FC-28  2

[Technical Data]
Hexagon Socket Head Cap Screws Excerpts from JIS B 1176(1999, 2000)

1. Dimensions of Sections 2. L, s and g of Hexagon Socket Head Cap Screws Unit:mm

Nominal of Thread (d) M2 M2.5 M3 M4 M5 M6 M8 M10 M12 M14 M16 (M18) M20 (M22) M24 (M27) M30
To be chamfered.
May be roughed out when L ℓs min and ℓg max
t
w it is M4 or less. t Nominal ℓ ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg ℓs ℓg
w min max s
Bottom of Cone Length min max min max min max min max min max min max min max min max min max min max min max min max min max min max min max min max min max
120° (Min.) d
5 4.76 5.24

.)
(Min
Ødk
6 5.76 6.24
Øda
Øds
e

Incomplete Threaded Portion

120°
(2P or Less) 8 7.71 8.29
s ℓs Drill Bottom
10 9.71 10.29
Interior of hexagonal ℓg b(Reference)
hole may be chamfered. 12 11.65 12.35
k L
16 15.65 16.35
20 19.58 20.42 2 4
25 24.58 25.42 5.75 8 4.5 7
Rounded or Chamfered Radius Max. Rounding Beneath Neck 30 29.58 30.42 9.5 12 6.5 10 4 8
f(Max.)=1.7r(Max.)
v

Head f 35 34.5 35.5 11.5 15 9 13 6 11

r
Ødk

40 39.5 40.5 16.5 20 14 18 11 16 5.75 12

Ødw

da(Max.) – ds(Max.)

r
r(Max.)= 2 45 44.5 45.5 19 23 16 21 10.75 17 5.5 13
v
r

50 49.5 50.5 24 28 21 26 15.75 22 10.5 18

4 5° .) Chamfering
ax r(Min.)= Value in the Attached Table 55 54.4 55.6 26 31 20.75 27 15.5 23 10.25 19
(M

