Procedure

Step 1 Configure LAG for upstream ports.

Configure upstream ports 0/19/0 and 0/19/1 into an aggregation group. Each member port in the aggregation group
allocates packets based on the source MAC address. The working mode is LACP static aggregation.

huawei(config)#link-aggregation 0/19 0-1 ingress workmode lacp-static

Step 2 Configure GPON ONT profiles.

1. Configure a DBA profile.

Create the same DBA profile for different types of services. Set the profile name to

ftth_dba, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth

to 20 Mbit/s.

huawei(config)#dba-profile add profile-name ftth_dba type3 assure 8192 max 20480

2. Configure an ONT line profile.

Create a GPON ONT line profile, named ftth, and bind it to the DBA profile ftth_dba.

huawei(config)#ont-lineprofile gpon profile-name ftth

huawei(config-gpon-lineprofile-1)#tcont 4 dba-profile-name ftth_dba

huawei(config-gpon-lineprofile-1)#gem add 11 eth tcont 4

huawei(config-gpon-lineprofile-1)#gem add 12 eth tcont 4

huawei(config-gpon-lineprofile-1)#gem add 13 eth tcont 4

huawei(config-gpon-lineprofile-1)#gem add 14 eth tcont 4

huawei(config-gpon-lineprofile-1)#commit

huawei(config-gpon-lineprofile-1)#quit

3. Configure an ONT service profile.

Create a GPON ONT service profile, named ftth. Configure the capability set of the ETH

port and POTS port to adaptive. Then the system automatically adapts to the ONT

according to the actual capability of the online ONT.

huawei(config)#ont-srvprofile gpon profile-name ftth

huawei(config-gpon-srvprofile-1)#ont-port eth adaptive pots adaptive

huawei(config-gpon-srvprofile-1)#commit

huawei(config-gpon-srvprofile-1)#quit

4. (Optional) Add an alarm profile. In this example, the default alarm profile is used, and
therefore the configuration of the alarm profile is not required.

Step 3 Add ONTs.

Connect two ONTs to GPON port 0/1/0. Set the ONT IDs to 1 and 2, SNs to

32303131D659FD40 and 6877687714852901, passwords to 0100000001 and 0100000002, discovery mode for
password authentication to once-on, and management mode to OMCI. Bind the two ONTs to ONT line profile ftth
and ONT service profile ftth.

There are two methods of adding an ONT: add an ONT offline and confirm an automatically discovered ONT.

  Add ONTs offline.

If the password of an ONT is known, run the ont add command to add an ONT offline.

huawei(config)#interface gpon 0/1

huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging

omci ont-lineprofile-name

ftth ont-srvprofile-name ftth

huawei(config-if-gpon-0/1)#ont add 0 2 password-auth 0100000002 once-on no-aging

omci ont-lineprofile-name

ftth ont-srvprofile-name ftth

  Confirm automatically discovered ONTs

If the password or SN of an ONT is unknown, run the port portid ont-auto-find command

in GPON mode to enable the ONT auto-discovery function of the GPON port. Then, run the ont confirm
command to confirm the ONT.

huawei(config)#interface gpon 0/1

huawei(config-if-gpon-0/1)#port 0 ont-auto-find enable

huawei(config-if-gpon-0/1)#display ont autofind 0

//After this command is executed, the information about all ONTs connected to

the GPON port through optical splitters is displayed.

huawei(config-if-gpon-0/1)#ont confirm 0 ontid 1 sn-auth 32303131D659FD40 omci

ont-lineprofile-name

ftth ont-srvprofile-name ftth

huawei(config-if-gpon-0/1)#ont confirm 0 ontid 2 sn-auth 6877687714852901 omci

ont-lineprofile-name

ftth ont-srvprofile-name ftth

NOTE
If multiple ONTs of the same type bound to the same line profile or service profile are connected to the same port,
you can bulk add ONTs by bulk confirming automatically discovered ONTs to make configuration easier and more
efficient. To do so, the preceding command can be modified as follows:

huawei(config-if-gpon-0/1)#ont confirm 0 all sn-auth omci ont-lineprofile-name

ftth ont-srvprofile-name ftth

 (Optional) Bind the alarm profile to the ONT.

