HARCO PVC IPS GASKETED FITTINGS

DESIGN DATA
Applicable Standards TEE (GxGxG)
Materials: ASTM D-1784, NSF 14 L
Joints: ASTM D-3139
Gaskets: ASTM F-477
Wall Thickness: SDR-21
NSF 14 Certification.
A
BELL SPECIFICATIONS
A
B

SIZE PART No. STYLE A L WT. (approx.)

Spigot
1½x1½ 112-150 F 6.0 9.1 1.0
C
O.D. 2x1½ 112-215 H 6.1 9.1 1.3
2x2 112-220 H 6.1 9.1 1.4
2½x1½ 112-251 A 8.4 9.9 1.4
2½x2 112-252 H 6.8 9.9 2.0
SIZE STYLE A B C Spigot O.D. 2½x2½ 112-255 H 6.8 9.9 1.7
1½ H 3.17 2.42 2.8 1.90 3x1½ 112-315 A 9.4 10.9 2.5
2 H 3.27 2.52 3.3 2.38 3x2 112-320 H 7.7 11.4 2.8
2½ H 3.38 2.63 3.8 2.88 3x2½ 112-325 H 8.0 11.9 3.1
3 H 3.52 2.77 4.5 3.50 3x3 112-330 H 7.7 10.9 2.8
4 H 4.10 2.99 5.9 4.50 4x2 112-420 H 8.6 13.1 4.3
6 H 4.57 3.46 8.3 6.63 4x2½ 112-425 H 8.5 13.1 4.9
8 H 5.16 3.90 10.4 8.63 4x3 112-430 H 8.8 13.1 4.9
10 Fab 5.75 4.70 11.5 10.75 4x4 112-440 H 9.3 13.1 5.6
12 Fab 6.15 4.90 12.0 12.75 5x5 112-550 F 11.0 14.8 10.0
6x2 112-620 A 12.2 11.6 2.8
NOTES: 6x3 112-630 H 11.5 12.5 3.0
• All lay lengths & weights are approximate and are subject to 6x4 112-640 H 11.8 16.3 11.0
change without notice. 6x6 112-660 H 11.5 16.4 12.3
• Fabricated fitting configurations may vary. 8x4 112-840 H 13.9 19.5 18.7
STYLE LEGEND: 8x6 112-860 H 14.4 19.5 19.3
H ----- Harco style one piece molded. 8x8 112-880 H 14.9 19.5 21.3
HB --- Harco style one piece molded, reduced by use of flush style REDUCER (SxG)
thd x thd bushing. L
F ----- Flo style one piece molded.
FB --- Flo style one piece molded, reduced by use of flush style thd
x thd bushing.
C –--- Manufactured by Certain-Teed Corporation.
A –--- Assembled using one piece molded fitting with MIPT x A
Gasketed adapter or Spigot adapter for branch or BELL.
Fab – Fabricated using SCH-40 PVC fittings with Harco Spigot
adapters (or pipe) solvent welded together. (See pressure
rating warning on this page.) SIZE PART No. STYLE A L WT. (appox.)
2x1½ 116-215 F 2.8 7.0 0.5
Warning: Cyclical pressure surges (WATER HAMMER) can
reduce the life of PVC fittings. Where such conditions may exist, 2½x2 116-252 F 3.4 7.0 0.8
HARCO DEEP BELL DUCTILE IRON FITTINGS for IPS size PVC 3x2 116-320 F 3.7 7.9 0.9
pipe should be considered. HARCO DEEP BELL DUCTILE IRON 3x2½ 116-325 F 4.2 7.4 1.3
FITTINGS are available in sizes 1½” through 12”. 4x2 116-420 F 4.7 10.0 1.5
4x2½ 116-425 F 5.0 8.3 1.8
Fab Style: These fittings use SCH-40 PVC fittings. SCH-40 PVC 4x3 116-430 F 4.7 10.1 1.9
fittings do not have a long term pressure rating. See section 6.3.2 5x4 116-540 F 5.8 7.8 3.0
of ASTM D2466-97. Use of these fittings in pressure systems is at
6x3 116-630 F 7.0 9.0 3.5
user’s risk.
6x4 116-640 H 6.9 8.0 2.7
The use of anything but properly designed and installed thrust 6x5 116-650 Fab 7.0 10.0 4.9
blocks will reduce the life of plastic fittings. Thrust blocks must be 8x6 116-860 H 9.0 9.3 5.8
poured concrete only and sized for the soil conditions. Joint
restraint products are available. CALL FOR OTHER SIZES, CONFIGURATIONS & GASKET MATERIALS.

