Using Williams Products

Readers of this catalog should independently verify the efficiency of any Williams products for the purpose intended
by the user. The suitability of Williams products will depend upon field conditions, fabrications and user specifications
which must be investigated and controlled by the user or its representatives. What follows are some suggestions for
proper use of Williams products.

Proper Use is the Key

Williams Form Engineering Corporation provides a limited warranty on all of its products, as set forth in its quota-
tions, acknowledgements and invoices furnished to each customer in connection with the sale of those products. Not
withstanding this limited warranty, you should be aware that Williams products are intended for use by qualified and
experienced workers. Serious accidents may result from misuse or improper supervision or inspection. Carefully field
test any use not strictly conforming to normal practice before general adoption of the application. Carefully evaluate the
product application, determine safe working loads and control all field conditions to prevent unsafe load applications. All
safety factors shown are approximate, and in no case should they be exceeded.
IMPROPER USE OR INSTALLATION MAY RESULT IN SERIOUS INJURY OR DEATH. IF YOU HAVE THE
SLIGHTEST DOUBT CONCERNING PROPER USE OR INSTALLATION, PLEASE CONSULT WITH OUR ENGI-
NEERING DEPARTMENT.

You are Responsible for Any Modifications or Substitutions

Do not weld any casting, unless in the opinion of a qualified engineer such weld is in a no load, non-critical area.
Welding causes carbides and extreme brittleness near the weld point, and destroys nearly all load value. Any welding
or modifications to Williams products are the responsibility of the user, and as set forth in its limited warranty, Williams
Form Engineering Corporation makes no representations or warranties concerning products altered, welded, bent or
modified by others.
Many Williams products are manufactured, supplied and or designed as a system. Hence, we cannot guarantee that
components from systems supplied by other manufacturers are interchangeable with our products. For best results, all
parts of a system should consist of Williams products. From time to time, Williams Form Engineering Corporation may
change product designs, safe working load ratings and product dimensions without prior notice to users. For the most
current information concerning Williams products, please contact our engineering department, one of our technical rep-
resentative or see our web site.

Ongoing Inspection and Replacement are Essential

Each user should periodically inspect bolts and working hardware for wear and discard worn parts. Bent bolts, and
bolts used at loads exceeding advertised yield strength should be discarded and replaced. A comprehensive inspection
and replacement program should be instituted and followed, so that all bolts will be replaced after a predetermined num-
ber of uses, regardless of the apparent condition of the bolt.
All lifting hardware units displayed in this catalog are subject to wear, misuse, overloading, corrosion, deformation
and other factors which may affect their safe working load. They should be regularly inspected to see if they may be
used at the rated safe working load or removed from service. Frequency of inspection is dependent upon frequency and
period of use, environment and other factors, and is best determined by an experienced user taking into account the
actual conditions under which the hardware is used.

Ordering Procedure and Warranties

This catalog is intended to provide potential purchasers and users with general information about products offered
by Williams Form Engineering Corporation. Prices, specifications, product descriptions and catalog items are subject to
modification without prior notice. Any person desiring further information about products offered by Williams Form
Engineering Corporation may contact the company or its authorized representatives. In appropriate cases, Williams will
provide quotations for possible orders.
Because the contents of this catalog are intended for general information purposes, they are subject to change with-
out notice. Any warranties for Williams products shall be governed by Williams quotations, acknowledgements and
invoices furnished to customers in connection with the sale of Williams products, as these documents contain more detail
than this catalog. Williams Form Engineering Corporation disclaims all other warranties for its products, expressed or
implied, including IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
which might otherwise arise from the contents of this catalog.
 Table of Contents
Using Williams Products . . . . . . . . . . . . . . . . . . . . . 2 Chapter 5: Other Mechanical Anchors
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Sledge Drive Anchor Information . . . . . . . . . . . . . . . 32
Chapter 1: Design Considerations Chapter 6: Epoxy Concrete Anchors
Different Types of Concrete Anchors . . . . . . . . . 4 & 5 Epoxy Anchor Information . . . . . . . . . . . . . . . . . . . . 33
F/;>:3
=4
B63
L
=<3
3A75<
#3B6=2








 Epoxy Anchor Technical Data . . . . . . . . . . . . . . . . . 34
Prestressed Anchors Defined . . . . . . . . . . . . . . . . . 8 Epoxy Anchor Strength Charts . . . . . . . . . . . . . . . . 35
Corrosion Protection. . . . . . . . . . . . . . . . . . . . . . . . . 9 Epoxy Anchor 3A75<
=<A723@/B7=<A












Epoxy Anchor <AB/::/B7=<





















Chapter 2: Spin-Lock Mechanical Anchors
Spin-Lock Information . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 7: Cast-in-Place Concrete Anchors
Spin-Lock Anchor Data . . . . . . . . . . . . . . . . . . 11 - 13 Cast-in-Place Information . . . . . . . . . . . . . . . . 38 & 39
Spin-Lock Design Considerations . . . . . . . . . . . 14 - 15
Chapter 8: Grout Bonded Concrete Anchors
(>7<"=19
3/2
AA3;0:73A



















Grout Bonded Information. . . . . . . . . . . . . . . . . . . . 40
(>7<"=19
<AB/::/B7=<
&@=132C@3A













Spin-Lock Project Photos . . . . . . . . . . . . . . . . . . . . 19 Chapter 9: Threaded Steel Bars & Accessories
Anchor Accessories . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 3: S-9 Undercut Concrete Anchors
150 KSI All-Thread-Bar . . . . . . . . . . . . . . . . . . 42 & 43
S-9 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
@/23

::)6@3/2
'30/@


















S-9 Anchor Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
%B63@
/@
113AA=@73A























S-9 Design Considerations . . . . . . . . . . . . . . . . . . . 22
S-9 Installation. . . . . . . . . . . . . . . . . . . . . . . . . 23 & 24 Chapter 10: Installation Equipment
Flush Mount S-9 Anchor . . . . . . . . . . . . . . . . . . . . . 25 @=CB7<5
113AA=@73A
























(
/<2
(
&@=831B
&6=B=A



















 Grout Pumps & Hydraulic Jacks . . . . . . . . . . . . . . . 48
Torque Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Chapter 4: S-7 Reusable Concrete Anchor
Torque Tension Graphs . . . . . . . . . . . . . . . . . . 50 & 51
(
<4=@;/B7=<





























(
<16=@
/B/




























(
3A75<
=<A723@/B7=<A




















(
>>:71/B7=<A




























(
<AB/::/B7=<






























Technical Assistance
Let Williams help save you thousands of dollars in start up costs by acting as an on-site advisor during your anchor
bolt installation.
Our technician will work directly with your superintendent and crews to see they are prepared in terms of equipment
needs, material coordination, and efficient installation procedures to yield the best productivity possible.
Our technicians are trained in most types of anchoring conditions and can often trim days off the bolting schedule by
recommending efficient procedures. Technicians may also prove to be very beneficial in consulting with the design engi-
neer to propose any last minute design changes to accommodate field conditions. Even the simplest anchoring job could
have delays for an inexperienced crew. Take advantage of our expertise and be prepared to keep your project on
schedule.

*Advance notification is requested. Contact your nearest Williams Representative for fee schedules.
 Different Types of Concrete Anchors
When to use Williams
For decades Williams Form Engineering Corp. has gained a world-wide reputation as the one source that contractors,
designers, and owners consistently turn to in solving their most complex needs for high capacity concrete anchors.
Williams supplies post-installed mechanical and chemical high capacity concrete anchors as well as cast-in-place
anchors depending on application need and design parameters. You can count on Williams for your next project whether
it’s a retro-fit need such as a vibratory restraint, seismic upgrade, or a need for a new project such as a bridge or power
plant.
Mechanical Anchors
Williams mechanical anchors are often used when a post-installed prestressed anchor is needed to resist heavy or
vibratory loading. Each anchor is prestressed (proof- loaded) typically to a 2:1 safety factor based on the anchor’s ulti-
mate tensile strength. A “locked-in” prestress load provides a test to verify the holding capacity and also will protect the
anchor against fatigue from cyclical loading situations. In addition, many of Williams mechanical anchors can be cement
grouted to provide corrosion protection and also to help lock in the prestress load. Williams mechanical anchors have
been used for foundation repair, structural supports, bridge applications and countless other situations that demand a
high degree of structural safety.

e
riv
D
ge
ed
r
r

ho
ho

Sl
r
ho

nc
nc

ar
nc

A
tA

eb
A

R
cu

bl
k

ad
oc

sa
er

re
-L

nd

eu

Th
in

R
Sp

7 

ll-
9
S-

S-

A
75
de
ra
G

Bonded Anchors
Williams Form Engineering offers the best in epoxy concrete anchoring. Epoxy dowels are ideal for static loads, shear
loads or applications that require close spacing and edge distances. Unlike mechanical anchors, epoxy anchors do not
exert the lateral stress that a mechanical anchor would along a concrete drill hole surface. Epoxy anchors are capable
of reaching high bond-stress values in relatively fast cure times.
Williams also supplies cement grout-bond, post-installed anchor systems. These anchors are less sensitive to tem-
perature and cement grout can be pumped more ideally for longer length anchor embedments. Cement grout also offers
an excellent barrier against corrosion.

5-Star Cement Grout

Wil-X Cement Grout

Ultrabond 1 Ultrabond 2
 Different Types of Concrete Anchors
Cast-in-Place Anchors
Williams manufactures cast-in-place anchors with threaded bars up to 3-1/2" in diameter and stock lengths up to 50
feet. Williams can customize an anchor system for virtually any cast-in-place application. Williams can supply threaded
bar with an embedded plate-nut assembly, Stress Gradient Pigtail Anchors, headed anchor studs and customized J, U
and L bolts. Contact our engineering department for details not shown in this catalog.

Stress Gradient Pigtail Anchor

Embedded Plate-Nut Assembly

J-Bolt Bent Rebar

Concrete Anchor Design

Concrete Anchor Design Models
<
B63
>/AB
,7::7/;A
6/A
@31=;;3<232
B63
CA3
=4


/>>3<27F

E6716
CB7:7H32
/
L
1=<3
;3B6=2
4=@
23A75<-
ing concrete anchor bolt systems. A new model is presently available in ACI 318 appendix D, however the database
used to generate this new model was primarily derived from test data that included anchors up to 1" in diameter. For
larger diameter anchors 1" and greater, the method shown in ACI 318 appendix D does not have a time tested record
to demonstrate the effectiveness of its current equations. Some adjustment factors to the concrete breakout equation
would need to be applied for anchors larger than 1" diameter in the future as the anchor test database increases to
accommodate deep embedded anchors. The model presented in ACI 318 appendix D when used for large diameter
/<16=@A
27/;3B3@A
03BE33<

/<2


E=C:2
BG>71/::G
03
;=@3
1=<A3@D/B7D3
B6/<
B63
L
1=<3
;3B6=2
0CB
7B
;/G
/:A=
be restrictive. Williams recommends designers use the models they are most comfortable with for deep embedded
anchors and consult your Williams representative for test data that may be useful.

Concrete Anchor Testing

Williams has performed anchor tests spanning many years. Williams current capabilities allows testing deep embed-
ded anchors in most configurations. Most deep embedded anchor testing is done at Williams facilities.
Williams has supplied deep embedded concrete anchors for over 50 years and has gathered a vast amount of on site
testing, in house testing, and job experience related to the performance of large diameter anchor products. Some tests
described in codes, such as ACI 318 Appendix D and ACI 355.2, are cost prohibitive for large diameter anchors. These
tests were primarily written for small diameter anchors and recent findings have shown the economic impracticality for
large anchor systems. The space, concrete mass, equipment and experience are often not available for some of the
testing required by ACI 355.2 as it currently pertains to large diameter anchors. ACI has recently organized a task group
to study the economic problems related to testing large anchors in concrete. Please contact your Williams representa-
tive for guidance on deep embedded anchor systems.
 <'251+
4,
8.+

>
43+
+7/-3
+8.4*
Note: The following information is meant only as a quick reference. The reader should refer to ACI 355.1R-91 and
ACI 349 Appendix B, 1985 for complete information.
Excerpts from “State of the Art Report on Anchoring to Concrete” ACI 355.1R-91
([Link]) When the embedment of an anchor or group of anchors is insufficient to develop the tensile strength of the
anchor steel, a pullout cone failure of the concrete is the principal failure mode. When the spacing of anchors or loca-
tion of an edge interferes with the development of the full cone strength of an anchor, its capacity will be reduced.
In ACI 349 Appendix B, (ACI committee 349, 1985) the angle of the failure cone of headed and expansion anchors is
assumed as 45-degrees.
The following formulas have been developed to describe behavior of headed studs, expansion, and undercut anchors.

Anchor Tension Load

Concrete Cone Failure ([Link])
ACI 349 Appendix B, limits the tensile capacity of cone failure of an anchor or group of anchors, to a uniform stress
on the stress cone surface of the anchors.
= Strength reduction factor
= .85 for uncracked concrete
= 
7<
H=<3
=4
>=B3<B7/:
1@/197<5
(3.2) = The summation of the projected areas of individual stress
cones minus the areas of overlap 2
and of any area, or areas,
cut off by intersecting edges (in )
= Tensile capacity of the concrete cone (lbs.)
= Concrete Compressive strength (psi)

Minimum Edge Distance ([Link])

With respect to the minimum edge distance, tests reported a direct relationship between anchor load and side cone
failure. The equation below is a more correct design boundry for the edge distance for headed anchors.

= ASTM - specified tensile strength of the anchor bolt (kips)

  = Minimum edge distance (in.)
= Concrete Compressive strength (psi)

Side Cone Bursting ([Link])

The average failure load for a side cone (bursting) failure is given as:

= Actual edge distance (in.)

  = Failure load of side cone bursting (kips)
= Concrete Compressive strength (psi)

Splitting Failure ([Link])

With respect to minimum edge distance, the following criteria is proposed to preclude splitting failure occurring at a
load lower than the capacity of the concrete cone failure or pullout. This equation is valid for anchor spacing S ≥ 2 in.

= Minimum edge distance (in.)

(3.21) = Anchor bolt diameter (in.)
= Embedment depth to the bottom of the anchor (in.)
 <'251+
4,
8.+

>
43+
+7/-3
+8.4*
Anchor Shear Loading
Steel Failure ([Link])
Steel failure usually occurs after relatively large displacements and is most common for deep embedments, lower
strength steels and large edge distances. The failure load depends on the steel area and the steel strength and given
by:
= Where the factor takes account of the steel “shear” strength
/<2
6/A
B63
@/<53

B=

2
(3.22) = Tensile stress area (in )
= Ultimate tensile strength (psi)
= Ultimate shear strength of steel (lbs.)

Edge Failure ([Link].1)

For all types of anchors loaded in shear toward an adjacent, free edge and exhibiting a concrete failure, the failure
load is influenced by the concrete tensile strength, the edge distance m and the stiffness of the anchor. Another influ-
encing factor is the embedment depth. The Failure surface has conical shape that may radiate from the embedded end
of the anchor for shallow embedments or from the upper part of the anchorage for deep embedments.
ACI 349 appendix B, Commentary gave a design shear strength of:
= .85
= Concrete Compressive strength (psi)
= Distance from anchor to free edge (in.)
(3.23) = 3.14
= Concrete shear breakout capacity (lbs.)

Minimum Edge Distance Shear ([Link].1)

ACI 349, Appendix B further recommends a minimum side cover or edge distance required to preclude edge fail-
ures, be calculated by:
= Anchor diameter (in.)
(3.24) = Anchor ultimate tensile load (lbs.)
= Concrete Compressive strength (psi)
= Minimum edge distance for shear loading (in.)

Critical Spacing ([Link].1)

Calculating the failure load of single fastenings situated in a corner or in narrow members. Klinger, Mendonca, and
Malik (1982) recommend a critical (minimum) edge spacing of:

= .9
= Critical minimum edge spacing (in)
(3.29) = Anchor diameter (in)
= ASTM - specified tensile strength of the anchor bolt (kips)
= Concrete Compressive strength (psi)

Combined Tension and Shear ([Link].2)

The behavior of anchors under combined tension and shear loading lies in between the behavior under tension or
shear loading, and for a given depth of embedment, is dependent on the angle of the loading.
To calculate the failure load under combined tension one approach is the straight-line function.
= Applied tensile and shear load, respectively
= Ultimate tensile and shear load, respectively
(3.32)
 Prestressed Concrete Anchors
Prestressed concrete anchors are often used for resisting cyclic or dynamic loading caused by wind or seismic events.
They are also used to limit or restrict structural movement due to anchor steel elongation. Common applications for pre-
stressed concrete anchors are tower anchoring, foundation repair, and heavy machinery tie down. Non-tensioned anchors or
passive dowels are often used for temporary support, resisting shear loads, static loading, or for applications with low con-
sequences of failure.
The prestressing of a concrete anchor is done by one of two methods. The preferred and most accurate way to prestress
an anchor is to use a hollow ram hydraulic jack which couples directly to the end of the anchor with a pull rod assembly. The
jack frame typically bears against the steel plate while the hydraulic ram transfers a direct tension load to the anchor. When
the prestress load is reached, the anchor nut is turned tightly against the anchor bearing plate, and the load from the jack is
released. The anchor nut prevents the steel from relaxing back to its original length, therefore, the anchor has been pre-
stressed. Once the anchor is put into service, additional elongation in the anchor rod only occurs if the applied load exceeds
the prestress load.
The second method of prestressing is to use a torque tension method. This is accomplished by simply turning the anchor
nut against the anchor bearing plate with a torque wrench. By using a “torque tension relationship” provided by Williams, the
installer can correlate the torque reading to a corresponding anchor tension load. Although not as accurate as direct ten-
sioning, it is often used for fast, economical installations in areas where hydraulic jacks would be cumbersome or difficult to
utilize. Torque tensioning is recommended to be done using a high-pressure lubricant on the anchor threads and under the
hex nut to reduce frictional resistance.

Benefits of a Prestressed Anchor: Prestressed Bolt

Pre-tested - By prestressing an anchor, each bolt is essentially “pre-test-
ed”, assuring it will hold its design load prior to final construction.
Eliminate Fatigue Stress - Fatigue failure is minimized since the service
load must exceed the prestressed load of the bolt to cause additional steel
elongation. Therefore, the periodic stretching and relaxing that causes
fatigue failure is eliminated.
Eliminate Uplift - Prestressing can eliminate a “floating” condition of a
foundation due to the natural hydraulic pressures or uplift loads caused by
wind or other overturning moments.
Negligible Bond Stress Relief - In cases where the concrete anchor free-
stress length is grouted after prestress, the grout hardens around the
deformations of the bar and bonds to the concrete in the drill hole to help
prevent stress relief in the bolt.
Corrosion Protection - A prestressed concrete anchor will not elongate
through the grout column in the free-stressing length. Elongation breaks
down and cracks the grout, opening the door to corrosion and eventual fail-
ure. This is a common problem with passive or “non-tensioned” concrete
dowels.

Dowel Bolt Non-Tensioned Dowels May Produce

the Following Effects:
Not Pre-Tensioned - Any application of load onto the bolt will cause the grout
to crack in the first several inches of drill hole depth.
Floating Condition - Allows floating of foundation or uplift of the structure due
to steel elongation.
Possible Fatigue Failure - Bolt can stretch and relax as the load varies.
Possible Corrosion Problem - Bolt elongation will crack protective grout cover.
Not Pre-Tested - The anchor holding capacity is not verified.
With a non-tensioned dowel, anchorage starts at the surface and actually
breaks down and cracks the grout as the load transfers deeper along the length
of the bolt. Over time the total anchorage may be lost due to these recurring
grout breakdowns.
 Corrosion Protection
Stainless Steel
Stainless steel can be specified for use with most of Williams anchors (except for Spin-Lock
mechanical anchors). Williams can supply anchor rods and components in grades of 304 and

4=@
CA3
7<
6756:G
1=@@=A7D3
3<D7@=<;3<BA

(B/7<:3AA
AB33:
7A
B63
03AB
;3/<A
=4
1=@@=A7=<
>@=-
tection available from Williams Form Engineering, however, steel strengths are often reduced
and anchor prices are increased. When specifying stainless steel make sure to specify the steel
grade and make note of the change in strengths from different stainless steel grades. Some
stainless steel types require longer lead times.

Electro Zinc Plating

Zinc plating is a process which deposits a thin layer of zinc over the steel. It is different from
galvanizing because zinc plating is an electro-chemical process and not a dip in molten zinc.
The advantages of zinc plating over galvanizing are control over zinc thickness and smoother
surfaces. The zinc protects the steel as a sacrificial coating. If the coating is damaged, the
sacrificial action continues as long as any zinc remains in the immediate area. Electro zinc plat-
7<5
A6=C:2
03
2=<3
7<
/11=@2/<13
E7B6
()#

)G>3


=;;3@17/:
H7<1
>:/B7<5
7A
1=;-
monly 0.0001 inches to 0.0005 inches in thickness and does not require oversized tapped
components.

Epoxy Coating
Fusion bonded epoxy coating of steel bars to help prevent corrosion has been successful-
ly employed in many applications because of the chemical stability of epoxy resins. Epoxy coat-
32
0/@A
/<2
4/AB3<3@A
A6=C:2
03
2=<3
7<
/11=@2/<13
E7B6
()#

=@
()#


=/B7<5
B6719<3AA
7A
53<3@/::G
A>3174732
03BE33<

B=

;7:A
>=FG
1=/B32
0/@A
/<2
4/AB3<3@A
/@3
AC0-
ject to damage if dragged on the ground or mishandled. Heavy plates and nuts are often gal-
vanized even though the bar may be epoxy coated since they are difficult to protect against
abrasion in the field. Epoxy coating patch kits are often used in the field for repairing nicked or
scratched epoxy surfaces. Epoxy Coating is used strictly on Williams cast-in-place, epoxy
bonded or cement grouted anchors. Not recommended for fine thread forms.

Hot Dip Galvanizing

Zinc serves as a sacrificial metal corroding preferentially to the steel. Galvanized bars
have excellent bond characteristics to grout or concrete and do not require as much care
in handling as epoxy coated bars. However, galvanization of anchor rods is more expen-
sive than epoxy coating and often has greater lead time. Hot dip galvanizing bars and
fasteners should be done in accordance with ASTM A153. Typical galvanized coating
thickness for steel bars and components is between 3 and 4 mils. 150 KSI high strength
steel bars should always be mechanically cleaned (never acid washed) to avoid
problems associated with hydrogen embrittlement in compliance with ASTM A143.
Hot Dip Galvanizing can be used on Williams Spin-Locks, cast-in-place anchors, epoxy and
cement grout anchors. Oversized tapped hex nuts should be used with hot dip galvanized bars.