The default profile 1 is used in this example.

huawei(config-if-gpon-0/1)#ont alarm-profile 0 1 profile-id 1

huawei(config-if-gpon-0/1)#ont alarm-profile 0 2 profile-id 1

Step 4 Check ONT status.

After an ONT is added, run the display ont info command to query the current status of the ONT. Ensure that
Config flag of the ONT is active, Run State is online, Config state is normal, and Match state is match.

huawei(config-if-gpon-0/1)#display ont info 0 1

———————————————————————

F/S/P : 0/1/0

ONT-ID : 1

Control flag : active //Indicates that the ONT is

activated.

Run state : online //Indicates that the ONT goes online

successfully.

Config state : normal //Indicates that the configuration state of the

ONT is normal.

Match state : match //Indicates that the capability profile bound to

the ONT is consistent with the actual capability of the ONT.

…//The rest of the response information is omitted.

When Config state is failed, Run state is offline, or Match state is mismatch:

 If Control flag is deactive, run the ont active command in GPON mode to activate the ONU.

 If Run state is offline, a physical line may be broken or the optical module may be damaged.

Check the line and the optical module.

 If Config state is failed, the configured ONU capability exceeds the actual ONU capability.

In this case, run the display ont failed-configuration command in the diagnose mode to

check the failed configuration item and the failure cause. Then, rectify the fault accordingly.

   If the ONU does not match, that is, Match state is mismatch, the port types and number of ports
undermatch the actual port types and number of ports supported by the ONU. In this case, run the display
 ont capability command to query the actual capability of the ONU, and then select one of the following
modes to modify the ONU configuration:

– Create a proper ONU profile according to the actual capability of the ONU, and then run

the ont modify command to modify the configuration data of the ONU.

– Modify the ONU profile according to the actual capability of the ONU and save the

modification. Then, the ONU automatically recovers the configuration successfully.

Step 5 Configure the traffic profile for the HSI service.

huawei(config)#traffic table ip name ftth_hsi cir 4096 priority 0 priority-policy

local-setting

Step 6 Configure the service port for the HSI service.

Table 1  Scenario plan

 Scenario 1:

Configure the mapping between a GEM port and a VLAN. The service flow of C-VLAN

1001 is mapped to GEM port 14 in the ONT line profile.

huawei(config)#ont-lineprofile gpon profile-name ftth

huawei(config-gpon-lineprofile-1)#gem mapping 14 0 vlan 1001

huawei(config-gpon-lineprofile-1)#commit

huawei(config-gpon-lineprofile-1)#quit

Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the PC

through Ethernet port 1, add Ethernet port 1 to VLAN 1001 in the ONT service profile.

huawei(config)#ont-srvprofile gpon profile-name ftth

huawei(config-gpon-srvprofile-1)#port vlan eth 1 1001

huawei(config-gpon-srvprofile-1)#commit

huawei(config-gpon-srvprofile-1)#quit

Configure the native VLAN of the ONT port. Set the native VLAN ID of Ethernet port 1 to 1001.

huawei(config)#interface gpon 0/1

huawei(config-if-gpon-0/1)#ont port native-vlan 0 1 eth 1 vlan 1001

huawei(config-if-gpon-0/1)#ont port native-vlan 0 2 eth 1 vlan 1001

huawei(config-if-gpon-0/1)#quit

Create an Internet access service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 100.

huawei(config)#vlan 100 smart

huawei(config)#vlan attrib 100 stacking

huawei(config)#port vlan 100 0/19 0

Create service flows. Set the service VLAN to 100, GEM port ID to 14, and user VLAN to

1001. Use traffic profile ftth_hsi.

huawei(config)#service-port vlan 100 gpon 0/1/0 ont 1 gemport 14 multi-service

user-vlan 1001 tag-transform translate-and-add inner-vlan 1010 inbound traffic- table name ftth_hsi
outbound traffic-table name ftth_hsi

huawei(config)#service-port vlan 100 gpon 0/1/0 ont 2 gemport 14 multi-service

user-vlan 1001 tag-transform translate-and-add inner-vlan 1011 inbound traffictable

name ftth_hsi outbound traffic-table name ftth_hsi

 Scenario 2:

