DL321 TOP HAMMER

LONGHOLE DRILL
TECHNICAL SPECIFICATION

Sandvik DL321 is a fully-mechanized and compact KEY FEATURES

electro-hydraulic top hammer longhole drill designed Hydraulic rock drill HL820ST (21 kW)
for underground mass mining in 3.2 x 3.2 m or larger Drilling module LFRC700 (20 + 1 rods)
production drifts. It is capable of drilling vertical Rod length 4’ - 6’ (1 220 - 1 830 mm)
and inclined fans and single or parallel Ø64…89 mm Boom ZR20 (on horseshoe stabilizer)
longholes up to 38 meters in depth, using T38, T45 and Minimum drift size (H and W) 3 150 - 3 750 mm
T51 MF-rods or Ø65 mm tube rods. Drift width in T-section 3.4 m (minimum)
The DL321 is mounted on a 4-wheel drive frame-steered Pivot point height 1 630 - 2 115 mm
and diesel-powered carrier. It is equipped with the Boom coverage (vertical holes) 2 000 mm
HL820ST hydraulic rock drill, LFRC700 drilling module, Transport height 2 920 - 3 450 mm
ZR20 telescopic boom, TAS drilling control system and Transport width 1 990 mm
FOPS / ROPS operator’s safety cabin for high drilling Transport length 9 920 mm
capacity and maximum uptime. The 360° drilling module Transport weight 17 000 kg
rotation and wide boom swing and tilt angles make
the unit suitable for most mining methods and various ROCK TOOLS AND HOLE LENGTH
service support applications. The CANbus based TAS Maximum hole length (m)*
Rod Ø Hole Ø
drilling control system with the user-friendly operating Type
(mm) (mm) 4’ rods 5’ rods 6’ rods
interface and various instrumentation and automation T35 39 54
levels allow maximum productivity and good drilling T38 39 64
accuracy. T45 46 76 25.3 31.7 38.1
The layout of the NC5 carrier is designed for good T45 65 (tube) 76
visibility and stability, ensuring safe tramming in narrow T51 52 89
mine drifts. The operating and maintenance interface *) Feed in contact with rock and front stinger retracted
are designed for easy access and all service points are
accessible from ground level.

1. DL321 TOP HAMMER - LONGHOLE DRILL

HYDRAULIC ROCK DRILL DRILLING CONTROL SYSTEM
Type of rock drill HL820ST (TS2-301) Type of control system TAS
Percussion power 21 kW Operating principle CANbus
Percussion pressure Up to 200 bar Control panel In safety cabin or canopy
Percussion rate 42 - 52 Hz Adjustable parameters Full percussion
Stabilizer Sleeve type Collaring
Rotation speed 0 – 180 rpm (OMT200) Rotation / Threading
Rotation torque 1 095 Nm (OMT200) Feed / Anti-jamming
Weight 260 - 305 kg Flushing
Length with shank adapter 1 241 mm Rotation pressure controlled feed With One-hole / Fan automation
Diagnostics system Interactive
DRILLING MODULE
Drilling module type LFRC700 (TS2-341) ELECTRIC SYSTEM
Rod length 1 220 - 1 830 mm (4’ - 6’) Standard voltages 380 - 690 V (50 or 60 Hz)
Storing capacity 20 + 1 rods (all threads) Total installed power 92 kW
Retaining centralizer Pito 7 Main switch gear MSE / MSC
Cuttings diverter CC705 IP classification Specification TS2-132
Set-off from stope face 1 950 mm (minimum) Allowed voltage fluctuation ± 10%
Feed force 31 kN Starting method Star-Delta (380 - 690 V)
Feed and return speed 0.3 m/s (fast feed) Automatic cable reel TCR1
Front stinger extension 2 000 mm Cable reel remote control At operator station and cable reel
Front and rear lights 8 x 50 W (24 V) LED
DRILLING MODULE DIMENSIONS Carrier positioning lights 2 x Laser type
Type Rod length Total length Sealed AGM batteries 2 x 12 V (85 Ah)
LFRC704 1 220 mm 2 940 mm
LFRC705 1 525 mm 3 240 mm AIR AND WATER SYSTEM
LFRC706 1 830 mm 3 550 mm Flushing of holes By water
Water booster pump type WBP2 (4 kW / 50 Hz)
LONGHOLE BOOM 100 l/min at 15 bar
Water pump capacity
Telescopic boom ZR20 (TS2-287) (inlet pressure = 4 bar)
Boom swing Left 38° / Right 38° Water pump inlet pressure 2 - 7 bar
Boom (fan) tilt Back 20° / Forward 45° Flushing water pressure 10 - 20 bar
Drilling module roll-over 360° Air compressor CTN10 (1.0 m³/min at 7 bar)
Boom extension 485 mm Shank lubrication device SLU1 (air / oil mist)

