FORGED HOOKS

Miller’s forged hooks are produced to the following comprehensive,

international standards:

• DIN 15400- Materials, properties, capacities, stresses

• DIN 15401- Single hooks, forged
• DIN 15402- Double hooks, forged
• DIN 7540 - Eye hooks class 8 (grade 80), forged

DIN is the German Institute for Standardization (Deutsches Institut für

Normung) and has been based in Berlin since 1917. DIN has historically
developed the detailed and exacting standards used in German
engineering and is the body that represents Germany in international
standards organizations.

Forged Shank Hooks

Hooks are identified by hook number and material. Each hook number
maintains identical dimensions across a range of different materials with its
load capacity dependent on the material used. Shank hooks are forged and
heat-treated for optimal strength and toughness and are available in single
and double configurations in standard working loads to 1,100 tons. Standard
design factor is 5:1.

Hook forgings are available in three increasingly stronger carbon and alloy
steel materials:
DIN class P: Fine-grained carbon steel, St-E355/St-E420, similar to ASTMA573 Gr. 65
DIN class T: Structural low alloy steel, 34CrMo4 or 34CrNiMo6, similar to SAE 4135/4340
DIN class V: Super alloy steel, 34CrNiMo6 or 30CrNiMo8, similar to SAE 4340/4337

Forged hooks are also available to order, in bronze alloy or stainless steel for non-sparking or other special applications.
Stainless steel hooks are forged from ANSI 304 or 316L stainless steel and bronze hooks are forged from a non-sparking
aluminum-nickel bronze alloy (CuAl10Ni/C95500).

In the succeeding selection tables, working load limits (WLL) are indicated for each hook number depending on the material
selected.

Standard safety latches are included with all hook forgings. Heavy duty positive locking latches are available upon request.
See the special section of this catalog for instructions on how to order replacement latches.

Extended length shanks are available upon request.

All hooks are supplied with certifications by serial number for mechanical and chemical properties including Charpy testing,
and include 100% ultrasonic and magnetic particle non-destructive examination. Hooks include markings of fixed distances
(“y” dimension in tables) which allow confirmation that no deformation has occurred in use or during proof testing. Class V
hooks are API-2C compliant.

Machined Hooks with Nut, Suspensions and Blocks

Miller can provide forged hooks fully machined and threaded to customer requirements, matching nut included and ready for
assembly into the customer’s structure. We can also provide the complete hook suspension with trunnion and thrust
bearing, and since Miller is a block manufacturer, we can provide a complete hook block assembly for any crane type. Miller
has a full range of standard blocks for mobile cranes and produces custom blocks to order for overhead cranes.

Forged Heavy-Duty Eye Hooks

Miller’s DIN 7540 Grade 80 Eye Hook features the traditional eye-ring of circular cross section
allowing the maximum degree of motion in the connection and is available standard in working loads
up to 400 metric tons (440 short tons). These heavy duty eye hooks are forged from 34CrNiMo6V
alloy steel, include a safety latch, and can be adapted for ROV use. The standard design factor is 4:1.
See detailed eye hook tables following the shank hook tables.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 2 www.millerproducts.net - [email protected]

FORGED HOOKS- SINGLE HOOKS DIN 15401
Imperial Dimensions

Model Capacity Capacity Capacity Capacity a1 a2 a3 B b1 b2 d1 e2 e3 h1 h2 L L1 y Weight