Configure the mapping between a GEM port and an Ethernet port on the ONT. Map the

service flow of Ethernet port 1 to GEM port 14 in the ONT line profile.

huawei(config)#ont-lineprofile gpon profile-name ftth

huawei(config-gpon-lineprofile-1)#mapping mode port

huawei(config-gpon-lineprofile-1)#gem mapping 14 0 eth 1

huawei(config-gpon-lineprofile-1)#commit

huawei(config-gpon-lineprofile-1)#quit

Configure the ONT packet processing mode. If the ONT is connected to the PC through

Ethernet port 1, In the ONT service profile, set the packet transmission mode to TAG

transparent transmission for Ethernet port 1.

huawei(config)#ont-srvprofile gpon profile-name ftth

huawei(config-gpon-srvprofile-1)#port vlan eth 1 transparent

huawei(config-gpon-srvprofile-1)#commit

huawei(config-gpon-srvprofile-1)#quit

Create an Internet access service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 100.

huawei(config)#vlan 100 smart

huawei(config)#vlan attrib 100 stacking

huawei(config)#port vlan 100 0/19 0

Create service flows. Set S-VLAN ID to 100 and GEM port ID to 14. Use traffic profile

ftth_hsi.

huawei(config)#service-port vlan 100 gpon 0/1/0 ont 1 gemport 14 multi-service

user-vlan untagged tag-transform add-double inner-vlan 1001 inbound traffictable

name ftth_hsi outbound traffic-table name ftth_hsi

huawei(config)#service-port vlan 100 gpon 0/1/0 ont 2 gemport 14 multi-service

user-vlan untagged tag-transform add-double inner-vlan 1002 inbound traffictable

name ftth_hsi outbound traffic-table name ftth_hsi

Step 7 Configure the traffic profile for the voice service.

huawei(config)#traffic table ip name ftth_voip cir off priority 5 priority-policy

local-setting

Step 8 Configure the VLAN translation policy and service flows for the voice service.

1. Perform this step in the bridging ONT (single VLAN tag) scenario.

Table 2  Data plan

Configure the mapping relationship between a GEM port and a VLAN. The service flow

of user VLAN 300 is mapped to GEM port 12 in the ONT line profile.

huawei(config)#ont-lineprofile gpon profile-name ftth

huawei(config-gpon-lineprofile-1)#gem mapping 12 2 vlan 300

huawei(config-gpon-lineprofile-1)#commit

huawei(config-gpon-lineprofile-1)#quit

Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN

300.

huawei(config)#vlan 300 smart

huawei(config)#port vlan 300 0/19 0

Create service flows. Set the service VLAN to 300, GEM port ID to 12, and user VLAN

to 300, and use traffic profile ftth_voip.

huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi-service

user-vlan 300 inbound traffic-table name ftth_voip outbound traffic-table

name ftth_voip

huawei(config)#service-port vlan 300 gpon 0/1/0 ont 2 gemport 12 multi-service

user-vlan 300 inbound traffic-table name ftth_voip outbound traffic-table

name ftth_voip

2. Perform this step in the bridging ONT (double VLAN tags) scenario.

Table 3 Data plan

Configure the mapping relationship between a GEM port and a VLAN. The service flow

of user VLAN 3001 is mapped to GEM port 12 in the ONT line profile.

huawei(config)#ont-lineprofile gpon profile-name ftth

huawei(config-gpon-lineprofile-1)#gem mapping 12 2 vlan 3001

huawei(config-gpon-lineprofile-1)#commit

huawei(config-gpon-lineprofile-1)#quit

Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN

300.

huawei(config)#vlan 300 smart

huawei(config)#vlan attrib 300 stacking

huawei(config)#port vlan 300 0/19 0

Create service flows. Set the service VLAN to 300, GEM port ID to 12, and user VLAN

to 3001, and use traffic profile ftth_voip.

huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multiservice

user-vlan 3001 tag-transform default inbound traffic-table name ftth_voip

outbound traffic-table name ftth_voip

huawei(config)#service-port vlan 300 gpon 0/1/0 ont 2 gemport 12 multiservice

user-vlan 3001 tag-transform default inbound traffic-table name ftth_voip

outbound traffic-table name ftth_voip

Step 9 Configure ONT voice service profiles.