THE HARRINGTON CORPORATION

P.O. BOX 10335 • LYNCHBURG VIRGINIA 24506 • PLANT 3721 COHEN PLACE • LYNCHBURG VIRGINIA 24501
PHONE: (434) 845-7094 • FAX: (434) 845-8562 • E-mail: [email protected]
Form 138 – 4/30/01
 HARCO PVC IPS GASKETED FITTINGS
DESIGN DATA
Applicable Standards GASKET x FEMALE NPT ADAPTER
Materials: ASTM D-1784, NSF 14 L
Joints: ASTM D-3139
Gaskets: ASTM F-477
Wall Thickness: SDR-21 A
NSF 14 Certification.

NOTES: SIZE PART No. STYLE A L WT. (approx.)

• All lay lengths & weights are approximate and are subject to 1½ 132-015 Fab 2.7 5.7 0.5
change without notice. 2 132-020 Fab 3.3 6.1 0.7
• Fabricated fitting configurations may vary. 2½ 132-025 Fab 3.8 7.3 1.2
3 132-030 Fab 4.5 7.5 1.5
STYLE LEGEND:
H ----- Harco style one piece molded. 4 132-040 Fab 5.8 9.4 2.6
HB --- Harco style one piece molded, reduced by use of flush style 5 132-050 Fab 7.0 10.5 5.0
thd x thd bushing. 6 132-060 Fab 8.1 12.1 6.0
F ----- Flo style one piece molded. PE (Plain End) x MALE NPT ADAPTER
FB --- Flo style one piece molded, reduced by use of flush style thd
x thd bushing. L
C –--- Manufactured by Certain-Teed Corporation.
A –--- Assembled using one piece molded fitting with MIPT x
Gasketed adapter or Spigot adapter for branch or BELL.
Fab – Fabricated using SCH-40 PVC fittings with Harco Spigot A
adapters (or pipe) solvent welded together. (See pressure
rating warning on this page.)
Warning: Cyclical pressure surges (WATER HAMMER) can SIZE PART No. STYLE A L WT. (appox.)
reduce the life of PVC fittings. Where such conditions may exist, 1½ 133-015 Fab 2.2 5.2 0.3
HARCO DEEP BELL DUCTILE IRON FITTINGS for IPS size PVC 2 133-020 H 2.6 4.1 0.3
pipe should be considered. HARCO DEEP BELL DUCTILE IRON 2½ 133-025 Fab 3.3 6.3 0.8
FITTINGS are available in sizes 1½” through 12”. 3 133-030 Fab 4.0 6.9 1.3
Fab Style: These fittings use SCH-40 PVC fittings. SCH-40 PVC 4 133-040 Fab 5.0 7.5 2.0
fittings do not have a long term pressure rating. See section 6.3.2 6 133-060 Fab 7.3 9.8 5.3
of ASTM D2466-97. Use of these fittings in pressure systems is at SPIGOT x GASKET ADAPTER
user’s risk.
L
The use of anything but properly designed and installed thrust B
blocks will reduce the life of plastic fittings. Thrust blocks must be
poured concrete only and sized for the soil conditions. Joint
restraint products are available.
A

SIZE PART No. STYLE A B L WT. (appox.)

1½ 130-015 H 2.7 1.1 4.5 0.3
2 130-020 H 3.3 1.4 4.9 0.5
2½ 130-025 H 3.8 2.0 5.3 0.7
3 130-030 H 4.5 2.0 5.8 0.9
4 130-040 H 5.9 2.3 6.4 1.7
5 130-050 F 7.0 3.0 9.1 3.0
6 130-060 H 8.3 3.0 8.0 3.8

CALL FOR OTHER SIZES, CONFIGURATIONS & GASKET MATERIALS.