Number Short Short Short Short Lbs.
Tons Tons Tons Tons
Carbon Alloy Super STAIN-
Class P Class T Alloy LESS
Class V STEEL
GS 1,6 3 6 7 3 2.21 1.77 2.52 3.07 1.77 1.50 1.42 5.75 4.65 2.21 1.89 10.72 8.83 10
GS 2,5 6 9 11 3 2.48 1.97 2.84 3.39 2.09 1.77 1.65 6.58 5.20 2.64 2.29 12.25 9.97 14
GS 4 9 13 18 6 2.80 2.21 3.15 3.74 2.48 2.09 1.89 7.49 5.83 3.15 2.64 13.87 11.23 19
GS 5 11 18 22 9 3.15 2.48 3.55 4.06 2.80 2.36 2.09 8.47 6.50 3.55 2.96 15.48 12.53 27
GS 6 14 22 28 11 3.55 2.80 3.98 5.52 3.15 2.64 2.36 9.46 7.29 3.94 3.35 18.32 14.97 5.12 38
GS 8 18 28 35 14 3.94 3.15 4.45 5.91 3.55 2.96 2.64 10.56 8.27 4.41 3.74 20.21 16.47 5.71 53
GS 10 22 35 44 18 4.41 3.55 5.00 6.54 3.94 3.35 2.96 11.27 8.71 4.93 4.18 21.99 17.81 6.30 75
GS 12 28 44 55 22 4.93 3.94 5.63 8.23 4.41 3.74 3.35 12.45 9.93 5.52 4.65 25.33 20.69 7.09 121
GS 16 35 55 69 28 5.52 4.41 6.30 9.38 4.93 4.18 3.74 14.07 11.03 6.30 5.20 28.64 23.44 7.88 170
GS 20 44 69 88 35 6.30 4.93 7.09 10.24 5.52 4.65 4.18 15.96 13.00 7.09 5.91 32.11 26.20 8.87 247
GS 25 55 88 110 44 7.09 5.52 7.96 11.03 6.30 5.20 4.65 17.93 14.18 7.88 6.70 35.66 28.96 10.05 353
GS 32 69 110 138 55 7.88 6.30 8.87 11.82 7.09 5.91 5.20 20.09 15.76 8.83 7.49 39.40 31.91 11.43 485
GS 40 88 138 176 69 8.83 7.09 9.93 13.32 7.88 6.70 5.91 22.34 17.61 9.85 8.35 44.01 35.66 12.61 683
GS 50 110 176 220 88 9.85 7.88 11.23 13.99 8.83 7.49 6.70 25.02 19.11 11.03 9.30 48.30 39.01 13.99 948
GS 63 138 220 276 110 11.03 8.83 12.61 16.15 9.85 8.35 7.49 27.97 21.67 12.41 10.44 54.57 44.13 15.76 1323
GS 80 176 276 353 138 12.41 9.85 14.11 18.44 11.03 9.30 8.35 31.6 23.56 13.99 11.82 61.86 50.04 17.73 1896
GS 100 220 353 441 176 13.99 11.03 15.84 20.21 12.41 10.44 9.26 35.54 27.11 15.76 13.20 68.95 55.75 19.90 2690
GS 125 276 441 551 n/a 15.76 12.41 17.73 22.46 13.99 11.82 10.44 40.19 29.55 17.73 14.78 77.42 62.65 22.46 3836
GS 160 353 551 705 n/a 17.73 13.99 19.90 25.41 15.76 13.20 11.82 45.11 32.51 19.70 16.75 87.27 70.53 25.22 5467
GS 200 441 705 882 n/a 19.70 15.76 22.26 30.38 17.73 14.78 13.20 50.24 35.46 22.06 18.72 99.41 80.69 28.37 7540
GS 250 705 882 1102 n/a 22.83 17.71 25.00 34.44 19.68 16.73 14.76 56.29 38.58 24.80 20.86 111.6 90.75 39.96 10582
•Design factor is 5:1 •For dimensional tolerances and extended shank options see page 70 •Capacities listed are per DIN
15400 drive group 1Am, which generally reflect loading conditions for mobile crane applications. The 1Am drive group can
generally be approximated to CMAA Specification No. 70, Service Class B. For application-specific information consult the
relevant standard or contact Miller for assistance.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 3 www.millerproducts.net - [email protected]

FORGED HOOKS- SINGLE HOOKS DIN 15401
Metric Dimensions

Model Capacity Capacity Capacity Capacity a1 a2 a3 B b1 b2 d1 e2 e3 h1 h2 L L1 y Weight