End Caps
Williams offers several different types of PVC, metal, and nylon reinforced end caps to provide corrosion protection at otherwise
exposed anchor ends. Most often the caps are packed with corrosion inhibiting grease. Caps made from reinforced nylon and steel are
used in exposed impact areas.

Fiber Steel Tube welded on

Reinforced Flange with Threaded Steel Tube with Slip-On PVC Cap Screw-On
Nylon Cap Screw Connections Jam Nut with Plastic Nut PVC Cap
 Introduction
Williams Spin-Lock anchors were first used in the 1950’s for Comparison Proves
rock/roof bolting in projects such as NORAD and Australia’s
Williams Serrated Anchor
Snowy Mountain Power Facility. Since then many engineers, Spin-Lock Anchor by Others
contractors and owners have recognized the advantages of the
Spin-Lock anchor system as a high capacity concrete anchor.
Spin-Locks have been used successfully on rocket launch pads,
nuclear power plants, large dams and spillways, tower anchors, Uniform
Contact Point
roller coasters and several other applications requiring high Area Contacts
capacity and dynamic load resistant concrete anchor systems.
Williams Spin-Lock anchors provide the advantages of immedi-
ate anchorage, prestressing/post-tension abilities, anchorage
redundancy (mechanical anchorage with a grout bond), custom
manufacturing, and the highest capacities of any production
mechanical anchor available today.
To comply with the need for anchors which can be used in a Expansion shell receives Quartered cone design
full bearing support from leaves expansion shell
variety of applications with a wide range of loading capabili- solid 300° cone design. unsupported at adjacent
ties…Williams has developed a complete family of concrete gaps. Shell can collapse
anchor bolts with a simple and efficient system of installation. under high stress.
Williams also offers a line of rental equipment for installing, test-
ing and grouting of Spin-Lock high capacity concrete anchors.
Before proceeding with your next project, consult with a
design agency familiar with Williams anchor systems, or contact
your nearest Williams representative. Williams would be pleased
to recommend an ideal system to meet the needs of your next
application.

Spin-Lock Advantages
B The mechanical head allows for a prestressed anchor which prevents anchor fatigue
failure in cyclic or dynamic loading applications.
B Anchors can be custom manufactured or mechanically coupled to any length.
B Each anchor is tested to the desired working load.
B Anchors are grouted providing redundant anchorage, corrosion protection and the grout
helps to lock in prestress values.
B $0-
5-+0)61+)4
0-),
8:7>1,-;
)
.=44
 G
*-):16/
):-)
)6,
78-6;
8):)44-4
<7
<0-
,:144
074-
avoiding point loading.
B Anchors can be designed continuously threaded for field adaptation.
B Williams has testing equipment and personal that can work with an engineer for designs
with unique applications, locations or patterns.
B A selection of anchor bars is available to fit nearly every design.
B Williams Form can recommend several installation contractors in the area of the anchor
installation.
B High degree of dependability allows for a 2:1 safety factor.
B The Spin-Lock has been used in construction for over 50 years.
 R1H & R7S Spin-Lock Concrete Anchors

R1H High Grade Hollow-Core Anchor - ASTM A615 Deformation Pattern

!:-;<:-;;)*4-
B
!7;1<1>-
:7=<16/
B
!-:5)6-6< Up Bolting
Though years of development Williams has produced and patented the
Prestressable, Hollow-Core, Groutable Spin-Lock Concrete Anchoring Systems. The
hollow-core allows the anchor to always be grouted from the lowest gravitational point.
In an up-bolting situation, the grout is pumped in through the plastic grout tube and
begins to fill the drill hole from the plate. The grout rises until the entire hole is filled and
the grout returns through the hollow bar. In down grouting situations, the grout is
pumped through the hollow bar and starts at the bottom of the hole. Grout rises and
returns through the de-air tube when the hole is filled. Improperly or incomplete grout-
ed anchors are subjected to relaxation and corrosion. Because the Spin-Lock head
assembly provides 300º perimeter expansion anchorage and develops the full strength
of the rod, the hollow-core R1H Structural Properties
concrete anchor may be pre- Yield Ultimate Elongation Reduction
stressed to the desired load Stress Stress in 2” (51 mm) of Area
and tested prior to grouting. 91 KSI 124 KSI 15% min. 40% min.
(627 MPa) (854 MPa) Down Bolting

Dia & Recomm. Design Maximum Average Ultimate Drill Type Torque Ft.-Lbs. Embedment Part
Threads Load at Approx. Working Ultimate Shear Hole Head To Expand On Nut for Depth in 3000 PSI Number
per In. 2:1 Safety Factor Load to Yield Strength Strength Dia. (1) Ass’y Shell (2) Tension (5) Concrete (4)
1” - 8 33 kips 47 kips 66 kips 39.6 kips 1-3/4” 250 ft.-lbs. 15”
(176 kN) (44 mm) B 14 400 R1H08B14
(25 mm) (147 kN) (209 kN) (294 kN) (450*) (381 mm)
1-3/8” - 8 69 kips 100 kips 138 kips 82.8 kips 2-1/2” 750 ft.-lbs. 23”
(368 kN) (65 mm) B 20 Note (3) R1H11B20
(35 mm) (307 kN) (445 kN) (614 kN) (1200*) (584 mm)
2” - 6 150 kips 219 kips 300 kips 180 kips 3-1/2” 1000 ft.-lbs. 34”
(1334 kN) (801 kN) (89 mm) C 28 Note (3) R1H16C28
(51 mm) (667 kN) (974 kN) (2000*) (864 mm)

R7S Structural Properties

Yield Ultimate Elongation Reduction
Stress Stress in 20 Bar Dia. of Area
120 KSI 150 KSI 4% min. 20% min.
(827 MPa) (1034 MPa)

R7S 150 KSI Spin-Lock Concrete Anchor - ASTM A722

The R7S Spin-Lock Concrete Anchor incorporates a high strength post tension steel giving the designer the highest
strength to anchor diameter ratio available for use with the Spin-Lock head assembly.
Dia & Recomm. Design Maximum Average Ultimate Drill Type Torque Ft.-Lbs. Embedment Part
Threads Load at Approx. Working Ultimate Shear Hole Head To Expand On Nut for Depth in 3000 PSI Number
per In. 2:1 Safety Factor Load to Yield Strength Strength Dia. (1) Ass’y Shell (2) Tension (5) Concrete (4)
1” - 8 45.5 kips 72.7 kips 90.9 kips 54 kips 1-3/4” 500 ft.-lbs. 18”
(240 kN) (44 mm) C 14 680 R7S08C14
(25 mm) (202 kN) (324 kN) (404 kN) (650*) (457 mm)
1-1/4” - 7 72.7 kips 116 kips 145 kips 87 kips 2-1/2” 750 ft.-lbs. 23”
(389 kN) (64 mm) B 20 Note (3) R7S10B20
(32 mm) (323 kN) (517 kN) (647 kN) (1200*) (584 mm)
1-1/2” - 6 105 kips 169 kips 211 kips 126 kips 3” 1000 ft.-lbs. 26”
(559 kN) (76 mm) B 24 Note (3) R7S12B24
(38 mm) (469 kN) (750 kN) (937 kN) (1700*) (660 mm)
1-7/8” - 8 181 kips 289 kips 362 kips 216 kips 3-1/2” 1000 ft.-lbs. 36”
(1608 kN) (959 kN) (89 mm) C 28 Note (3) R7S15C28
(48 mm) (804 kN) (1286 kN) (2000*) (914 mm)
(*) Do not exceed these numbers
(1) Care should be taken to drill a straight and properly sized hole.
(2) More torque may be required on long anchors or if the head assembly is next to rebar. Consult your Williams Representative for more specific details.
(3) Stress to desired tensile load using a hollow ram hydraulic jack. Consult your Williams Representative.
(4) Full ultimate strength of anchor can be achieved at listed embedment depth, provided there are no edge or spacing effects on the anchor.
(5) All above torque values are for greased (MolyKote GN) threads.
(6) WILLIAMS reserves the right to ship full length or coupled units as necessary.
For Spin-Lock Accessories see page 41.
 R1S & R1J Spin-Lock Concrete Anchors
R1S Structural Properties
Diameter Yield Ultimate Elongation in 2” Reduction
Range Stress Stress )=/-
-6/<0 of Area
1/2” to 1” 92 KSI 120 KSI 11% min. 20% min.
(13 to 25 mm) (634 MPa) (827 MPa)
1-1/8” and up 81 KSI 105 KSI Meets strength of ASTM A325
11% min. 20% min.
(29 mm) (558 MPa) (723 MPa)

R1S High Tensile Spin-Lock Concrete Anchor - ASTM A108 / C1045

Williams R1S Spin-Lock Concrete Anchor utilizes a C-1045 steel which provides high strength capacity and has the
advantage of utilizing a more common steel for greater availability.
Dia & Recomm. Design Maximum Average Ultimate Drill Type Torque Ft.-Lbs. Embedment Part
Threads Load at Approx. Working Ultimate Shear Hole Dia. Head To Expand On Nut for Depth in 3000 PSI Number
per In. 2:1 Safety Factor Load to Yield Strength Strength (1) Ass’y Shell (2) Tension (5) Concrete (4)
1/2” - 13 8.53 kips 13.1 kips 17.1 kips 10.2 kips 1-1/4” 50 ft.-lbs. 7”
(75.8 kN) (45.5 kN) (32 mm) A 10 85 R1S04A10
(13 mm) (37.9 kN) (58.1 kN) (70*) (178 mm)
5/8” - 11 13.6 kips 20.8 kips 27.1 kips 16.3 kips 1-1/4” 125 ft.-lbs. 8”
(120.6 kN) (72.4 kN) (32 mm) A 10 125 R1S05A10
(16 mm) (60.3 kN) (92.5 kN) (250*) (203 mm)
3/4” - 10 20.1 kips 30.7 kips 40.1 kips 24.1 kips 1-3/4” C 14 210 ft.-lbs. 11”
210 R1S06C14
(19 mm) (89.2 kN) (137 kN) (178 kN) (107 kN) (44 mm) (250*) (279 mm)
7/8” - 9 27.7 kips 42.5 kips 55.4 kips 33.2 kips 1-3/4” C 14 390 ft.-lbs. 14”
390 R1S07C14
(22 mm) (123 kN) (189 kN) (246 kN) (148 kN) (44 mm) (410*) (356 mm)
1” - 8 36.4 kips 55.8 kips 72.7 kips 43.6 kips 1-3/4” C 14 500 ft.-lbs. 16”
550 R1S08C14
(25 mm) (162 kN) (248 kN) (323 kN) (194 kN) (44 mm) (600*) (406 mm)
1-1/8” - 7 40.5 kips 62 kips 81 kips 48.6 kips 2-1/4” C 18 550 ft.-lbs. 17”
770 R1S09C18
(29 mm) (180 kN) (284 kN) (360 kN) (216 kN) (57 mm) (600*) (432 mm)
1-1/4” - 7 51 kips 79 kips 102 kips 61.2 kips 2-1/4” C 18 750 ft.-lbs. 20”
1000 R1S10C18
(32 mm) (254 kN) (381 kN) (508 kN) (305 kN) (57 mm) (1200*) (508 mm)
1-3/8” - 8 65 kips 100 kips 130 kips 78 kips 2-1/2” 750 ft.-lbs. 22”
(347 kN) (64 mm) B 20 Note (3) R1S11B20
(35 mm) (289 kN) (445 kN) (578 kN) (1600*) (559 mm)
1-1/2” - 6 73.5 kips 113 kips 147 kips 88.2 kips 3” 1000 ft.-lbs. 23”
(392 kN) (76 mm) B 24 Note (3) R1S12B24
(38 mm) (327 kN) (503 kN) (654 kN) (1700*) (584 mm)
2” - 6 139 kips 215 kips 279 kips 167.4 kips 3-1/2” 1000 ft.-lbs. 34”
(1313 kN) (788 kN) (89 mm) C 28 Note (3) R1S16C28
(51 mm) (657 kN) (1080 kN) (2000*) (864 mm)

R1J Structural Properties

Diameter Yield Ultimate Elongation in
Range Stress Stress E
)=/-
-6/<0
1/2” to 1” 60 KSI 90 KSI 7% min.
(13 to 25 mm) (413 MPa) (621 MPa)
1-1/8” and up 60 KSI 90 KSI 9% min.
(29 mm) (413 MPa) (621 MPa)

R1J Solid Rebar Spin-Lock Concrete Anchor - ASTM A615

The R1J Spin-Lock Concrete Anchor uses an ASTM Grade 60 material for the anchor rod which is generally less
expensive than other Spin-Lock anchors which incorporate higher strength steels.
Dia & Recomm. Design Maximum Average Ultimate Drill Type Torque Ft.-Lbs. Embedment Part
Threads Load at Approx. Working Ultimate Shear Hole Head To Expand On Nut for Depth in 3000 PSI Number
per In. 2:1 Safety Factor Load to Yield Strength Strength Dia. (1) Ass’y Shell (2) Tension (5) Concrete (4)
1/2” - 13 6.35 kips 8.5 kips 12.8 kips 7.62 kips 1-1/4” 50 ft.-lbs. 7”
(56.8 kN) (34.1 kN) (32 mm) A 10 60 R1J04A10
(13 mm) (28.4 kN) (37.9 kN) (50*) (178 mm)
5/8” - 11 10.2 kips 13.6 kips 20.3 kips 12.2 kips 1-1/4” 100 ft.-lbs. 8”
(90.5 kN) (54.3 kN) (32 mm) A 10 110 R1J05A10
(16 mm) (45.2 kN) (60.3 kN) (100*) (203 mm)
3/4” - 10 15.0 kips 20.0 kips 30.1 kips 18.0 kips 1-3/4” C 14 165 ft.-lbs. 10”
175 R1J06C14
(19 mm) (66.9 kN) (89.1 kN) (134 kN) (80.2 kN) (44 mm) (165*) (254 mm)
7/8” - 9 20.8 kips 27.7 kips 41.6 kips 24.9 kips 1-3/4” C 14 265 ft.-lbs. 12”
290 R1J07C14
(22 mm) (92.5 kN) (123 kN) (185 kN) (111 kN) (44 mm) (265*) (305 mm)
1” - 8 27.3 kips 36.4 kips 54.5 kips 32.7 kips 1-3/4” C 14 400 ft.-lbs. 14”
420 R1J08C14
(25 mm) (121 kN) (162 kN) (243 kN) (146 kN) (44 mm) (400*) (356 mm)
1-1/8” - 7 34.3 kips 45.8 kips 68.7 kips 41.2 kips 2-1/4” C 18 450 ft.-lbs. 16”
610 R1J09C18
(29 mm) (153 kN) (204 kN) (306 kN) (183 kN) (57 mm) (550*) (406 mm)
1-1/4” - 7 43.6 kips 58.1 kips 87.2 kips 52.3 kips 2-1/4” C 18 750 ft.-lbs. 18”
810 R1J10C18
(32 mm) (194 kN) (259 kN) (388 kN) (233 kN) (57 mm) (750*) (457 mm)
1-3/8” - 8 55.4 kips 73.8 kips 111 kips 66.4 kips 2-1/2” 750 ft.-lbs. 22”
(295 kN) (64 mm) B 20 Note (3) R1J11B20
(35 mm) (246 kN) (328 kN) (492 kN) (1000*) (559 mm)
1-3/4” - 6 85.5 kips 114 kips 171 kips 102.6 kips 3” 1000 ft.-lbs. 26”
(761 kN) (456 kN) (76 mm) B 24 Note (3) R1J14B24
(38 mm) (380 kN) (507 kN) (1700*) (660 mm)
 B7S & R1V Spin-Lock Concrete Anchors
B7S Structural Properties
Diameter Yield Ultimate Elongation in 2” Reduction
Range Stress Stress )=/-
-6/<0 of Area
1/2” to 1” 92 KSI 120 KSI 11% min. 20% min.
(13 to 25 mm) (634 MPa) (827 MPa)
1-1/8” and up 81 KSI 105 KSI Meets strength of ASTM A325
11% min. 20% min.
(29 mm) (558 MPa) (723 MPa)

B7S Coil All-Thread Spin-Lock Concrete Anchor - ASTM A108 / C1045

Williams B7S Coil All-Thread Spin-Lock Concrete Anchor utilizes a C-1045 steel which provides high strength capac-
ity and has the advantage of utilizing a more common steel for greater availability.
Dia & Recomm. Design Maximum Average Ultimate Drill Type Torque Ft.-Lbs. Embedment Part
Threads Load at Approx. Working Ultimate Shear Hole Head To Expand On Nut for Depth in 3000 PSI Number
per In. 2:1 Safety Factor Load to Yield Strength Strength Dia. (1) Ass’y Shell (2) Tension (7) Concrete (4)
1/2” - 13 8.45 kips 13.0 kips 16.9 kips 10.1 kips 1-1/4” 50 ft.-lbs. 7”
(75.2 kN) (45.1 kN) (32 mm) A 10 85 B7S04A10
(13 mm) (37.6 kN) (57.7 kN) (70*) (178 mm)
5/8” - 11 13.3 kips 20.3 kips 26.5 kips 15.9 kips 1-1/4” 125 ft.-lbs. 8”
(118 kN) (70.8 kN) (32 mm) A 10 125 B7S05A10
(16 mm) (59.0 kN) (90.4 kN) (250*) (203 mm)
3/4” - 10 20.0 kips 30.6 kips 40.0 kips 24.0 kips 1-3/4” C 14 210 ft.-lbs. 11”
210 B7S06C14
(19 mm) (88.9 kN) (136 kN) (178 kN) (107 kN) (44 mm) (250*) (279 mm)
7/8” - 9 27.5 kips 42.1 kips 55.0 kips 33.0 kips 1-3/4” C 14 390 ft.-lbs. 14”
390 B7S07C14
(22 mm) (122 kN) (187 kN) (245 kN) (147 kN) (44 mm) (410*) (356 mm)
1” - 8 35.4 kips 54.3 kips 70.8 kips 42.5 kips 1-3/4” C 14 500 ft.-lbs. 16”
550 B7S08C14
(25 mm) (157 kN) (241 kN) (315 kN) (189 kN) (44 mm) (600*) (406 mm)
1-1/8” - 7 38.8 kips 59.9 kips 77.6 kips 46.6 kips 2-1/4” C 18 550 ft.-lbs. 17”
770 B7S09C18
(29 mm) (173 kN) (266 kN) (345 kN) (207 kN) (57 mm) (600*) (432 mm)
1-1/4” - 7 50.8 kips 78.5 kips 102 kips 61.0 kips 2-1/4” C 18 750 ft.-lbs. 20”
1000 B7S10C18
(32 mm) (226 kN) (349 kN) (452 kN) (271 kN) (57 mm) (1200*) (508 mm)
1-1/2” - 6 73.8 kips 114 kips 148 kips 88.5 kips 3” 1000 ft.-lbs. 23”
(394 kN) (76 mm) B 24 Note (3) B7S12B24
(38 mm) (328 kN) (506 kN) (656 kN) (1700*) (584 mm)

R1V Structural Properties

Yield Ultimate Elongation Reduction Charpy at
Stress Stress in 4 Bar Dia. of Area -40º F (-40º C)
105 KSI 125 KSI 20 ft/lbs
16% min. 50% min.
(723 MPa) (861 MPa) (27 Joules)

R1V High Impact Spin-Lock Concrete Anchor - ASTM A193 Grade B-7
The R1V Spin-Lock Concrete Anchor is often specified for applications in extreme cold temperatures or if the anchor
may be exposed to impact loading.
Dia & Recomm. Design Maximum Average Ultimate Drill Type Torque Ft.-Lbs. Embedment Part
Threads Load at Approx. Working Ultimate Shear Hole Dia. Head To Expand On Nut for Depth in 3000 PSI Number
per In. 2:1 Safety Factor Load to Yield Strength Strength (1) Ass’y Shell (2) Tension (5) Concrete (4)
1/2” - 13 8.9 kips 14.9 kips 17.8 kips 10.7 kips 1-1/4” 50 ft.-lbs. 7”
(79.0 kN) (47.4 kN) (32 mm) A 10 85 R1V04A10
(13 mm) (39.5 kN) (66.3 kN) (50*) (178 mm)
3/4” - 10 20.9 kips 35.1 kips 41.8 kips 25.1 kips 1-3/4” C 14 210 ft.-lbs. 12”
250 R1V06C14
(19 mm) (92.9 kN) (156 kN) (186 kN) (111 kN) (44 mm) (250*) (305 mm)
1” - 8 37.9 kips 63.6 kips 75.8 kips 45.5 kips 1-3/4” C 14 500 ft.-lbs. 16”
550 R1V08C14
(25 mm) (169 kN) (284 kN) (337 kN) (202 kN) (44 mm) (600*) (406 mm)
1-1/4” - 7 60.6 kips 102 kips 121 kips 72.7 kips 2-1/4” C 18 750 ft.-lbs. 22”
1000 R1V10C18
(32 mm) (269 kN) (453 kN) (538 kN) (323 kN) (57 mm) (1600*) (559 mm)
1-3/8” - 8 76.9 kips 129 kips 154 kips 92.3 kips 2-1/2” 750 ft.-lbs. 24”
(410 kN) (64 mm) B 20 Note (3) R1V11B20
(35 mm) (342 kN) (575 kN) (684 kN) (1600*) (610 mm)
1-1/2” - 6 87.8 kips 148 kips 176 kips 105 kips 3” 1000 ft.-lbs. 26”
(469 kN) (76 mm) B 24 Note (3) R1V12B24
(38 mm) (391 kN) (656 kN) (781 kN) (1700*) (660 mm)
1-3/4” - 5 119 kips 200 kips 238 kips 143 kips 3” 1000 ft.-lbs. 29”
(1056 kN) (634 kN) (76 mm) B 24 Note (3) R1V14B24
(45 mm) (528 kN) (887 kN) (1700*) (737 mm)
2” - 6 166 kips 278 kips 331 kips 199 kips 3-1/2” 1000 ft.-lbs. 35”
(1473 kN) (884 kN) (89 mm) C 28 Note (3) R1V16C28
(51 mm) (737 kN) (1238 kN) (4000*) (889 mm)
(*) Do not exceed these numbers
(1) Care should be taken to drill a straight and properly sized hole.
(2) More torque may be required on long anchors or if the head assembly is next to rebar. Consult your Williams Representative for more specific details.
(3) Stress to desired tensile load using a hollow ram hydraulic jack. Consult your Williams Representative.
(4) Full ultimate strength of anchor can be achieved at listed embedment depth, provided there are no edge or spacing effects on the anchor.
(5) All above torque values are for greased (MolyKote GN) threads.
(6) WILLIAMS reserves the right to ship full length or coupled units as necessary.
For Spin-Lock Accessories see page 41.
 Design Considerations for Spin-Locks
For several decades Engineers have successfully Prestressed Anchors for
/.@21
A526?
)=6; 9<08
12@64;@
<;
A52
M
0<;2
:2A5<1 Tower or Column Supports
that was presented in ACI 349 Appendix B (1985). This
method has worked effectively for Spin-Locks when used
in nuclear power plants, rocket launch pads, machinery
tie downs, foundation repair anchors and many more
applications.
At times, job conditions may dictate the necessity to
place adjacent anchors closer than the minimum spac-
ings (S) shown in the following table. When reduced
spacing is desired it is then recommended to install the
anchors by staggering the embedment depths. Adjacent
anchors should be staggered as shown in the illustration
below. After the deepest anchors have been drilled,
installed, grouted, and the grout has cured; the adjacent
anchors can be drilled and installed. This procedure
would allow for (S) values to be reduced by half without
the danger of fracture between holes during installation.
The ideal spacings are large enough to prevent blow
out from anchor hole to anchor hole, but not to develop
A52
3B99
0<:/6;21
.;05<?
0.=.06A62@


.@21
<;
A52
M
cone method in ACI 349 Appendix B (1985), the center
to center spacing to develop the full shear cone should
be 2 times the recommended embedment depth.
Closely spaced anchors can be designed with a deeper
embedment than what is listed in order to develop the
combined anchor capacities.
Adequate safety factors should always be applied
based on site and design conditions. For best results
Williams Spin-Lock anchors should be used in high
strength reinforced concrete.