Drilling module travel 985 mm (4’ rods) Rock drill air consumption 200 - 300 l/min
1 050 mm (5’ rods) Rock drill oil consumption 250 - 550 g/h
1 200 mm (6’ rods) Air cleaner for external air supply IP5 including connection
Boom coverage (vertical holes) 2 000 mm
Pivot point height (boom vertical) 1 630 - 2 115 mm OPERATOR’S SAFETY CABIN
Rear stinger Mounted on feed cradle Cabin certification FOPS / ROPS (ISO3449)
Rear stinger extension 1 500 mm Type of cabin Low height
Laser distance from drill center 1 400 mm (vertical holes) Unit height in tramming 2 670 mm
Cabin inside height 1 800 mm
HYDRAULIC SYSTEM Cabin < 80 dB(A)
Sound pressure level EN791
Type of hydraulic system TPC LH Emitted 115 dB(A)
Operating principle Electric pilot control Operator’s seat Ergonomic T-back seat
Power pack HPP875 (75 kW) Air conditioning system For drilling and tramming
Filtration (pressure / return) 20µ / 10µ Cabin safety grill For front screen
Oil tank volume 180 liters CD / MP3-player, radio and
Audio system
Cooler for hydraulic oil OW45 oil-to-water (45 kW) loudspeakers
Low oil level indication Low level oil switch

2. DL321 TOP HAMMER - LONGHOLE DRILL

CARRIER OPTIONAL ITEMS
Type of carrier NC5 (frame-steered) Electric system
Carrier articulation ± 40º *Voltage option 1 000 V (50 or 60 Hz) with DOL
Rear axle oscillation ± 10º starter
Dewatering pump outlet Site voltage 380 - 690 V (8 kW),
Ground clearance 320 mm readiness excluding USA/CAN
Diesel engine Deutz TCD2012 (74 kW Tier3) Electric cables Specification TS2-121
Exhaust catalyzer Standard Ground fault and overcurrent unit VYK (excluding USA/CAN)
Outlet on carrier 110 V 16 A, single phase, 1.6 kW
Transmission Hydrostatic Outlet on carrier 230 V 16 A, single phase, 2 kW
Axles Spicer 112 (front) and 123 (rear) Amber flashing light LED (24 V)
Tires 12.00 – 20 Battery jump start CAT

Service brakes Hydraulically applied wet disc brakes Air and water system
Parking / emergency brakes SAHR fail safe type wet disc brakes *Air compressor CT28 (2.8 m³/min, 18.5 kW)
Air mist flushing kit For external air and water supply
Tramming speed Horizontal (0%): 12 km/h Compressed air outlet Quick coupling for pneumatic
8°=1:7=14%: 5 km/h tools
Gradeability / sideways tilt Max. 15° / 5° 2 x 60 liters air receivers For end-of-hole flushing (re-
quires CT28)
Front (horseshoe) stabilizer Hooks and water hose Ø38 mm hose (length 30 m)
Carrier stabilization
2 x hydraulic jacks (rear) Water hose reel and hose THR and Ø38 mm hose (length
Fuel tank 80 liters 60 m)
Tramming oil tank 55 liters
Operator’s safety cabin or canopy
Filling pump for hydraulic oil Electric *Safety canopy and safety grill FOPS (ISO3449)
Hand held fire extinguisher 7.7 or 9 kg (type ABC) Cabin heating system For drilling and tramming
(Webasto)
Brake release By manual hand pump
Tramming alarm Standard
Fire suppression system
Tramming cameras Front, side and rear Spare hand held fire extinguisher 1 x 7.7 kg or 9 kg (type ABC)
Colour scheme Sandvik standard Automatic fire suppression system Sandvik Eclipse™
Manual or automatic system Ansul (6 nozzles)
Documentation 2 x Operator’s manual
2 x Maintenance manual
2 x Technical manual (in English only) Carrier
2 x Parts manual (in English only) *Foam filled tires 4 pcs
2 x Toolman CD Fast filling and evacuation system Wiggins (complete)
Wheel chocks and holders 2 pcs