Number Metric Metric Metric Metric Kg
Tons Tons Tons Tons
Carbon Alloy Super STAIN-
Class P Class T Alloy LESS
Class V STEEL
GS 1,6 3 5 6.5 2.5 56 45 64 78 45 38 36 146 118 56 48 272 224 4.5
GS 2,5 5 8 10 3 63 50 72 86 53 45 42 167 132 67 58 311 253 6.3
GS 4 8 12 16 5 71 56 80 95 63 53 48 190 148 80 67 352 285 8.8
GS 5 10 16 20 8 80 63 90 103 71 60 53 215 165 90 75 393 318 12.3
GS 6 12.5 20 25 10 90 71 101 140 80 67 60 240 185 100 85 465 380 130 17.1
GS 8 16 25 32 12.5 100 80 113 150 90 75 67 268 210 112 95 513 418 145 24
GS 10 20 32 40 16 112 90 127 166 100 85 75 286 221 125 106 558 452 160 34
GS 12 25 40 50 20 125 100 143 209 112 95 85 316 252 140 118 643 525 180 55
GS 16 32 50 63 25 140 112 160 238 125 106 95 357 280 160 132 727 595 200 77
GS 20 40 63 80 32 160 125 180 260 140 118 106 405 330 180 150 815 665 225 112
GS 25 50 80 100 40 180 140 202 280 160 132 118 455 360 200 170 905 735 255 160
GS 32 63 100 125 50 200 160 225 300 180 150 132 510 400 224 190 1000 810 290 220
GS 40 80 125 160 63 224 180 252 338 200 170 150 567 447 250 212 1117 905 320 310
GS 50 100 160 200 80 250 200 285 355 224 190 170 635 485 280 236 1226 990 355 430
GS 63 125 200 250 100 280 224 320 410 250 212 190 710 550 315 265 1385 1120 400 600
GS 80 160 250 320 125 315 250 358 468 280 236 212 802 598 355 300 1570 1270 450 860
GS 100 200 320 400 160 355 280 402 513 315 265 235 902 688 400 335 1750 1415 505 1220
GS 125 250 400 500 n/a 400 315 450 570 355 300 265 1020 750 450 375 1965 1590 570 1740
GS 160 320 500 640 n/a 450 350 505 645 400 335 300 1145 825 500 425 2215 1790 640 2480
GS 200 400 640 800 n/a 500 400 565 771 450 375 335 1275 900 560 475 2523 2048 720 3420
GS 250 640 800 1000 n/a 580 450 635 875 500 425 375 1430 980 630 530 2835 2305 1015 4800
•Design factor is 5:1 •For dimensional tolerances and extended shank options see page 70 •Capacities listed are per DIN
15400 drive group 1Am, which generally reflect loading conditions for mobile crane applications. The 1Am drive group can
generally be approximated to CMAA Specification No. 70, Service Class B. For application-specific information consult the
relevant standard or contact Miller for assistance.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 4 www.millerproducts.net - [email protected]

FORGED HOOKS- DUPLEX HOOK DIN 15402
Imperial Dimensions

Model Capacity Capacity Capacity a1 a2 a3 B f1 b1 e2 d1 e3 h L L1 y Weight

Number Short Short Short Lbs.
Tons Tons Tons
Carbon Alloy Super
Class P Class T Alloy
Class V
GD 6 14 22 28 2.80 2.21 3.62 7.21 11.86 2.36 7.56 2.36 6.30 2.96 17.73 14.78 3.66 37
GD 8 18 28 35 3.15 2.48 4.06 7.76 13.28 2.64 8.59 2.64 7.17 3.35 19.70 16.35 4.12 56
GD 10 22 35 44 3.55 2.80 4.57 8.67 14.85 2.96 9.06 2.96 7.56 3.74 21.47 17.73 4.63 80
GD 12 28 44 55 3.94 3.15 5.12 10.17 16.59 3.35 9.93 3.35 8.27 4.18 24.27 20.09 5.22 111
GD 16 35 55 69 4.41 3.55 5.75 11.66 18.56 3.74 11.19 3.74 9.34 4.65 27.50 22.85 5.85 157
GD 20 44 69 88 4.93 3.94 6.42 13.08 20.92 4.18 12.53 4.18 10.44 5.20 30.81 25.61 6.52 219
GD 25 55 88 110 5.52 4.41 7.17 13.67 23.56 4.65 14.89 4.65 12.41 5.91 34.08 28.17 7.29 304
GD 32 69 110 138 6.30 4.93 8.08 15.29 26.48 5.20 15.84 5.20 13.20 6.70 37.82 31.13 8.16 434
GD 40 88 138 176 7.09 5.52 9.06 17.14 29.71 5.91 17.73 5.91 14.78 7.49 42.36 34.87 9.18 631
GD 50 110 176 220 7.88 6.30 10.24 18.16 33.17 6.70 19.86 6.70 16.55 8.35 46.37 38.02 10.44 869
GD 63 138 220 276 8.83 7.09 11.50 21.20 37.19 7.49 21.75 7.49 18.12 9.30 52.24 42.95 11.70 1206
GD 80 176 276 353 9.85 7.88 12.81 24.31 41.84 8.35 24.35 8.35 20.29 10.44 59.10 48.66 13.04 1673
GD 100 220 353 441 11.03 8.83 14.34 26.99 46.73 9.26 27.19 9.26 22.66 11.82 66.00 54.18 14.58 2337
GD 125 276 441 551 12.41 9.85 16.08 30.57 52.40 10.44 30.50 10.44 25.41 13.20 74.27 61.07 16.33 3287
GD 160 353 551 705 13.99 11.03 18.05 34.45 59.30 11.82 34.25 11.82 28.57 14.78 83.53 68.75 18.36 4663
GD 200 441 705 882 15.76 12.41 20.29 40.82 66.39 13.20 37.83 13.20 31.52 16.75 95.47 78.72 20.59 6647
GD 250 551 882 1102 17.73 13.99 22.85 47.05 74.27 14.78 41.53 14.78 34.48 18.72 107.3 88.65 23.15 9409
•Design factor is 5:1 •For dimensional tolerances and extended shank options see page 70 •Capacities listed are per DIN
15400 drive group 1Am, which generally reflect loading conditions for mobile crane applications. The 1Am drive group can
generally be approximated to CMAA Specification No. 70, Service Class B. For application-specific information consult the
relevant standard or contact Miller for assistance.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 5 www.millerproducts.net - [email protected]