ONT voice service profiles include the interface common profile, MGC interface profile, and POTS port profile.

  Interface common profile: saves common attributes of an ONT voice interface, including the fax mode,
fax/modem negotiation mode, and priority of the coding and decoding mode.

 MGC interface profile: saves the IP address or domain name of the MGC, protocol port ID of the MGC
transport layer to which the MG interface belongs, and DSCP priority of media packets.

 POTS port profile: saves physical attributes of a POTS port on an ONT, including the

impedance, transmitting gain, receiving gain, and signaling type of the POTS port.

1. Configure an interface common profile.

Run the display ont-mg-attribute-profile command to query the existing interface

common profile in the system. If the existing interface common profile in the system does

not meet the requirements, run the ont-mg-attribute-profile add command to add an

interface common profile.

In this example, the default interface common profile, namely interface common profile 1

is used.

2. Configure an MGC interface profile.

Run the display ont-mgc-profile command to query the existing MGC interface profile in

the system. If the existing MGC interface profile in the system does not meet the

requirements, run the ont-mgc-profile add command to add an MGC interface profile.

Create MGC interface profile 2, set the IP address of the MGC to 200.200.200.200, and

use default values for other parameters.

huawei(config)#ont-mgc-profile add profile-id 2 primary-mgc 200.200.200.200

3. Configure a POTS port profile.

Run the display ont-pots-profile command to query the existing POTS port profile in the

system. If the existing POTS port profile in the system does not meet the requirements, run the ont-pots-profile
add command to add a POTS port profile.

In this example, the default POTS port profile, namely POTS port profile 1 is used.

Step 10 Configure the IP addresses of ONT H.248 users.

For ONT 1 and ONT 2, configure the IP address obtaining mode to the dhcp mode, set the

management VLAN to VLAN 20, and use default values for other parameters.

huawei(config)#interface gpon 0/1

huawei(config-if-gpon-0/1)#ont ipconfig 0 1 dhcp vlan 20

huawei(config-if-gpon-0/1)#ont ipconfig 0 2 dhcp vlan 20

Step 11 Configure H.248 PSTN users.

1. Add an H.248 interface and apply an MGC interface profile to the interface.
For ONT 1 and ONT 2, set the MG ID to 1, apply MGC interface profile 2 to ONT 1 and

ONT 2, and use default values for other parameters.

If parameters of an MGC interface profile are changed, the MGC interface profile must be

reapplied to the ONT so that the changed parameters can take effect.

huawei(config-if-gpon-0/1)#if-h248 add 0 1 1 mgc-profile profile-id 2

huawei(config-if-gpon-0/1)#if-h248 add 0 2 1 mgc-profile profile-id 2

1. Add PSTN users.

For ONT 1 and ONT 2, create a PSTN user, set the MG ID to 1 (identical to the MG ID of

the H.248 interface), and set the physical terminal port ID to A0 and A1.

huawei(config-if-gpon-0/1)#mgpstnuser add 0 1 1 mgid 1 terminalid A0

huawei(config-if-gpon-0/1)#mgpstnuser add 0 2 1 mgid 1 terminalid A1

Run the display mgpstnuser attribute command to check whether the configuration of

the PSTN user is properly set.

huawei(config-if-gpon-0/1)#display mgpstnuser attribute 0 1 1

——————————————————————————

F/S/P : 0/1/0

ONT ID : 1

Port ID : 1

MG ID : 1

Terminal ID : A0

…//The rest of the response information is omitted.

huawei(config-if-gpon-0/1)#display mgpstnuser attribute 0 2 1

——————————————————————————

F/S/P : 0/1/0

ONT ID : 2

Port ID : 1

MG ID : 1

Terminal ID : A1

…//The rest of the response information is omitted.

Step 12 Apply ONT voice service profiles

After ONT voice service profiles are applied, if parameters in those profiles are changed, those profiles must be
reapplied so that the changed parameters can take effect.
1. Apply an interface common profile.