THE HARRINGTON CORPORATION

P.O. BOX 10335 • LYNCHBURG VIRGINIA 24506 • PLANT 3721 COHEN PLACE • LYNCHBURG VIRGINIA 24501
PHONE: (434) 845-7094 • FAX: (434) 845-8562 • E-mail: [email protected]
Form 139 – 4/30/01
 HARCO PVC IPS GASKETED FITTINGS
DESIGN DATA
Applicable Standards SERVICE TEE (GxGxFIPT)(Treaded NPT Thread)
Materials: ASTM D-1784, NSF 14 L
Joints: ASTM D-3139
Gaskets: ASTM F-477
Wall Thickness: SDR-21
NSF 14 Certification.

NOTES: SIZE PART No. STYLE L WT. (approx.)

• All lay lengths & weights are approximate and are subject to 1½x¾ 151-153 FB 8.5 0.8
change without notice. 1½x1 151-154 F 8.5 0.8
• Fabricated fitting configurations may vary. 1½x1¼ 151-155 Fab 10.9 0.8
2x½ 151-202 HB 9.2 1.2
STYLE LEGEND:
2x¾ 151-203 H 9.2 1.2
H ----- Harco style one piece molded.
2x1 151-204 H 9.2 1.2
HB --- Harco style one piece molded, reduced by use of flush style
thd x thd bushing. 2x1¼ 151-205 H 9.2 1.2
F ----- Flo style one piece molded. 2x1½ 151-206 H 9.2 1.2
FB --- Flo style one piece molded, reduced by use of flush style thd 2½x½ 151-252 HB 9.9 1.5
x thd bushing. 2½x¾ 151-253 HB 9.9 1.5
C –--- Manufactured by Certain-Teed Corporation. 2½x1 151-254 H 9.9 1.5
A –--- Assembled using one piece molded fitting with MIPT x 2½x1¼ 151-255 H 9.9 1.5
Gasketed adapter or Spigot adapter for branch or BELL. 2½x1½ 151-256 H 9.9 1.5
Fab – Fabricated using SCH-40 PVC fittings with Harco Spigot 2½x2 151-258 H 9.9 1.5
adapters (or pipe) solvent welded together. (See pressure 3x½ 151-302 HB 11.0 2.5
rating warning on this page.) 3x¾ 151-303 HB 11.0 2.5
Warning: Cyclical pressure surges (WATER HAMMER) can 3x1 151-304 H 11.0 2.5
reduce the life of PVC fittings. Where such conditions may exist, 3x1¼ 151-305 H 11.0 2.5
HARCO DEEP BELL DUCTILE IRON FITTINGS for IPS size PVC 3x1½ 151-306 H 11.0 2.5
pipe should be considered. HARCO DEEP BELL DUCTILE IRON 3x2 151-308 H 11.0 2.5
FITTINGS are available in sizes 1½” through 12”. 4x½ 151-402 HB 10.7 3.1
4x¾ 151-403 HB 10.7 3.1
Fab Style: These fittings use SCH-40 PVC fittings. SCH-40 PVC
4x1 151-404 H 10.7 3.1
fittings do not have a long term pressure rating. See section 6.3.2
4x1¼ 151-405 H 10.7 3.1
of ASTM D2466-97. Use of these fittings in pressure systems is at
4x1½ 151-406 H 10.7 3.1
user’s risk.
4x2 151-408 H 10.7 3.1
The use of anything but properly designed and installed thrust 6x½ 151-602 HB 9.3 5.8
blocks will reduce the life of plastic fittings. Thrust blocks must be 6x¾ 151-603 HB 9.3 5.8
poured concrete only and sized for the soil conditions. Joint 6x1 151-604 HB 9.3 5.8
restraint products are available. 6x1¼ 151-605 HB 9.3 5.8
6x1½ 151-606 H 9.3 5.8
6x2 151-608 H 11.5 5.8
SWING JOINT TEE (GxGxACME) (315psi rated)
L

SIZE PART No. STYLE A L WT. (approx.)

2x1 153-204 H 4.5 9.2 1.4
2x1¼ 153-205 H 4.5 9.2 1.4
2x1½ 153-206 H 4.5 9.2 1.5
2½x1 153-252 H 4.4 9.6 1.9
2½x1¼ 153-255 H 4.4 9.6 1.9
2½x1½ 153-256 H 4.4 9.6 1.9
CALL FOR OTHER SIZES, CONFIGURATIONS & GASKET MATERIALS.

