ID bits(1)

0110 0000 = PIC18F66K80
0110 0001 = PIC18F46K80, PIC18F26K80, PIC18F65K80, PIC18F45K80, PIC18F25K80

Note 1: These DEV<10:3> values may be shared with other devices. The specific device is always identified by
using the entire DEV<10:0> bit sequence.

DS30509A-page 8  2012 Microchip Technology Inc.

 PIC18F66K80 FAMILY
3.0 ELECTRICAL CHARACTERISTICS
Note: Other than some basic data, this section documents only the high-temperature PIC18F66K80 family devices’
specifications that differ from those of the non-specialty PIC18F66K80 family devices. For detailed information
on the electrical specifications shared by the high-temperature and non-specialty devices, see the
“PIC18F66K80 Family Data Sheet” (DS39977).

Unless otherwise noted, this section’s parameters assume a minimum voltage of 4.0V.

3.1 Absolute Maximum Ratings(†)

Ambient temperature under bias........................................................................................................................... +150°C
Maximum current out of VSS pin .............................................................................................................................60 mA
Maximum current into VDD pin ................................................................................................................................60 mA
Maximum output current sunk by any I/O pin(1) ........................................................................................................1 mA
Maximum output current sourced by any I/O pin(1) ...................................................................................................1 mA
Maximum current sunk by all ports combined(1) .....................................................................................................10 mA
Maximum current sourced by all ports combined(1) ................................................................................................10 mA
Note 1: Maximum allowable current is a function of device maximum power dissipation (see Section 31.0 “Electrical
Characteristics” in the “PIC18F66K80 Family Data Sheet”.

† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above
those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions
for extended periods may affect device reliability.

FIGURE 3-1: PIC18F66K80 VOLTAGE-FREQUENCY GRAPH (HIGH TEMPERATURE)

6.0V
5.5V

5.0V
4.5V
4.0V 4.0V
Voltage

3.5V
3.0V
2.5V
2.0V

64 MHz

Frequency
High-Temperature Devices

 2012 Microchip Technology Inc. DS30509A-page 9

PIC18F66K80 FAMILY
3.2 DC Characteristics: Supply Voltage (High Temperature)
PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated)
(High Temperature) Operating temperature +125°C  TA  +150°C for high temperature
Param
Symbol Characteristic Min Typ Max Units Conditions
No.
D001 VDD Supply Voltage 4.0 — 5.5 V For F devices

3.3 DC Characteristics: Power Down and Supply Current (High Temperature)

PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated)
(High Temperature) Operating temperature +125°C  TA  +150°C for high temperature
Param
Device Typ Max Units Conditions
No.
PIC18FXXK80 Power-Down Current (IPD)(1)
10 28 µA +150°C VDD = 5V, Sleep mode
Module Differential Currents
12 29 µA +150°C VDD = 5V,
Watchdog Timer Current: ΔIWDT
12 28 µA +150°C VDD = 5V, A/D Current: ΔIAD
12 28 µA +150°C VDD = 5V,
High/Low-Voltage Detect: ΔIHLVD
Supply Current (IDD)(2,3)
10 32 mA +150°C VDD = 5V, FOSC = 64 MHz
(PRI_RUN mode)
— 8 mA +150°C VDD = 5V, FOSC = 4 MHz
(PRI_RUN mode)
— 3 mA +150°C VDD = 5V, FOSC = 1 MHz
(PRI_RUN mode)
— 8 mA +150°C VDD = 5V, FOSC = 64 MHz
(PRI_IDLE mode)
— 1.8 mA +150°C VDD = 5V, FOSC = 4 MHz
(PRI_IDLE mode)
— 1 mA +150°C VDD = 5V, FOSC = 1 MHz
(PRI_IDLE mode)
— 28 mA +150°C VDD = 5V, FOSC = 64 MHz
(PRI_RUN mode, 16 MHz w/PLL)
— 8 mA +150°C VDD = 5V, FOSC = 16 MHz
(PRI_RUN mode, 4 MHz w/PLL)
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is
measured with the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS,
and all features that add delta current are disabled (such as WDT, secondary oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as
I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and
temperature, also have an impact on the current consumption.
3: The test conditions for all IDD measurements in active operation mode are:
OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT is enabled/disabled as specified.