Run the if-h248 attribute command to apply an interface common profile to an H.248

interface or configure the interface customized parameters, or run the ont-if-h248 batapply command to bulk
apply the interface common profiles to H.248 interfaces. If you

use these two commands to apply the interface common profiles or configure the interface

customized parameters repeatedly, the last configurations take effect.

In this example, the default interface common profile, namely interface common profile 1

is used.

2. Apply a POTS port profile.

Run the pstnport electric command to apply a POTS port profile to an H.248 interface or

configure the interface customized parameters, or run the ont-pstnport electric batapply

command to bulk apply the POTS port profiles to H.248 interfaces. If you use these

two commands to apply the POTS port profiles or configure the interface customized

parameters repeatedly, the last configurations take effect.

In this example, the default POTS port profile, namely POTS port profile 1 is used.

Step 13 (Optional) Configure the H.248 user codec.

Run the mgpstnuser codec command to configure the H.248 user codec. The H.248 user codec will not be
configured independently in this example.

Step 14 Configure the traffic profile for the IPTV service.

huawei(config)#traffic table ip index 8 cir off priority 4 priority-policy

local-setting

Step 15 Configure the VLAN translation policy and service port for the multicast service.

Configure the mapping relationship between a GEM port and an Ethernet port on the ONT. If the ONT is
connected to the STB through Ethernet port 2, map the service flow of Ethernet port 2 to GEM port 13 in the ONT
line profile.

huawei(config)#ont-lineprofile gpon profile-name ftth

huawei(config-gpon-lineprofile-1)#mapping mode port

huawei(config-gpon-lineprofile-1)#gem mapping 13 1 eth 2

huawei(config-gpon-lineprofile-1)#commit

huawei(config-gpon-lineprofile-1)#quit

Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the STB

through Ethernet port 2, add Ethernet port 2 to VLAN 1000.

huawei(config)#ont-srvprofile gpon profile-name ftth

huawei(config-gpon-srvprofile-1)#port vlan eth 2 1000

huawei(config-gpon-srvprofile-1)#multicast-forward untag

huawei(config-gpon-srvprofile-1)#commit

huawei(config-gpon-srvprofile-1)#quit

Configure the native VLAN of the ONT port. If the ONT is connected to the STB through

Ethernet port 2, the native VLAN ID is 1000.

huawei(config)#interface gpon 0/1

huawei(config-if-gpon-0/1)#ont port native-vlan 0 1 eth 2 vlan 1000

huawei(config-if-gpon-0/1)#ont port native-vlan 0 2 eth 2 vlan 1000

huawei(config-if-gpon-0/1)#quit

Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 1000.

huawei(config)#vlan 1000 smart

huawei(config)#port vlan 1000 0/19 0

Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to

untagged, and use traffic profile 8.

huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi-service

user-vlan untagged rx-cttr 8 tx-cttr 8

huawei(config)#service-port 2 vlan 1000 gpon 0/1/0 ont 2 gemport 13 multi-service

user-vlan untagged rx-cttr 8 tx-cttr 8

Step 16 Create an MVLAN and configure the IGMP version.

Set the IGMP version for the MVLAN to IGMP IPv6 v2.

huawei(config)#multicast-vlan 1000

huawei(config-mvlan1000)#igmp ipv6 version v2

This operation will delete all IPv6 programs with source IP addresses in the

current multicast VLAN

Are you sure to change current IGMP IPv6 version? (y/n)[n]:y

Command is being executed. Please wait…

Command has been executed successfully

Step 17 Configure a program library.

Set the mode for obtaining multicast programs to dynamic.

NOTE

You can set the mode for obtaining multicast programs to dynamic only when the IGMP mode is off.

huawei(config-mvlan1000)#igmp ipv6 mode off

Are you sure to close IGMP IPv6? (y/n)[n]:y

Command is being executed. Please wait…

Command has been executed successfully

huawei(config-mvlan1000)#igmp ipv6 match mode disable

Command has been executed successfully

(Optional) Set the address range for the dynamic programs. If you need to limit the address range of dynamic
programs, perform this operation. For example, set the address range of dynamic programs to ff15::-ff15::ffff.

huawei(config-mvlan1000)#igmp ipv6 match group ipv6 ff15:: to-ipv6 ff15::ffff

Step 18 Set the IGMP IPv6 mode.

