BA-200

The recommendations made here are intended to be a guideline

for the selection of the suitable gasket quality Because the function
and durability of the products depend upon a number of factors,
the data may not be used to support any warranty claims

Recommended
Recommendation depends on operating conditions
Not recommended

Acetamide Ethyl acetate Oleum

Acetic acid 10% Ethyl alcohol Oxalic acid
Acetic acid 100% Ethyl chloride Oxygen
Acetic ester Ethylene Palmitic acid
Acetone Ethylene glycol Pentane
Acetylene Formic acid 10% Perchloroethylene
Adipic acid Formic acid 85% Phenol
Air Formaldehyde Phosphoric acid
Alum Freon 12 Potassium acetate
Aluminium acetate Freon 22 Potassium bicarbonate
Aluminium chlorate Fuel oil Potassium carbonate
Aluminium chloride Gasoline Potassium chloride
Ammonia Glycerine Potassium dichromate
Ammonium bicarbonate Heptane Potassium hydroxide
Ammonium chloride Hydraulic oil (Mineral) Potassium iodide
Ammonium hydroxide Hydraulic oil (phosphate esther type) Potassium nitrate
Amyl acetate Hydraulic oil (glycol based) Potassium permanganate
Aniline Hydrazine Propane
Asphalt Hydrochloric acid 20% Pyridine
Barium chloride Hydrochloric acid 36% Salicylic acid
Benzene Hydrofluoric acid 10% Silicone oil
Benzoic acid Hydrofluoric acid 40% Soap
Boric acid Hydrogen Sodium aluminate
Borax Isobutane Sodium bicarbonate
Butane Isooctane Sodium bisulphite
Butyl alcohol Isopropyl alcohol Sodium carbonate
Butyric acid Kerosene Sodium chloride
Calcium chloride Lead acetate Sodium cyanide
Calcium hydroxide Lead arsenate Sodium hydroxide
Carbon disulphide Magnesium sulphate Sodium sulphate
Carbon dioxide Malic acid Sodium sulphide
Chloroform Methane Starch
Chlorine, dry Methanol Steam
Chlorine, wet Methyl chloride Stearic acid
Chromic acid Methylene dichloride Sugar
Citric acid Methyl ethyl ketone Sulphuric acid 20%
Copper acetate Milk Sulphuric acid 96%
Creosote Mineral oil type ASTM no.1 Tar
Cresol Naphtha Tartaric acid
Cyclohexanol Nitric acid 20% Toluene
Cyclohexanone Nitric acid 40% Transformer oil
Decaline Nitric acid 96% Trichlorethylene
Dibenzyl ether Nitrobenzene Water
Dimethyl formamide Nitrogen White Spirit
Dowtherm Octane Xylene
angleški jezik, 050209

Ethane Oleic acid

In order to spread the most comprehensive knowledge of

our products, our highly skilled group of experts organized DONIT TESNIT d.d.
Cesta komandanta Staneta 38
in the technical-service department can assist you by solving 1215 MEDVODE, Slovenija
telefon: +386 (01) 582 32 00
practically any sealing problem. If you need our help, fax: +386 (01) 582 32 06, 582 32 08
E-mail: [email protected]
contact us. http://www.donittesnit.si
 BA-200
TECHNICAL DATA SHEET

Basis
Organic fibres, NBR
General properties and application
Oil resistant gasket material for low loadings. Very suitable for sealing of water, gases, oils and fuels.
Dimensions of standard sheets
Sheet size: 1000 x 1500 mm, 1500 x 1500 mm, 3000 x 1500 mm, 4500 x 1500 mm,
(other size on request)
Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm (other thicknesses on request)
Tolerances: Thickness: < 1 mm ± 0.1 mm, ³ 1 mm ± 10 %, Length: ± 50 mm, Width: ± 50
Surface treatment: Treatment with graphite, PTFE and antistick coating is available on request.

Technical data
Typical values (thickness 2.0 mm)
Compressibility ASTM F 36/J 8%
Recovery ASTM F 36/J 50 %
Tensile strenght DIN 52910 Min 6 MPa
Stress resistance DIN 52913
 16h, 300°C, 50 MPa
 16h, 175°C, 50 MPa 20 MPa
Specific Leak rate DIN 3535/6 Min 0.08 mg/(s.m)
Thickness increase ASTM F 146
 Oil IRM 903, 5h, 150°C 10 %
 ASTM Fuel B, 5h, 23°C 10 %
*Max. operating conditions
Peak temperature 180°C / 356°F
Continuous temperature 140°C / 285°F
- with steam 120°C / 248°F
Pressure 40 bar / 580 psi
* Temperature and pressure represent maximum values and should not be used simultaneously. They are given only
for guidance, since they depend not only on the type of gasket material but also on the assembly conditions. Very
important factors are: thickness of material, nature of service medium, type of flange, surface stress. Steam
application requires special consideration.
BA-200, 2 mm
EN 1514-1, Type IBC, PN 40/DIN 28091-2, 3.8
50
General suitability using common installation
practices under the condition of chemical
[bar]

40
compatibility.
Max. performance is ensure through 30
P R E S S U R E

appropriate measures for joint design and

gasket installation. Consultation is 20

recommended.
10
Limited application area - Technical
consultation is mandatory. 0
0 50 100 150 200
T E M P E R A T U R E [°C]

This edition cancels all previous issues. Subject to change without notice.