OPTIONAL ITEMS Extra items

Drilling system Spare rock drill HL820ST or HL710S
*HL710S rock drill With 55 kW or 75 kW power pack Spare wheel assembly Standard or foam filled tires
Spare remote control panel For offboard use Special tools for rock drill Field kit or complete set
Drilling module wear parts kit For alternative tools 3’ drilling module LFRC1503 (27+1 rods)
*Power extractor For HL820ST and HL710S Warranty extension One year (excl. Kazakhstan)
Documentation Extra manuals
Instrumentation Package: Country specific options LAM, CAN, USC, AUS, EUR
Access detector or protector Mandatory in Europe (TS2-211) Package: Harsh water Basic or Advanced (TS2-049)
Drilling instrument TMS For DL300-series (TS2-122) Package: Onboard air and water Specification TS2-328
Spirit level angle indicators 2 pcs (on feed and boom) supply
OptiMine™ remote monitoring For data management
*) replaces standard feature
Automation
Rod handler sequence control Specification TS2-197
One-hole automation Including TMS (TS2-198)
Fan automation Including TMS (TS2-199)
Data transfer (USB/WLAN) Excluding drill plan software

Cleaning system
Low pressure system with reel Up to 15 bar (TS2-343)
High pressure system with reel Up to 220 bar (TS2-343)

Greasing systems
Automatic system Lincoln (for carrier, boom and rod
handler)
Carrier centralized greasing Specification 5-2110
points
Manual system Specification 5-2110

3. DL321 TOP HAMMER - LONGHOLE DRILL

 MINIMUM PRODUCTION DRIFT SIZE (mm)*
Module H W WP HR
LFRC704 3 380 3 150 1 460 1 630
Parallel LFRC705 3 680 3 450 1 760 1 630
LFRC706 3 980 3 750 2 000 1 630
*) 100 mm clearance, add 400 mm (total) for fan automation
Front stinger
extension MAXIMUM PRODUCTION DRIFT SIZE (mm)**
2 000 mm Module H W WP HR
LFRC704 3 700 4 800 2 000 1 750
LFRC705 4 000 5 100 2 000 1 750
LFRC706 4 150 5 250 2 000 1 750

TS2-245:07/ENG/METRIC © Sandvik Mining and Rock Technology 2018 SANDVIK is a registered trademark owned by Sandvik Intellectual Property AB in Sweden and other countries.
**) Rear stinger extended; the use of drilling module mounted
front stinger extends the coverage further
HR

All dimensions in mm

WP
W

SANDVIK
HF

321
SANDVIK

2 670 HB

321
DLDL
1 480
27°
16° 13°

9 920
45°
20°

LF
3 100
SANDVIK

360°
DL 321

2 145
1 630

1 990 30° 20°

240 2 985 3 100
LF
180 9 820
c

Drilling
module HB HF LF C R1 R2
LFRC704 2 920 2 920 2 940 3 550 6 000 3 000
LFRC705 2 920 3 100 3 240 3 800 6 150 2 850
LFRC706 3 020 3 450 3 550 4 050 6 300 2 700

Sandvik Mining and Rock Technology reserves the right to make changes to the information on this data sheet without prior notification to users.
Please contact a Sandvik representative for clarification on specifications and options.

ROCKTECHNOLOGY.SANDVIK

4. DL321 TOP HAMMER - LONGHOLE DRILL