FORGED HOOKS- DUPLEX HOOK DIN 15402
Metric Dimensions

Model Capacity Capacity Capacity a1 a2 a3 B f1 b1 e2 d1 e3 h L L1 y Weight

Number Metric Metric Metric Kg
Tons Tons Tons
Carbon Alloy Super
Class P Class T Alloy
Class V
GD 6 12.5 20 25 71 56 92 183 301 60 192 60 160 75 450 375 93 16.8
GD 8 16 25 32 80 63 103 197 337 67 218 67 182 85 500 415 104.5 25.3
GD 10 20 32 40 90 71 116 220 377 75 230 75 192 95 545 450 117.5 35.3
GD 12 25 40 50 100 80 130 258 421 85 252 85 210 106 616 510 132.5 50
GD 16 32 50 63 112 90 146 296 471 95 284 95 237 118 698 580 148.5 71
GD 20 40 63 80 125 100 163 332 531 106 318 106 265 132 782 650 165.5 100
GD 25 50 80 100 140 112 182 347 598 118 378 118 315 150 865 715 185 138
GD 32 63 100 125 160 125 205 388 672 132 402 132 335 170 960 790 207 197
GD 40 80 125 160 180 140 230 435 754 150 450 150 375 190 1075 885 233 286
GD 50 100 160 200 200 160 260 461 842 170 504 170 420 212 1177 965 265 394
GD 63 125 200 250 224 180 292 538 944 190 552 190 460 236 1326 1090 297 547
GD 80 160 250 320 250 200 325 617 1062 212 618 212 515 265 1500 1235 331 760
GD 100 200 320 400 280 224 364 685 1186 235 690 235 575 300 1675 1375 370 1060
GD 125 250 400 500 315 250 408 776 1330 265 774 265 645 335 1885 1550 414.5 1491
GD 160 320 500 500 355 280 458 875 1505 300 870 300 725 375 2120 1745 466 2115
GD 200 400 640 800 400 315 515 1037 1685 335 961 335 800 425 2423 1998 522.5 3015
GD 250 500 800 1000 450 355 580 1195 1885 375 1055 375 875 475 2725 2250 587.5 4268
•Design factor is 5:1 •For dimensional tolerances and extended shank options see page 70 •Capacities listed are per DIN
15400 drive group 1Am, which generally reflect loading conditions for mobile crane applications. The 1Am drive group can
generally be approximated to CMAA Specification No. 70, Service Class B. For application-specific information consult the
relevant standard or contact Miller for assistance.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 6 www.millerproducts.net - [email protected]

