Mechanical
18
FLANGES
Figure 71 Flange Adapter (ANSI Class 125/150)
The Figure 71 Flange Adapter is capable of pressures up to 300 psig
(20.7 Bar) depending on pipe size and wall thickness. It provides a
direct transition from flanged components into a grooved piping system.
GROOVED I.P.S. size flange bolt patterns conform to ANSI Class 125 and 150.
COUPLINGS
& FITTINGS The gasket seal is designed with optimum amount of rubber to provide
a dependable seal and also avoid the overfilling of the gasket pocket
which may cause assembly difficulties.
Tech Data: G150
A C
F B E D VdS LPCB
For Fire Protection Pressure Rating
and Listing / Approval information
contact Tyco Fire & Building Products.
Nominal Pipe Max.† Max. End† Nominal Dimensions Bolts** Approx.
Size OD Pressures Load A B C D* E* F Size Weight
Inches Inches psi Lbs. Inches Inches Inches Inches Inches Inches Qty Inches Lbs.
mm mm Bar kN mm mm mm mm mm mm mm Kg
5
2 2.375 300 1,329.0 6.38 4.75 0.75 2.38 3.41 7.25 4 /8 x 3 3.0
50 60.3 20.7 5.91 162.1 120.7 19.1 60.5 86.6 184.2 1.4
2 1/ 2 2.875 300 1,947.5 7.00 5.50 0.88 2.88 3.91 7.88 4 5
/8 x 3 5.0
65 73.0 20.7 8.66 178.0 140.0 22.0 73.0 99.0 200.0 2.3
5
3 3.500 300 2,886.3 7.50 6.00 0.94 3.50 4.53 9.88 4 /8 x 3 5.6
80 88.9 20.7 12.84 190.5 152.4 23.9 88.9 115.1 251.0 2.5
5
4 4.500 300 4,771.3 9.00 7.50 0.94 4.50 5.53 9.90 8 /8 x 3 7.0
100 114.3 20.7 21.22 228.6 190.5 23.9 114.3 140.5 251.5 3.2
3
5 5.563 300 7,291.7 10.00 8.50 1.00 5.56 6.72 11.38 8 /4 x 31 /2 9.2
125 141.3 20.7 32.44 254.0 215.9 25.4 141.2 170.7 289.1 4.2
3
6 6.625 300 10,341.5 11.00 9.50 1.00 6.62 7.78 11.88 8 /4 x 31 /2 10.0
150 168.3 20.7 46.02 279.4 241.3 25.4 168.1 197.6 301.8 4.5
3
8 8.625 300 17,527.9 13.50 11.75 1.13 8.62 9.94 14.36 8 /4 x 31 /2 16.6
200 219.1 20.7 77.99 342.9 298.5 28.7 218.9 252.5 365.3 7.5
7
10 10.750 300 27,228.8 16.00 14.25 1.19 10.75 12.31 16.88 12 /8 x 4 21.8
250 273.0 20.7 121.08 406.4 362.0 30.2 273.1 312.7 428.8 9.9
7
12 12.750 300 38,302.9 19.00 17.00 1.25 12.75 14.31 20.00 12 /8 x 4 24.2
300 323.9 20.7 170.44 482.6 431.8 31.8 323.9 363.9 508.0 11.0
† Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and
end loads may differ on other pipe materials and/or wall thickness. Contact Tyco Fire & Building Products for
details.
* Dimensions D and E represent minimum and maximum sealing surfaces.
** Bolts are not supplied. Bolt lengths shown are standard; it is the responsibility of the purchaser to verify correct
length for the intended application.
Note: Metal flange washer adapters are required when the Figure 71 Flange Adapter is used against surfaces such as:
• Rubber surfaces
• Adapting to AWWA cast flanges
• Rubber faced wafer valves
• Serrated flange surfaces
Figure 71 Flange Adapters are not recommended for applications which incorporate tie rods for anchoring or on a
standard fitting within 90° of each other. Contact Tyco Fire & Building Products for recommendations prior to using
with plastic pipe.
Please refer to General Notes on page 14.
www.grinnell.com 800-558-5236
Mechanical
19
FLANGES
Flange Washer Adapter
Material: Stainless Steel ASTM A666 Type 304-2B
Nominal Pipe Nominal Dimensions
Size OD A B
Inches Inches Inches Inches GROOVED
mm mm mm mm COUPLINGS
†2 2.375 3.94 2.75 & FITTINGS
50 60.3 100.0 57.2
‡21/2 2.875 4.69 2.75
65 73.0 119.1 69.9
* 3.000 4.89 2.88
76.1 124.2 73.2
‡ 3.500 5.19 3.38
88.9 131.8 85.9 A
*3 3.500 5.48 3.38
80 88.9 139.2 85.9
‡4 4.500 6.69 4.38
100 114.3 169.9 111.3
*4 4.500 6.27 4.38 B
100 114.3 159.3 111.3
‡5 5.563 7.56 5.38
125 141.3 192.0 136.7
* 5.500 7.45 5.32
139.7 189.2 135.1
* 6.500 8.47 6.32
165.1 215.1 160.5
†6 6.625 8.56 6.44
150 168.3 217.4 163.6
‡8 8.625 10.81 8.44
200 219.1 274.6 214.4
*8 8.625 10.64 8.44
200 219.1 270.3 214.4
‡10 10.750 13.19 10.50
250 273.0 335.0 266.7
*10 10.750 12.85 10.50
250 273.0 326.4 266.7
‡12 12.750 15.94 12.50
300 323.9 404.9 317.5
*12 12.750 15.01 12.50
300 323.9 381.3 317.5
* DIN
† DIN and ANSI
‡ ANSI
Note: Metal flange washer adapters are required when the Figure 71
Flange Adapter is used against surfaces such as:
• Rubber surfaces
• Adapting to AWWA cast flanges
• Rubber faced wafer valves
• Serrated flange surfaces
Please refer to General Notes on page 14.
800-558-5236 www.grinnell.com