Prestressing New Concrete to Old Concrete

 Design Considerations for Spin-Locks
Edge distance (E) may be reduced from the following chart if special care is taken during installation, working loads
are reduced, or heavy reinforcement is present in the side wall of the concrete. Williams has performed testing that
gives the designer a basic idea of what concrete failure loads to expect in non-reinforced concrete for reduced edge dis-
tances. These numbers are not recommendations, they are simply meant to be used as a reference. The designer
should compare the numbers below that are based on tests, to numbers determined from the design models of ACI 349
appendix B and/or values from ACI 318 Appendix D. Call the your Williams representative for additional test info.

Spin-Lock Concrete Anchors - Minimum Spacing & Edge Distances

Minimum Spacing Minimum Concrete Failure Loads
Average
Head Anchor Anchor Minimum to Prevent Hole Recommended 7 Bar ø 10 Bar ø 14 Bar ø 18 Bar ø
Ultimate
Assembly Type Diameter Embedment to Hole Blowout Edge Distance from the from the from the from the
Strength
Failure (S) (E) Edge (Test) Edge (Test) Edge (Test) Edge (Test)
1/2” 7” 6” 8” 17.1 kips 15 kips 17 kips (1) (1)
(13 mm) (178 mm) (152 mm) (203 mm) (75.8 kN) (67 kN) (75.8 kN)
R1S
5/8” 8” 7-1/2” 9” 27.1 kips 15 kips 19 kips 22 kips N.A.
(16 mm) (203 mm) (191 mm) (229 mm) (121 kN) (67 kN) (84.5 kN) (98 kN)
1/2” 7” 6” 8” 18 kips 15 kips
A10 R1V (1) (1) (1)
(13 mm) (178 mm) (152 mm) (203 mm) (80 kN) (67 kN)
1/2” 7” 6” 8” 12.7 kips 15 kips (1) (1) (1)
(13 mm) (178 mm) (152 mm) (203 mm) (56.5 kN) (67 kN)
R1J
5/8” 8” 7-1/2” 9” 20.3 kips 15 kips 19 kips 20 kips (1)
(16 mm) (203 mm) (191 mm) (229 mm) (90.3 kN) (67 kN) (84.5 kN) (89 kN)
1” 14” 12” 15” 66 kips 35 kips 66 kips
R1H (1) (1)
(25 mm) (356 mm) (305 mm) (381 mm) (294 kN) (156 kN) (294 kN)
3/4” 10” 9” 11” 30 kips 18 kips 30 kips (1) (1)
(19 mm) (254 mm) (229 mm) (279 mm) (134 kN) (80 kN) (134 kN)
B14
7/8” 12” 10-1/2” 14” 41.5 kips 18 kips 41.5 kips
R1J (1) (1)
(22 mm) (305 mm) (227 mm) (356 mm) (185 kN) (80 kN) (185 kN)
1” 15” 12” 15” 54 kips 35 kips 54 kips (1) (1)
(25 mm) (381 mm) (305 mm) (381 mm) (240 kN) (156 kN) (240 kN)
1-3/8” 24” 16-1/2” 22” 138 kips 90 kips 102 kips
R1H N.A. N.A.
(35 mm) (610 mm) (419 mm) (559 mm) (614 kN) (400 kN) (454 kN)
1-3/8” 24” 16-1/2” 22” 154 kips 90 kips 102 kips
R1V N.A. N.A.
(35 mm) (610 mm) (419 mm) (559 mm) (684 kN) (400 kN) (454 kN)
B20
1-3/8” 22” 16-1/2” 22” 110 kips 90 kips 102 kips
R1J N.A. (1)
(35 mm) (559 mm) (419 mm) (559 mm) (489 kN) (400 kN) (454 kN)
1-1/4” 18” 15” 20” 145 kips 82 kips 87 kips
R7S N.A. N.A.
(32 mm) (457 mm) (381 mm) (508 mm) (649 kN) (365 kN) (387 kN)
1-1/2” 26” 19-1/2” 27” 210 kips 90 kips 102 kips 208 kips
B24 R7S N.A.
(38 mm) (662 mm) (495 mm) (686 mm) (932 kN) (400 kN) (454 kN) (925 kN)
3/4” 12” 9” 11” 40.1 kips 33 kips 42 kips (1) (1)
(20 mm) (305 mm) (229 mm) (279 mm) (178 kN) (147 kN) (187 kN)
7/8” 14” 10-1/2” 14” 55.4 33 kips 42 kips
R1S (1) (1)
(22 mm) (356 mm) (267 mm) (356 mm) (246 kN) (147 kN) (187 kN)
1” 16” 12” 15” 72.7 kips 55 kips 67 kips (1) (1)
(25 mm) (406 mm) (305 mm) (381 mm) (323 kN) (245 kN) (298 kN)
C14
3/4” 11” 9” 11” 42 kips 33 kips 42 kips (1) (1)
(19 mm) (279 mm) (229 mm) (279 mm) (187 kN) (147 kN) (187 kN)
R1V
1” 16” 12” 15” 76 kips 55 kips 67 kips N.A. N.A.
(25 mm) (406 mm) (305 mm) (381 mm) (338 kN) (245 kN) (298 kN)
1” 18” 13” 17” 90 kips 55 kips 67 kips 91 kips
R7S (1)
(25 mm) (457 mm) (330 mm) (432 mm) (400 kN) (245 kN) (298 kN) (405 kN)
1-1/4” 20” 15” 20” 102 kips 82 kips 92 kips 102 kips
R1S (1)
(32 mm) (508 mm) (381 mm) (508 mm) (508 kN) (365 kN) (409 kN) (454 kN)
1-1/8” 16” 13-1/2” 18” 68 kips 68 kips
C18 N.A. (1) (1)
(30 mm) (406 mm) (343 mm) (457 mm) (303 kN) (302 kN)
R1J
1-1/4” 23” 16” 22” 87 kips 82 kips 92 kips (1) (1)
(32 mm) (584 mm) (406 mm) (559 mm) (387 kN) (365 kN) (409 kN)
2” 33” 24” 32” 300 kips 180 kips 283 kips 300 kips
R1H N.A.
(51 mm) (838 mm) (610 mm) (813 mm) (1334 kN) (801 kN) (1259 kN) (1334 kN)
2” 35” 24” 32” 330 kips 180 kips 283 kips 330 kips
C28 R1V N.A.
(51 mm) (889 mm) (610 mm) (813 mm) (1467 kN) (801 kN) (1259 kN) (1468 kN)
1-7/8” 36” 24” 35” 360 kips 180 kips 283 kips 330 kips
R7S N.A.
(48 mm) (914 mm) (610 mm) (889 mm) (1598 kN) (801 kN) (1259 kN) (1468 kN)
(1) Ultimate Strength of the steel was reached.
(N.A.) No test data is available
Concrete compressive strengths were between 3000-4500 psi with the exception of the C28 tests which were performed in high strength 5000 psi concrete.
All tests were performed in unreinforced concrete.
 Spin-Lock Head Assembly
*52
-6996.:@
)=6; "<08
.;05<?
.@@2:/9F
46C2@
3B99
M
/2.?6;4
.?2.


*52
@:<<A5
@5299
12@64;
.99<D@
3<?
:.[Link]
shell to concrete contact and eliminates “point of contact” created by serrated designs. The cone design supports the
shell 300°, thereby eliminating any possible collapse of the shell under high load conditions. The thrust ring stop in front
of the shell prevents any possible rebound of the expanded shell down the cone if subjected to impact loading. The
Williams Spin-Lock anchor has been field proven on the world’s largest projects to far exceed in tension capacity any
other production mechanical anchor on the market.

Type A - Short Shell & Cone

Standard Standard Overall
Head Drill Hole Bolt Dia. & Cone MAL Shell Assy.
Assembly Dia. Thread Form Length & Length & Length
Part Num. Part Num.
1/2” - 13 NC 1-7/8”
1-1/4” (13 mm) SC-114-4 1-7/8” 4-1/4”
A10 (32 mm) 5/8” - 11 NC 1-7/8” SS-114 (108 mm)
(16 mm) SC-114-5

Type B - Long Shell & Cone

Long MAL
Long Cone Overall
Head Drill Hole Bolt Dia. & Shell
Length & Assy.
Assembly Dia. Thread Form Length &
Part Num. Length
Part Num.
1-3/4” 1” - 8 NC 3-3/4” 3-3/4” 8-1/4”
B14 (44 mm) (25 mm) LC-158-8 LS-175 (210 mm)
1-1/4” - 7 NC 9-3/8”
2-1/2” (32 mm) 4” 4” (238 mm)
B20 (65 mm) 1-3/8” - 8 NC LC-250 LS-250 9-1/2”
(35 mm) (241 mm)
1-1/2” - 6 NC 12-5/8”
3” (38 mm) 5-1/2” 5-1/2” (321 mm)
B24 (76 mm) 1-3/4” - 5 NC LC-300 LS-300 12-7/8”
(45 mm) (327 mm)

Type C - Long Shell & Cone with Flange

Long Cone Long MAL Overall
Head Drill Hole Bolt Dia. & w/ Flange Shell Assy.
Assembly Dia. Thread Form Length & Length & Length
Part Num. Part Num.
3/4” - 10 NC 4-1/4” 9”
(19 mm) LCF-175-6 (229 mm)
1-3/4” 7/8” - 9 NC 4-1/4” 3-3/4” 9-1/16”
C14 (44 mm) (22 mm) LCF-175-7 LS-175 (230 mm)
1” - 8 NC 4-1/4” 9-3/16”
(25 mm) LCF-175-8 (233 mm)
1-1/8” - 7 NC 4-7/8” 10”
2-1/4” (30 mm) LCF-225-9 4” (254 mm)
C18 (57 mm) 1-1/4” - 7 NC 4-7/8” LS-225 10-1/4”
(32 mm) LCF-225-10 (260 mm)
1-7/8” - 8 UN 15”
3-1/2” (48 mm) 7” 6” (381 mm)
C28 (89 mm) 2” - 6 UN LCF-350-16 LS-350 15-1/8”
(51 mm) (384 mm)

Coupled Head Assemblies

Williams can manufacture Spin-Lock Anchor systems
with the use of a transition coupling, which allows the
anchor to be designed with a continuously workable
thread-form. This is advantageous when the anchor length may need to be adjusted in the field due to variable site con-
ditions. The transition coupling engages a continuously threaded U.N. bar into the head assembly and the All-Thread
Bar (typically Grade 75 All-Thread Rebar or 150 KSI All-Thread-Bar) is attached to the other end of the coupling.
 Spin-Lock Installation
Step 1: Drilling
Use Hammer Drill
or Core Drill
Care should be taken to insure an
accurate diameter and the drilled hole
is as perpendicular to the concrete
surface as possible. The hole depth Concrete
should be drilled 2” to 3” deeper than
Down Bolting
the anchor embedment depth. Clean situations
the drill hole by blowing air at the bot- require
drilling holes
tom of the hole to remove debris. 2” to 3”
beyond the
length of the
Concrete
Anchor

Drill
Hole

Heavy Setting Tool

Duty
Hex Nut

Steel Plate Step 2: Anchor Placement

Place the nut, washer, bevel washers (if
required), and plate on the anchor. Insert the
Hollow-Core anchor into the hole to correct anchor embed-
Concrete
Anchor
Spin-Lock
ment depth. If the anchor becomes stuck in
being
:7=<
74-
the hole, attach the setting tool to the end of
inserted
into hole the anchor and drive it into the hole with a
hammer. If the anchor slides into the hole
Malleable Thrust Ring extremely loose, remove the anchor from the
Shell
Slip Ring hole. Pre-expand the anchor head 1/2 revolu-
Cone tion or until it fits snugly into the drill hole.

Step 3: Setting the Anchor Deep Socket for

Impact Tool or
Before placing the setting tool on the Torque Wrench

anchor, it should be inspected to insure both Setting

sections are turned tightly together and the Tool

washers are greased. Install setting tool

fully onto the exposed threaded end of the 1-2 Bar
Diameters
anchor. Initially torque the anchor with an of Thread
impact gun. This action migrates the cone
into the shell, thus expanding the mechani-
cal anchor into the concrete. The final
torque can be checked and adjusted with a
manual or hydraulic torque wrench.
Remove the setting tool by restraining the
lower section while rotating its upper section
counter-clockwise until the setting tool is
loose.
 Spin-Lock Installation
Step 4a: Testing the
Anchor
Method A: Tensioning
with a Test Jack
Place the jack and frame
over the anchor and attach
the test rod and couplings to
the anchor. Make sure the
coupling is fully engaged.
Attach the test nut and test
plate over the test rod on top
of the jack. Test the anchor by
tensioning the jack to the
required test load (usually half
of the ultimate strength) but
never to exceed the adver-
tised yield strength of the anchor. Adjust the jack to the required final tension and lock in the final prestress load. This
is done by tightening the concrete anchor hex nut with a knocker wrench (through the frame opening) until a slight reduc-
tion is noticed on the jack gauge. The full prestress load will be transferred to the anchor bolt once the tension in the
test jack has been released and test components removed.

Step 4b: Testing the Anchor

Method B: Testing by Torque Tensioning
Tension the anchor by torquing the hex nut with a torque wrench. To obtain the advertised tensile working load, see
the "Torque On Nut" column on the Spin-Lock Anchor charts listed on pages 11-13. For other desired loads, see the
torque tension graphs shown on pages 50 & 51. Please Note: The torque/tension relationship is not as accurate as
direct tensioning with a hydraulic jack and should not be used where critical tension loads need to be verified.

Step 5: Grouting the Anchor

When Grouting the anchor, always grout from the lowest gravitational point. Continue grouting until a steady stream
of pure grout is seen coming out around the bearing plate or grout tube, and/or from the de-air tube. For solid anchors,
a separate grout tube must be placed in the drill hole (through an opening in the bearing plate) as deep as possible
before grouting. Down-grouting of Hollow Core Spin-Locks can be simply grouted through the hollow core by attaching
a grout tube adapter to the outer end of the ten-
:75
:7=<
Pump
sioned anchor and grouting. When the grouting is
:7=<
$=*- complete, all air and standing water has been
:7=<
$=*- removed from the drill hole by displacement. :7=<
47?
through
Adapter
De-Air Tube and
through De-Air
Keyhole through
Keyhole

:7=<16/
) :7=<16/
)
Hollow-Core Solid Bar
Spin-Lock Spin-Lock

:7=<
47?

Williams offers a field installation advising service to aid contractors in the initial installation process of installing all
types of concrete anchors. A Williams “Spin-Lock Anchor Installation Video” is also available upon request. Contact
your Williams sales representative for details.
 Spin-Lock Anchor Project Photos

Project: Woodrow Wilson Bridge Project: Marine Terminal

Contractor: American Bridge Contractor: Toledo Caisson
Location: Washington DC Location: Toledo, OH

Project: Chicago Elevated Train Project: Long Beach Cruise Terminal

Contractor: Kiewit Designer: CH2M Hill
Location: Chicago, IL Contractor WW Stevenson
Location: Long Beach, CA

Project: Cape Canaveral Launch Site Project: Tennessee DOT Cantilever Sign Retrofit
Contractor: Bechtel National Contractor: Thompson & Thompson
Location: Cape Canaveral, FL Location: Throughout Tennessee
 S-9 Undercut Concrete Anchor
Williams S-9 Undercut Bearing Anchor was designed to eliminate the direct lateral stress found in the setting of con-
ventional anchors and to bring its characteristics closer to those of cast-in-place anchors. Through the use of Williams
undercutting tool, along with Williams undercut anchor, the conical shape of the anchor fits into the conical cut of the hole.
This produces a positive expansion anchoring system that develops the tensile capacity of the bolt without slip or con-
crete failure. Because the anchor head is larger than the drill hole size, a properly embedded anchor will consistently
develop 100% of the ASTM A193 Grade B7 bolting material.

Cone Shell Sleeve Washer Hex Nut Stud

Advantages of Williams Undercut Anchors

Cyclic Loading in Cracked Concrete
In situations where the diameter of the hole is increased due to changes Undercut
Hole
caused by nature, the S-9 Undercut Bearing Anchor withstands cyclic loads in
the cracked concrete member because the undercut of the hole is much larger
than the top of the hole.
High Levels of Preload
Williams high strength stud bolt is threaded the total length of the bar to pro-
vide uniform stress throughout the bolt. When combined with Williams undercut
head assembly the product is an anchor which will retain a much higher preload
than a standard friction anchor.
Undercut
Vibratory Loads (See pages 6 & 7 for common failure modes) Anchor
Throughout the destructive testing on Williams undercut anchor there has
been consistent ductile failure on the stud bolt demonstrating a high reliability of
safety. Therefore the S-9 Undercut anchor may be used safely with vibration
equipment and piping.
S-9 Undercut Concrete Anchor - ASTM A193 Grade B7
Minimum Minimum Allowable Allowable
Bar Drill Hole Ultimate Yield Ultimate Elongation
in 20 Bar Reduction Part
Strength Yield Tension Simple Shear Stress
Diameter Diameter Stress Diameters of Area Number
(FpuA) (2) Strength .5 (FpuA) .17 (FpuA) (1)
1/4" - 20 UNC 5/8” 3.98 kips 3.34 kips 1.99 kips 0.677 kips 105 KSI 125 KSI 16% 50% S9T-02
(6.4 mm) (16 mm) (17.7 kN) (14.9 kN) (8.92 kN) (3.01 kN) (723 mPa) (861 mPa)
3/8” - 16 UNC 7/8” 9.69 kips 8.14 kips 4.84 kips 1.65 kips 105 KSI 125 KSI 16% 50% S9T-03
(9.5 mm) (22 mm) (43.1 kN) (36.2 kN) (21.5 kN) (7.34 kN) (723 mPa) (861 mPa)
1/2" - 13 UNC 7/8” 17.7 kips 14.9. kips 8.85 kips 3.01 kips 105 KSI 125 KSI 16% 50% S9T-04
(13 mm) (22 mm) (78.9 kN) (66.3 kN) (39.4 kN) (13.4 kN) (723 mPa) (861 mPa)
5/8" - 11 UNC 1-1/8” 28.2 kips 23.7 kips 14.5 kips 4.93 kips 105 KSI 125 KSI 16% 50% S9T-05
(16 mm) (29 mm) (125 kN) (105 kN) (64.5 kN) (22.0 kN) (723 mPa) (861 mPa)
3/4" - 10 UNC 1-1/8” 41.8 kips 35.1 kips 20.9 kips 7.11 kips 105 KSI 125 KSI 16% 50% S9T-06
(19 mm) (29 mm) (187 kN) (156 kN) (93.6 kN) (31.6 kN) (723 mPa) (861 mPa)
1" - 8 UNC 1-5/8” 75.8 kips 63.6 kips 37.9 kips 12.9 kips 105 KSI 125 KSI 16% 50% S9T-08
(25 mm) (41 mm) (337 kN) (283 kN) (168 kN) (57.4 kN) (723 mPa) (861 mPa)
1-1/4" - 7 UNC 2” 121 kips 102 kips 60.6 kips 20.6 kips 105 KSI 125 KSI 16% 50% S9T-10
(32 mm) (51 mm) (539 kN) (453 kN) (269 kN) (91.6 kN) (723 mPa) (861 mPa)
1-1/2" - 6 NC 2-1/2” 176 kips 148 kips 87.8 kips 29.9 kips 105 KSI 125 KSI 16% 50% S9T-12
(38 mm) (64 mm) (781 kN) (656 kN) (390 kN) (133 kN) (723 mPa) (861 mPa)
These loads are valid where embedment is sufficient to assure steel failure; that is concrete shear cone strength is greater than steel strength.
(1) Allowable Simple Shear load per AISC Table 1-D.
(2) Minimum ultimate static tension values based on physicals of ASTM A193 Grade B7 bolting material having 125,000 PSI minimum ultimate
 Stainless Steel Grade S-9 Undercut Anchor
Presented below are four different stainless steel options for the S-9 Undercut Concrete Anchor. Generally, the
Stainless 304 B8 Class 1 and the Stainless 316 B8M Class I S-9 Undercut Concrete Anchors are the least expensive
and most readily available of the Stainless Steels. The Stainless 304 B8 Class II S-9 boasts the highest strength among
the Stainless Steels, while the 316 B8M Class II S-9 provides the most protection from corrosion.
Stainless S-9 Undercut Concrete Anchor - ASTM A193 304 B8 & 316 B8M Class I
Minimum Minimum Allowable Allowable
Bar Drill Hole Ultimate Yield Ultimate Elongation
in 4 Bar Reduction Partial Part
Strength Yield Tension Simple Shear
Diameter Diameter Stress Stress Diameters of Area Number
(FpuA) Strength .6 (FyA) .17 (FpuA) (1)
1/4" - 20 UNC 5/8” 2.39 kips 0.95 kips 0.570 kips 0.405 kips 30 KSI 75 KSI S9T-02-S4
30% 50%
(6.4 mm) (16 mm) (10.6 kN) (4.2 kN) (2.54 kN) (1.81 kN) (207 mPa) (517 mPa) S9T-02-S6
3/8” - 16 NC 7/8” 5.81 kips 2.32 kips 1.39 kips 0.988 kips 30 KSI 75 KSI S9T-03-S4
30% 50%
(9.5 mm) (22 mm) (25.8 kN) (10.3 kN) (6.18 kN) (4.39 kN) (207 mPa) (517 mPa) S9T-03-S6
1/2" - 13 UNC 7/8” 10.6 kips 4.26 kips 2.56 kips 1.81 kips 30 KSI 75 KSI S9T-04-S4
30% 50%
(13 mm) (22 mm) (47.3 kN) (18.9 kN) (11.5 kN) (8.05 kN) (207 mPa) (517 mPa) S9T-04-S6
5/8" - 11 UNC 1-1/8” 16.9 kips 6.78 kips 4.07 kips 2.88 kips 30 KSI 75 KSI S9T-05-S4
30% 50%
(16 mm) (29 mm) (75.4 kN) (30.2 kN) (18.1 kN) (12.8 kN) (207 mPa) (517 mPa) S9T-05-S6
3/4" - 10 UNC 1-1/8” 25.1 kips 10.0 kips 6.00 kips 4.26 kips 30 KSI 75 KSI S9T-06-S4
30% 50%
(19 mm) (29 mm) (111 kN) (44.6 kN) (26.7 kN) (18.9 kN) (207 mPa) (517 mPa) S9T-06-S6
1" - 8 UNC 1-5/8” 45.5 kips 18.2 kips 10.9 kips 7.73 kips 30 KSI 75 KSI S9T-08-S4
30% 50%
(25 mm) (41 mm) (202 kN) (80.9 kN) (48.5 kN) (34.6 kN) (207 mPa) (517 mPa) S9T-08-S6
1-1/4" - 7 UNC 2” 72.7 kips 29.1 kips 17.5 kips 12.4 kips 30 KSI 75 KSI S9T-10-S4
30% 50%
(32 mm) (51 mm) (323 kN) (129 kN) (77.8 kN) (55.0 kN) (207 mPa) (517 mPa) S9T-10-S6
1-1/2" - 6 NC 2-1/2” 105 kips 42.2 kips 25.3 kips 17.9 kips 30 KSI 75 KSI S9T-12-S4
30% 50%
(38 mm) (64 mm) (469 kN) (188 kN) (112 kN) (79.5 kN) (207 mPa) (517 mPa) S9T-12-S6
See notes at bottom

