SP-351 thru SP-354 INFORMATION DISPLAYS 97.381 sp.3s2 97-353 $°-354 4ecpen oes ese es| HORIZONTALLY STACKED DISPLAYS. DISPLAYS SHOWN ACTUAL SIZE APPLICATION AND USE The SP.350 Series Information Displays were designed for interfacing with MOS)LSI. These displays ae recommended for use in all dc or multiplexed applications, with or without suppressed (olanked) ‘The SP-3S0 Series offers the user the advantage of improved electrical characteristics not previously available in displays of this type. These improvements include reduction (1) of the anode voltage required, (2) of the cathode current required, and (3) of the blanking tequitements, In addition, a keepalive cathode provides an internal ion source that reduces refoniration time to les than 30 mero: seconds. allows zero suppreson, and improves the operation ofthe Uipay in ak enitonments nt law temperatures, FEATURES ‘cheroctor Height 0550 inch Color range (Neon Glow) Brightness 210 foot tamber's noms Viewing Ante 130 degrees Viewing Distance an tect Life Expectancy 10 years ‘SPECIFICATIONS DE Characteristics Minimum | Typical Display Supply Vortagel? io weovae | 180 vae ‘Anode-to Cathode Voltage Drop lsegment = 390 HA 198 ve Cathode Current ~ Per Seament (4h raowa | ga0ua | s20ua Cathode Current — Decimal Point? sua | 138ua | 904m Cathode Current — Plus Sign! zeoua | sesua | Arona Cathode Current — Minus Sign? vaoun | 2704 | 80ua Cathode Current — Keop Alive town | Sowa Power Dissigation (With All Seaments Lighted @ 330 1a eypicaibid) 350 mw Operating Temperature 0% 20° Storage Temperature 55°C 125°C ‘Multiplex Choraeterstics Minimam | Typist | Maximum “Anode On TimalS) BO usec | 200 avec Intercigit Blanking Time (isegment™@50H0 2180 V1'5)] 40sec | 55 psec = Retrosn Period “o Note 7 Dinplay Supply Voltage wwovac | aover | Note2 ‘Anode Voltage Swing ove | as voc | 90Vde Cathode Voitage Swing(®) 20 vac] sovae | 125 vae Cathode @iat Vottags ("On Anode x0 “OF govec | sisvie | 125 Vae ‘Cathode Vortagel(®) NOTES: 1. The minimum recommended voltage required to ionize the display is 160 volts de. After the display has ionized, the voltage drop is approximately 135 volts. Typical cathode current of 330 KA Is assuned 2. Display supply voltage (including ripple) should not exceed 200 Vue when display Is used with DD-700 or DD-702 Decoder/Driver. Higher display supply voltages are acceptable when DD-700 or DD-702 ae not used. sf cureat ts limited as speified 3. Lighted cathodes on all digits with independent curcent limiting, For bussed eathodes (multiplexed ‘opecation), 90 volts i permissible 4, The lowest current for even glow on the largest segment is 130 yA. Currents wp to 1.5 times the typical current may be used, however life expectancy may be reduced by operation at excessively higher currents. For multiplexed operation (time shared) segment currents may be increased 10 1-28 Im with 0.25 or smaller diy cycle, 5. Blonking requirements are strongly dependent upon the mode of multiplex operation and upon the segment current used. (See page 35.) ‘Anode On Time assumes typical Keep-alive current and typical anode supply voltages. (See page 36.) Keepaliveisrecommended inall multiplexed applications, Thee (3) millsecondsis maximum without eepalive. Ten (10) milliseconds is typical with keep alive The combination of Cathode Bias Voltage and Cathode Voltage Swing display supply voltage Under specific conditions, Cathode Voltage Swings of as low as 30 volts are acceptable 6 be within recommendedSEGMENT DESIGNATIONS AND PIN CONNECTIONS > > fd secaagumineee ee DIGIT DESIGNATIONS IN DESIGNATIONS AND LOCATIONS notes: 1. Allaigit and pin designations and pin locations at viewed from the font ofthe display. Shaded areas indicate anode pater 2 Distance from digit centerine toe of ply ts measured from pln No.7 3, Pin focatans shown are nominal (approximately £0.003" tolerance), Ailowances should be made fr location tolerance by sizeof pe board hole lm Foren ofr nd lel, aeommend tou ee dan ay 4. Foren centerine spacing o digs in separate envelopes, recommend that comparable pinson adjacent digits should he space nine. ‘Allow 0.030 inch between jacentigpy envelopes Tor ene‘ sertion” and compensate for taleranets in ect board manufactur 5 Both maximum dimensions cannot occur simultaneoualy. The 0.120" overall height applies.