da
ds
60 59.4 60.6 31 36 25.75 32 20.5 28 15.25 24 10 20
65 64.4 65.6 30.75 37 25.5 33 20.25 29 15 25 11 21 4.5 17
Unit:mm
70 69.4 70.6 35.75 42 30.5 38 25.25 34 20 30 16 26 9.5 22
Nominal of Thread(d)(2) M2 M2.5 M3 M4 M5 M6 M8 M10 M12 (M14) M16 (M18) M20 (M22) M24 (M27) M30 80 79.4 80.6 45.75 52 40.5 48 35.25 44 30 40 26 36 19.5 32 15.5 28 11.5 24
Pitch of Thread(P) 0.4 0.45 0.5 0.7 0.8 1 1.25 1.5 1.75 2 2 2.5 2.5 2.5 3 3 3.5 90 89.3 90.7 50.5 58 45.25 54 40 50 36 46 29.5 42 25.5 38 21.5 34 15 30 9 24
b Reference 16 17 18 20 22 24 28 32 36 40 44 48 52 56 60 66 72 100 99.3 100.7 60.5 68 55.25 64 50 60 46 56 39.5 52 35.5 48 31.5 44 25 40 19 34
Max.(Basis)† 3.8 4.5 5.5 7 8.5 10 13 16 18 21 24 27 30 33 36 40 45 110 109.3 110.7 66.25 74 60 70 56 66 49.5 62 45.5 58 41.5 54 35 50 29 44 20.5 38
dk Max.†† 3.98 4.68 5.68 7.22 8.72 10.22 13.27 16.27 18.27 21.33 24.33 27.33 30.33 33.39 36.39 40.39 45.39 120 119.3 120.7 75.25 84 70 80 66 76 59.5 72 55.5 68 51.5 64 45 60 39 54 30.5 48
Min. 3.62 4.32 5.32 6.78 8.28 9.78 12.73 15.73 17.73 20.67 23.67 26.67 29.67 32.61 35.61 39.61 44.61 130 129.2 130.8 80 90 76 86 69.5 82 65.5 78 61.5 74 55 70 49 64 40.5 58
da Max. 2.6 3.1 3.6 4.7 5.7 6.8 9.2 11.2 13.7 15.7 17.7 20.2 22.4 24.4 26.4 30.4 33.4 140 139.2 140.8 90 100 86 96 79.5 92 75.5 88 71.5 84 65 80 59 74 50.5 68
Max.(Basis) 2 2.5 3 4 5 6 8 10 12 14 16 18 20 22 24 27 30 150 149.2 150.8 96 106 89.5 102 85.5 98 81.5 94 75 90 69 84 60.5 78
ds
Min. 1.86 2.36 2.86 3.82 4.82 5.82 7.78 9.78 11.73 13.73 15.73 17.73 19.67 21.67 23.67 26.67 29.67 160 159.2 160.8 106 116 99.5 112 95.5 108 91.5 104 85 100 79 94 70.5 88
e Min. 1.73 2.30 2.87 3.44 4.58 5.72 6.86 9.15 11.43 13.72 16.00 16.00 19.44 19.44 21.73 21.73 25.15 180 179.2 180.8 119.5 132 115.5 128 111.5 124 105 120 99 114 90.5 108
f Max. 0.51 0.51 0.51 0.60 0.60 0.68 1.02 1.02 1.45 1.45 1.45 1.87 2.04 2.04 2.04 2.89 2.89 200 199.05 200.95 135.5 148 131.5 144 125 140 119 134 110.5 128
Max.(Basis) 2 2.5 3 4 5 6 8 10 12 14 16 18 20 22 24 27 30 220 219.05 220.95 139 154 130.5 148
k
Min. 1.86 2.36 2.86 3.82 4.82 5.70 7.64 9.64 11.57 13.57 15.57 17.57 19.48 21.48 23.48 26.48 29.48 240 239.05 240.95 159 174 150.5 168
r Min. 0.1 0.1 0.1 0.2 0.2 0.25 0.4 0.4 0.6 0.6 0.6 0.6 0.8 0.8 0.8 1 1 260 258.95 261.05 179 194 170.5 188
Nominal(Basis) 1.5 2 2.5 3 4 5 6 8 10 12 14 14 17 17 19 19 22 280 278.95 281.05 199 214 190.5 208
Min. 1.52 2.02 2.52 3.02 4.02 5.02 6.02 8.025 10.025 12.032 14.032 14.032 17.05 17.050 19.065 19.065 22.065 300 298.95 301.05 219 234 210.5 228
s
Max. Column 1 1.560 2.060 2.580 3.080 4.095 5.140 6.140 8.175 10.175 12.212 14.212 14.212 17.230 17.230 19.275 19.275 22.275
(1) Column 2 1.545 2.045 2.560 3.080 4.095 5.095 6.095 8.115 10.115 12.142 14.142 14.142
t Min. 1 1.1 1.3 2 2.5 3 4 5 6 7 8 9 10 11 12 13.5 15.5 Reference:Dimensions of Counterboring and Bolt Hole for the Hexagon Socket Head Cap Screws
v Max. 0.2 0.25 0.3 0.4 0.5 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.7 3
dw Min. 3.40 4.18 5.07 6.53 8.03 9.38 12.33 15.33 17.23 20.17 23.17 25.87 28.87 31.81 34.81 38.61 43.61
Unit:mm
D' D' Nominal of Thread (d) M3 M4 M5 M6 M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30
w Min. 0.55 0.85 1.15 1.4 1.9 2.3 3.3 4 4.8 5.8 6.8 7.7 8.6 9.5 10.4 12.1 13.1
dk dk
Note ( 1 ) : Column 1 for s (max.) is applicable to strength class 8.8, 10.9, A 2-50 and A 2-70; Column 2 should be applied to strength class 12.9. ds 3 4 5 6 8 10 12 14 16 18 20 22 24 27 30
Column 1 may be applicable to strength class 12.9 in accordance with an agreement made between the delivering and receiving sides. d' 3.4 4.5 5.5 6.6 9 11 14 16 18 20 22 24 26 30 33

H'

H''
k

k
When the nominal of thread is M20 or larger, s (max.) should be applied to all strength classes ds ds dk 5.5 7 8.5 10 13 16 18 21 24 27 30 33 36 40 45
Note ( 2 ) : Nominal of thread in brackets should not be used unless it is absolutely necessary. d' d'
D' 6.5 8 9.5 11 14 17.5 20 23 26 29 32 35 39 43 48
Reference 1. A side of the head should be knurled into a straight line or crisscross pattern[ refer to JIS B 0951 (knurling pattern) ]dk(max.) should be the value d d k 3 4 5 6 8 10 12 14 16 18 20 22 24 27 30
marked with††.
d2 d2 H' 2.7 3.6 4.6 5.5 7.4 9.2 11 12.8 14.5 16.5 18.5 20.5 22.5 25 28
If no knurled pattern is needed, purchasers can indicate that. However, dk(max.)should be the value marked with†
2. Recommended nominal lengths(L)for individual nominal of thread are shown within the bold lines. H'' 3.3 4.4 5.4 6.5 8.6 10.8 13 15.2 17.5 19.5 21.5 23.5 25.5 29 32
If L is shorter than the dotted line, the thread should be fully threaded, and the incompletely threaded part length beneath the neck should be d2 2.6 3.4 4.3 5.1 6.9 8.6 10.4 12.2 14.2 15.7 17.7 19.7 21.2 24.2 26.7
approximately 3P.
3. ℓg(max.)and ℓg(min.)for a screw, whose length(L)exceeds the dotted line, are obtained by the equations below:
ℓg(Max)=Nominal Length(L)-b
ℓs(Min)=ℓg(Max)-5P

2847 2848

FC-28-1_E+.indd 2847-2848 08.4.23 10:27:11 AM