Stainless S-9 Undercut Concrete Anchor - ASTM A193 304 B8 Class II

Minimum Minimum Allowable Allowable
Bar Drill Hole Ultimate Yield Ultimate Elongation
in 4 Bar Reduction Partial Part
Strength Yield Tension Simple Shear
Diameter Diameter Stress Stress Diameters of Area Number
(FpuA) Strength .6 (FyA) .17 (FpuA) (1)
1/4" - 20 UNC 5/8” 3.98 kips 3.18 kips 1.91 kips 0.670 kips 100 KSI 125 KSI 12% 35% S9T-02-S42
(6.4 mm) (16 mm) (17.7 kN) (14.1 kN) (8.50 kN) (2.98 kN) (690 mPa) (862 mPa)
023/8” - 16 NC 7/8” 9.69 kips 7.75 kips 4.65 kips 1.65 kips 100 KSI 125 KSI 12% 35% S9T-03-S42
(9.5 mm) (22 mm) (43.1 kN) (34.5 kN) (20.7 kN) (7.33 kN) (690 mPa) (862 mPa)
1/2" - 13 UNC 7/8” 17.7 kips 14.2 kips 8.52 kips 3.01 kips 100 KSI 125 KSI 12% 35% S9T-04-S42
(13 mm) (22 mm) (78.9 kN) (63.1 kN) (37.9 kN) (13.4 kN) (690 mPa) (862 mPa)
5/8" - 11 UNC 1-1/8” 28.2 kips 22.6 kips 13.6 kips 4.79 kips 100 KSI 125 KSI 12% 35% S9T-05-S42
(16 mm) (29 mm) (126 kN) (101 kN) (60.5 kN) (21.3 kN) (690 mPa) (862 mPa)
3/4" - 10 UNC 1-1/8” 41.8 kips 33.4 kips 20.0 kips 7.10 kips 100 KSI 125 KSI 12% 35% S9T-06-S42
(19 mm) (29 mm) (186 kN) (149 kN) (88.96 kN) (31.6 kN) (690 mPa) (862 mPa)
1" - 8 UNC 1-5/8” 69.7 kips 48.4 kips 29.0 kips 11.8 kips 80 KSI 115 KSI 15% 35% S9T-08-S42
(25 mm) (41 mm) (310 kN) (215 kN) (129 kN) (52.9 kN) (552 mPa) (793 mPa)
1-1/4" - 7 UNC 2” 102 kips 63.0 kips 37.8 kips 17.3 kips 65 KSI 105 KSI 20% 35% S9T-10-S42
(32 mm) (51 mm) (453 kN) (280 kN) (167 kN) (77.5 kN) (448 mPa) (724 mPa)
1-1/2" - 6 NC 2-1/2” 141 kips 70.2 kips 42.1 kips 25.1 kips 50 KSI 100 KSI 28% 45% S9T-12-S42
(38 mm) (64 mm) (625 kN) (312 kN) (187 kN) (112 kN) (375 mPa) (670 mPa)
See notes at bottom

Stainless S-9 Undercut Concrete Anchor - ASTM A193 316 B8M Class II
Minimum Minimum Allowable Allowable
Bar Drill Hole Ultimate Yield Ultimate Elongation
in 4 Bar Reduction Partial Part
Strength Yield Tension Simple Shear Stress
Diameter Diameter Stress Diameters of Area Number
(FpuA) Strength .6 (FyA) .17 (FpuA) (1)
1/4" - 20 UNC 5/8” 3.50 kips 3.05 kips 1.83 kips 0.595 kips 96 KSI 110 KSI 15% 45% S9T-02-S62
(6.4 mm) (16 mm) (15.6 kN) (13.6 kN) (8.14 kN) (2.65 kN) (662 mPa) (759 mPa)
3/8” - 16 NC 7/8” 8.53 kips 7.44 kips 4.46 kips 1.45 kips 96 KSI 110 KSI 15% 45% S9T-03-S62
(9.5 mm) (22 mm) (37.9 kN) (33.1 kN) (20.0 kN) (6.45 kN) (662 mPa) (759 mPa)
1/2" - 13 UNC 7/8” 15.6 kips 13.6 kips 8.16 kips 2.65 kips 96 KSI 110 KSI 15% 45% S9T-04-S62
(13 mm) (22 mm) (69.4 kN) (60.6 kN) (36.3 kN) (11.8 kN) (662 mPa) (759 mPa)
5/8" - 11 UNC 1-1/8” 24.9 kips 21.7 kips 13.0 kips 4.23 kips 96 KSI 110 KSI 15% 45% S9T-05-S62
(16 mm) (29 mm) (110 kN) (96.5 kN) (57.8 kN) (18.8 kN) (662 mPa) (759 mPa)
3/4" - 10 UNC 1-1/8” 36.7 kips 32.1 kips 19.3 kips 6.24 kips 96 KSI 110 KSI 15% 45% S9T-06-S62
(19 mm) (29 mm) (163 kN) (143 kN) (85.8 kN) (27.8 kN) (662 mPa) (759 mPa)
1" - 8 UNC 1-5/8” 60.6 kips 48.5 kips 29.1 kips 10.3 kips 80 KSI 100 KSI 20% 45% S9T-08-S62
(25 mm) (41 mm) (269 kN) (216 kN) (129 kN) (45.8 kN) (552 mPa) (670 mPa)
1-1/4" - 7 UNC 2” 92.0 kips 63.0 kips 37.8 kips 15.8 kips 65 KSI 95 KSI 25% 45% S9T-10-S62
(32 mm) (51 mm) (409 kN) (280 kN) (168 kN) (70.3 kN) (448 mPa) (655 mPa)
1-1/2" - 6 NC 2-1/2” 126 kips 70.2 kips 42.1 kips 21.5 kips 50 KSI 90 KSI 30% 45% S9T-12-S62
(38 mm) (64 mm) (562 kN) (312 kN) (187 kN) (95.6 kN) (375 mPa) (621 mPa)
These loads are valid where embedment is sufficient to assure steel failure; that is concrete shear cone strength is greater than steel strength.
(1) Allowable Simple Shear load per AISC Table 1-D.
 S-9 Undercut Anchor Design Considerations
Williams has listed recommended embedment depths that are minimum values for ductile steel failure design in 3000
psi concrete. Embedment depths will need to increase according to the values determined from anchor design models
when spacing requirements are less than the values listed below (S). A reduction in anchor capacity should be used if
the concrete thickness does not allow for deeper embedments. Appropriate reduction factors can be calculated from
industry design models. When placing anchors that require a smaller edge distance than what is recommended in the
table below, the designer should be aware of a reduction in anchor capacity. Table information below can be used as a
reference when reduced edge distance is a factor in anchor design. The values for reduced edge distance are based
on tests in 3000 to 4000 psi non-reinforced concrete and should only be used as a reference in combination with reduc-
tion values calculated from industry design models.

Grade B7 S-9 Undercut Concrete Anchors - Minimum Spacing & Edge Distances

Concrete Failure Loads
Flush Center to Center Minimum
Bar Anchor Mount Embedment Attachment Spacing for Recommended Minimum 4 Bar ø 6 Bar ø 8 Bar ø
Ultimate
Diameter Length Anchor Depth Thickness Full Strength with Edge Distance Strength from the from the from the
Length no Reduction (S) (E) Edge (Test) Edge (Test) Edge (Test)
1/4” 4-1/2” 3” 1" 6” 3” 3.98 kips
- N.A. N.A. N.A.
(6.4 mm) (114 mm) (76 mm) (25 mm) (152 mm) (76 mm) (17.7 kN)
6” 3-3/4” 3-1/2” * 1"
(152 mm) (95 mm) (89 mm) (25 mm)
3/8” 8” 3-1/2” 3” 7” 5” 9.69 kips
- N.A. N.A. N.A.
(9.5 mm) (203 mm) (89 mm) (76 mm) (178 mm) (127 mm) (43.1 kN)
11” 6-1/2” 3”
-
(279 mm) (165 mm) (76 mm)
8” 5-5/8” 6” 1"
(203 mm) (143 mm) (152 mm) (25 mm)
1/2” 10” 6” 3” 12” 6” 17.7 kips 4 kips 8 kips 16 kips
-
(13 mm) (254 mm) (152 mm) (76 mm) (305 mm) (152 mm) (78.9 kN) (17.9 kN) (35.6 kN) (71.2 kN)
12” 8” 3”
-
(305 mm) (203 mm) (76 mm)
10” 7-1/8” 7-1/2” 1"
(254 mm) (181 mm) (191 mm) (25 mm)
5/8” 12” 7-1/2” 3” 15” 8” 28.2 kips 16 kips 29 kips
- N.A.
(16 mm) (305 mm) (191 mm) (76 mm) (381 mm) (203 mm) (125 kN) (71.2 kN) (129 kN)
15” 10” 3”
-
(381 mm) (254 mm) (76 mm)
13” 8-3/4” 9-1/4” 2”
(330 mm) (222 mm) (235 mm) (51 mm)
3/4” 16” 9-1/4” 5” 18-1/2” 11” 41.8 kips 20 kips 34 kips 41 kips
-
(19 mm) (406 mm) (235 mm) (127 mm) (470 mm) (279 mm) (187 kN) (89 kN) (151 kN) (182 kN)
19” 12-1/4” 5”
-
(483 mm) (311 mm) (127 mm)
17” 11-7/8” 12-1/2” 2”
(432 mm) (302 mm) (318 mm) (51 mm)
1" 20” 12-1/2” 5” 25” 14” 75.8 kips 25 kips 50 kips
- N.A.
(25 mm) (508 mm) (318 mm) (127 mm) (635 mm) (356 mm) (337 kN) (111 kN) (222 kN)
23” 15-1/2” 5”
-
(584 mm) (394 mm) (127 mm)
21” 15-1/4” 16” 2”
(533 mm) (387 mm) (406 mm) (51 mm)
1-1/4" 25” 16” 6” 32” 18” 121 kips 50 kips 90 kips 107 kips
-
(32 mm) (635 mm) (406 mm) (152 mm) (813 mm) (457 mm) (539 kN) (222 kN) (400 kN) (476 kN)
30” 21” 6”
-
(762 mm) (533 mm) (152 mm)
1-1/2” 31” 20-1/2” 21-1/2” 2” 43” 23” 176 kips N.A. N.A. N.A.
(38 mm) (787 mm) (520 mm) (546 mm) (51 mm) (1092 mm) (584 mm) (781 kN)
(N.A.) No test data available
Standard sizes are shown, special lengths available on request.
Tests were performed on A193 Grade B7 products and values will be conservative for Stainless Steel S-9 Anchors.
Concrete compressive strengths were between 3000-4000 psi unreinforced concrete.
Anchor embedment depth will vary with respect to anchor spacing.
Flush mount anchor length Includes coupling.
Attachment thickness for flush mount by others. Attachment bolt length or stud rod length are as required.
(*) 4-1/8” minimum embedment for flush mount.
 S-9 Undercut Anchor Installation
S9U Undercutting Tool
This tool is required for undercutting the holes to accommodate the S-9 Undercut Anchor. Designed to be attached
to concrete coring equipment and apparatus with water flushing capabilities. Specifications available on request.
Special length undercut tools can be manufactured upon request.

Typical Undercut Tools in Stock Torque Setting Chart

Standard Cone Revolutions
Bar Part Bar Distance per
Embedment Migration Required to Set
Diameter Number Diameter Revolution
Range into Shell Cone to Shell
1/4" - 20 UNC Up to 5” 1/4" - 20 UNC 0.4140” 0.0500”
S9U-02H 8 to 10
(6.4 mm) (127 mm) (6.4 mm) (10.52 mm) (1.27 mm)
3/8” - 16 NC Up to 6-1/2” 3/8” - 16 UNC 0.6040” 0.0625”
S9U-04H 9 to 11
(9.5 mm) (165 mm) (9.5 mm) (15.34 mm) (1.59 mm)
1/2" - 13 UNC Up to 8" 1/2" - 13 UNC 0.7191” 0.0769”
S9U-04H 9 to 11
(13 mm) (203 mm) (13 mm) (18.27 mm) (1.95 mm)
5/8" - 11 UNC Up to 10" 5/8" - 11 UNC 1.097” 0.0909”
S9U-06H 12 to 14
(16 mm) (254 mm) (16 mm) (27.86 mm) (2.31 mm)
3/4" - 10 UNC Up to 12-1/4" 3/4" - 10 UNC 1.189” 0.1000”
S9U-06H 11 to 13
(19 mm) (311 mm) (19 mm) (30.20 mm) (2.54 mm)
1" - 8 UNC Up to 15-1/2" 1" - 8 UNC 1.174” 0.1250”
S9U-08H 9 to 11
(25 mm) (394 mm) (25 mm) (29.82 mm) (3.18 mm)
1-1/4" - 7 UNC Up to 21" 1-1/4" - 7 UNC 1.622” 0.1428”
S9U-10H 11 to 13
(32 mm) (533 mm) (32 mm) (41.20 mm) (3.63 mm)
1-1/2" - 6 NC Up to 27-1/2" 1-1/2" - 6 NC 3.044” 0.1667”
S9U-12H 18 to 20
(38 mm) (699 mm) (38 mm) (77.32 mm) (4.23 mm)

S9T - A-193 B7 Bar - Torque Tension Chart

All data based on greased (MolyCoat Gn) threads and surfaces.
Larger diameter anchors
should be set and ten-
sioned using a hydraulic
test jack. See page 48.
Ft. - Lbs.

Ft. - Lbs.

Load in Kips.

Load in Kips
 S-9 Undercut Anchor Installation

Step 1 Step 2 Step 3

Before starting the undercutting procedure, Insert the tool into the hole until the bearing Turn the core drill handle downward with
be sure the hole is drilled to the proper diam- stop contacts the concrete. slow even motion until the cutter blades are
eter and depth (2 x bolt dia.). Attach the fully extended. The cutter blades are fully
undercutting tool to the core drill and be sure extended when the gap at the top between the
there is an adequate flow of water through the innershaft and outerhousing make contact.
tool.

Step 4 Step 5 Step 6

Conical shape is undercut with Williams Anchor and sleeve are inserted into hole. Anchor is jacked or torqued to draw the
Undercutting Tool attachment. cone up into the shell, therefore opening the
shell into the undercut hole.
 S-9 Undercut Flush Mount Anchor Installation
Williams also offers a flush mount S-9 Undercut Bearing Anchor that carries
all the advantages of the standard S-9 , but adds the ease of installing in special
conditions such as heavy machinery or large weldments. Refer to S-9 Undercut
Anchor Installation (page 24) for instructions on undercutting the drill hole, steps
1-4. After hole is undercut, proceed as shown below in steps 1-5.

Step 1 Step 2 Step 3

Attach expansion template and stud exten- Insert anchor set-up assembly into drill hole. Attach test coupling and test rod of center
sion to anchor. Check for proper anchor Set embedment to include expansion tem- hole test jack to stud extension. Tension to
embedment by measuring assembled set-up. plate. Template allows clearance for S-9 flush set anchor head to load specified for anchor.
mount coupling.

S-9 Flush Mount Undercut

Concrete Anchor Data
Anchor Minimum Offset Coupling
Size Embed. Dia. Length
3/8” 4-1/8” 3/8” 3/4" 2-1/4”
(9.5 mm) (105 mm) (9.5 mm) (19 mm) (57 mm)
1/2" 6” 3/8” 3/4" 2-1/4”
(13 mm) (152 mm) (9.5 mm) (19 mm) (57 mm)
5/8" 7-1/2” 3/8” 1" 3”
(16 mm) (191 mm) (9.5 mm) (25 mm) (76 mm)
3/4" 9-1/4” 1/2" 1-1/16” 3”
(19 mm) (235 mm) (13 mm) (27 mm) (76 mm)
1" 12-1/2” 5/8" 1-1/2" 4-1/4”
(25 mm) (318 mm) (16 mm) (38 mm) (108 mm)
1-1/4" 16” 3/4" 1-7/8” 5-5/8”
(32 mm) (406 mm) (19 mm) (48 mm) (143 mm)
Step 4 Step 5 1-1/2" 21-1/2” 1" 2-1/4” 8-5/8”
(38 mm) (546 mm) (25 mm) (57 mm) (219 mm)
Remove ram and setting tools and install After stud rods, bolts, washers or assem-
couple to offset per the following chart. blies are installed, torque hex nut to required
Anchor installation is complete and ready for tension or tension with hydraulic jack to work-
attachments. ing load.
 S-9 and S-7 Anchor Project Photos

Project: San Vicente Dam Raising Project: Popps Ferry Bridge Rehab
Contractor: Barnard Construction Contractor: Coastal Marine Contractors
Location: San Diego, CA Location: Biloxi, MS

Project: Seismic Retrofit TDOT Project: Pineview Dam

Contractor: St. Louis Bridge Contractor: Cal Wadsworth
Location: Tennessee Location: Ogden River, UT

Project: CSX Concrete Removal Project: CSX Concrete Removal

Contractor: Fenton Rigging Contractor: Fenton Rigging
Location: Benton Harbor, MI Location: Benton Harbor, MI
 S-7 Reusable Anchor System
The S-7 anchor consists of a reliable torque con-
trolled expansion anchor assembly similar to the Spin-
Lock, however the S-7 drill hole diameter is the same
size as the anchor stud diameter. This non-grouted
anchor system is easy for contractors to install and the
fast setting procedure saves time and money on impor-
tant anchor installations. S-7 anchors are ideal for con-
ditions that do not require cement grout as a corrosion
protection barrier and are generally specified as a multi-
purpose product with re-usable capabilities. The head
+<</6,5B
,8+<=<
+
0>55
E
,/+;371
+;/+


& 
+7-28;<
come complete with outer hex nut and washer. Zinc plat-
ing for corrosion protection is standard up to 1" diameter
bolts and optional on larger sizes. Anchors are also
available in stainless up to 1" in diameter.

S-7 Advantages
: Smaller drill holes
: Removable outer stud for reuse
: Field proven expansion anchor
: Convenient patching after removal
: Prestressable
: Anchor outer studs & heads can be purchased
separately

S-7 Reusable Concrete Anchor Studs

S-7 anchors are available with a variety of removable outer studs for special applications.
Type A - Typical for outer stud diameters over 1”.
Type B - For applications where a recessed, tapped hole is required. Type B anchors are usually flush with the concrete
surface and installed with a special Williams setting tool.
Type C - For stringing cable or wire though the anchor end. This anchor is often used for wire hangers or guy type
anchorages.
Type D - Typical for outer stud diameters of 1” or smaller. Outer stud end has flats which allow for easy anchor removal.
Type E - When type A, B, C or D anchor studs are removed, a type E stud can be used as a temporary hole plug. The
outer stud end has a notch to fit a flat head screwdriver.

Type A Type B Type C Type D Type E

 S-7 Reusable Anchor System

S-7 Reusable Concrete Anchor - Standard Carbon Steel Grade

Torque Ft.-Lbs. Minimum
Outer Maximum Allowable Cone Exterior
Embedment & Shell Overall Standard
Stud Allowable Ultimate Shear of Thread
in 3000 PSI Length Style Part
Diameter Working Load Strength Outer To Expand On Nut Length Length
Concrete (E) Number
(A) in Tension (1) Thread Shell for Tension (B) (C)
(D)
*4-1/4” - (108 mm)
1/2” - 13 3.13 kips 6.25 kips 1.6 kips 3-3/4” 1-1/4” 1-1/2”
15 30 5-1/2” - (140 mm) S7T-04
(13 mm) (14.0 kN) (27.8 kN) (7.1 kN) (95 mm) (32 mm) (38 mm)
7” - (178 mm)
*5-3/4” - (146 mm)
3/4” - 10 8.5 kips 17 kips 3.9 kips 5-1/4” 1-3/4” 1-3/4” 7” - (178 mm)
70 100 S7T-06
(19 mm) (37.8 kN) (75.6 kN) (17.3 kN) (133 mm) (45 mm) (45 mm) 8-1/2” - (216 mm)
10” - (254 mm)
*7-3/4” - (197 mm)
1” - 8 11.25 kips 22.5 kips 7.2 kips 7-1/4” 2-9/16” 2-1/2”
85 200 9” - (229 mm) S7T-08
(25 mm) (50 kN) (100 kN) (32.0 kN) (184 mm) (65 mm) (64 mm)
12” - (305 mm)
1-1/4” - 7 11.25 kips 22.5 kips 11.5 kips 7-3/4” 3-1/4” 3-1/4” *9” - (229 mm)
125 240 S7T-10
(32 mm) (50 kN) (100 kN) (51.1 kN) (197 mm) (83 mm) (83 mm) 12” - (305 mm)
1-3/4” - 5 37.5 kips 75 kips 22.6 kips 12-1/2” 6-1/4” 4” *15” - (381 mm)
500 900 S7T-14
(45 mm) (167 kN) (334 kN) (101 kN) (318 mm) (159 mm) (102 mm) 18” - (457 mm)
2” - 6 60 kips 120 kips 31.5 kips 16” 6-3/4” 4” *18” - (457 mm)
500 1,500 S7T-16
(51 mm) (267 kN) (534 kN) (140 kN) (406 mm) (171 mm) (102 mm) 24” - (610 mm)
(1) Maximum recommended working load is based on 1/2 of ultimate strength.
* Recommended for type B only, to achieve full embedment.