THE HARRINGTON CORPORATION

P.O. BOX 10335 • LYNCHBURG VIRGINIA 24506 • PLANT 3721 COHEN PLACE • LYNCHBURG VIRGINIA 24501
PHONE: (434) 845-7094 • FAX: (434) 845-8562 • E-mail: [email protected]
Form 140 – 4/30/01
 HARCO PVC IPS GASKETED FITTINGS
DESIGN DATA
Applicable Standards CAP (Gasket)
Materials: ASTM D-1784, NSF 14 L
Joints: ASTM D-3139
Gaskets: ASTM F-477
Wall Thickness: SDR-21
A
NSF 14 Certification.

CROSS (GxGxGxG)
L
Poured concrete thrust blocks only.
SIZE PART No. STYLE A L WT. (approx.)
1½ 149-015 Fab 2.8 5.3 0.5
2 149-020 H 3.3 3.7 0.5
2½ 149-025 Fab 3.8 6.4 1.0
3 149-030 Fab 4.5 6.7 1.4
L 4 149-040 Fab 5.9 7.6 2.7
5 149-050 Fab 7.0 10.0 4.4
6 149-060 Fab 8.5 9.8 6.9
NON_PRESSURE WYE (GxGxG)
L

SIZE PART No. STYLE L WT. (approx.)

1½ 153-015 Fab 11.6 1.7
2 153-020 Fab 12.1 3.4
2½ 153-025 Fab 14.3 4.4 C

3 153-030 Fab 15.1 5.3

4 153-040 Fab 17.9 9.0

NOTES:
• All lay lengths & weights are approximate and are subject to
change without notice.
• Fabricated fitting configurations may vary.
STYLE LEGEND: SIZE PART No. STYLE C L WT. (appox.)
H ----- Harco style one piece molded. 3x3 101-0303 Fab 6.8 10.1 5.0
HB --- Harco style one piece molded, reduced by use of flush style 4x4 101-0404 Fab 8.4 12.3 10.0
thd x thd bushing.
F ----- Flo style one piece molded. GASKET x MALE NPT ADAPTER
FB --- Flo style one piece molded, reduced by use of flush style thd Do not use joint restraint.
x thd bushing. L
C –--- Manufactured by Certain-Teed Corporation.
A –--- Assembled using one piece molded fitting with MIPT x
Gasketed adapter or Spigot adapter for branch or BELL.
Fab – Fabricated using SCH-40 PVC fittings with Harco Spigot A
adapters (or pipe) solvent welded together. (See pressure
rating warning on this page.)
Warning: Cyclical pressure surges (WATER HAMMER) can Size on size and reducing sizes of these adapters also available in
reduce the life of PVC fittings. Where such conditions may exist, Harco ductile iron.
HARCO DEEP BELL DUCTILE IRON FITTINGS for IPS size PVC
SIZE PART No. STYLE A L WT. (approx.)
pipe should be considered. HARCO DEEP BELL DUCTILE IRON
FITTINGS are available in sizes 1½” through 12”. 1½x1¼ 131-012 Fab 2.8 6.0 0.5
1½ 131-015 H 2.8 4.3 0.5
Fab Style: These fittings use SCH-40 PVC fittings. SCH-40 PVC 2 131-020 H 3.3 4.6 0.5
fittings do not have a long term pressure rating. See section 6.3.2 2½ 131-025 H 3.8 4.8 1.2
of ASTM D2466-97. Use of these fittings in pressure systems is at
3 131-030 H 4.5 5.0 1.5
user’s risk.
4 131-040 Fab 5.9 8.5 2.8
The use of anything but properly designed and installed thrust 5 131-050 F 3.0
blocks will reduce the life of plas tic fittings. Thrust blocks must be 6 131-060 Fab 8.3 10.9 10.3
poured concrete only and sized for the soil conditions. Joint
restraint products are available. CALL FOR OTHER SIZES, CONFIGURATIONS & GASKET MATERIALS.