DS30509A-page 10  2012 Microchip Technology Inc.

 PIC18F66K80 FAMILY
3.4 DC Characteristics: PIC18F66K80 Family (High Temperature)
PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated)
(High Temperature) Operating temperature +125°C  TA  +150°C for high temperature
Param
Symbol Characteristic Min Typ Max Units Conditions
No.
D031 VIL I/O Ports with Schmitt Trigger VSS — 0.25 VDD V VDD = 5.0V
Buffer
D032 VIL MCLR VSS — 0.25 VDD V VDD = 5.0V
D041 VIH I/O Ports with Schmitt Trigger 0.85 VDD — VDD V VDD = 5.0V
Buffer
D042 VIH MCLR, OSC1 (EC mode) 0.85 VDD — VDD V VDD = 5.0V
D060 IIL Input Leakage Current — — ±2 µA VSS ≤ VPIN ≤ VDD,
I/O Ports Pin at high-impedance

3.5 DC Characteristics: Memory Programming Requirements

PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated)
(High Temperature) Operating temperature +125°C  TA  +150°C for high temperature
Param
Symbol Characteristic Min Typ Max Units Conditions
No.
D120 ED Data EEPROM Memory Byte 50K — — E/W +125°C to +150°C
Endurance
D121 VDRW VDD for Read/Write 4.0 — 5.5 V Using EECON to read/write
PIC18FXXKXX devices
D123 VRETD Characteristic Retention 1 — — Year Provided no other specifications
are violated

 2012 Microchip Technology Inc. DS30509A-page 11

PIC18F66K80 FAMILY
3.6 AC Characteristics Internal RC Accuracy (INTOSC)
PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated)
(High Temperature) Operating temperature -40°C  TA  +150°C

Param
Min Typ Max Units Conditions
No.
INTOSC Accuracy @ Freq = 16 MHz, 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz(1)
OA1 -20 — ±20 % +125°C to +150°C,
VDD = 4.0-5.5V
OA2 LF_INTOSC Accuracy @ 31 kHz
OA2 -25 — ±25 % VDD = 4.0-5.5V
Note 1: Frequency is calibrated at +25°C. The OSCTUNE register can be used to compensate for temperature drift.

TABLE 3-1: DC CHARACTERISTICS: HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS

PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated)
(High Temperature) Operating temperature -40°C  TA  +150°C
Param
Characteristic Min Typ Max Units
No.
D420 HLVD Voltage on VDD, HLVDL<3:0> = 1101 4.00 4.44 4.88 V
Transition High-to-Low HLVDL<3:0> = 1110 4.28 4.75 5.23 V

DS30509A-page 12  2012 Microchip Technology Inc.

 PIC18F66K80
APPENDIX A: REVISION HISTORY
Revision A (February 2012)
Original mini data sheet for the high-temperature
devices in the PIC18F66K80 family.

DS30509A-page 13  2012 Microchip Technology Inc.

PIC18F66K80
NOTES:

DS30509A-page 14  2012 Microchip Technology Inc.

 PIC18F66K80 FAMILY
THE MICROCHIP WEB SITE CUSTOMER SUPPORT
Microchip provides online support via our WWW site at Users of Microchip products can receive assistance
www.microchip.com. This web site is used as a means through several channels:
to make files and information easily available to • Distributor or Representative
customers. Accessible by using your favorite Internet
• Local Sales Office
browser, the web site contains the following
information: • Field Application Engineer (FAE)
• Technical Support
• Product Support – Data sheets and errata,
application notes and sample programs, design • Development Systems Information Line
resources, user’s guides and hardware support Customers should contact their distributor,
documents, latest software releases and archived representative or field application engineer (FAE) for
software support. Local sales offices are also available to help
• General Technical Support – Frequently Asked customers. A listing of sales offices and locations is
Questions (FAQ), technical support requests, included in the back of this document.
online discussion groups, Microchip consultant Technical support is available through the web site
program member listing at: http://microchip.com/support
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives

CUSTOMER CHANGE NOTIFICATION

SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.

 2012 Microchip Technology Inc. DS30509A-page 15

PIC18F66K80 FAMILY
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.