Stainless S-7 Reusable Concrete Anchor - ASTM A193 (304) B8 Class 1

Torque Ft.-Lbs. Minimum
Outer Maximum Allowable Cone Exterior
Embedment & Shell Standard
Stud Allowable Ultimate Shear of Thread E
in 3000 PSI Style Part
Diameter Working Load Strength Outer To Expand On Nut Length Length Overall Length
Concrete Number
(A) in Tension (1) Thread Shell for Tension (B) (C)
(D)
*4-1/4” - (108 mm)
1/2” - 13 .943 kips 3.93 kips 1.81 kips 3-3/4” 1-1/4” 1-1/2”
10 10 5-1/2” - (140 mm) S7U-3041-04
(13 mm) (4.2 kN) (17.5 kN) (8.0 kN) (95 mm) (32 mm) (38 mm)
7” - (178 mm)
*5-3/4” - (146 mm)
3/4” - 10 2.55 kips 10.64 kips 4.26 kips 5-1/4” 1-3/4” 1-3/4” 7” - (178 mm)
50 60
(19 mm) (11.4 kN) (47.3 kN) (18.9 kN) (133 mm) (45 mm) (45 mm) 8-1/2” - (216 mm) S7U-3041-06
10” - (254 mm)
*7-3/4” - (197 mm)
1” - 8 4.07 kips 16.95 kips 7.73 kips 7-1/4” 2-9/16” 2-1/2”
75 170 9” - (229 mm) S7U-3041-08
(25 mm) (18.1 kN) (75.4 kN) (34.4 kN) (184 mm) (65 mm) (64 mm)
12” - (305 mm)
(1) Maximum recommended working load is based on .6 of yield strength.
* Recommended for type B only, to achieve full embedment.
 S-7 Design Considerations
Williams has listed recommended embedment depths that are minimum values for ductile steel failure design in 3000
psi concrete. Embedment depths will need to increase according to the values determined from anchor design models
when spacing requirements are less than the values listed below (S). A reduction in anchor capacity should be used if
the concrete thickness does not allow for deeper embedments. Appropriate reduction factors can be calculated from
industry design models. When placing anchors that require a smaller edge distance than what is recommended in the
table below, the designer should be aware of a reduction in anchor capacity. Table information below can be used as a
reference when reduced edge distance is a factor in anchor design. The values for reduced edge distance are based
on tests in 3000 to 4000 psi non-reinforced concrete and should only be used as a reference in combination with reduc-
tion values calculated from industry design models.
S-7 Reusable Anchor - Minimum Spacing & Edge Distance
Minimum Center to Center Minimum Minimum Concrete Failure Loads
Outer Embedment Spacing for Full Recommended Ultimate 4 Bar ø 6 Bar ø
Stud in 3000 PSI Strength with no Edge Distance Strength of from the Edge from the Edge
Diameter Concrete Reduction (S) (E) Inner Stud (Test) (Test)
1/2” - 13 3-3/4” 7-1/2” 5” 6.25 kips 4 kips 6.2 kips
(13 mm) (95 mm) (191 mm) (127 mm) (27.8 kN) (18 kN) (31 kN)
3/4” - 10 5-1/4” 10-1/2” 5-3/4” 17 kips 11 kips 17 kips
(19 mm) (133 mm) (267 mm) (146 mm) (75.6 kN) (49 kN) (76 kN)
1” - 8 7-1/4” 14-1/2” 9” 22.5 kips 15 kips 22 kips
(25 mm) (184 mm) (368 mm) (229 mm) (100 kN) (67 kN) (98 kN)
1-1/4” - 7 7-3/4” 15-1/2” 12-1/2” 22.5 kips 19 kips 21 kips
(32 mm) (197 mm) (394 mm) (318 mm) (100 kN) (85 kN) (93 kN)
1-3/4” - 5 12-1/2” 25” 16” 75 kips 18 kips 23 kips
(45 mm) (318 mm) (635 mm) (406 mm) (334 kN) (80 kN) (102 kN)
2” - 6 16” 32” 21” 135 kips N.A. N.A.
(51 mm) (406 mm) (813 mm) (533 mm) (600 kN)
(N.A.) No test data available
Recommended safe edge distance to be at least 10 bar diameters.
Concrete compressive strengths were between 3000-4000 psi unreinforced concrete.

Materials
The Williams S-7 Reusable Concrete Anchor is offered in diameters ranging from 1/2"-13 UN thru 2"-6 UN and a
choice of materials including ASTM A108 standard commercial grade carbon steel and ASTM A193 Grade B8 Type 304
stainless steels in anchor sizes up to 1” diameter. The anchors shall be complete with stud, cone, and expansion shell.
1. Anchor assembly for S-7 consists of:
a. An anchor stud complying with ASTM A108 for carbon steel and ASTM A193 Grade B8 Type 304 for stainless
steel.
b. A Williams cone in threaded engagement with the inner end of the anchor stud complying with ASTM A 29 for
carbon steel and ASTM A193 Grade B8 Type 304 for stainless steel. The cone shall have an exterior conical
surface continuous in cross section to deliver bearing pressure radially with respect to the axis of the anchor bar.
c. A Williams slotted expansion shell with an inner surface bearing on the cone, the outer surface initially of
cylindrical curvature. The steel complies with ASTM A108 for carbon steel and ASTM A193 Grade B8 Type 304
for stainless steel.
2. The S97 Setting Tool is required for installation of S-7 Reusable Concrete Anchors.

Cone Shell Inner Stud Outer Stud (Type A)

Williams S-7 anchors are specially designed with a cone that threads into the bottom of the anchor stud. This thread-
ed portion at the bottom of the anchor governs the ultimate tensile capacity of the system, which explains why the ten-
sile loads are lower than Williams Spin-Lock anchor systems. However, shear loading at the base plate is resisted by
the full diameter of the anchor stud rather than the smaller threaded diameter at the cone/stud interface. The picture
above illustrates this point. This process is necessary to provide the user with a reusable detachable anchor stud. The
outer stud diameter dictates the shear strength of the anchor, while the inner stud diameter dictates the anchor tensile
strength.
 S-7 Anchor Applications
The S-7's unique design allows the hole to be drilled and the bolt to be placed through an existing plate, tower base
or machine base when required. In a temporary bolting situation, the outer portion of the bolt may be removed and dis-
carded or reused once the anchor is no longer needed. Since it is unnecessary to pull out or burn off unwanted anchors,
patching operations are quick and clean.
Pipe Supports or Temporary Tie Down Anchors for
Electrical Tray Hangers Aircraft & Inflatable Structure Covers

Removable Machinery Anchor S-7 Form Tie

 S-7 Reusable Anchor Installation
Step 1 Step 2
Drill hole diameter to equal Install setting tool on S-7
nominal bolt diameter. anchor and tap with ham-
Holes in concrete should be mer into hole. If the anchor
two times the bolt diameter goes into the hole extreme-
deeper than the embed- ly loose, remove the anchor
ment length. from the hole. Pre-expand
the anchor head one half
revolution or until it fits
snugly into the drill hole.

Step 3 Step 4
Torque the anchor bolt Remove setting tool. If the
clockwise to indicated ft.-lb. setting tool does not imme-
for expanding the anchor diately remove, use a
head. wrench to back off hex bolt
in the setting tool. Install
plate, washer, and nut.

Step 5 S9Z S-7 Setting Tool

Torque nut to indicated ft.- Included with
Bar Part
lb. for pretension. The stud Diameter Number each full box of
portion of the S-7 may be 1/2" S9Z-004 anchors up to 1” in
removed and reattached 3/4" S9Z-006
diameter. For
when required. 1" S9Z-008
1-1/4" S6Z-OH-010 anchors above 1”
1-3/4" S6Z-OH-014 in diameter, use
2" S6Z-OH-016 S6Z Spin-Lock
Setting Tool.

Demonstration of S-7 Removable Use

 Sledge Drive Anchors
Quick, simple anchor designed to develop the full strength of the bar. Recommended for short anchors in rock or
concrete. Available with 1-5/8” diamenter aluminum expansion shell. In temporary situations, bar may be removed and
used again. Williams can supply custom length steel drive pipes at your request.
0
d R5 ar
Ro o r b
th S od 75 d Re
m oo B7 oil R d e a
S th ra hre
B1
S Wi ad C 1 G
l- T
th hr
e R6 0 Al
Wi l - T t h
Wi de
6
Al a
Gr

Recommended Embedment Depth Minimum Edge Distance

Average Part Number
Stee Bar Safe Working Drill
Ultimate B8S Cone / Shell
Type Diameter Load to 2:1 Hole 3000 PSI 5000 PSI 3000 PSI 5000 PSI
Strength (B7S Cone / Shell)
Safety Factor Concrete Concrete Concrete Concrete
3/8" 4.9 kips 9.8 kips 1-5/8" 6” 5” 4.8” 4.2” R4M03RB0 / R4A13
B1S (9.5 mm) (21.8 kN) (43.6 kN) (41 mm) (152 mm) (127 mm) (122 mm) (107 mm) (R4MC3RB0 / R4A13)
Smooth Rod 1/2" 9 kips 18 kips 1-5/8" 7” 6” 6.4” 5.6” R4M04RB0 / R4A13
(13 mm) (40.0 kN) (80.1 kN) (41 mm) (178 mm) (152 mm) (163 mm) (142 mm) (R4MC4RB0 / R4A13)
B7S 5/8" 11.3 kips 22.5 kips 1-5/8" 8” 7” 7.7” 6.7” R4M05RB0 / R4A13
All-Thread Coil Rod (16 mm) (40.0 kN) (100 kN) (41 mm) (203 mm) (178 mm) (196 mm) (170 mm) (R4MC5RB0 / R4A13)
3/4" 18 kips 36 kips 1-5/8" 10” 9” 9.2” 8.1” R4M06RAC / R4A13
B8S (19 mm) (80.0 kN) (160 kN) (41 mm) (254 mm) (228 mm) (234 mm) (206 mm) (R4MC6RAC / R4A13)
All-Thread N.C. Rod 7/8" 29 kips 58 kips 1-5/8" 12” 11” 11.4” 10” R4M07RAC / R4A13
(22 mm) (129 kN) (258 kN) (41 mm) (305 mm) (279 mm) (290 mm) (254 mm) (R4MC7RAC / R4A13)
#4 - 1/2" 9 kips 18 kips 1-5/8" 7” 6” 6.4” 5.6”
R4MG4RAC / R4A13
R50 Grade 60 (13 mm) (40 kN) (80.1 kN) (41 mm) (178 mm) (152 mm) (163 mm) (142 mm)
All-Thread Rebar #5 - 5/8" 13.8 kips 27.9 kips 1-5/8" 9” 8” 8” 7”
R4MG5RAC / R4A13
(16 mm) (62 kN) (124 kN) (41 mm) (228 mm) (203 mm) (203 mm) (178 mm)
R61 Grade 75 #6 - 3/4" 22 kips 44 kips 1-5/8" 11” 10” 10” 9”
R4MG6RAC / R4A13
All-Thread Rebar (19 mm) (97.9 kN) (196 kN) (41 mm) (279 mm) (254 mm) (254 mm) (228 mm)

Sledge Drive Anchor Installation

Drill hole to prescribed Insert Sledge Drive Place heavy wall pipe Attach item to be
diameter and exact Anchor to bottom of hole. driver over bar and drive anchored or plate and
embedment depth for Bolt may be tapped in shell down over cone to nut. Anchor may be pre-
rock bolt. place. expand anchor. stressed or pre-tested.
 Epoxy Anchor System
When are Epoxy Concrete Anchors used?
E Epoxy concrete anchors are an excellent alternate to Williams high capacity mechanical anchors when applica-
tions require close anchor spacing and small edge distances. Mechanical anchors require greater spacings
and edge distances because of the lateral pressure placed on the drill hole due to anchor expansion. This expan-
sion pressure is reduced with epoxy anchor systems.
E Epoxy is ideal for passive dowels or anchors without a prestress load, however when high capacity anchors
are to be prestressed the designer should consider Williams Spin-Lock mechanical anchors.
E Use Williams epoxy anchors for concrete anchors loaded in shear.
Applications
E
Concrete Foundation Repair
E
Seismic Retro-Fit
E
Machinery Anchoring
E
Anchors for Rail Systems
E
Underwater Doweling
E
Concrete Dock Repair and Construction
E
Anchors subject to large shear loads
E
Bridge Pier Reinforcement
E
Pier Cap Repairs
E
Dam Refacement
E
General Plant Maintenance
E
Column Anchors
E
Light Poles
Approvals and Listings
ICC (formerly ICBO) ER Evaluation Report #4996
State DOT’s
Ultrabond products meet the new ICC AC58 Acceptance Criteria for Adhesive Anchors in Concrete and Masonry
Elements. This testing criteria was developed at the request of ICC and engineers throughout the United States in order
to evaluate the long term performance and durability of various epoxy systems under real world conditions.

Ultrabond 1 Ultrabond 1 Ultrabond 2 Ultrabond 2

22 oz. Cartridge 53 oz. Cartridge 22 oz. Cartridge 53 oz. Cartridge

Grade 75 All-Thread Rebar

Manual Epoxy Dispenser

(A Pneumatic Epoxy Dispenser is avail-
able for the 53 oz cartridge.
Mixing Nozzle
 Ultrabond Epoxy Technical Information
Shelf Life 28 Months The Ultrabond Epoxy Anchor System is a two
Storage Room Temperature out of direct sunlight component 100% solids, high aspect ceramic blend
Application Temperature Range* 35° - 115° F amine-based epoxy. It is a solvent free, high
Resin - White strength, high modulus, moisture insensitive, non-
Color Hardener - Black sag epoxy system.
Mixed - Concrete Grey
Resin - 330,000 cps
Viscosity
Hardener - 150,000 cps
*Temperature application range or product information range refers to the temperature range that the product is recommended for use.
The product will need to be warmed prior to use at temperatures below 70° F.

Ultrabond 1 Properties Ultrabond 2 Properties

Gel Time (60g @ 75° F) 20 minutes Gel Time (60g @ 75° F) 25 minutes
Cure Time (60g @ 75° F) 4 hours Cure Time (60g @ 75° F) 10 hours
Final Cure (60g @ 75° F) 24 hours Final Cure (60g @ 75° F) 48 hours
Linear Shrinkage 0.003 cm/cm Water Absorption - 24 hrs 0.40%
Compressive Yield Strength - 7 days 9,880 psi Linear Shrinkage 0.002 cm/cm
Compressive Modulus Strength - 7 days 191,280 psi Compressive Yield Strength - 7 days 10,850 psi
Tensile Strength - 7 days 6,790 psi Compressive Modulus Strength - 7 days 210,800 psi
Elongation at Break - 7 days 1.9% Tensile Strength - 7 days 7,190 psi
Heat Deflection Temperature L

L
 Elongation at Break - 7 days 1.9%
Bond Strength - 2 days 1,100 psi Heat Deflection Temperature L

L

Bond Strength - 14 days 1,640 psi Bond Strength - 2 days 1,280 psi
Bond Strength - 14 days 1,740 psi

Ultrabond 1 Temp vs Bolt-Up Times Ultrabond 2 Temp vs Bolt-Up Times

Temperature Bolt-Up Time* Final Cure Time* Temperature Bolt-Up Time* Final Cure Time*
L

L
 3 Hrs. 20 Hrs. L

L
 8 Hrs. 44 Hrs.
 L

L
 4 Hrs. 24 Hrs.  L

L
 10 Hrs. 48 Hrs.
L

L
 8 Hrs. 42 Hrs. L

L
 20 Hrs. 72 Hrs.
 L

 L
 16 Hrs. 56 Hrs.  L

 L
 24 Hrs. 96 Hrs.
L

L
 24 Hrs. 72 Hrs. L

L
 48 Hrs. 144 Hrs.
*Bolt-Up Time and Final Cure Time is based off the lowest substrate temperature experienced during the curing. Therefore, if the lowest temperature
2E=2?62;02
/F
A52
@B/@A?.A2
6@
 L

 L

A52;
6A
D699
A.82

5<B?@
3<?
,9A?./<;1

A<
0B?2

AC58 Test Criteria - The International Code Council (ICC) developed this adhesive test criteria because they recog-
nized the necessity for engineers and contractors to be able to distinguish between poor, medium and high quality adhe-
sives. The long term durability of the adhesive, in a variety of service conditions, is of particular importance. We are
proud to say Ultrabond demonstrates superiority and easily passes all of the service condition tests. The following data
substantiates Ultra-Bond’s exceptional performance.
In-Service Temperature - Test shows the strength of the anchoring systems in elevated temperatures. The following
charts show the strength of Ultrabond 1 & 2 load values versus temperature.

Ultrabond 1 In-Service Temperature Ultrabond 2 In-Service Temperature

% Load

% Load

Temperature (°F) Temperature (°F)

Creep - This test simulates epoxy performance for 30 to 50 years of service life. Ultrabond 1 passed this test with a
10,500 lbs. tensile load on a 1/2” diameter anchor.
Dampness - This test shows the hole may be damp during installation. Therefore, if the construction site is exposed to
a damp environment, Ultrabond can be used without compromising the strength (rain, rivers, lakes, water treatment
plants, ect.).
Seismic - This test shows the anchor system can withstand seismic activity, wind loading, and cyclic loading. Both
Ultra-Bond products passed this test with a 10,000 lbs. tensile load on a 1/2” diameter anchor.
Freezing & Thawing - This test shows the anchor can withstand freezing and thawing climates. This is very important
in environments that experience an annual winter that goes below freezing.
 Epoxy Anchor Bar Strength Charts
Williams All-Thread-Bars are used with the Ultrabond adhesive for unmatched anchoring versatility and capacities. The
Ultrabond adhesive provides a molecular bond to the substrate while coating and protecting the embedded dowel. The epoxy
distributes the transmitted load from the dowel into the concrete over the entire surface of the anchor hole. Since the epoxy
is stronger than the concrete, the ultimate anchor load will be limited only by the concrete or capacity of the steel. Bars can
be ordered cut to length or in stock lengths up to 50 feet for job-site cutting. The 360° thread provides unmatched epoxy to
bar bond. Williams offers hex nuts, plates and washers with each anchor bar. Working loads should be based on a 4:1 safe-
ty factor from bar ultimate strength. Listed anchor embedment depth based on 3,000 PSI concrete. Williams recommends
epoxy dowels to only be specified as passive (non-prestressed) anchors. Williams bars should never be torch cut.

