Scribd
Upload
45 views

Steel Grade: Material Data Sheet

The document provides information about the steel grade 41Cr4, including its chemical composition, mechanical properties, heat treatment recommendations, and other technical specifications. 41Cr4 is a steel suitable for quenching and tempering with a minimum hardness of 52 HRC that can be induction surface hardened. It through hardens in oil up to approximately 40mm in diameter.

Uploaded by

Hasan Ash
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
45 views

Steel Grade: Material Data Sheet

The document provides information about the steel grade 41Cr4, including its chemical composition, mechanical properties, heat treatment recommendations, and other technical specifications. 41Cr4 is a steel suitable for quenching and tempering with a minimum hardness of 52 HRC that can be induction surface hardened. It through hardens in oil up to approximately 40mm in diameter.

Uploaded by

Hasan Ash
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Material data sheet Last revised: Thu, 01 Oct 2020 13:01:11 GMT

Steel grade

41Cr4 All

General Information

41Cr4 is a steel for quenching and tempering recommended for components with strength requirements lower than
the steel 42CrMo4. It is suitable for induction surface hardening, min hardness 52 HRC. It through hardens in oil up
to appr. 40 mm diameter.

For additional Heat Treatment Data, please visit the Heat Treatment Guide

Similar designations
41CrS4, SS2245, 530M40, 530H40, EN18, SCR440, 42C4, 1.7035, 1.7039

Chemical composition
Variant Cast Di C% Si % Mn % P% S% Cr %
Min 0.38 - 0.60 - 0.020 0.90
5515 CC 4.4
Max 0.45 0.40 0.90 0.025 0.035 1.20
Mechanical Properties
Dimension Yield strength Tensile Elongation Reduction of area Impact (ISO-V)
Variant Condition Format Hardness
[mm] min [MPa] strength [MPa] A5 [%] Zmin [%] strengthmin
Round
+A 20 < 160 - - - - < 241 HB -
bar
Round 20 °C 35 J
5515 20 < 40 660* 900-1100 12 35 -
bar (long)
+QT
Round 20 °C 35 J
40.1 < 100 560* 800-950 14 40 -
bar (long)
Rp0.2 * Reh, ** Rel

Transformation temperatures
Temperature °C
MS 320
AC1 735
AC3 790

Heat treatment recommendations


Treatment Condition Temperature cycle Cooling/quenching
670- 710oC In air
Soft annealing +A

Austenizing 830 - 860oC


Water or oil
Quench & Tempering +QT
Tempering 540 - 680oC
Other properties (typical values)
Youngs module (GPa) Poisson´s ratio (-) Shear module (GPa) Density (kg/m3)
210 0.3 80 7800
Average CTE 20-300°C Specific heat Thermal conductivity Ambient Electrical resistivityAmbient
(µm/m°K) capacity 50/100°C (J/kg°K) temperature (W/m°K) temperature (µΩm)
12 460 - 480 40 - 45 0.20 - 0.25

Contact us
Would you like to know more about our offers? Don´t hesitate to contact us:

Via e-mail: [email protected]

Via telephone: +46 8 622 1300

For more detailed information please visit http://www.ovako.com/en/Contact-Ovako/

Disclaimer
The information in this document is for illustrative purposes only. The data and examples are only general recommendations and not a
warranty or a guarantee. The suitability of a product for a specific application can be confirmed only by Ovako once given the actual
conditions.The purchaser of an Ovako product has the responsibility to ascertain and control the applicability of the products before
using them. Continuous development may necessitate changes in technical data without notice. This document is only valid for Ovako
material. Other material, covering the same international specifications, does not necessarily comply with the properties presented in
this document.

You might also like