TO: Technical Publications Manager Total Pages Sent ________

RE: Reader Response

From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________ FAX: (______) _________ - _________
Application (optional):
Would you like a reply? Y N

Device: PIC18F66K80 Family Literature Number: DS30509A

Questions:

1. What are the best features of this document?

2. How does this document meet your hardware and software development needs?

3. Do you find the organization of this document easy to follow? If not, why?

4. What additions to the document do you think would enhance the structure and subject?

5. What deletions from the document could be made without affecting the overall usefulness?

6. Is there any incorrect or misleading information (what and where)?

7. How would you improve this document?

DS30509A-page 16  2012 Microchip Technology Inc.

 PIC18F66K80 FAMILY
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO. X /XX XXX
Examples:
Device Temperature Package Pattern a) PIC18F46K80T-H/PT = High Temperature,
Range TQFP package in tape and reel configuration

Device(1,2) PIC18F25K80/26K80, PIC18F45K80/46K80, PIC18F65K80/66K80,

PIC18F25K80/26K80T, PIC18F45K80/46K80T, PIC18F65K80/
66K80T
VDD range 4.0V to 5.5V

Temperature I = -40C to +85C (Industrial)

Range E = -40C to +125C (Extended)
H = -40C to +150C (High Temperature)

Package PT = TQFP Thin Quad Flatpack

MR = QFN Plastic Quad Flat, No Lead Package
SS = SSOP Plastic Shrink Small Outline Note 1: F = Standard Voltage Range
MM = QFN Plastic Quad Flat, No Lead Package 2: LF = Wide Voltage Range
ML = QFN Plastic Quad Flat, No Lead Package
3: T = In Tape and Reel PLCC, and TQFP
packages only
Pattern QTP, SQTP, Code or Special Requirements
(blank otherwise)

 2012 Microchip Technology Inc. DS30509A-page 17

PIC18F66K80 FAMILY
NOTES:

DS30509A-page 18  2012 Microchip Technology Inc.

Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Information contained in this publication regarding device Trademarks

applications and the like is provided only for your convenience
The Microchip name and logo, the Microchip logo, dsPIC,
and may be superseded by updates. It is your responsibility to
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
ensure that your application meets with your specifications.
PIC32 logo, rfPIC and UNI/O are registered trademarks of
MICROCHIP MAKES NO REPRESENTATIONS OR
Microchip Technology Incorporated in the U.S.A. and other
WARRANTIES OF ANY KIND WHETHER EXPRESS OR countries.
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION, FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
INCLUDING BUT NOT LIMITED TO ITS CONDITION, MXDEV, MXLAB, SEEVAL and The Embedded Control
QUALITY, PERFORMANCE, MERCHANTABILITY OR Solutions Company are registered trademarks of Microchip
FITNESS FOR PURPOSE. Microchip disclaims all liability Technology Incorporated in the U.S.A.
arising from this information and its use. Use of Microchip Analog-for-the-Digital Age, Application Maestro, chipKIT,
devices in life support and/or safety applications is entirely at chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net,
the buyer’s risk, and the buyer agrees to defend, indemnify and dsPICworks, dsSPEAK, ECAN, ECONOMONITOR,
hold harmless Microchip from any and all damages, claims, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP,
suits, or expenses resulting from such use. No licenses are Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB,
conveyed, implicitly or otherwise, under any Microchip MPLINK, mTouch, Omniscient Code Generation, PICC,
intellectual property rights. PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE,
rfLAB, Select Mode, Total Endurance, TSHARC,
UniWinDriver, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2012, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.

ISBN: 978-1-62076-016-1

Microchip received ISO/TS-16949:2009 certification for its worldwide

headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.