FORGED HOOKS- DUPLEX HOOK DIN 15402-B
Imperial Dimensions

Model Capacity Capacity Capacity a1 a2 a3 B f1 b1 d2 e2 d1 e3 h L L1 r4 y Weight

Number Short Short Short Lbs.
Tons Tons Tons
Carbon Alloy Super
Class P Class T Alloy
Class V
GDB 10 22 35 44 3.55 2.80 4.57 8.67 14.85 2.96 2.92 9.06 2.96 7.56 5.12 22.85 17.73 3.35 4.63 90
GDB 12 28 44 55 3.94 3.15 5.12 10.17 16.59 3.35 3.07 9.93 3.35 8.27 5.91 26.00 20.09 3.74 5.22 126
GDB 16 35 55 69 4.41 3.55 5.75 11.66 18.56 3.74 3.39 11.19 3.74 9.34 6.70 29.55 22.85 4.17 5.85 181
GDB 20 44 69 88 4.93 3.94 6.42 13.08 20.92 4.18 3.78 12.53 4.18 10.44 7.49 33.10 25.61 4.65 6.52 254
GDB 25 55 88 110 5.52 4.41 7.17 13.67 23.56 4.65 4.18 14.89 4.65 12.41 8.35 36.52 28.17 5.2 7.29 353
GDB 32 69 110 138 6.30 4.93 8.08 15.29 26.48 5.20 4.57 15.84 5.20 13.20 9.30 40.42 31.13 5.9 8.16 505
GDB 40 88 138 176 7.09 5.52 9.06 17.14 29.71 5.91 5.16 17.73 5.91 14.78 10.44 45.31 34.87 6.7 9.18 728
GDB 50 110 176 220 7.88 6.30 10.24 18.16 33.17 6.70 5.75 19.86 6.70 16.55 11.82 49.84 38.02 7.48 10.44 1010
GDB 63 138 220 276 8.83 7.09 11.50 21.20 37.19 7.49 6.62 21.75 7.49 18.12 13.20 56.15 42.95 8.35 11.70 1407
GDB 80 176 276 353 9.85 7.88 12.81 24.31 41.84 8.35 7.41 24.35 8.35 20.29 14.78 63.43 48.66 9.29 13.04 1967
GDB 100 220 353 441 11.03 8.83 14.34 26.99 46.73 9.26 8.20 27.19 9.26 22.66 16.75 70.92 54.18 10.4 14.58 2751
GDB 125 276 441 551 12.41 9.85 16.08 30.57 52.40 10.44 9.26 30.50 10.44 25.41 18.72 79.79 61.07 11.8 16.33 3873
GDB 160 353 551 705 13.99 11.03 18.05 34.45 59.30 11.82 10.24 34.25 11.82 28.57 20.88 89.64 68.75 13.2 18.36 5512
GDB 200 441 705 882 15.76 12.41 20.29 40.82 66.39 13.20 11.11 37.83 13.20 31.52 23.64 100.8 77.22 14.8 20.59 7848
GDB 250 551 882 1102 17.73 13.99 22.85 47.05 74.27 14.78 12.29 41.54 14.78 34.48 26.40 113.4 87.07 16.7 23.15 11096
•Design factor is 5:1 •For dimensional tolerances and extended shank length options see page 70. •Hole tolerance +2%/-0
•Capacities listed are per DIN 15400 drive group 1Am, which generally reflect loading conditions for mobile crane
applications. The 1Am drive group can generally be approximated to CMAA Specification No. 70, Service Class B. For
application-specific information consult the relevant standard or contact Miller for assistance.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 7 www.millerproducts.net - [email protected]

FORGED HOOKS- DUPLEX HOOK DIN 15402-B
Metric Dimensions

Model Capacity Capacity Capacity a1 a2 a3 B f1 b1 d2 e2 d1 e3 h L L1 r4 y Weight

Number Metric Metric Metric Kg
Tons Tons Tons
Carbon Alloy Super
Class P Class T Alloy
Class V
GDB 10 20 32 40 90 71 116 220 377 75 74 230 75 192 130 580 450 85 117.5 41
GDB 12 25 40 50 100 80 130 258 421 85 78 252 85 210 150 660 510 95 132.5 57
GDB 16 32 50 63 112 90 146 296 471 95 86 284 95 237 170 750 580 106 148.5 82
GDB 20 40 63 80 125 100 163 332 531 106 96 318 106 265 190 840 650 118 165.5 115
GDB 25 50 80 100 140 112 182 347 598 118 106 378 118 315 212 927 715 132 185 160
GDB 32 63 100 125 160 125 205 388 672 132 116 402 132 335 236 1026 790 150 207 229
GDB 40 80 125 160 180 140 230 435 754 150 131 450 150 375 265 1150 885 170 233 330
GDB 50 100 160 200 200 160 260 461 842 170 146 504 170 420 300 1265 965 190 265 458
GDB 63 125 200 250 224 180 292 538 944 190 168 552 190 460 335 1425 1090 212 297 638
GDB 80 160 250 320 250 200 325 617 1062 212 188 618 212 515 375 1610 1235 236 331 892
GDB 100 200 320 400 280 224 364 685 1186 235 208 690 235 575 425 1800 1375 265 370 1248
GDB 125 250 400 500 315 250 408 776 1330 265 235 774 265 645 475 2025 1550 300 414.5 1757
GDB 160 320 500 640 355 280 458 875 1505 300 260 875 300 725 530 2275 1745 335 466 2500
GDB 200 400 640 800 400 315 515 1037 1685 335 282 1037 335 800 600 2560 1960 375 522.5 3560
GDB 250 500 800 1000 450 355 580 1195 1885 375 312 1195 375 875 670 2880 2210 425 587.5 5030
•Design factor is 5:1 •For dimensional tolerances and extended shank length options see page 70.
•Hole tolerance is +2%/-0 •Capacities listed are per DIN 15400 drive group 1Am, which generally reflect loading conditions
for mobile crane applications. The 1Am drive group can generally be approximated to CMAA Specification No. 70, Service
Class B. For application-specific information consult the relevant standard or contact Miller for assistance.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 8 www.millerproducts.net - [email protected]