R71 150 KSI All-Thread-Bar - ASTM A722-98

Minimum Minimum Working Approx. Recommended Quantity of Recommended
Bar Ultimate Yield Load Thread Ultrabond Hole Diameter
Diameter Embedment
Strength Strength (4:1 SF) Major Dia. per Hole
1" 127.5 kips 102 kips 31 kips 1-1/8" 25” 4.5 oz 1-1/4”
(25 mm) (567 kN) (454 kN) (137 kN) (28.6 mm) (630 mm) (8.2 in3) (32 mm)
1-1/4" 187.5 kips 150 kips 46 kips 1-7/16" 29” 11.9 oz 1-5/8”
(32 mm) (834 kN) (667 kN) (201 kN) (36.5 mm) (730 mm) (21.5 in3) (41 mm)
1-3/8" 237 kips 190 kips 59 kips 1-9/16" 33” 13.3 oz 1-3/4”
(36 mm) (1054 kN) (843 kN) (255 kN) (39.7 mm) (840 mm) (23.9 in3) (45 mm)
1-3/4" 400 kips 320 kips 100 kips 2" 44” 32.5 oz 2-1/4”
(45 mm) (1779 kN) (1423 kN) (430 kN) (50.8 mm) (1100 mm) (58.7 in3) (57 mm)

R61 Grade 75 All-Thread Rebar - ASTM A615

Bar Minimum Minimum Working Approx. Recommended Quantity of Recommended
Designation Ultimate Yield Load Thread Ultrabond Hole Diameter
Embedment
Nominal Dia. Strength Strength (4:1 SF) Major Dia. per Hole
#6 - 3/4" 44 kips 33 kips 11 kips 7/8" 12” 2.4 oz 1"
(19 mm) (196 kN) (147 kN) (48 kN) (22 mm) (310 mm) (4.4 in3) (25 mm)
#7 - 7/8" 60 kips 45 kips 15 kips 1" 15” 3.4 oz 1-1/8"
(22 mm) (267 kN) (200 kN) (66 kN) (25 mm) (270 mm) (6.2 in3) (28 mm)
#8 - 1" 79 kips 59.3 kips 19 kips 1-1/8" 17” 4.4 oz 1-1/4”
(25 mm) (351 kN) (264 kN) (87 kN) (28 mm) (430 mm) (7.9 in3) (32 mm)
#9 - 1-1/8" 100 kips 75 kips 25 kips 1-1/4" 20” 5.4 oz 1-3/8"
(28 mm) (445 kN) (334 kN) (111 kN) (32 mm) (490 mm) (9.5 in3) (35 mm)
#10 - 1-1/4" 127 kips 95.3 kips 31 kips 1-3/8" 21” 10.4 oz 1-5/8”
(32 mm) (565 kN) (424 kN) (141 kN) (35 mm) (540 mm) (18.8 in3) (41 mm)
#11 - 1-3/8" 156 kips 117 kips 39 kips 1-1/2" 24” 12.0 oz 1-3/4”
(35 mm) (694 kN) (521 kN) (173 kN) (38 mm) (610 mm) (21.7 in3) (45 mm)
#14 - 1-3/4" 225 kips 168.7 kips 56 kips 1-7/8" 29” 21.4 oz 2-1/8”
(45 mm) (1001 kN) (750 kN) (250 kN) (48 mm) (730 mm) (38.7 in3) (55 mm)
#18 - 2-1/4" 400 kips 300 kips 100 kips 2-7/16" 39” 43.1 oz 2-3/4”
(55 mm) (1779 kN) (1335 kN) (444 kN) (62 mm) (980 mm) (77.9 in3) (70 mm)

B8V High Impact Bar - ASTM A193 - Grade B7

Minimum Minimum Working Approx. Recommended Quantity of Recommended
Bar Ultimate Yield Load Thread Ultrabond Hole Diameter
Diameter Embedment
Strength Strength (4:1 SF) Major Dia. per Hole
1/2" - 13 UNC 18 kips 15 kips 4.5 kips 1/2" 4-1/2” 0.2 oz 9/16”
(13 mm) (80 kN) (66.7 kN) (20.0 kN) (13 mm) (114 mm) (0.3 in3) (14.3 mm)
5/8" - 11 UNC 29 kips 24 kips 7.25 kips 5/8" 5-5/8” 0.55 oz 3/4”
(16 mm) (129 kN) (108 kN) (32.2 kN) (16 mm) (143 mm) (1 in3) (19 mm)
3/4" - 10 UNC 42 kips 36 kips 10.25 kips 3/4" 6-3/4” 0.71 oz 7/8”
(19 mm) (187 kN) (160 kN) (45.6 kN) (19 mm) (171 mm) (1.3 in3) (22 mm)
7/8" - 9 UNC 58 kips 49 kips 14.5 kips 7/8" 16” 2.0 oz 1"
(22 mm) (258 kN) (218 kN) (64.5 kN) (22 mm) (406 mm) (3.7 in3) (25 mm)
1" - 8 UNC 76 kips 64 kips 19 kips 1" 20” 2.8 oz 1-1/8"
(25 mm) (338 kN) (285 kN) (84.5 kN) (25 mm) (508 mm) (5.2 in3) (29 mm)
1-1/8" - 7 UNC 96 kips 81 kips 24 kips 1-1/8" 22” 3.5 oz 1-1/4"
(29 mm) (427 kN) (360 kN) (107 kN) (28 mm) (559 mm) 6.4 in3) (32 mm)
1-1/4" - 7 UNC 122 kips 102 kips 30.5 kips 1-1/4" 25” 4.5 oz 1-3/8”
(32 mm) (543 kN) (454 kN) (136 kN) (32 mm) (635 mm) (8.3 in3) (35 mm)
1-3/8” - 8 UN 154 kips 129 kips 38.5 kips 1-3/8" 28” 11.0 oz 1-5/8”
(35 mm) (684 kN) (573 kN) (171 kN) (35 mm) (711 mm) (20.2 in3) (41 mm)
1-1/2" - 6 NC 176 kips 148 kips 44 kips 1-1/2" 29” 12.5 oz 1-3/4"
(38 mm) (783 kN) (658 kN) (197 kN) (38 mm) (737 mm) (23.0 in3) (45 mm)
1-3/4" - 5 UNC 237 kips 199 kips 59.3 kips 1-3/4" 34” 17.1 oz 2"
(45 mm) (1054 kN) (885 kN) (264 kN) (45 mm) (864 mm) (31.3 in3) (51 mm)
2" - 6 UN 330 kips 278 kips 82.5 kips 2" 43” 24.4 oz 2-1/4”
(51 mm) (1467 kN) (1236 kN) (367 kN) (51 mm) (1092 mm) (44.8 in3) (57 mm)
 Epoxy Anchor Design Considerations
Ultrabond adhesive is a two component 100% solid, high aspect ceramic blend epoxy. They consist of a resin and a
curing agent Adhesive anchors are often used because of fast curing times compared to cement based grouts. The
Ultrabond adhesive, after being properly mixed through the mixing nozzle, experiences an exothermic reaction which
forms a polymer matrix bonding to the surrounding concrete. The bond generated by the Ultrabond adhesive is accom-
plished through a dual action of chemically adhering to the concrete and by interlocking with drill hole surface deforma-
tions. When designing adhesive anchor systems the engineer should be aware of four potential failure modes; ductile
steel failure, concrete breakout, bond failure between the adhesive and the steel threads and bond failure between the
concrete and epoxy interface. Presently the anchor industry is absent of a formal design code for adhesive anchors,
however the designer can consider the following equations for assistance.
Uniform Bond Stress Model = Bond Strength (lbs)
= <;1
*A?2@@
/.@21
<;
0B?2
A6:2@
.A
 L

= 1600 psi in 14 days - ASTM C882
= 1100 psi in 2 days - ASTM C882
= 3.14 Based on normal
= Drill Hole Diameter (in.) weight concrete
= Anchor Embedment Depth (in.)
Concrete Breakout Strength
A designer can estimate the concrete capacity using methods such as ACI 349-97 Appendix B or ACI 318-02
Appendix D. Example:
= Concrete Capacity (lbs)
= Concrete Compressive Strength (psi)
2 2
= ( ) = Projected Cone Area (in )
= Anchor Embedment Depth (in)
Williams recommends designing for ductile steel failure whenever possible. Steel strengths can be collected from the
strength charts. The designer can verify concrete capacity and bond strengths from the equations listed above to deter-
mine which are the governing factors.

Epoxy Anchor Applications

Typical
Masonry
Application

Rebar Extensions Underwater Locations

 Epoxy Anchor Installation
Job-Site Preparation and Work Flow
To achieve the desired results, carefully follow these pro-
cedures. If installing anchors in extreme temperatures
please call your local Williams representative.
I
9D.F@
/2
@B?2
A52
5<92@
.?2
=?2=.?21
6;
.1C.;02
before starting a new cartridge. If possible, schedule dis-
pensing to consume an entire cartridge at one time with
no interruption of epoxy flow.
The "HP" Nozzle breaks off to accommodate varying hole diameters and depths. I
+<
.0562C2
:.[Link]
39<D
.;1
?21B02
3.A64B2
/?2.8
<33
the nozzle to the largest diameter that will fit into the hole
or screen. If the hole is 5/8" diameter or larger, snap off
the smaller diameter section before using.

Dual Cartridge Anchoring & Doweling Into Concrete

1. Drill hole to proper diam- 2. Insert cartridge into the

eter and depth. Blow out gun with label side down.
dust from the bottom of the This allows you to see how
hole. Brush the hole with a much material is left in the
nylon brush. Blow out dust cartridge.
again. The hole should be
dry and clean of dust and
debris.

3. Remove plastic band and 4. Thread nozzle onto car-

black caps from the car- tridge, making sure the noz-
tridge. Dispense a small zle, and cartridge assembly
amount of epoxy into a are secure. Dispense
disposable container until enough epoxy into a dispos-
you get an even flow of able container, until the
black and white material. color becomes a consistent
gray with no streaks.

5. Dispense the material 6. Insert the threaded bar or

from the bottom of the hole. rebar to the bottom of the
Fill approximately 1/4 of the hole while turning bar into
hole depth while slowly epoxy. The threaded bar or
withdrawing the nozzle. rebar should be free of dirt,
grease, oil, or other foreign
materials. Do not disturb or
bolt-up until minimum bolt-
up time has passed.
 Cast-in-Place Concrete Anchors
Williams Form Engineering can supply a wide range of cast-in-place concrete anchor systems. Ranging from J, U
and L-Bolts to a special post-tensionable anchor system that Williams has used on several high profile projects. Anchor
design criterea for cast-in-place anchors can be found in ACI 318 Appendix D.

Cast-in-Place Post-Tensionable System

The system shown below allows the engineer to design an anchor system that can be cast-in-place and after the con-
crete sets, the anchor can be prestressed. The bond breaker provides a free stress length commonly used in post-ten-
sioning systems. The free stress length helps to prevent load loss and concrete spalling that can eventually lead to cor-
rosion problems or fatigue failure. After the anchor is prestressed, the inside of the sleeve can be grouted or it can be
pre-greased with a corrosion inhibiting product prior to anchor placement. Bar strengths are listed on pages 42-45.

Project: Fjardaal Smelting Plant Project: London Lock & Dam Rehabilitation

Contractor: Bechtel Overseas Corp. Contractor: OCCI Inc.
Location: Iceland Location: London, WV
 Cast-in-Place Concrete Anchors
B5S Stress Gradient Pigtail Anchor - C1045 Steel
Williams patented Stress Gradient Pigtail Anchor has a unique design, which gradually increases the depth of each
crimp to develop a full length Pigtail anchor. The lesser crimps in front allow the Pigtail to elongate through the concrete
thereby transferring stress over its entire length. The stress gradient anchor is a positive "non-slip" anchor, which may
be placed within 3" of an edge even in low compression strength concrete.
Williams combines the extra strength of stress gradient Pigtail anchors with high tensile 120 KSI steel for more
strength per pound than mild steel. A 1/2" high tensile bar will do the work of a 5/8"
mild steel bar. Always remember the anchors should be set during
pour and no later than one hour after completion of
the pour. Work concrete well around
When using Williams Pigtail when placing.
Stress Gradient Pigtail Anchors, the following
factual advantages are accomplished: 1) Maximum embed-
ment of the Pigtail Anchor is achieved, 2) The stress gradient crimp pattern
deforms the steel for excellent bonding strength, and 3) The high tensile steel offers high work-
ing loads with no welds which can limit strength.
B5S Stress Gradient Pigtail Anchor
Standard Lengths Radiused Lengths Safe Working
Ultimate
Total C Load
Diameter A B Strength
Length Total Length (2:1 S.F.)
3/8” - 8 NC 12” 4” 10” 22” 4.9 kips 9.8 kips
(9.5 mm) (305 mm) (102 mm) (254 mm) (559 mm) (21.8 kN) (43.6 kN)
1/2" - 13 UNC 18” 4” 10” 24” 8.53 kips 17.1 kips
(13 mm) (457 mm) (102 mm) (254 mm) (610 mm) (37.9 kN) (75.8 kN) A
5/8" - 11 UNC 24” 6” 12” 30” 13.6 kips 27.1 kips
(16 mm) (610 mm) (152 mm) (305 mm) (762 mm) (60.3 kN) (120.6 kN)
3/4" - 10 UNC 24” 6” 12” 30” 20.1 kips 40.1 kips Radiused Pigtail
(19 mm) (610 mm) (152 mm) (305 mm) (762 mm) (89.2 kN) (178 kN)
7/8" - 9 UNC 30” 8” 14” 36” 27.7 kips 55.4 kips B
(22 mm) (762 mm) (203 mm) (356 mm) (914 mm) (123 kN) (246 kN)
1" - 8 UNC 36” 8” 14” 42” 36.4 kips 72.7 kips
(25 mm) (914 mm) (203 mm) (356 mm) (1067 mm) (162 kN) (323 kN)
1-1/8" - 7 UNC 36” 40.5 kips 81 kips
N.A. N.A. N.A.
(29 mm) (914 mm) (180 kN) (360 kN)
1-1/4" - 7 UNC 42” 51 kips 102 kips
N.A. N.A. N.A.
(32 mm) (1067 mm) (254 kN) (508 kN)
2" - 6 UN 72” 139 kips 279 kips
N.A. N.A. N.A.
(51 mm) (1829 mm) (657 kN) (1313 kN)
Pigtail lengths shown are recommended for 3000 PSI concrete or better. N.A. = Not Available

B3Z Column Anchor

Williams B3Z Column Anchor was designed for use in most general construction, specifically machine, col-
umn or utility pole anchoring. The two-piece feature gives this anchor the ability to be placed flush with the
concrete, therefore, eliminating interference during concrete placement and finishing. The anchor stud can
then be conveniently threaded into the replaced anchor assembly as needed. Williams Column Anchor studs
and bars are fabricated from ASTM A108 cold rolled C-1045 steel with a high tensile strength. Couplings are
designed to exceed bar strengths. Anchors are available in most diameters. Plastic caps are provided to pro-
tect the threads during concrete pouring.

A
A

B B
B4S J-Bolts B3S L-Bolts
Round or square bottom J-bolts with most length and May be used as embedded anchor bolts. Available in
radius combinations available for a wide range of appli- most diameters with coil or V-thread. To order, please
cations. Available in most diameters with coil or V- specify diameter, A and B dimensions, thread type and
thread. To order, please specify diameter, A and B length.
dimensions, thread type and length.
 Grout Bonded Concrete Anchors
William's grouted concrete anchors are post-installed bars utilizing a high strength grout for the bonding material. The
advantage of using a grout versus and epoxy is cement grout does not break down in high heat areas and can be
pumped into deep embedded holes easier than epoxy. The disadvantages are longer set times than epoxy and the bond
stress may also be lower. Williams offers US Spec NA Grout (High Flow, Non-aggregate, Non-shrink grout) for cement
grout bonded anchors. This product is manufactured by US Spec. Has excellent grout bond characteristics and quick
setup times. See page 47 for the NA Grout properties. Shown on the following pages are the various steels and cor-
responding hex nuts that are used for Williams Grout Bonded Concrete Anchors.

Grouted concrete anchors typically use a hex nut at the bottom of the anchor rod. This helps to assure that a failure
will not occur at the grout to bar interface. The modes of failure that can be evaluated for a single grouted concrete
anchor include, ductile steel failure, concrete breakout failure and bond failure. By setting the bar’s ultimate steel
strength equal to the concrete breakout strength, the designer can estimate a recommended embedment depth using
industry design models. In addition bond failure can be checked by using a Uniform Bond Stress Model. Presently the
anchor industry is absent of a formal design code for grouted anchors, however the designer can consider the following
equations for assistance.

Uniform Bond Stress Model

The Uniform Bond Stress Model has been used in some testing to demonstrate the bond behavior of adhesive and
grouted anchor systems by assuming a bond stress that is uniform throughout the anchor systems embedment length.
This model is used to calculate the overall tensile strength of the bond at the grout/concrete interface. The equation
shown below only gives an estimate as bond stress values and concrete compressive strengths do not always give con-
sistent anchor test pull results. Please call your Williams representative for more information on bond stress.

= Bond Strength (lbs)

= Bond Stress for fully cured Grout = 900 psi.**
= 3.14
= Drill Hole Diameter (in.) Note: Minimum 1.5 x bar diameter
= Anchor Embedment Depth (in.)

Concrete Breakout Strength

A designer can estimate the concrete capacity using methods such as ACI 349-97 Appendix B or ACI 318-02
Appendix D. Example:
= Concrete Capacity (lbs)
= Concrete Compressive Strength (psi)
2 2
= ( ) = Projected Cone Area (in )
= Anchor Embedment Depth (in)

Notes:
Williams recommends designing for ductile steel failure whenever possible. Steel strengths can be collected from the strength charts.
** When US Spec NA Grout is used.. Check with your grout manufacturer for ultimate bond strength values when using other grouts.
 Anchor Accessories

H1F Heavy Duty Hex Nuts ASTM 194 Grade Stop-Type & Flange Couplings ASTM A108
Bar Across Across Part Bar Outside Overall Flange Coupling
Thickness
Diameter Flats Corners Number Diameter Diameter Length Flange Size Part Number
1/4" 1/2" .57" 15/64" 1/4" 1/2" 7/8"
H1F-02 - -
(6.4 mm) (12.7 mm) (14.5 mm) (5.95 mm) (6.4 mm) (12.7 mm) (22.2 mm)
3/8" 11/16" .794" 23/64" 3/8" 3/4" 1-1/2" 2” x 2”
H1F-03 C2D-03
(9.5 mm) (17.5 mm) (20.2 mm) (9.1 mm) (9.5 mm) (19.1 mm) (38.1 mm) (51 x 51 mm)
1/2" 7/8" 1.01" 31/64" 1/2" 3/4" 1-1/2" 2” x 2”
H1F-04 C2T-04
(13 mm) (22.2 mm) (25.7 mm) (12.3 mm) (13 mm) (19.1 mm) (38.1 mm) (50.8 x 50.8 mm)
5/8" 1-1/16" 1.23" 39/64" 5/8" 1" 1-3/4" 2” x 2”
H1F-05 C2T-05
(16 mm) (27.0 mm) (31.2 mm) (15.5 mm) (16 mm) (25.4 mm) (44.5 mm) (50.8 x 50.8 mm)
3/4" 1-1/4" 1.44" 47/64" 3/4" 1-1/8" 2" 2” x 2”
H1F-06 C2T-06
(19 mm) (31.8 mm) (36.6 mm) (18.7 mm) (19 mm) (28.6 mm) (50.8 mm) (50.8 x 50.8 mm)
7/8" 1-7/16" 1.66" 55/64" 7/8" 1-1/4" 2-1/4" 3” x 3”
H1F-07 C2T-07
(22 mm) (36.6 mm) (42.2 mm) (21.8 mm) (22 mm) (31.8 mm) (57.2 mm) (76.2 x 76.2 mm)
1" 1-5/8" 1.88" 63/64" 1" 1-1/2" 3" 3” x 3”
H1F-08 C2T-08
(25 mm) (41.3 mm) (47.8 mm) (25.0 mm) (25 mm) (38.1 mm) (76.2 mm) (76.2 x 76.2 mm)
1-1/8" 1-13/16" 2.09" 1-7/64" H1F-09 1-1/8" 1-5/8" 3-1/2" 3” x 3”
(29 mm) (46.0 mm) (53.1 mm) (28.2 mm) C2T-09
(29 mm) (41.3 mm) (88.9 mm) (76.2 x 76.2 mm)
1-1/4" 2" 2.31" 1-7/32" 1-1/4" 1-7/8" 3-3/4" 3” x 3”
H1F-10 C2T-10
(32 mm) (50.8 mm) (58.7 mm) (31.0 mm) (32 mm) (47.6 mm) (95.3 mm) (76.2 x 76.2 mm)
1-3/8" 2-3/16" 2.53" 1-11/32" 1-3/8" 2-1/8" 4" 3” x 3”
H1F-11 C2T-11
(36 mm) (55.6 mm) (64.3 mm) (34.1 mm) (36 mm) (54.0 mm) (102 mm) (76.2 x 76.2 mm)
1-1/2" 2-3/8" 2.74" 1-15/32" 1-1/2" 2-1/4" 5" 3” x 3”
H1F-12 C2T-12
(38 mm) (60.3 mm) (69.6 mm) (37.3 mm) (38 mm) (57.2 mm) (127 mm) (76.2 x 76.2 mm)
1-3/4" 2-3/4" 3.18" 1-23/32" 1-3/4" 2-1/2" 5-1/2" 4” x 4”
H1F-14 C2T-14
(43 mm) (69.9 mm) (80.8 mm) (43.7 mm) (43 mm) (63.5 mm) (140 mm) (102 x 102 mm)
1-7/8" 2-15/16" 3.39" 1-27/32" 1-7/8" 2-7/8" 6"
H1F-15 - -
(48 mm) (74.6 mm) (86.1 mm) (46.8 mm) (48 mm) (73 mm) (152 mm)
2" 3-1/8" 3.61" 1-31/32" 2" 3" 6"
H1F-16 - -
(51 mm) (79.4 mm) (91.7 mm) (50.0 mm) (51 mm) (76 mm) (152 mm)

R9F Hardened Washers - ASTM F436 R8M Beveled Washers - ASTM A47 or ASTM A536
Bar Outside Inside Part Bar Degree Outside Inside Maximum Minimum Part
Thickness
Diameter Diameter Diameter Number Diameter of Bevel Diameter Diameter Thickness Thickness Number
1/4" 5/8" 9/32" 1/16" 1/4"
R9F-02-436 - - - - - -
(6.4 mm) (15.9 mm) (7.1 mm) (1.58 mm) (6.4 mm)
3/8" 1" 7/16" 5/64" 3/8" 1-1/4" 9/16" 7/16" 1/8"
R9F-03-436 14°
(9.5 mm) (25.4 mm) (11.1 mm) (1.98 mm) (9.5 mm) (31.8 mm) (14.3 mm) (11.1 mm) (3.18 mm) R8M-03
1/2" 1-3/8" 9/16" 9/64" 1/2" 1-1/4" 9/16" 7/16" 1/8"
R9F-04-436 14°
(13 mm) (34.9 mm) (14 mm) (3.57 mm) (13 mm) (31.8 mm) (14.3 mm) (11.1 mm) (3.18 mm) R8M-04
5/8" 1-3/4" 11/16" 9/64" 5/8" 1-9/16" 13/16" 1/2" 3/16"
R9F-05-436 11°
(16 mm) (44.5 mm) (17 mm) (3.57 mm) (16 mm) (39.7 mm) (20.6 mm) (12.7 mm) (4.76 mm) R8M-06
3/4" 1-15/32" 13/16" 9/64" 3/4" 1-9/16" 13/16" 1/2" 3/16”
R9F-06-436 11°
(19 mm) (37.3 mm) (21 mm) (3.57 mm) (19 mm) (39.7 mm) (20.6 mm) (12.7 mm) (4.76 mm) R8M-06
7/8" 1-3/4" 15/16" 5/32" 7/8" 2" 1-3/16" 9/16" 1/4"
R9F-07-436 9°
(22 mm) (44.5 mm) (23.8 mm) (3.97 mm) (22 mm) (50.8 mm) (30.2 mm) (14.3 mm) (6.35 mm) R8M-09
1" 2" 1-1/8" 5/32" 1" 2" 1-3/16" 9/16" 1/4"
R9F-08-436 9°
(25 mm) (50.8 mm) (28.6 mm) (3.97 mm) (25 mm) (50.8 mm) (30.2 mm) (14.3 mm) (6.35 mm) R8M-09
1-1/8" 2-1/4" 1-1/4" 5/32" 1-1/8" 2-13/16" 1-5/16" 1" 5/16"
R9F-09-436 15°
(29 mm) (57.2 mm) (31.8 mm) (3.97 mm) (29 mm) (71.4 mm) (33.3 mm) (25.4 mm) (7.94 mm) R8M-09S
1-1/4" 2-1/2" 1-3/8" 5/32" 1-1/4" 3-3/8" 1-9/16" 1-15/64" 3/8"
R9F-10-436 15°
(32 mm) (63.5 mm) (34.9 mm) (3.97 mm) (32 mm) (85.7 mm) (39.7 mm) (31.4 mm) (9.53 mm) R8M-12S
1-3/8" 2-3/4" 1-1/2" 5/32" 1-3/8" 3-3/8" 1-9/16" 1-15/64" 3/8"
R9F-11-436 15°
(36 mm) (69.9mm) (38.1 mm) (3.97 mm) (36 mm) (85.7 mm) (39.7 mm) (31.4 mm) (9.53 mm) R8M-12S
1-1/2" 3" 1-5/8" 5/32" 1-1/2" 3-1/2" 1-3/4" 1-1/4" 3/8"
R9F-12-436 15°
(38 mm) (76.2 mm) (41.3 mm) (3.97 mm) (38 mm) (88.9 mm) (44.5 mm) (31.8 mm) (9.53 mm) R8M-13S
1-3/4" 3-3/8" 1-7/8" 7/32" 1-3/4" 3-9/16" 2-1/16" 13/16" 1/2"
R9F-14-436 5°
(43 mm) (85.7 mm) (47.6 mm) (5.56 mm) (43 mm) (90.5 mm) (52.4 mm) (20.6 mm) (12.7 mm) R8M-16
1-7/8" 3-3/4" 2-1/8" 7/32" 1-7/8" 3-9/16" 2-1/16" 13/16" 1/2"
R9F-16-436 5°
(48 mm) (95.3 mm) (54.0 mm) (5.56 mm) (48 mm) (90.5 mm) (52.4 mm) (20.6 mm) (12.7 mm) R8M-16
2" 3-3/4" 2-1/8" 7/32" 2" 3-9/16" 2-1/16" 13/16" 1/2"
R9F-16-436 5°
(51 mm) (95.3 mm) (54.0 mm) (5.56 mm) (51 mm) (90.5 mm) (52.4 mm) (20.6 mm) (12.7 mm) R8M-16
 150 KSI All-Thread-Bar