 2012 Microchip Technology Inc. DS30509A-page 19

 Worldwide Sales and Service
AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE
Corporate Office Asia Pacific Office India - Bangalore Austria - Wels
2355 West Chandler Blvd. Suites 3707-14, 37th Floor Tel: 91-80-3090-4444 Tel: 43-7242-2244-39
Chandler, AZ 85224-6199 Tower 6, The Gateway Fax: 91-80-3090-4123 Fax: 43-7242-2244-393
Tel: 480-792-7200 Harbour City, Kowloon Denmark - Copenhagen
India - New Delhi
Fax: 480-792-7277 Hong Kong Tel: 45-4450-2828
Tel: 91-11-4160-8631
Technical Support: Tel: 852-2401-1200 Fax: 45-4485-2829
Fax: 91-11-4160-8632
http://www.microchip.com/ Fax: 852-2401-3431
India - Pune France - Paris
support
Australia - Sydney Tel: 91-20-2566-1512 Tel: 33-1-69-53-63-20
Web Address:
Tel: 61-2-9868-6733 Fax: 91-20-2566-1513 Fax: 33-1-69-30-90-79
www.microchip.com
Fax: 61-2-9868-6755 Germany - Munich
Atlanta Japan - Osaka
China - Beijing Tel: 49-89-627-144-0
Duluth, GA Tel: 81-66-152-7160
Tel: 86-10-8569-7000 Fax: 49-89-627-144-44
Tel: 678-957-9614 Fax: 81-66-152-9310
Fax: 86-10-8528-2104 Italy - Milan
Fax: 678-957-1455 Japan - Yokohama
China - Chengdu Tel: 39-0331-742611
Boston Tel: 81-45-471- 6166
Tel: 86-28-8665-5511 Fax: 39-0331-466781
Westborough, MA Fax: 81-45-471-6122
Fax: 86-28-8665-7889 Netherlands - Drunen
Tel: 774-760-0087 Korea - Daegu
Fax: 774-760-0088 China - Chongqing Tel: 82-53-744-4301 Tel: 31-416-690399
Tel: 86-23-8980-9588 Fax: 82-53-744-4302 Fax: 31-416-690340
Chicago
Itasca, IL Fax: 86-23-8980-9500 Spain - Madrid
Korea - Seoul
Tel: 630-285-0071 China - Hangzhou Tel: 34-91-708-08-90
Tel: 82-2-554-7200
Fax: 630-285-0075 Tel: 86-571-2819-3187 Fax: 82-2-558-5932 or Fax: 34-91-708-08-91
Cleveland Fax: 86-571-2819-3189 82-2-558-5934 UK - Wokingham
Independence, OH China - Hong Kong SAR Tel: 44-118-921-5869
Malaysia - Kuala Lumpur
Tel: 216-447-0464 Tel: 852-2401-1200 Fax: 44-118-921-5820
Tel: 60-3-6201-9857
Fax: 216-447-0643 Fax: 852-2401-3431 Fax: 60-3-6201-9859
Dallas China - Nanjing Malaysia - Penang
Addison, TX Tel: 86-25-8473-2460 Tel: 60-4-227-8870
Tel: 972-818-7423 Fax: 86-25-8473-2470 Fax: 60-4-227-4068
Fax: 972-818-2924
China - Qingdao Philippines - Manila
Detroit Tel: 86-532-8502-7355 Tel: 63-2-634-9065
Farmington Hills, MI
Fax: 86-532-8502-7205 Fax: 63-2-634-9069
Tel: 248-538-2250
Fax: 248-538-2260 China - Shanghai Singapore
Tel: 86-21-5407-5533 Tel: 65-6334-8870
Indianapolis Fax: 86-21-5407-5066 Fax: 65-6334-8850
Noblesville, IN
Tel: 317-773-8323 China - Shenyang Taiwan - Hsin Chu
Fax: 317-773-5453 Tel: 86-24-2334-2829 Tel: 886-3-5778-366
Fax: 86-24-2334-2393 Fax: 886-3-5770-955
Los Angeles
Mission Viejo, CA China - Shenzhen Taiwan - Kaohsiung
Tel: 949-462-9523 Tel: 86-755-8203-2660 Tel: 886-7-536-4818
Fax: 949-462-9608 Fax: 86-755-8203-1760 Fax: 886-7-330-9305
Santa Clara China - Wuhan Taiwan - Taipei
Santa Clara, CA Tel: 86-27-5980-5300 Tel: 886-2-2500-6610
Tel: 408-961-6444 Fax: 86-27-5980-5118 Fax: 886-2-2508-0102
Fax: 408-961-6445 China - Xian Thailand - Bangkok
Toronto Tel: 86-29-8833-7252 Tel: 66-2-694-1351
Mississauga, Ontario, Fax: 86-29-8833-7256 Fax: 66-2-694-1350
Canada China - Xiamen
Tel: 905-673-0699 Tel: 86-592-2388138
Fax: 905-673-6509 Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
11/29/11
Fax: 86-756-3210049

DS30509A-page 20  2012 Microchip Technology Inc.