DIN SHANK HOOKS- TOLERANCES & OPTIONAL LONG
SHANKS
DIN SHANK HOOKS- TOLERANCES AND
OPTIONAL EXTENDED LENGTH SHANKS

METRIC DIMENSIONS
Single hooks per DIN 15401

Duplex hooks per DIN 15402

IMPERIAL DIMENSIONS
Single hooks per DIN 15401

Duplex hooks per DIN 15402

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 9 www.millerproducts.net - [email protected]

LATCH KITS FOR HOOKS
Miller Lifting P roduc ts
100A Stur bridge Rd.
Char lton MA 01 507 USA
800.733.7 071
[email protected]
LATCH KITS FOR STANDARDIZED EUROPEAN SHANK HOOKS
DIN 15401 SINGLE HOOKS ƒ  DIN15402 DOUBLE HOOKS Standard HD Pos Lock
 STANDARD OR HEAVY‐DUTY L OCKING TYPE
*Lo ck Pin   
*Att achme nt ha rdwar e inclu ded
Not  Show n
Hook Frame N umber Standard  Heavy‐Dut y   
Single Duple x Flapper  Positive ‐Locking
1.6 2.5 M2918 05106 M291 80710 6 How to locate  hook  frame num ber:
2.5 4 M2918 05106 M291 80720 5 See h ook m arkin gs loca ted as indic ated b elow. Hook 
4 5 M2918 05004 M291 80700 5 frame numb er is fo llowed  by a single letter P , T,V, S, or M
5 6 M2918 05005 M291 80700 7
6 8 M2918 05006 M291 80700 6
8 10 M2918 05008 M291 80700 8
10 12 M2918 05010 M291 80701 0
12 16 M2918 05012 M291 80701 2
16 20 M2918 05016 M291 80701 6
20 25 M2918 05020 M291 80702 0
25 32 M2918 05025 M291 80702 5
32 40 M2918 05032 M291 80703 2
40 50 M2918 05040 M291 80704 0
50 63 M2918 05050 M291 80705 0
63 80 M2918 05063 M291 80706 3
80 100 M2918 05080 M291 80708 0
100 125 M2918 05100 M291 80710 0
125 160 M2918 05125 M291 80712 5
160 200 M2918 05160 M291 80716 0
200 250 M2918 05200 M291 80720 0

LATCH KITS FOR  EUROPEAN EYE HOOKS
DIN 7540 Standard Flapper Latch Kits How to locate hook frame number:
*Att achme nt ha rdwar e inclu ded See h ook m arking s loca ted as indica ted b elow. Hook frame 
Hook Frame N umber Part N umbe r num ber is a two ‐digit number 34 t hroug h 42
34 M2919 91034
35 M2919 91035
36 M2919 91036
37  and 3 8 M2919 91037
39, 4 0 and  41 M2919 91039
42 M2919 91042
* Po sitive lockin g latch es by specia l orde r

LATCH KITS FOR ELD EYE HOOKS
*Att achme nt ha rdwar e inclu ded
Working Load & Material Part N umber 
3 TON CARBON M291 80300 0
5 TON CARBON / 7.5 TON ALLOY M291 80400 5
7.5 TON CARBON / 11.5 TON AL LOY  M291 80400 7
10 TON CARBON / 16 TON ALL OY  M291 80400 4
2 2 TON ALLOY M291 80400 9

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 10 www.millerproducts.net - [email protected]

FORGED EYE HOOKS- DIN 7540 GRADE 80
DIN is the German Institute for Standardization (Deutsches Institut für Normung) and has been based in Berlin
since 1917. DIN has historically developed the detailed and exacting standards used in German engineering
and is the body that represents Germany in international standards organizations.

