Scribd
Upload
325 views

JDS2900 Function Generator Serial USB Protocol Manual

This document describes the communication protocol for the JDS6600 host computer. It consists of 3 sentences: 1) The control commands use a command line format and are sent via PC at a communication rate of 115200. 2) The machine parses the received commands for execution and returns the result to the PC. 3) The format for sent data includes a start bit, function code, data field, and terminator characters <CR><LF>.

Uploaded by

Vivi Lazuli
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
325 views

JDS2900 Function Generator Serial USB Protocol Manual

This document describes the communication protocol for the JDS6600 host computer. It consists of 3 sentences: 1) The control commands use a command line format and are sent via PC at a communication rate of 115200. 2) The machine parses the received commands for execution and returns the result to the PC. 3) The format for sent data includes a start bit, function code, data field, and terminator characters <CR><LF>.

Uploaded by

Vivi Lazuli
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

JDS6600 host computer communication protocol

◆ summarize

The control command generally adopts the command line, the


communication rate is 115200, which is sent by PC.

Out of the command, the machine parse the execution, then


returns the result to the PC machine. The following commands
are different Explain it.

The format of the sent data is as follows：

start instruction Function data


bit character Code connector field tailed

W
new line
r
See the
explana
： a 0-99 = tion
b <CR><LF>

Explain:

（1）The starting bit is the colon in the ASCII character


table (:)。

（2）The operator is four lowercase characters in the ASCII


character table, and "w" is written

The instruction is used to set various parameters, "r" is


the read instruction used to return the parameters in the
machine, "a".

The instruction is used to write the data of any wave, and


the "b" instruction is used to read the data of any wave.
（3）The function number is the numeric value in the ASCII
character table, and the difference of the value represents
the different parameter settings.

（4）According to the field: the data field is equivalent to


the operand of the command, with a number of 1 to 2048 Each
data is distinguished by "," or ".".

For example: w23=25786,0. <CR><LF> this instruction operand


is 2, the first operand is"25786", the set output frequency
is 257.86, the second bit operand is "0" set frequency The
unit of rate is Hz, in a word, this instruction sets the
frequency of channel 1 to 257.86 Hz.
（5）Terminator: each instruction ends with a return
character plus a newline.

<CR> represents the carriage return in the ASCII


character table (the sixteen is represented as 0x0D).

<LF> is a newline of the ASCII character table (the


sixteen is represented as 0x0a).

The following are the two ways to express the return


line.

◆W instruct

Channel output status settings


E.g:
PC sends: w20=1,1.<CR><lF> means that channels 1 and 2 open
the output at the same time;
PC sends: w20 = 0, 0. <CR> <lF> means that channels 1 and 2
close the output at the same time;
（1）Waveform setting

for instance：PC machine sends: w21=0.<CR><LF>

indicates that the waveform of channel 1 output

is a sine wave, and the machine returns to OK to

indicate that the setting is successful.

The PC machine sends: w21=101.<CR><LF> indicates

that the set channel output waveform is 01 of any

wave, and the machine returns to OK to indicate

that the setup is successful.


The PC machine sends w22=0.<CR><LF> to indicate

that the waveform of the channel 2 output is a

sine wave, and the machine returns to OK to

indicate that the setting is successful.

The other waveforms are set as follows：

Channel 1 Wave form Channel 2

:w21=0.<CR><LF> sine wave :w22=0.<CR><LF>

:w21=1.<CR><LF> Square wave :w22=1.<CR><LF>

:w21=2.<CR><LF> Pulse wave :w22=2.<CR><LF>

:w21=3.<CR><LF> Triangular wave The following analogy


Partial sine
:w21=4.<CR><LF> wave

:w21=5.<CR><LF> CMOS wave

:w21=6.<CR><LF> DC level
:w21=7.<CR><LF> Half wave The following analogy

:w21=8.<CR><LF> Full wave


Positive step
:w21=9.<CR><LF> wave

:w21=10.<CR><LF> Back step wave

:w21=11.<CR><LF> Noise wave

:w21=12.<CR><LF> Index rise

:w21=13.<CR><LF> Exponential drop

:w21=14.<CR><LF> For sonic

:w21=15.<CR><LF> Sieck pulse

:w21=16.<CR><LF> Lorenz pulse


When w21=101.<CR><LF> is an arbitrary
wave
01,: w21=102.<CR><LF> represents an
arbitrary wave 02,
By analogy, until the maximum of 160 is
an arbitrary wave 60。

