CODE SN113-0005-00
DATE 2017.01.01
SPECIFICATION
MODEL : HYD. CRAWLER
DRILL
(JD – 1300E)
CUSTOMER :
JD – 1300E SN113-0005-00
1. General Description
JUNJIN CSM hydraulic crawler drill is a drilling machine for blasting with
dynamite in the quarries, and mining and construction site. It is mainly
composed of Traveling device as a base machine, Drifter, Guide shell, loading
device as drilling device, power unit and running device operated by diesel
engine. Differently from pneumatic drill, Air compressor and dust collector
installed on the power unit make a high efficient rock drilling with low noise as
much as possible.
2. Design assembly
FUEL TANK
1
www.junjincsm.com
JD – 1300E SN113-0005-00
2
www.junjincsm.com
JD – 1300E SN113-0005-00
3
www.junjincsm.com
JD – 1300E SN113-0005-00
4. Features
1) Powerful Drifter JET-9
Drifter model JET-9 with hydraulic hammering system and hydraulic motor
easily and speedily performs Drilling Φ 76~Φ 127 by hammering, rotating
and flushing the debris in the hole. Its simple and practical components are
different from the others.
① Special seals adopted in the front and rear of the piston enhance its
durability.
② Highly increased hammering energy increased drilling speed.
③ Chuck made of special alloy increases durability.
2) Working safety
① Tumbler length 2480mm and shoe width 330mm maximizes safety.
② Ground clearance (510mm) and track oscillation (±10°)on either side
prevent the bottom from being damaged by projection on the rough
zone.
3) Anti-jamming system
Makes the stable operation possible on all kind of rock and makes an
easy operations by an unskilled operator. This will be operated only in
case the anti-jamming switch is on position.
4) Collaring
Collaring makes it easy to take a correct position for drilling and an
unskilled operator performs drilling correctly.
5) Traveling speed and gradeability
The piston pump and traveling motor with high efficiency maximize its
traveling speed and gradeability-Traveling speed : 3.3km/h ;
Max. Grade ability: 28°
4
www.junjincsm.com
JD – 1300E SN113-0005-00
6) Maintenance and inspection
Panel typed bonnet and vertical typed fuel tank make more room for
checking and services.
The oil drain cocks installed on either side for engine oil, gear box oil, fuel,
compressor oil make the oil exchange and cleaning easy.
7) Powerful Dust Collector
① Dust collector with 4 filters prevents dust from flying in drilling and its
filters are protected by air flushing in each filter.
② To prevent the filter from being damaged by a water vein, shutter
installed within stop collecting dust in case a water vein appears
during drilling.
8) Comfortable and safe Cabin
Strong frame, safety glass on all directions, and safety net protect the
operator and provide secure broad view in job site. Floating typed operators
seat with air-bellows protects the operator from vibration and provides very
comfortable working conditions. Air condition, radio, and the heater are
provided as basic specifications.
9) Sliding Suction Hood
With suction hood cab slided up and down by the operator in the cabin, the
operator con performs drilling without others assistance correctly.
The hood stuck to the ground prevents the debris from flying in drilling.
10) Auto Lubrication for Drifter
Lubricator part and an oil tank are installed to refuel the Drifter Front Part
(gear box). The flow rate of the Lubricator has automatically supplied from an
oil tank.
The automatic lubrication system removes the inconvenience of feeding oil
frequently and protects the drifter from being damaged by lubrication oil
shortage.
5
www.junjincsm.com
JD – 1300E SN113-0005-00
11) Centralized Electric Control System
All the electric control devices are centralized in the control box for checking
any trouble easily.
12) Pre-Cleaner (Cyclone)-Optional Parts
Pre-cleaner installed between hood and dust collector protects the filters in
the dust collector and the hose from being damaged by the debris.
13) Auto Grease System
Before the rod and the sleeve connected, greases the external screw by only
pushing the button, which helps the rod and the sleeve charged tightly to get
easily loosed.