ƒ Forged from high-strength alloy steel 34CrNiMo6V

ƒ Safe Working Loads from 40 to 400 metric tons
ƒ Design factor 4:1 to ultimate strength
ƒ Proof load is 2.5 times Safe Working Load
ƒ Includes safety latch
ƒ ROV modification (addition of pad eyes) available upon request
ƒ Higher load capacities available upon request

Metric Dimensions
Model Capacity MBL b1 d1 d1 Tolerance d2 d3 e f g h1 h2 K L X Weight Kg
Number (SWL) Metric
Metric ton
Tons
EH34 40 160 78 72 +1.9 / -3.7 44 66 388 140 109 118 103 80 19 90 31.5
EH35 50 200 89 84 +1.9 / -3.7 50 74 442 158 124 135 116 90 19 103 46
EH36 63 250 99 90 +2.3 / -4.7 56 83 494 176 138 151 130 101 19 114 63
EH37 80 320 110 102 +2.3 / -4.7 63 93 610 198 155 168 145 113 19 131 80
EH38 100 400 125 116 +/- 5.0 74 120 650 225 175 195 172 133 19 147 125
EH39 150 600 140 130 +/- 6.5 86 140 765 250 200 225 199 160 19 166 250
EH40 200 800 160 150 +/- 7.5 102 161 850 275 225 260 237 195 25 * 365
EH41 250 1000 180 170 +/- 8.5 120 195 928 310 255 290 269 210 25 * 515
EH42 300 1200 200 190 +/- 9.5 140 223 1052 350 290 330 310 240 32 * 730
EH43 400 1600 240 210 +/- 10.5 170 240 1195 400 320 380 345 270 32 * 1055

Imperial Dimensions
Model Capacity MBL b1 d1 d1 Tolerance d2 d3 e f g h1 h2 k L X Weight
Number (SWL) Short ton Lbs.
Short
Tons
EH34 44 176 3.07 2.83 +.07 / -.14 1.73 2.60 15.28 5.51 4.29 4.65 4.06 3.15 .75 3.54 69
EH35 55 220 3.50 3.31 +.07 / -.14 1.97 2.91 17.40 6.22 4.88 5.31 4.57 3.54 .75 4.06 102
EH36 69 275 3.90 3.54 +.09 / -.18 2.20 3.27 19.45 6.93 5.43 5.94 5.12 3.98 .75 4.49 139
EH37 88 353 4.33 4.02 +.09 / -.18 2.48 3.66 24.02 7.88 6.10 6.61 5.71 4.45 .75 5.16 176
EH38 110 441 4.92 4.57 +/- .19 2.91 4.72 25.59 8.86 6.89 7.68 6.77 5.24 .75 5.79 276
EH39 165 661 5.51 5.12 +/- .25 3.39 5.51 30.12 9.84 7.87 8.86 7.83 6.30 .75 6.54 551
EH40 220 882 6.30 5.91 +/- .29 4.02 6.34 33.46 10.83 8.86 10.24 9.33 7.68 .98 * 805
EH41 276 1102 7.09 6.69 +/- .33 4.72 7.68 36.54 12.20 10.04 11.42 10.59 8.27 .98 * 1135
EH42 331 1322 7.87 7.48 +/- .37 5.51 8.78 41.42 13.78 11.42 12.99 12.20 9.45 1.26 * 1609
EH43 441 1764 8.27 8.27 +/- .41 6.69 9.45 47.05 15.75 12.60 14.96 13.58 10.63 1.26 * 2326
ƒ Except where otherwise noted, dimensional tolerances for hooks through model EH37 are approximately ±5%, and increase
somewhat for hooks larger than model EH37. Contact Miller for detailed tolerance data.
ƒ Load capacities indicated are for operating temperatures between -40°C and 200°C (-40°F and 392°F). Outside this range
check with Miller for reduced capacity limits. * x dimension please inquire.

800.733.7071 - 1.508.248.3941 - Fax 1.508.248.0639 11 www.millerproducts.net - [email protected]