（2）The frequency is set as follows

PC machine sends: the output frequency of

the w23=25786,1.<CR><LF> set channel 1 is

0.2586 units are KHz, and the machine

returns to OK to indicate that the setting

is successful.
PC machine sends: the output frequency of

the w24=25786,3.<CR><LF> set channel 2 is

257.86 units are mHz, and the machine

returns to OK to indicate that the setting

is successful.

Channel 1 Channel 2

:w23=25786,0.<CR><LF>csetting257.86Hz :w24=25786,0.<CR><LF>
:w23=5786,1.<CR><LF>setting0.5786KHz :w24=25786,1.<CR><LF>

:w23=25786,2.<CR><LF>setting 0.00025786MHz The following analogy

:w23=25786,3.<CR><LF>setting257.86mHz

:w23=25786,4.<CR><LF>setting 257.86uHz

（3）The range is set as follows

PC machine sends: w25=x.<CR><LF> when x=30 is set up the


channel 1 output is 0.03V, and the machine returns to OK to
indicate that the setting is successful.

PC machine sends: w26=x.<CR><LF> when x=30 is set up the


channel 2 output is 0.03V, and the machine returns to OK to
indicate that the setting is successful.

（4）The duty cycle is set as follows

PC machine sends: w29=x.<CR><LF> when x=500 is set up

the channel 1 duty ratio output is 50%, the machine

returns to OK to indicate that the setting is

successful.

PC machine sends: w29=x.<CR><LF> when x=500 is set up the

channel 2 duty ratio output is 50%, the machine returns to

OK to indicate that the setting is successful.

（5）the setting of the bias is as follows


PC machine sends: the bias output of the

w27=9999.<CR><LF> setting channel 1 is 9.99v,

The machine returns to OK to indicate that the

setup is successful.

PC machine sends: the bias output of the

w27=1000.<CR><LF> setting channel 1 is 0V,

The machine returns to OK to indicate that the

setup is successful.

PC machine sends: w27=1.<CR><LF> setting channel

1 bias output is -9.99v, and the machine returns to

OK to indicate that the setting is successful.


When setting the offset output of channel 2, just
change W27 to: W28 can be changed. For example, PC
machine sends: w28=1.<CR><LF> setting channel 2 bias
output
-9.99v, the machine returns to OK to indicate that
the setup is successful.
（6）相位设置如下
PC machine sends: w31=100.<CR><LF> indicates that
the phase output is 10 degrees, and the machine
returns
OK indicates that the setting is successful.
PC machine sends: w31=360.<CR><LF> indicates that
the phase is 0 degrees, and the machine returns to
OK
Set up a success.
(7) the following settings are set as follows

The PC machine sends: w54=x, x, x, x, x.<CR><LF> tracking


settings, the number of operands (x value) is 1, or for 0,1,
it means synchronization 0, which means asynchronism, and
synchronization is operated by channel 1. The number of
operands corresponds to w54= frequency, waveform and
amplitude.

Bias, duty ratio.

PC sends: w54=1,0,0,0,0.<CR><LF> set frequency


synchronization (waveform amplitude bias duty ratio
asynchronous), machine back to OK to indicate that the
setting is successful.

PC sends: w54=1,1,0,0,0.<CR><LF> sets frequency and


waveform synchronization (amplitude bias duty ratio
asynchronous), and the machine returns to OK to indicate
that the setting is successful.

(8) extension function (writing of instructions)

For example, the PC machine sends the numeric value of the


operands in w32=x, x, x, x.<CR><LF> (x
Value) only 1 or 0)

You might also like