14) Auto Rod Changer (ARC)
The operator connects or disconnects the rods by controlling only a few
levers in the cabin without an assistant.
This automatic rod exchange can be performed by means of sequential
hydraulic schematic.
7 Rods(including the first rod) can be equipped in the cartridge of ARC
15) Cummins Engine with large output
Cummins engine with water cooling system supply sufficient power for
traveling or operating at job site. Especially its world wide services network
by Cummins will be a good point for the users.
16) Large Fuel Tank
Fuel tank can hold 405 liters and gives comparatively a long operating
duration.
The residual fuel can be observed in sight unless engine room opened.
6
www.junjincsm.com
JD – 1300E SN113-0005-00
17) Compressor On/Off Switch
Air compressor can be used only in case compressed air required by
On/Off switch. The On/Off switch of compressor is effective to cut down the
engine fuel consumption by unloading the compressor at the Off position.
7
www.junjincsm.com
JD – 1300E SN113-0005-00
5. Specifications
MODEL
NO ITEM
JD-1300E
Gross weight kg 14,700
Overall length mm 9,400
Overall
1 Overall width mm 2,420(2,890)
Dimensions
Overall height mm 2,940
Ground clearance mm 510
Hole range mm Φ 76~Φ 115
Performanc
2 Gradeabillity ° 28
e
Traveling speed km/h 0 ~ 3.3
Model CTAA8.3-C (CUMMINS)
3 Engine Rated output ps/rpm 205 / 2,200
Oscillating Angle ° ±10
Model JET-9 YH-80
Total Length Mm 1,148 1,025
Total Width Mm 379 360
Total Height Mm 297 295
Weight Kgf 270 210
4 Drifter Impact Frequency Hz 35~50 40~45
Rotational Torque Kgf-m Max. 88 Max. 59
Rotational Frequency RPM Max. 180 Max. 150
Impact Pressure Bar Max. 150 Max. 140
Rotation Pressure Bar Max. 140 Max. 140
Flusing Pressure Bar Max. 10.5 Max. 10.5
2
Working pressure kg/cm 10.5
Free air delivery m3 7.8
Tank capacity m3 0.051
Overall length mm 7,290
Slide length mm 1,500
6 Guide Feed length mm 4,300
Swing angle R/L。 30 /90
Tilt angle 。 180
8
www.junjincsm.com
JD – 1300E SN113-0005-00
MODEL
NO ITEM
JD-1300E
Overall length mm 3,000
Lift angle U/D。 50/25
7 Boom
Swing angle R/L。 35/25
Slide length mm 1,100
Suction capacity m3/min 20
Dust
8 Number of filters EA 4
collector
Blow pressure mm/Aq 600
Under Length of tumbler mm 2,480
9
carriage Shoe width mm 330
Length of rod mm 3,660
10 Tool Bit dia. mm Φ 76~Φ 115
Rod section mm T45, T51(*)
Variable piston pump
11 Hyd. sys. Hyd. pump
+ Gear pump
Auto rod Type ○
12
changer Number of Rod EA 6 + 1 (*5+1)
13 CABIN ROPS & FOPS STD
9
www.junjincsm.com
JD – 1300E SN113-0005-00
6. Specification Diagram
10
www.junjincsm.com
JD – 1300E SN113-0005-00
JD-1300E MAIN PARTS 1/3
DRIFTER
MODEL : JET-9
MAKER : JUNJIN CSM (KOREA)
11
www.junjincsm.com
JD – 1300E SN113-0005-00
JD-1300E MAIN PARTS
TRAVEL MOTOR
MODEL : TM18VC-A-80
TONGMYUNG HEAVY INDERSTRIES CO.LTD
LINK ASS’ Y
1. LINK
MODEL : P154x45 LINK
MAKER : HANBACK PRECISION COMPANY (KOREA)
2. SHOE PLATE
MODEL : SINGLE
MAKER : INTERTRACK (GERMANY)
12
www.junjincsm.com
JD – 1300E SN113-0005-00
JD-1300E MAIN PARTS
13
www.junjincsm.com