THE HARRINGTON CORPORATION

P.O. BOX 10335 • LYNCHBURG VIRGINIA 24506 • PLANT 3721 COHEN PLACE • LYNCHBURG VIRGINIA 24501
PHONE: (434) 845-7094 • FAX: (434) 845-8562 • E-mail: [email protected]
Form 141 – 4/30/01
 HARCO PVC IPS GASKETED FITTINGS
DESIGN DATA
Applicable Standards 90° BEND (GxG)
Materials: ASTM D-1784, NSF 14 L
Joints: ASTM D-3139
Gaskets: ASTM F-477
Wall Thickness: SDR-21
NSF 14 Certification. L
B
GASKET x FLANGE ADAPTER
L
B
SIZE PART No. STYLE B L WT. (approx.)
1½ 118-015 F 1.0 4.8 0.6
2 118-020 H 1.3 6.2 0.8
B A
2½ 118-025 H 1.6 6.8 1.3
3 118-030 H 2.0 7.7 1.8
4 118-040 H 2.5 9.5 3.8
6 118-060 H 3.6 12.3 9.0
SIZE PART No. STYLE A B L WT. (approx.) 8 118-080 H 4.5 14.9 16.3
1½ 154-015 Fab 5.0 3.9 4.8 0.8 45° BEND (GxG)
2 154-020 Fab 6.0 4.8 5.1 1.2 L
2½ 154-025 Fab 7.0 5.5 5.8 1.7
3 154-030 Fab 7.5 6.0 6.0 2.4
4 154-040 Fab 9.0 7.5 7.0 6.0
6 154-060 Fab 11.0 9.5 8.3 12.0 A
8 154-080 Fab 13.5 11.8 17.7 20.0
B
NOTES:
B
• All lay lengths & weights are approximate and are subject to
change without notice. SIZE PART No. STYLE A B L WT. (appox.)
• Fabricated fitting configurations may vary. 1½ 122-015 Fab 5.8 0.9 9.1 0.9
2 122-020 H 5.3 0.6 7.8 0.8
STYLE LEGEND:
2½ 122-025 H 6.1 0.7 8.3 1.1
H ----- Harco style one piece molded.
3 122-030 H 6.6 0.9 9.1 1.6
HB --- Harco style one piece molded, reduced by use of flush style
thd x thd bushing. 4 122-040 H 8.4 1.1 11.0 3.4
F ----- Flo style one piece molded. 6 122-060 H 11.3 1.6 13.6 7.8
FB --- Flo style one piece molded, reduced by use of flush style thd 8 122-080 H 13.8 2.0 15.8 13.3
x thd bushing.
C –--- Manufactured by Certain-Teed Corporation.
A –--- Assembled using one piece molded fitting with MIPT x 22½° BEND
Gasketed adapter or Spigot adapter for branch or BELL.
Fab – Fabricated using SCH-40 PVC fittings with Harco Spigot
adapters (or pipe) solvent welded together. (See pressure
rating warning on this page.)
Warning: Cyclical pressure surges (WATER HAMMER) can
reduce the life of PVC fittings. Where such conditions may exist,
HARCO DEEP BELL DUCTILE IRON FITTINGS for IPS size PVC B
B
pipe should be considered. HARCO DEEP BELL DUCTILE IRON
FITTINGS are available in sizes 1½” through 12”. SIZE PART No. STYLE B WT. (approx.)
2 124-020 Fab 2.0 2.0
Fab Style: These fittings us e SCH-40 PVC fittings. SCH-40 PVC
2½ 124-025 Fab 2.0 3.0
fittings do not have a long term pressure rating. See section 6.3.2
3 124-030 Fab 2.3 3.0
of ASTM D2466-97. Use of these fittings in pressure systems is at
4 124-040 Fab 2.6 5.0
user’s risk.
6 124-060 Fab 4.3 11.0
The use of anything but properly designed and installed thrust
blocks will reduce the life of plastic fittings. Thrust blocks must be
poured concrete only and sized for the soil conditions. Joint CALL FOR OTHER SIZES, CONFIGURATIONS & GASKET MATERIALS.
restraint products are available.