R71 150 KSI All-Thread-Bar - ASTM A722*

Nominal Bar Minimum Minimum M
ACI 355.1R section [Link] indicates an ulti-
Prestressing Force Nominal Approx. Part mate strength in shear has a range of .6 to .7
Diameter Net Area Ultimate Thread Number
Weight of the ultimate tensile strength. Designers
& Pitch Thru Threads Strength 0.80f pu A 0.70f pu A 0.60f pu A Major Dia.
should provide adequate safety factors for safe
1" - 4 0.85 in2 128 kips 102 kips 89.3 kips 76.5 kips 3.09 lbs./ft. 1-1/8" shear strengths based on the condition of use.
(26 mm) (549 mm2) (567 kN) (454 kN) (397 kN) (340 kN) (4.6 Kg/M) (28.6 mm) R71-08
1-1/4" - 4 1.25 in2 188 kips 150 kips 131 kips 113 kips 4.51 lbs./ft. 1-7/16" M Per PTI recommendations for anchoring,
(32 mm) (807 mm2) (834 kN) (667 kN) (584 kN) (500 kN) (6.71 Kg/M) (36.5 mm) R71-10 anchors should be designed so that:
M The design load is not more than 60% of
1-3/8" - 4 1.58 in2 237 kips 190 kips 166 kips 142 kips 5.71 lbs./ft. 1-9/16" the specified minimum tensile strength of
(36 mm) (1019 mm2) (1054 kN) (843 kN) (738 kN) (633 kN) (8.50 Kg/M) (39.7 mm) R71-11 the prestressing steel.
M The lock-off load should not exceed 70%
1-3/4" - 3-1/2 2.60 in2 390 kips 312 kips 273 kips 234 kips 9.06 lbs./ft. 2"
(46 mm) (1664 mm2) (1734 kN) (1388 kN) (1214 kN) (1041 kN) (13.5 Kg/M) (50.8 mm) R71-14 of the specified minimum tensile strength
of the prestressing steel.
2-1/4" - 3-1/2 4.08 in2 613 kips 490 kips 429 kips 368 kips 14.1 lbs./ft. 2-1/2" M The maximum test load should not exceed
(57 mm) * (2632 mm2) (2727 kN) (2181 kN) (1909 kN) (1636 kN) (20.8 Kg/M) (63.5 mm) R71-18 80% of the specified minimum tensile
strength of the prestressing steel.
2-1/2" - 3 5.19 in2 778 kips 622 kips 545 kips 467 kips 18.2 lbs./ft. 2-3/4"
(65 mm) (3350 mm2) (3457 kN) (2766 kN) (2422 kN) (2074 kN) (27.1 Kg/M) (69.9 mm) R71-20
3" - 3 6.46 in2 969 kips 775 kips 678 kips 581 kips 22.3 lbs./ft. 3-3/64"
(75 mm) * (4169 mm2) (4311 kN) (3448 kN) (3018 kN) (2587 kN) (32.7 Kg/M) (77.4 mm) R71-24
* The 2-1/4” and 3" diameter bars are not covered under ASTM A722.

Sizes Steel Quality

Williams 150 KSI bars are manufactured in 7 diame- Williams 1”, 1-1/4”, & 1-3/8” 150 KSI bars are smooth,
ters from 1” (26 mm) through 3” (75 mm). Most diameters hot rolled, high strength prestressing steel. The bars are
are available in continuous lengths up to 50’ (15.2 m). cold-stressed and stress relieved to produce the above
properties. The 1-3/4” through 3” 150 KSI bars are from an
alloy based steel that is hot rolled, quenched and tempered
Threads to produce to the prescribed mechanical properties of
All-Thread-Bars are cold rolled threaded to close tol- ASTM A722-07.
erances under continuous monitoring procedures for Thorough inspection and traceability are carried out
quality control. Threads for Williams 150 KSI bar are during all phases of manufacturing to assure the highest
specially designed with a rugged thread pitch wide standards of quality.
enough to be fast under job site conditions and easy to
assemble. They also have a smooth, wide, concentric, Properties
surface suitable for torque tensioning. This combination Williams 150 KSI bars are manufactured in strict com-
offers tremendous installation savings over inefficient,
pliance with ASTM A722-07 and AASHTO M275
hot rolled, non-concentric thread forms. Threads are
available in both right and left hand. Highway Specifications. The prestressing steel is high in
Williams All-Thread-Bars are threaded around the full strength yet ductile enough to exceed the specified elon-
circumference enabling the load transfer from the bar to gation and reduction of area requirements. Selected
the fasteners to occur efficiently without eccentric point heats can also pass the 135° supplemental bend test
loading. Williams fasteners easily meet the allowable when required. Testing has shown Williams 150 KSI All-
load transfer limitations set forth by the Post Tensioning Thread-Bars to meet or exceed post tensioning bar and
Institute. Williams 150 KSI All-Thread-Bars and fasten- rock anchoring criteria as set by the Post Tensioning
ers are machined to tight tolerances for superior per- Institute including dynamic test requirements beyond
formance and mechanical lock. Precision machining 500,000 cycles of loading.
greatly reduces concern of fastener loosening or deten- Williams 360° continuous thread deformation pattern
sioning. Williams 150 KSI bars exceed the deformation
has the ideal relative rib area configuration to provide
requirements of ASTM A722-07. Williams special thread
deformation pattern projects ultra high relative rib area, excellent bond strength capability to grout or concrete, far
much greater than conventional rebar. This provides for better than traditional reinforcing deformation patterns.
superior bond performance in concrete.
Tensile Strength & Working Loads
Williams 150 KSI bars are available with ultimate ten-
Cutting (No Welding) sile strengths and working loads as displayed above.
Williams 150 KSI All-Thread-Bar should not be sub- Safety factors and functional working loads are at the
jected to the heat of a torch, welding or used as a discretion of the project design engineer, however test
ground. Field cutting should be done with an abrasive loads should never exceed 80% of the published ultimate
wheel or band saw. bar strength.
 150 KSI All-Thread-Bar Accessories
Rounded
Collar
Nut
Hex
Nut

R73 Hex Nuts - ASTM A29 R72 Stop-Type Coupling - ASTM A29, Grade C1045
Bar Across Across Thickness Part Bar Outside Overall Part
Diameter Flats Corners Number Diameter Diameter Length Number
1" 1-3/4" 2.02" 2" R73-08 1" 1-3/4" 4-1/4" R72-08
(26 mm) (44.5 mm) (51.3 mm) (50.8 mm) (26 mm) (44.5 mm) (108 mm)
1-1/4" 2-1/4" 2.60" 2-1/2" R73-10 1-1/4" 2-1/8" 5-1/4" R72-10
(32 mm) (57.2 mm) (66.0 mm) (63.5 mm) (32 mm) (54.0 mm) (133 mm)
1-3/8" 2-1/2" 2.89" 2-3/4" R73-11 1-3/8" 2-3/8" 5-3/4" R72-11
(36 mm) (63.5 mm) (73.4 mm) (69.9 mm) (36 mm) (60.3 mm) (146 mm)
1-3/4" 3" 3.46" 3-1/2" R73-14 1-3/4" 3" 8-1/2" R72-14
(46 mm) (76.2 mm) (87.9 mm) (88.9 mm) (46 mm) (76.2 mm) (216 mm)
2-1/4" 3-1/2" 4" 4-1/4" R73-18 2-1/4" 3-1/2" 9” R72-18
(57 mm) (88.9 mm) (102 mm) (108 mm) (57 mm) (88.9 mm) (229 mm)
2-1/2" 4-1/4" 4.90" 4-3/4" R73-20 2-1/2" 4-1/4” 9-3/8” R72-20
(65 mm) (108 mm) (124 mm) (121 mm) (65 mm) (108 mm) (238 mm)
3" * 4-1/4" 5" 6-1/8" R74-24 3" 5" 11-7/8" R72-24
(75 mm) (108 mm) (127 mm) (156 mm) (75 mm) (127 mm) (302 mm)
* Rounded collar nut with OD of 5” (127 mm).

)C@G:56D
FA
E@
R
2?8=6
when used with a dished plate.

R9F Hardened Washers - ASTM F436 R88 Spherical Hex Nuts - ASTM A536
Bar Outside Inside Thickness Part Bar Across Thickness Outside Part
Diameter Diameter Diameter Number Diameter Flats Dome Number
1" 2-1/4" 1-1/4" 5/32" 1" 1-3/4" 2-1/4" 2-1/2"
(26 mm) (57.2 mm) (31.8 mm) R9F-09-436 (26 mm) (44.5 mm) (57.2 mm) (63.5 mm) R88-08
(3.97 mm)
1-1/4" 2-3/4” 1-1/2" 5/32" 1-1/4" 2-1/4" 2-3/4" 3-1/8"
(32 mm) (69.9 mm) (38.1 mm) R9F-11-436 (32 mm) (57.2 mm) (69.9 mm) (79.5 mm) R88-10
(3.97 mm)
1-3/8" 3" 1-5/8" 5/32" 1-3/8" 2-1/2" 3-1/4" 3-5/8"
(36 mm) (76.2 mm) (41.3 mm) R9F-12-436 (36 mm) (63.5 mm) (82.6 mm) (90.2 mm) R88-11
(3.97 mm)
1-3/4" 3-3/4" 2-1/8" 7/32" 1-3/4" 3" 3-1/2" 4"
(46 mm) R9F-16-436 (46 mm) (76.2 mm) (88.9 mm) (102 mm) R88-14
(95.3 mm) (54.0 mm) (5.56 mm)
2-1/4" 4-1/2” 2-5/8” 9/32" 2-1/4” * 3-1/2" 5-3/4” 5-1/2” R73-18
(57 mm) (114 mm) (66.7 mm) R9F-20-436 (57 mm) (88.9 mm) (146 mm) (140 mm) R81-18
(7.14 mm)
2-1/2" 5" 2-7/8" 9/32" 2-1/2" * 4-1/4" 6-1/2" 6" R73-20
(65 mm) (127 mm) (73.0 mm) R9F-22-436 (65 mm) (108 mm) (165 mm) (152 mm) R81-20
(7.14 mm)
3" 6" 3-3/8" 9/32" 3" ** 4-1/4" 8-1/8" 7" R74-24
(75 mm) (152 mm) (85.7 mm) R9F-26-436 (75 mm) (108 mm) (206 mm) (178 mm) R81-24
(7.14 mm)
* Requires a standard nut with spherical washer assembly.
** Requires rounded collar nut with spherical washer assembly.

These Jam Nuts can't be substi-

tute for full strength nuts and
can't be used on bars other than
Williams 150 KSI All-Thread-
Bars of the same diameter.

R73-JN Jam Nuts - ASTM A29, R8M Beveled Washers - ASTM A47 or ASTM A536
Bar Across Thickness Part Bar Degree Outside Inside Maximum Minimum Part
Diameter Flats Number Diameter of Bevel Diameter Diameter Thickness Thickness Number
1" 1-3/4" 1/2" R73-08JN 1" 10° 2-27/32” 1-7/16" 7/8" 3/8"
(26 mm) (44.5 mm) (12.7 mm) (26 mm) (72.2 mm) (36.5 mm) (22.2 mm) (9.52 mm) R8M-08-150
1-1/4" 2-1/4" 5/8" R73-10JN 1-1/4" * 15° 5-1/4" 1-21/32" 1-41/64" 19/64"
(32 mm) (57.2 mm) (15.9 mm) (32 mm) (133 mm) (42.1 mm) (41.7 mm) (7.54 mm) R8M-10-150
1-3/8" 2-1/2" 11/16" R73-11JN 1-3/8" * 15° 5-1/4" 1-25/32" 1-41/64" 19/64"
(36 mm) (63.5 mm) (17.5 mm) (36 mm) (133 mm) (45.2 mm) (41.7 mm) (7.54 mm) R8M-11-150
1-3/4" 3" 7/8" R73-14JN 1-3/4" 10° 5-1/2" 2-1/2" 1-23/32" 3/4"
(46 mm) (76.2 mm) (22.2 mm) (46 mm) (140 mm) (63.5 mm) (43.7 mm) (19.0 mm) R8M-14-150
2-1/4" * 3-1/4” 1” R73-18JN 2-1/4" 10° 6-1/2” 3” 1-7/8” 3/4"
(57 mm) (82.6 mm) (25.4 mm) (57 mm) (165 mm) (76.2 mm) (47.6 mm) (19.0 mm) R8M-18-150
2-1/2" 4" 1-3/16" R73-20JN 2-1/2" 10° 7-1/2" 3-1/2" 2.31" 1"
(65 mm) (102 mm) (30.2 mm) (65 mm) (190 mm) (88.9 mm) (58.7 mm) (25.4 mm) R8M-20-150
3" * 4-1/2" 2" R74-24JN 3"* 10° 8" 3-5/8" 2.43" 1"
(75 mm) (114 mm) (50.8 mm) (75 mm) (203 mm) (92.1 mm) (61.7 mm) (25.4 mm) R8M-24-150
* Rounded collar nut * Additional USS Hardened Washer Required
 Grade 75 All-Thread Rebar

Threads R61 Grade 75 All-Thread Rebar - ASTM A615*

Williams Grade 75 All-Thread Rebar has a
Bar Designation Minimum Minimum Minimum Nominal Approx.
cold rolled, continuous, rounded course thread Nominal Diameter Net Area Ultimate Yield Thread Part
form. Because of the full 360º concentric thread & Pitch Thru Threads Strength Strength Weight Major Dia. Number
form, Williams All-Thread Rebar should only be #6 - 3/4" - 5 0.44 in2 44 kips 33 kips 1.5 lbs./ft. 7/8"
bent under special provisions. Williams special (19 mm) (284 mm2) (196 kN) (147 kN) (2.36 Kg/M) (22.2 mm) R61-06
thread (deformation) pattern projects ultra high rel- #7 - 7/8" - 5 0.60 in2 60 kips 45 kips 2.0 lbs./ft. 1"
(22 mm) (387 mm2) (267 kN) (200 kN) (3.04 Kg/M) (25.4 mm) R61-07
ative rib area at 3 times that of conventional rebar. #8 - 1" - 3-1/2 0.79 in2 79 kips 59.3 kips 2.7 lbs./ft. 1-1/8"
This provides for superior bond performance in (25 mm) (510 mm2) (351 kN) (264 kN) (3.94 Kg/M) (28.6 mm) R61-08
concrete. Threads are available in both right and #9 - 1-1/8" - 3-1/2 1.00 in2 100 kips 75 kips 3.4 lbs./ft. 1-1/4"
left hand. Grade 80 is available upon request. (29 mm) (645 mm2) (445 kN) (334 kN) (5.06 Kg/M) (31.8 mm) R61-09
#10 - 1-1/4" - 3 1.27 in2 127 kips 95.3 kips 4.3 lbs./ft. 1-3/8"
(32 mm) (819 mm2) (565 kN) (424 kN) (5.50 Kg/M) (34.9 mm) R61-10
Sizes
#11 - 1-3/8" - 3 1.56 in2 156 kips 117 kips 5.3 lbs./ft. 1-1/2"
All-Thread Rebar is available in 11 diameters (36 mm) (1006 mm2) (694 kN) (521 kN) (7.85 Kg/M) (38.1 mm)
R61-11
from #6 (20 mm) through #28 (89 mm). Most #14 - 1-3/4" - 3 2.25 in 2
225 kips 169 kips 7.65 lbs./ft. 1-7/8"
diameters are available in continuous lengths up (43 mm) (1452 mm2) (1001 kN) (750 kN) (11.8 Kg/M) (47.6 mm) R61-14
to 50’ (15.2 m). #18 - 2-1/4" - 2-3/4 4.00 in2 400 kips 300 kips 13.6 lbs./ft. 2-7/16"
(57 mm) (2581 mm2) (1780 kN) (1335 kN) (19.6 Kg/M) (61.9 mm) R61-18
Welding #20 - 2-1/2" - 2-3/4 4.91 in2 491 kips 368 kips 16.7 lbs./ft. 2-3/4"
(64 mm) (3168 mm2) (2184 kN) (1637 kN) (24.8 Kg/M) (69.9 mm) R61-20
Welding of All-Thread Rebar should be
#24 - 3” - 2-3/4 6.82 in2 682 kips 512 kips 24.0 lbs./ft. 3-3/16”
approached with caution since no specific provi- (76 mm) * (4400 mm2) (3034 kN) (2277 kN) (35.8 Kg/M) (81.0 mm) R61-24
sions have been included to enhance its weld- #28 - 3-1/2" - 2-3/4 9.61 in2 961 kips 720 kips 32.7 lbs./ft. 3-3/4"
ability. Refer to ANSI/AWS D1.4 for proper selec- (89 mm) * (6200 mm2) (4274 kN) (3206 kN) (48.6 Kg/M) (95.3 mm) R61-28
tions and procedures. * The #24 and #28 diameter bars are not covered under ASTM A615.

Round Collar
Hex
All Couplings and Hex Nuts Nut
Nut
exceed 100% of the bar’s pub-
lished ultimate strength and meet
ACI 318 Section [Link] for
mechanical rebar connections.

R62 Stop-Type Coupling - ASTM A108 R63 Hex Nut - ASTM A108
Bar Desig. & Outside Overall Part Bar Desig. & Across Across Part
Thickness
Nominal Dia. Diameter Length Number Nominal Dia. Flats Corners Number
#6 - 3/4" 1-1/4" 3-1/2" #6 - 3/4" 1-1/4" 1.44" 1-5/8"
R62-06 R63-06
(19 mm) (31.8 mm) (88.9 mm) (19 mm) (31.8 mm) (36.6 mm) (41.3 mm)
#7 - 7/8" 1-3/8" 4" #7 - 7/8" 1-7/16" 1.66" 1-3/4"
R62-07 R63-07
(22 mm) (34.9 mm) (102 mm) (22 mm) (36.5 mm) (42.2 mm) (44.5 mm)
#8 - 1" 1-5/8" 4-1/2" #8 - 1" 1-5/8" 1.88" 2"
R62-08 R63-08
(25 mm) (41.3 mm) (114 mm) (25 mm) (41.3 mm) (47.8 mm) (50.8 mm)
#9 - 1-1/8" 1-7/8" 5" #9 - 1-1/8" 1-7/8" 2.16" 2"
R62-09 R63-09
(29 mm) (47.7 mm) (127 mm) (29 mm) (47.6 mm) (54.9 mm) (50.8 mm)
#10 - 1-1/4" 2" 5-1/2" #10 - 1-1/4" 2" 2.31" 2-3/16"
R62-10 R63-10
(32 mm) (50.8 mm) (140 mm) (32 mm) (50.8 mm) (58.7 mm) (55.6 mm)
#11 - 1-3/8" 2-1/4" 6" #11 - 1-3/8" 2-1/4" 2.60" 2-13/32"
R62-11 R63-11
(36 mm) (57.2 mm) (152 mm) (36 mm) (57.2 mm) (66.0 mm) (61.1 mm)
#14 - 1-3/4" 2-7/8" 7-7/8" #14 - 1-3/4" 2-3/4" 3.18" 3-1/4"
R62-14 R63-14
(43 mm) (73.0 mm) (200 mm) (43 mm) (69.9 mm) (80.8 mm) (82.6 mm)
#18 - 2-1/4” 3-1/2" 9-1/8" #18 - 2-1/4” 3-1/2" 4.04" 3-1/2"
R62-18 R63-18
(57 mm) (88.9 mm) (232 mm) (57 mm) (88.9 mm) (103 mm) (88.9 mm)
#20 - 2-1/2" 4" 9-1/2" #20 - 2-1/2" 4" 4.62" 4"
R62-20 R63-20
(64 mm) (102 mm) (241 mm) (64 mm) (102 mm) (117 mm) (102 mm)
#24 - 3” 5” 11-1/4” * #24 - 3” 4-1/2” O.D. 5" 5”
R62-24 R64-24*
(76 mm) (127 mm) (286 mm) (76 mm) (114 mm) (127 mm) (127 mm)
#28 - 3-1/2” 5-1/2" 12" * #28 - 3-1/2” 5-1/2" O.D. 6" 6"
R62-28 R64-28*
(89 mm) (140 mm) (305 mm) (89 mm) (140 mm) (152 mm) (142 mm)
 Grade 75 All-Thread Rebar Accessories

R81 Spherical Washers - ASTM A536 R9F Hardened Washers - ASTM F436
Bar Desig. & Outside Part Bar Desig. & Outside Inside Part
Thickness Thickness
Nominal Dia. Dome Number Nominal Dia. Diameter Diameter Number
#6 - 3/4" 35/64” 2" #6 - 3/4" 1-3/4" 15/16" 5/32"
R81-0675 R9F-07-436
(19 mm) (13.9 mm) (50.8 mm) (19 mm) (44.5 mm) (23.8 mm) (3.97 mm)
#7 - 7/8" 39/64” 2-1/4" #7 - 7/8" 2" 1-1/8" 5/32"
R81-0775 R9F-08-436
(22 mm) (15.5 mm) (57.2 mm) (22 mm) (50.8 mm) (28.6 mm) (3.97 mm)
#8 - 1" 5/8” 2-1/2" #8 - 1" 2-1/4" 1-1/4" 5/32"
R81-0875 R9F-09-436
(25 mm) (15.9 mm) (63.5 mm) (25 mm) (57.2 mm) (31.8 mm) (3.97 mm)
#9 - 1-1/8" 3/4” 2-3/4" #9 - 1-1/8" 2-1/4" 1-1/4" 5/32"
R81-0975 R9F-09-436
(29 mm) (19.1 mm) (69.9 mm) (29 mm) (57.2 mm) (31.8 mm) (3.97 mm)
#10 - 1-1/4" 53/64” 3" #10 - 1-1/4" 2-1/2" 1-3/8" 5/32"
R81-1075 R9F-10-436
(32 mm) (21.0 mm) (76.2 mm) (32 mm) (63.5 mm) (34.9 mm) (3.97 mm)
#11 - 1-3/8" 29/32” 3-1/4" #11 - 1-3/8" 3" 1-5/8" 5/32"
R81-1175 (3.97 mm) R9F-12-436
(36 mm) (23.0 mm) (82.5 mm) (36 mm) (76.2 mm) (41.3 mm)
#14 - 1-3/4" 1-7/64” 3-3/4" #14 - 1-3/4" 3-3/8" 1-7/8" 7/32"
R81-1475 R9F-14-436
(43 mm) (28.2 mm) (95.3 mm) (43 mm) (85.7 mm) (47.6 mm) (5.56 mm)
#18 - 2-1/4” 1-13/32” 5" #18 - 2-1/4” 4-1/2" 2-5/8" 9/32"
R81-1875 R9F-20-436
(57 mm) (35.7 mm) (127 mm) (57 mm) (114 mm) (66.7 mm) (7.14 mm)
#20 - 2-1/2" 1-1/2” 5-1/4" #20 - 2-1/2" 5" 2-7/8" 9/32"
R81-2075 R9F-22-436
(64 mm) (38.1 mm) (133 mm) (64 mm) (127 mm) (73.0 mm) (7.14 mm)
#24 - 3” 1-7/8” 6-1/2” #24 - 3” 6" 3-3/8” 9/32"
R81-2475 R9F-26-436
(76 mm) (47.6 mm) (165 mm) (76 mm) (142 mm) (85.7 mm) (7.14 mm)
#28 - 3-1/2” 1-1/2” 7" #28 - 3-1/2” 7" 3-7/8" 9/32"
R81-2875 R9F-30-436
(89 mm) (38.1 mm) (178 mm) (89 mm) (178 mm) (98.4 mm) (7.14 mm)
)C@G:56D
FA
E@
R
2?8=6
H96?
FD65
H:E9
2
5:D965
A=2E6

These Jam Nuts can not

be substitute for full
strength nuts and can not
be used on bars other
than Williams Grade 75
All-Thread Rebar of the
same diameter.