Select the IGMP IPv6 proxy mode.

huawei(config-mvlan1000)#igmp ipv6 mode proxy

Are you sure to change IGMP IPv6 mode? (y/n)[n]:y

Command is being executed. Please wait…

Command has been executed successfully

Step 19 Configure the IGMP upstream port.

Set the IGMP upstream port ID to 0/19/0 and working mode to default. Protocol packets are transmitted to all the
IGMP upstream ports in the multicast VLAN.

huawei(config-mvlan1000)#igmp uplink-port 0/19/0

huawei(config-mvlan1000)#btv

huawei(config-btv)#igmp uplink-port-mode default

Are you sure to change the uplink port mode?(y/n)[n]:y

Step 20 Configure multicast users.

Add service ports 1 and 2 as multicast users.

huawei(config-btv)#igmp policy service-port 1 normal

huawei(config-btv)#igmp policy service-port 2 normal

huawei(config-btv)#igmp user add service-port 1

huawei(config-btv)#igmp user add service-port 2

huawei(config-btv)#multicast-vlan 1000

huawei(config-mvlan1000)#igmp multicast-vlan member service-port 1

huawei(config-mvlan1000)#igmp multicast-vlan member service-port 2

huawei(config-mvlan1000)#quit

Step 21 Configure the traffic profile for the VoD service.

huawei(config)#traffic table ip index 8 cir off priority 4 priority-policy

local-setting

Step 22 Configure the VLAN translation policy and service port for the VoD service.

Configure the mapping relationship between a GEM port and a VLAN. The service flow of user VLAN 1100 is
mapped to GEM port 13 in the ONT line profile.

huawei(config)#ont-lineprofile gpon profile-name ftth

huawei(config-gpon-lineprofile-1)#gem mapping 13 4 vlan 1100

huawei(config-gpon-lineprofile-1)#commit

huawei(config-gpon-lineprofile-1)#quit

Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the STB

through Ethernet port 2, add Ethernet port 2 to VLAN 1100.

huawei(config)#ont-srvprofile gpon profile-name ftth

huawei(config-gpon-srvprofile-1)#port vlan eth 2 1100

huawei(config-gpon-srvprofile-1)#commit

huawei(config-gpon-srvprofile-1)#quit

Configure the native VLAN of the ONT port. If the ONT is connected to the STB through

Ethernet port 2, the native VLAN ID is 1100.

huawei(config-if-gpon-0/1)#ont port native-vlan 0 1 eth 2 vlan 1100

huawei(config-if-gpon-0/1)#ont port native-vlan 0 2 eth 2 vlan 1100

huawei(config-if-gpon-0/1)#quit

Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 1100.

huawei(config)#vlan 1100 smart

huawei(config)#port vlan 1100 0/19 0

 

Create service flows. Set the service VLAN to 1100, GEM port ID to 13, and VLAN translation mode to
transparent transmission, and use traffic profile 8.

huawei(config)#service-port 3 vlan 1100 gpon 0/1/0 ont 1 gemport 13 rx-cttr 8 txcttr

8 tag-transform transparent

huawei(config)#service-port 4 vlan 1100 gpon 0/1/0 ont 2 gemport 13 rx-cttr 8 txcttr

8 tag-transform transparent

Step 23 (Optional) Configure the PITP function for PPPoE.

huawei(config)#raio-mode common pitp-pmode

huawei(config)#pitp enable pmode

Step 24 (Optional) Configure the DHCP option function for IPoE.

huawei(config)#raio-mode common dhcp-option82 //For DHCPv4 packets

huawei(config)#dhcp option82 enable //For DHCPv4 packets

huawei(config)#raio-mode common dhcpv6-option //For DHCPv6 packets

huawei(config)#dhcpv6 option enable //For DHCPv6 packets

Step 25 Save the configuration on the OLT side.

huawei(config)#save