THE HARRINGTON CORPORATION

P.O. BOX 10335 • LYNCHBURG VIRGINIA 24506 • PLANT 3721 COHEN PLACE • LYNCHBURG VIRGINIA 24501
PHONE: (434) 845-7094 • FAX: (434) 845-8562 • E-mail: [email protected]
Form 142-5 – 4/30/01
 HARCO PVC IPS GASKETED FITTINGS
DESIGN DATA
Applicable Standards LINE COUPLING (w/ Stop)
Materials: ASTM D-1784, NSF 14 L
Joints: ASTM D-3139
Gaskets: ASTM F-477
Wall Thickness: SDR-21
NSF 14 Certification. A

PLUG (Spigot)
SIZE PART No. STYLE A L WT. (approx.)
L 1½ 108-015 H 2.8 6.5 0.5
2 108-020 H 3.3 6.7 0.7
2½ 108-025 H 3.8 7.0 0.9
3 108-030 H 4.5 7.2 1.3
A 4 108-040 H 5.9 8.3 2.7
6 108-060 H 8.3 9.3 5.6
8 108-080 H 10.4 11.1 10.3
10 108-100 C 11.5 11.5 14.0
Poured concrete thrust blocks only. 12 108-120 C 12.0 12.0 22.0
SIZE PART No. STYLE A L WT. (appox.)
REPAIR COUPLING (No Stop) HARCO STYLE
1½ 144-015 Fab 2.7 5.2 0.2
L
2 144-020 H 3.0 2.7 0.2
2½ 144-025 Fab 3.4 5.3 0.8
3 144-030 H 3.8 3.5 0.4
4 144-040 H 5.0 3.5 0.4
6 144-060 H 6.8 5.4 2.3 A
8 144-080 H 8.9 6.4 3.8

NOTES: SIZE PART No. STYLE A L WT. (appox.)

• All lay lengths & weights are approximate and are subject to 1½ 109-015 H 2.8 6.5 0.5
change without notice. 2 109-020 H 3.3 7.8 0.7
• Fabricated fitting configurations may vary. 2½ 109-025 H 3.8 8.4 0.9
3 109-030 H 4.5 9.0 1.3
STYLE LEGEND:
4 109-040 H 5.9 10.6 2.7
H ----- Harco style one piece molded.
5 109-050 H 7.0 11.2 4.1
HB --- Harco style one piece molded, reduced by use of flush style
6 109-060 H 8.3 11.6 5.6
thd x thd bushing.
F ----- Flo style one piece molded. 8 109-080 H 10.4 11.1 10.3
FB --- Flo style one piece molded, reduced by use of flush style thd 10 109-100 C 11.5 11.5 14.0
x thd bushing. 12 109-120 C 12.0 12.0 22.0
C –--- Manufactured by Certain-Teed Corporation.
A –--- Assembled using one piece molded fitting with MIPT x REPLACEMENT GASKET HARCO STYLE
Gasketed adapter or Spigot adapter for branch or BELL.
Fab – Fabricated using SCH-40 PVC fittings with Harco Spigot
adapters (or pipe) solvent welded together. (See pressure
rating warning on this page.)
Warning: Cyclical pressure surges (WATER HAMMER) can
reduce the life of PVC fittings. Where such conditions may exist,
HARCO DEEP BELL DUCTILE IRON FITTINGS for IPS size PVC SIZE PART No. WT. (approx.)
pipe should be considered. HARCO DEEP BELL DUCTILE IRON 1½ 195.015 0.1
FITTINGS are available in sizes 1½” through 12”.
2 195-020 0.1
Fab Style: These fittings use SCH-40 PVC fittings. SCH-40 PVC 2½ 195-025 0.1
fittings do not have a long term pressure rating. See section 6.3.2 3 195-030 0.1
of ASTM D2466-97. Use of these fittings in pressure systems is at 4 195-040 0.2
user’s risk. 6 195-060 0.3
The use of anything but properly designed and installed thrust 8 195-080 0.3
blocks will reduce the life of plastic fittings. Thrust blocks must be
CALL FOR OTHER SIZES, CONFIGURATIONS & GASKET MATERIALS.
poured concrete only and sized for the soil conditions. Joint
restraint products are available.

THE HARRINGTON CORPORATION

P.O. BOX 10335 • LYNCHBURG VIRGINIA 24506 • PLANT 3721 COHEN PLACE • LYNCHBURG VIRGINIA 24501
PHONE: (434) 845-7094 • FAX: (434) 845-8562 • E-mail: [email protected]
Form 142-6 – 3/6/02