R63-JN Jam Nuts - ASTM A108 R8M Beveled Washers - ASTM A47 or ASTM A536
Bar Desig. & Across Part Bar Desig. & Degree Outside Inside Maximum Minimum Part
Thickness
Nominal Dia. Flats Number Nominal Dia. of Bevel Diameter Diameter Thickness Thickness Number
#6 - 3/4" 1-1/4" 13/16" #6 - 3/4" 2" sq. 1" 17/32" 15/64"
R63-06JN 9°
(19 mm) (31.8 mm) (20.6 mm) (19 mm) (50.8 mm) (25.4 mm) (13.5 mm) (5.95 mm) R8M-07
#7 - 7/8" 1-7/16" 7/8" #7 - 7/8" 2" 1-3/16" 9/16" 1/4"
R63-07JN 9°
(22 mm) (36.5 mm) (22.2 mm) (22 mm) (50.8 mm) (30.2 mm) (14.3 mm) (6.35 mm) R8M-09
#8 - 1" 1-5/8" 1" #8 - 1" 2-13/16" 1-5/16" 1" 5/16"
R63-08JN 15°
(25 mm) (41.3 mm) (25.4 mm) (25 mm) (71.4 mm) (33.3 mm) (25.4 mm) (7.94 mm) R8M-09S
#9 - 1-1/8" 1-7/8" 1" #9 - 1-1/8" 2-13/16" 1-5/16" 1" 5/16"
R63-09JN 15°
(29 mm) (47.6 mm) (25.4 mm) (29 mm) (71.4 mm) (33.3 mm) (25.4 mm) (7.94 mm) R8M-09S
#10 - 1-1/4" 2" 1-3/32" #10 - 1-1/4" 3-3/8" 1-9/16" 1-15/64" 3/8"
R63-10JN 15°
(32 mm) (50.8 mm) (27.8 mm) (32 mm) (85.7 mm) (39.7 mm) (43.9 mm) (9.53 mm) R8M-12S
#11 - 1-3/8" 2-1/4" 1-1/4" #11 - 1-3/8" 3-1/2" 1-3/4" 1-1/4" 3/8"
R63-11JN 15°
(36 mm) (57.2 mm) (31.8 mm) (36 mm) (88.9 mm) (44.5 mm) (31.8 mm) (9.53 mm) R8M-13S
#14 - 1-3/4" 2-3/4" 1-5/8" #14 - 1-3/4" 3-9/16" 2-1/16" 13/16" 1/2"
R63-14JN 5°
(43 mm) (69.9 mm) (41.3 mm) (43 mm) (90.5 mm) (52.4 mm) (20.6 mm) (12.7 mm) R8M-16
#18 - 2-1/4” 3-1/2" 1-3/4" #18 - 2-1/4” 5" 3" 1-5/8" 19/64"
R63-18JN 15°
(57 mm) (88.9 mm) (44.5 mm) (57 mm) (127 mm) (76.2 mm) (41.3 mm) (7.54 mm) R8M-18
#20 - 2-1/2" 4" 2" #20 - 2-1/2" 5-1/2" 3" 1-23/32" 3/4”
R63-20JN 10° R8M-20
(64 mm) (102 mm) (50.8 mm) (64 mm) (140 mm) (76.2 mm) (43.7 mm) (19 mm)
* #24 - 3” 4-1/2” 2-1/4” #24 - 3” 7” 3-5/8” 2” 3/4”
R64-24JN* 10°
(76 mm) (114 mm) (57.2 mm) (76 mm) (178 mm) (92 mm) (50.8 mm) (19.1 mm) R8M-24
* #28 - 3-1/2” 5" 2-1/2" #28 - 3-1/2” 8" 4-1/4" 2-19/64" 7/8"
R64-28JN* 10°
(89 mm) (127 mm) (63.5 mm) (89 mm) (203 mm) (108 mm) (58.3 mm) (22.2 mm) R8M-28
 Anchor Accessories
Bearing Plates
Williams steel bearing plates are standard with a
round hole for non-grouted concrete anchors. Also avail- S1K - Round R80 - Dished S1K - Keyhole
able are dished plates for use with spherical hex nuts
and keyhole plates which provide free access for grout
tube entry. Bearing plates are customized for each appli-
cation. Plate dimensions should be specified around the
parameters of the project. In addition, corrosion protec-
tion should be considered along with specifying hole
diameter and bar angle. Stainless steel plates available
upon request.

End Caps
Williams offers end caps produced from fiber reinforced nylon, steel or PVC to provide corrosion protection at otherwise
exposed anchor ends. Most often the caps are packed with corrosion inhibiting wax or grease. Caps made from reinforced
nylon and steel are used in exposed impact areas. The fiber reinforced nylon end cap meets the Florida DOT standards.

Fiber Steel Tube welded on

Reinforced Flange with Threaded Steel Tube with Screw-On PVC Cap Slip-On
Nylon Cap Screw Connections Jam Nut with Plastic Nut PVC Cap

Eye Nuts NEB 1 E1N CCF 2 thru 4

Williams Eye Nuts may be used as lifting eyes for
forms, concrete blocks, concrete cylinders, machinery or
equipment. The large base on three of the models
makes them excellent for anchoring guy wires. Safety
factors and working loads based on the ultimate strength
of the Eye Nuts should be determined for the specific
application by the project design engineer.

Taps Straight Straight

Eye Nut Inside Inside Ring Overall Available Tension Blank Part
Tension
Designation Width Height Diameter Height Ultimate Number
UNC / Coil Grade 75 150 KSI B7X SWL
Strength
NEB 1 2" 2" 1-1/8" 5-1/8" 3/4" - 1" 35 kips 8.7 kips
#6 - -
Ductile Iron (51 mm) (51 mm) (29 mm) (130 mm) (20 - 25 mm) (156 kN) (38.9 kN) E1M-00-001
E1N 2" 2-1/2" 7/8" 5-1/8" 3/4" - 1" 70 kips 17.5 kips
#6 - #8 - -
Cast Steel (51 mm) (64 mm) (22 mm) (130 mm) (20 - 25 mm) (312 kN) (77.8 kN) E1M-00-E1N
CCF 2 2" 2-1/2" 5/8" 4-3/8" 3/4" - 1" 55 kips 11 kips
#6 - -
Forged Steel (51 mm) (64 mm) (16 mm) (111 mm) (20 - 25 mm) (224 kN) (49 kN) E1M-00-CCF2
CCF 3 2-1/2" 2-5/8" 7/8" 5-5/8" 1-1/8" - 1-1/4" 110 kips 22 kips
#9 - 32 mm
Forged Steel (64 mm) (66 mm) (22 mm) (143 mm) (29 - 32 mm) (489 kN) (98 kN) E1M-00-CCF3
CCF 4 4" 6-1/4" 1-1/4" 10" 1-3/8" - 2" 260 kips 52 kips
#10-#14 1” - 1-3/8” 38 - 51 mm (1157
Forged Steel (101 mm) (158 mm) (32 mm) (254 mm) (35 - 51 mm) kN) (231 kN) E1M-00-CCF4
 Grouting Accessories
S5Z WIL-X CEMENT GROUT Compressive Strength
Wil-X Cement Grout & Water
Conforms to ASTM C845-76 T (74° F Dry Environment)
Wil-X is chemically compensated for shrinkage. It has a 0.44 w/c ratio
high bond value and is crack resistant for permanent instal- Time PSI MPa
lations. Because it is a cement-grout, it is non-explosive and 1 Day 3,200 22.2
3 Days 4,800 33.1
has a long shelf life when kept dry.
7 Days 6,700 46.2
28 Days 10,200 70.3

Wil-X may be used to build up leveling pads by simply mixing

with sand or pea gravel. This mixture should not be run through
the grout pump.
Setting Time: Gilmore Needles (ASTM C266). Initial set 45
minutes; final set 10 hours.
Comparative compressive strength test in PSI (modified
5 gallon, resealable,
94 lbs. bag
ASTM C109) Actual strengths as mixed according to Williams
moisture proof,
Instructions range from 6,000 to 10,200 PSI depending on water polypropylene pails
content. Copy of ASTM Modification available upon request.

US Spec NA Grout
Product Description
US Spec NA Grout consists of specialty blended cements and admixtures to provide maximum flow, shrinkage com-
pensation and extended working times. NA Grout has been specially formulated to exceed the requirements of
AASHTO LRFD Bridge Construction Specifications Table 10.9.3-2 and is a Class C grout in accordance with the Post
Tensioning Institute’s (PTI) guide specification of post tensioned structures. NA Grout complies with ASTM C1107.
Advantages Compressive Strength
E Pumpable fluid grout for very tight clearances (ASTM C942 per PTI GS 4.4.2)
E Non-bleeding Time PSI MPa
E Attains high compressive strengths at specified w/c ratios 1 Day 4,500 31.02
E Extended working time 7 Days 11,000 75.84
E Non-shrink from time of placement 28 Days 15,000 103.42
E Thixotropic: High flow restored by agitation
E
Encapsulates tendons, bolts or bars to protect from corrosion
E
Consistent: Strict Quality Control testing and standards
Packaging and Yield
US Spec NA Grout is packaged in heavy duty, polyethylene lined bags containing 50 lb (22.7 kg), yielding 0.53 cubic
feet when 7.75 quarts of mixing water is used.
Mixing
Mix US Spec Grout to a uniform consistency in accordance with the manufacturer's instructions. Potable water con-
taining no chlorides or other foreign substance shall be used. The water shall be accurately measured and placed in the
mixer first. Start with 1.94 gallons of water per 50lb bag of US Spec NA Grout and mix continuously for 3-5 minutes
before placing. If possible, the grout should be mixed continuously until placing is completed, but if this is not practical,
a brief remixing prior to pumping or placement is adequate to overcome the effect of “thixotropic set”.

T3P Heavy Duty Plastic Grout Tube T4Z Grout Tube Adapter
Furnished in product lengths for the anchors or in For down pressure grouting only when grout is forced
rolls. through normal grout hole in the hollow rebar Spin-Locks.
O.D. I.D.
3/8” 1/4”
(9.5 mm) (6.4 mm)
1/2” 3/8”
(12.7 mm) (9.5 mm)
3/4” 5/8”
(19.1 mm) (15.9 mm)

Super Plasticizer
Plasticizer is available and is used as a water reduc-
er for ease of pumping grout through tubes at lower
water to cement ratios. Super Plasticizer can only be
used with Wil-X Cement Grout.
 Grout Pumps

T6Z-04 Manual Grout Pump T6Z-08 Air Powered Grout Pump

2 stroke position, piston driven pump. Pump cement Pumps cement grout only, no sand mixes. 32 Gallon
grout only, no sand. Use of plasticizer is recommend Mixing Tank. Mixes up to 2 sacks of material at once and
with hand pumps. allows for grout to be pumped during mixing or mixed
Approximate size: 30-3/4” high without pumping.
24-1/4” wide Weight: 560 lbs.
35” high with handle Dimension Size: 50” long
Weight: 60 lbs. (Dry weight) 30.5” wide
Outlet capacity: 40 psi average, 52” high
80 psi maximum Production Rate: 8 gallons per minute at 150 psi
Call your Williams representative for information on the full line of grout pumps and mixers.

Hydraulic Jacks
Tensioning By Jacking
Ram
Tensioning by jacking can be accomplished with Directional Jack Gauge Hex Nut
Lever
the various capacity tensioning jacks shown Hose from
Bottom Fitting
Plate
below. Williams post tensioning jacks are on Jack to Pump

designed to be especially helpful for recessed sit-

uations, while the T7Z Hydraulic Test Jacks are
designed for open areas. Jacks are matched with
Hydraulic
electric or air pumps. Jacks may be purchased or Hydraulic Pump Jack
rented as required. Rental equipment packages (Air or Electric Drive) Hose from Pump to
High Strength
Top Fitting on Jack
include ram on mounted stand, hoses, pull rod, Extension Rod

gauges, power unit and knocker wrench for trans- Base

High Strength
Coupling
ferring the load from the jack to the anchor head.

T7Z Open Frame Hydraulic Jacks

Used for testing and prestressing All-Tread-Bars. Available with up to 5-1/8” center hole. Unit comes with ram, pump,
gauge, hoses, jack stand, high strength coupling, high strength test rod, plate, hex nut and knocker wrench.
Minimum Approx.
Maximum
Jack Pump Ram Base Ram Total Ram Ram Total Ram
Test Rod
Capacity Method Height Size Travel & Frame Area & Frame
Diameter
Height Weight
10 tons Hand 5-5/16” 3” Diameter 2-1/2” 8-3/8” 3/4” 2.12 in2 12 lbs.
(89 kN) Single Acting (135 mm) (76 mm) (64 m) (213 mm) (19 mm) (1,368 mm2) (5.4 kg)
30 tons Hand 6-1/16” 8" x 8" 3” 19” 1-1/4” 5.89 in2 80 lbs.
(267 kN) Single Acting (154 mm) (203 x 203 mm) (76 mm) (483 mm) (32 mm) (3,800 mm2) (36 kg)
60 tons Hand, Air, or Electric 9-1/2" 8" x 8" 5" 29" 2" 12.31 in2 153 lbs.
(534 kN) Double Acting (241 mm) (203 x 203 mm) (127 mm) (737 mm) (51 mm) (7,942 mm2) (69 kg)
100 tons Air or Electric 12-3/8" 9" x 9" 6" 28" 2" 20.03 in2 192 lbs.
(890 kN) Double Acting (314 mm) (228 x 228 mm) (152 mm) (711 mm) (51 mm) (12,923 mm2) (87 kg)
150 tons Air or Electric 12-1/4" 12" x 12" 5" 32-1/4" 2-1/2" 30.1 in2 350 lbs.
(1334 kN) Double Acting (311 mm) (305 x 305 mm) (127 mm) (819 mm) (64 mm) (19,419 mm2) (159 kg)
200 tons Air or Electric 16" 12" x 12" 8" 34" 4" 40.45 in2 518 lbs.
(1779 kN) Double Acting (406 mm) (305 x 305 mm) (203 mm) (864 mm) (102 mm) (26,097 mm2) (235 kg)
300 tons Electric 27-1/2" 15" Dia. 15" 50-1/2" 5-3/8" 78.5 in2 1,400 lbs.
(2670 kN) Double Acting (699 mm) (381 mm) (381 mm) (1283 mm) (137 mm) (50,645 mm2) (635 kg)
400 tons Electric 18-3/4" 15" Dia. 6" 45-3/4" 4-1/4" 91.5 in2 1,300 lbs.
(3558 kN) Double Acting (476 mm) (381 mm) (152 mm) (1162 mm) (108 mm) (59,032 mm2) (590 kg)
Certification of gauge accuracy available on request prior to shipment only.
 Torque Equipment
T8Z Hydraulic Torque Wrench T8Z Torque Wrench Bolt Square Capacity
Diameter Drive Size (ft. lbs.)
The hydraulic torque wrench is used for tensioning For applying torque to 1/2"-1" 3/4" 100-600
anchors in tight fitting locations where it would be difficult the anchor bolt when set- *1-1/8"-2" 1" 200-1,000
to use an hydraulic jack. The wrench is also recom- ting the anchor. *Available with Ratchet Adapter
mended for use when setting the large diameter Spin-
Lock anchors. The torque wrenches are light weight and
can achieve a maximum of 7,400 ft-lbs. All Hydraulic
Torque Wrenches have 1-1/2” square drive outputs.

Maximum Length Height Weight

Torque
5,590 ft./lbs. 11.11" 4.49" 16.75 lbs. T8Z-04 Torque Multiplier (4:1)
(773 kg/M) (279 mm) (114 mm) (7.6 kg)
7,400 ft./lbs. 10.74" 7" 19 lbs.
For use with T8Z Torque Wrench.
(1,023 kg/M) (273 mm) (178 mm) (11.3 kg) Other sizes available.

Size Square Drive Input Square Drive Output Maximum Torque

GA 186 1" 1-1/2" 4,000 ([Link].)

T9F Impact Tool

Lightweight air impact
guns for applying torque to
anchor bolts when setting or
tensioning the anchor assembly.
Bolt Square Capacity
Size Diameter Drive Size (ft. lbs.)
T9F-08 1" to 1-3/8" 1" 1,700 - 2,000
T9F-12 1-3/8" to 2" 1-1/2" 3,000 - 4,000

T1Z & T2Z Long Fitting Tool Adapters

S9Z S-7 Setting Tool For driving hex nuts and setting tools, typically with
Bolt Rod Part Included with each full our Spin-Lock anchor systems. Works with torque
Diameter Number box of anchors up to 1” in wrench or impact gun.
1/2" S9Z-004 diameter. For anchors Available with a 3/4”, 1” or 1-1/2” square drive.
3/4" S9Z-006 above 1” in diameter, use Please specify square drive for compatibility with your
1" S9Z-008 S6Z Spin-Lock Setting equipment.
Tool.

T2Z Regular Socket T1Z Deep Socket

S6Z Spin-Lock Setting Tool

Bolt Rod Part This tool is required K3F-26 Long Fitting Wrench Adapter
Diameter Number for torque setting the
1/2" S6Z-OH-004 For applying torque to
Spin-Lock anchors with-
5/8" S6Z-OH-005 recessed anchor nuts that are
out jamming or scoring
3/4" S6Z-OH-006 under tension when using
the anchor threads.
7/8" S6Z-OH-007 hydraulic jacks. Available in all
Special two piece
1" S6Z-OH-008 anchor sizes.
design allows lower hex
1-1/8" S6Z-OH-009
to be held in place while
1-1/4" S6Z-OH-010
upper hex is loosened
1-3/8" S6Z-OH-011
for easy removal.
T3Z Hex Knocker Wrench
1-1/2" S6Z-OH-012
Hardened steel allows for sever- Hex knocker wrench-
1-3/4" S6Z-OH-014
al reuses. Two piece design es are used for safe hex
1-7/8" S6Z-OH-015
assures easy removal. nut adjustment inside of
2" S6Z-OH-016 open frame jacks.
 All-Thread Torque Tension Charts
R71 150 KSI All-Thread-Bar & R61 Grade 75 All-Thread Rebar Torque Tension Chart
All data based on greased (MolyCoat Gn) threads and surfaces.
ft. - lbs..

Load in Kips
ft. - lbs..

Load in Kips
 Spin-Lock Torque Tension Charts
R1H Hollow-Core, R1V High Impact, R1S High Tensile,
R1J Solid Rebar & R7S 150 KSI Spin-Lock Torque Tension Chart
ft. - lbs..

Load in Kips For R1J bars use R1S values.

ft. - lbs..

Load in Kips For R1J bars use R1S values.

 Williams offers a full line of Ground Anchors, Concrete Anchors, Post-Tensioning Systems,
and Concrete Forming Hardware Systems for whatever your needs may be.

Also available from Williams are Rock & Soil Anchor Sample Specifications and High Capacity Concrete Anchor Sample Specifications

Please see website for most current information

Web: [Link]
E-mail: williams@[Link]
Corporate Headquarters
8165 Graphic Dr.
Belmont, MI 49306
Phone: (616) 866-0815
Fax: (616) 866-1890
251 Rooney Road 2600 Vulcan Dr. 7601 North Columbia
Golden, CO 80401 Lithia Springs, GA 30122 Portland, OR 97203
Phone: (303) 216-9300 Phone: (770) 949-8300 Phone: (503) 285-4548
Fax: (303) 216-9400 Fax: (770) 949-2377 Fax: (503) 285-6858

103 Kestrel Dr. 6440 Flanders Dr. 25232 74th Ave. South
Collegeville, PA 19426 San Diego, CA 92121 Kent, WA 98032
Phone: (610) 489-0624 Phone: (858) 320-0330 Phone: (253) 854-2268
Fax: (610) 489-0629 Fax: (858) 320-0360 Fax: (253) 854-2318

FORM HARDWARE & ROCK BOLT (Canada) LTD.

670 Industrial Road Laval, PQ Vernon, BC
London, ON, N5V 1V1 Phone: (450) 962-2679 Phone: (250) 306-0737
Phone: (519) 659-9444 Fax: (450) 962-2680 Fax: (519) 659-3623
Fax: (519) 659-5880
We have representation in the following organizations: