Duo Tandem / Quattro Tandem

EN

Installation and operating instructions

0297

9000-610-72/30
1907V007

*9000-610-72/30*
 Contents

Contents
EN

Important information Assembly

1 About this document . . . . . . . . . . . . . 3 6 Requirements . . . . . . . . . . . . . . . . . . . 15
1.1 Warnings and symbols . . . . . . . 3 6.1 Installation/setup room . . . . . . . 15
1.2 Copyright information . . . . . . . . 3 6.2 Setup . . . . . . . . . . . . . . . . . . . . 15
2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . 4 6.3 Information about electrical con-
nections . . . . . . . . . . . . . . . . . . 15
2.1 Intended purpose . . . . . . . . . . . 4
2.2 Intended use . . . . . . . . . . . . . . . 4 7 Transport . . . . . . . . . . . . . . . . . . . . . . . 16
2.3 Improper use . . . . . . . . . . . . . . . 4 8 Installation . . . . . . . . . . . . . . . . . . . . . . 16
2.4 General safety information . . . . . 5 8.1 Remove the transport locks . . . 16
2.5 Specialist personnel . . . . . . . . . 5 8.2 Installing the compressor unit . . 16
2.6 Electrical safety . . . . . . . . . . . . . 5 8.3 Establishing the compressed air
2.7 Notification requirement of seri- connection . . . . . . . . . . . . . . . . 18
ous incidents . . . . . . . . . . . . . . . 5 8.4 Pressure reducer . . . . . . . . . . . 18
2.8 Only use original parts . . . . . . . . 5 8.5 Place a collector tray underneath . 19
2.9 Transport . . . . . . . . . . . . . . . . . . 5 8.6 Network connection . . . . . . . . . 19
2.10 Disposal . . . . . . . . . . . . . . . . . . 6 8.7 Electrical connections . . . . . . . . 20
8.8 Two devices in a single com-
pressed air network . . . . . . . . . . 20
9 Commissioning . . . . . . . . . . . . . . . . . . 22
Product description 9.1 Checking the switch-on/cut-off
3 Overview . . . . . . . . . . . . . . . . . . . . . . . 7 pressure . . . . . . . . . . . . . . . . . . 22
3.1 Scope of delivery . . . . . . . . . . . . 7 9.2 Checking the safety valve . . . . . 22
3.2 Optional items . . . . . . . . . . . . . . 7 9.3 Draining the condensation water . 23
3.3 Wear parts and replacement 9.4 Adjusting the rate of flow at the
parts . . . . . . . . . . . . . . . . . . . . . 7 pressure reducer . . . . . . . . . . . . 23
4 Technical data . . . . . . . . . . . . . . . . . . . 8 9.5 Monitoring the unit via the net-
4.1 Duo Tandem . . . . . . . . . . . . . . . 8 work . . . . . . . . . . . . . . . . . . . . . 23
4.2 Quattro Tandem . . . . . . . . . . . . 10 10 Adjustment options . . . . . . . . . . . . . . 24
4.3 Distance between rubber feet . . 12 10.1 Adjustment of the switch-on/cut
4.4 Type plate . . . . . . . . . . . . . . . . . 12 off pressure . . . . . . . . . . . . . . . . 24
4.5 Evaluation of conformity . . . . . . 12 11 Controller . . . . . . . . . . . . . . . . . . . . . . . 26
5 Operation . . . . . . . . . . . . . . . . . . . . . . 13
5.1 Duo Tandem / Quattro Tandem . 13
5.2 Start-up behaviour . . . . . . . . . . 13
5.3 Operating panel . . . . . . . . . . . . . 14 Usage
12 Operation . . . . . . . . . . . . . . . . . . . . . . 28
12.1 Operating panel . . . . . . . . . . . . . 28
12.2 Switching the unit on/off . . . . . . 29
12.3 Normal operation . . . . . . . . . . . . 29
12.4 Standby mode . . . . . . . . . . . . . 29

9000-610-72/30 1907V007 1
 Contents

12.5 Auxiliary operation . . . . . . . . . . . 29

12.6 Set-up mode . . . . . . . . . . . . . . . 29
12.7 Fault . . . . . . . . . . . . . . . . . . . . . 29
12.8 Emergency mode . . . . . . . . . . . 29
EN 13 Maintenance . . . . . . . . . . . . . . . . . . . . 31
13.1 Maintenance schedule . . . . . . . . 31
13.2 Changing the filter . . . . . . . . . . . 32
14 Taking out of use . . . . . . . . . . . . . . . . 33
14.1 Taking the unit out of use . . . . . 33
14.2 Storage of the unit . . . . . . . . . . 34

Troubleshooting
15 Tips for operators and service techni-
cians . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Appendix
16 Handover protocol . . . . . . . . . . . . . . . 38

2 9000-610-72/30 1907V007
 Important information

The signal word differentiates between four levels

Important information of danger:
– DANGER
Immediate danger of severe injury or death
1 About this document – WARNING
EN
These installation and operating instructions rep- Possible danger of severe injury or death
resent part of the unit. – CAUTION
If the instructions and information in these Risk of minor injuries
installation and operating instructions are – NOTICE
not followed, Dürr Dental will not be able Risk of extensive material/property damage
to offer any warranty or assume any liabil-
Other symbols
ity for the safe operation and the safe
functioning of the unit. These symbols are used in the document and on
or in the unit:
The German version of the installation and oper-
Note, e.g. specific instructions regarding
ating instructions is the original manual. All other
efficient and cost-effective use of the unit.
languages are translation of the original manual.
These installation and operating instructions
apply to: Observe the operating instructions.
Duo Tandem
Order number: 4152-54; 4252-54
Quattro Tandem Disconnect all power from the unit.
Order number: 4642-54; 4682-54; 4682100001
Refer to the accompanying electronic
1.1 Warnings and symbols
documents.
Warnings
The warnings in this document are intended to Air
draw your attention to possible injury to persons
or damage to machinery.
The following warning symbols are used: Dispose of correctly in accordance with
EU Directive 2012/19/EU (WEEE).
General warning symbol
CE labelling with the number of the noti-
fied body
Warning – dangerous high voltage
Order number

Warning – hot surfaces

Serial number

Warning - automatic start-up of the unit Medical device

The warnings are structured as follows: Health Industry Bar Code (HIBC)

SIGNAL WORD
Manufacturer
Description of the type and source of
danger
Here you will find the possible conse- 1.2 Copyright information
quences of ignoring the warning All circuits, processes, names, software pro-
❯ Follow these measures to avoid the grams and units mentioned in this document are
danger. protected by copyright.

9000-610-72/30 1907V007 3
 Important information

The Installation and Operating Instructions must 2 Safety

not be copied or reprinted, neither in full nor in
part, without written authorisation from Dürr Dürr Dental has designed and constructed this
Dental. unit so that when used properly and for the
intended purpose it does not pose any danger to
EN people or property.
Despite this, the following residual risks can
remain:
– Personal injury due to incorrect use/misuse
– Personal injury due to mechanical effects
– Personal injury due to electric shock
– Personal injury due to radiation
– Personal injury due to fire
– Personal injury due to thermal effects on skin
– Personal injury due to lack of hygiene, e.g.
infection

WARNING
The development of emphysema
Soft tissue can be damaged as a result
of careless handling.
❯ Do not dwell in the area being treated
for any longer than is necessary.

2.1 Intended purpose

The compressor is designed to supply com-
pressed air for dental applications.

2.2 Intended use

The air supplied by the compressor is suitable for
driving dental tools.
The compressed air generated by the compres-
sor is delivered to the pipeline system of the
surgery. The entire compressed air system must
be designed in such a way that the quality of the
compressed air generated by the compressor is
not impaired.
With this prerequisite, the air provided by the
compressor is also suitable for blow-drying tooth
preparations.

2.3 Improper use

Any use of this appliance / these appliances
above and beyond that described in the Installa-
tion and Operating Instructions is deemed to be
incorrect usage. The manufacturer cannot be
held liable for any damage resulting from incor-
rect usage. The operator will be held liable and
bears all risks.

4 9000-610-72/30 1907V007
 Important information

2.6 Electrical safety

WARNING
❯ Observe and comply with all the relevant elec-
Risk of explosion due to ignition of trical safety regulations when working on the
combustible materials unit.
❯ Do not operate the unit in any rooms in ❯ Replace any damaged cables or plugs immedi- EN
which inflammable mixtures may be ately.
present, e.g. in operating theatres.
❯ The unit is not suitable for providing an air sup- 2.7 Notification requirement of
ply to respirators. serious incidents
❯ This unit is not suitable for drawing up fluids or The user / patient is required to report to the
for compressing aggressive gases or poten- manufacturer and the competent authority of the
tially explosive gases. Member State, in which the user and/or patient is
established, any serious incident that has
2.4 General safety information occurred in relation to the device.
❯ Always comply with the specifications of all
guidelines, laws, and other rules and regula- 2.8 Only use original parts
tions applicable at the site of operation for the ❯ Only use Dürr Dental parts or accessories and
operation of this unit. special accessories specifically approved by
❯ Check the function and condition of the unit Dürr Dental.
prior to every use. ❯ Only use only original wear parts and replace-
❯ Do not convert or modify the unit. ment parts.
❯ Comply with the specifications of the Installa- Dürr Dental accepts no liability for dam-
tion and Operating Instructions. ages or injury resulting from the use of
❯ The Installation and Operating Instructions non-approved accessories or optional
must be accessible to all operators of the unit accessories, or from the use of non-origi-
at all times. nal wear parts or replacement parts.
The use of non-approved accessories,
2.5 Specialist personnel optional accessories or non-genuine wear
Operation parts / replacement parts (e.g. mains
cable) can have a negative effect in terms
Unit operating personnel must ensure safe and
of electrical safety and EMC.
correct handling based on their training and
knowledge.
❯ Instruct or have every user instructed in han- 2.9 Transport
dling the unit. The original packaging provides optimum protec-
The following groups are not permitted to tion for the unit during transport.
operate or use a commercially operated unit: If required, original packaging for the unit can be
– People without the necessary experience and ordered from Dürr Dental.
knowledge Dürr Dental will not accept any responsi-
– People with reduced physical, sensory or men- bility or liability for damage occurring dur-
tal capabilities ing transport due to the use of incorrect
– Children packaging, even where the unit is still
under guarantee.
Installation and repairs
❯ Installation, readjustments, alterations, ❯ Only transport the unit in its original packaging.
upgrades and repairs must be carried out by ❯ Keep the packing materials out of the reach of
Dürr Dental or by qualified personnel specifi- children.
cally approved and authorized by Dürr Dental.

9000-610-72/30 1907V007 5
 Important information

2.10 Disposal
The unit must be disposed of properly.
Within the European Union, the unit must
be disposed of in accordance with EU
EN Directive 2012/19/EU (WEEE).
❯ If you have any questions about the correct
disposal of parts, please contact your dental
trade supplier.
An overview of the waste keys for Dürr
Dental products can be found in the
download area at www.duerrdental.com
(document no. P007100155).

6 9000-610-72/30 1907V007
 Product description

Sterile filter . . . . . . . . . . . . . . . . . . 1640-981-00

Product description Network cable 3 m . . . . . . . . . . . 9000-119-071

3.3 Wear parts and replacement

3 Overview parts EN
3.1 Scope of delivery The following working parts must be replaced at
The following items are included in the scope of regular intervals (refer also to "Maintenance");
delivery (possible variations due to country-spe- these articles do not bear the CE mark:
cific requirements and/or import regulations): Air intake filter . . . . . . . . . . . . . . . . 0832-982-00
Fine filter . . . . . . . . . . . . . . . . . . . . 1610-121-00
Duo Tandem Sterile filter . . . . . . . . . . . . . . . . . . 1640-981-00
Duo Tandem 400 V, 3~, with 1 com- Sintered filter . . . . . . . . . . . . . . . . . 1650-101-00
pressor unit and membrane drying
unit * . . . . . . . . . . . . . . . . . . . . . . . . . . 4152-54 Any repairs exceeding routine mainte-
Duo Tandem 400 V, 3~, with 2 com- nance may only be carried out by quali-
pressor units and membrane drying fied personnel or our service.
unit * . . . . . . . . . . . . . . . . . . . . . . . . . . 4252-54 Information about replacement parts is
– Connection parts available from the portal for authorised
– Collector tray specialist dealers at:
– Network cable, 3 m www.duerrdental.net.
– Installation and operating instructions
If the mains cable of this unit is damaged
– Appliance log book it must only be replaced by an original
mains cable from the manufacturer.
* with sterile filter
Quattro Tandem
Quattro Tandem 400 V, 3~, with 1
compressor unit and membrane dry-
ing unit * . . . . . . . . . . . . . . . . . . . . . . . 4642-54
Quattro Tandem 400 V, 3~, with 2
compressor units and membrane dry-
ing unit * . . . . . . . . . . . . . . . . . . . . . . . 4682-54
Quattro Tandem 400 V, 3~, with 2
compressor units and membrane
drying unit * . . . . . . . . . . . . . . . . . 4682100001
– Pressure tank
– Compressor unit
– Connection parts
– Vibration dampers
– Collector tray
– Network cable, 3 m
– Installation and operating instructions
– Appliance log book

* with sterile filter

3.2 Optional items

The following items can optionally be used with
the unit; these items do not bear the CE mark:
Pressure reducer . . . . . . . . . . . . . . 6040-992-00

9000-610-72/30 1907V007 7
 Product description

4 Technical data
4.1 Duo Tandem
EN Electrical data 4152-54 4252-54
Rated voltage V 400 400
Mains frequency Hz 50 60 50 60
Nominal current at 8 bar (0.8 MPa) A 3.1 2.5 6.2 5.0
Speed rpm 1410 1690 1410 1690
Type of protection IP 21 IP 21
Mains fuses * A 10 10

* Circuit breaker fuse characteristics B, C or D in acc. with EN 60898-1

General technical data

Pressure tank volume l 50 50
Suction power, approx. l/min 210 255 420 505
Delivery at 5 bar (0.5 MPa) * l/min 115 130 225 260
Pressure build-up phase 0 - 7.5 bar (0 -
0.75 MPa) c. s 205 180 100 90
Duty cycle % 100 100
Start-up pressure bar (MPa) 5.5 (0.55) 5.5 (0.55)
Cut-off pressure bar (MPa) 7.5 (0.75) 7.5 (0.75)
Cut-off pressure, max. adjustable bar (MPa) 9.0 (0.9) 9.0 (0.9)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1) 10 (1)
Pressure dew point at 7 bar (0.7 MPa) ** °C £ +5 £ +5
Dimensions (H x W x D) *** cm 76 x 75 x 52 76 x 79 x 52
Weight kg 70 100
Noise level **** dB(A) 66 68 69 72

* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
** Value determined at an ambient temperature of +40 °C
*** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744

Filter mesh size

Compressor air intake filter µm 3
Fine filter for membrane drying unit µm 3
Sterile filter for membrane drying unit µm 0.01
Sintered filter for membrane drying unit µm 35

Network connection
LAN technology Ethernet

8 9000-610-72/30 1907V007
 Product description

Network connection
Standard IEEE 802.3u
Data rate Mbit/s 100
Connector RJ45 EN
Type of connection Auto MDI-X
Cable type ³ CAT5

Ambient conditions during storage and transport

Temperature °C -10 to +55
Relative humidity % max. 95

Ambient conditions during operation

Temperature °C +10 to +40
Ideal temperature °C +10 to +25
Relative humidity % max. 95

Classification
Medical devices class IIa

9000-610-72/30 1907V007 9
 Product description

4.2 Quattro Tandem

Electrical data 4642-54 4682-54
4682100001
Rated voltage V 400 400
EN
Mains frequency Hz 50 60 50 60
Nominal current at 8 bar (0.8 MPa) A 4.4 4.8 8.8 9.6
Speed rpm 1440 1700 1440 1700
Type of protection IP 21 IP 21
Mains fuses * A 16 16
Max. permissible mains impedance in
accordance with EN 61000‑3‑11 ** W £ 0.18 £ 0.18

* Circuit breaker fuse characteristics B, C or D in acc. with EN 60898-1

** Mains impedance at 6 switching cycles per hour. If the number of switching cycles per hour is
higher a lower mains impedance is required.

General technical data

Pressure tank volume l 90 90
Suction power, approx. l/min 420 505 845 1010
Delivery at 5 bar (0.5 MPa) * l/min 220 255 440 515
Pressure build-up phase 0 - 7.5 bar (0 -
0.75 MPa) c. s 180 160 90 80
Duty cycle % 100 100
Start-up pressure bar (MPa) 5.5 (0.55) 5.5 (0.55)
Cut-off pressure bar (MPa) 7.5 (0.75) 7.5 (0.75)
Cut-off pressure, max. adjustable bar (MPa) 9.0 (0.9) 9.0 (0.9)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1) 10 (1)
Pressure dew point at 7 bar (0.7 MPa) ** °C £ +5 £ +5
Dimensions (H x W x D) *** cm 82 x 102 x 62 82 x 102 x 62
Weight kg 120 170
Noise level **** dB(A) 69 70 72 73

* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
* Value determined at an ambient temperature of +40 °C
** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744

Filter mesh size

Compressor air intake filter µm 3
Fine filter for membrane drying unit µm 3
Sterile filter for membrane drying unit µm 0.01
Sintered filter for membrane drying unit µm 35

10 9000-610-72/30 1907V007
 Product description

Network connection
LAN technology Ethernet
Standard IEEE 802.3u
Data rate Mbit/s 100 EN
Connector RJ45
Type of connection Auto MDI-X
Cable type ³ CAT5

Ambient conditions during storage and transport

Temperature °C -10 to +55
Relative humidity % max. 95

Ambient conditions during operation

Temperature °C +10 to +40
Ideal temperature °C +10 to +25
Relative humidity % max. 95

Classification
Medical devices class IIa

9000-610-72/30 1907V007 11
 Product description

Compressor unit
4.3 Distance between rubber feet The type plate of the compressor unit is located
Distances between the rubber feet for different on the crankcase below the cylinder.
pressure vessel volumes:
b
EN

1
1 Compressor unit type plate

Membrane drying unit

a (cm) b (cm)
The type plate of the membrane drying unit is
20 l 23 27 located on the side of the membrane drying unit.
50 l 32.5 45
90 l 32.5 59

4.4 Type plate

Complete system
The type plate for the complete system is located 1
on the pressure tank.

1 1 Membrane drying unit type plate

4.5 Evaluation of conformity

This device has been subjected to conformity
acceptance testing in accordance with the cur-
rent relevant European Union guidelines. This
equipment conforms to all relevant requirements.

1 Type plate for the complete system

12 9000-610-72/30 1907V007
 Product description

5 Operation The compressor unit draws in atmospheric air

and compresses it without oil. It then transports
5.1 Duo Tandem / Quattro the oil-free compressed air to the membrane dry-
ing unit. The cooler and the membrane dryer
Tandem extract moisture from the compressed air. The
13 oil-free, hygienic and dry air is stored in the pres-
EN
1 sure tank ready for use in connected devices.
All of the measurement data for the unit comes
together in the control (e.g. pressure in the pres-
sure tank, temperature of the motor windings),
where it is then evaluated. Likewise, various set-
2 12
tings (e.g. switch-on/cut-off pressure) can be
adjusted, or the unit can be connected via the
network to monitoring software.
3
11
10 5.2 Start-up behaviour
9 On compressors with an electronic controller, the
4 compressor units are switched on with a time
delay. The time delay depends on the operating
mode selected on the controller.
Operating mode:
– Eco: 180 s
– Balanced: 60 s
– Boost: 10 s
Alternating control:
The compressor unit with the shortest operating
time since the compressor was connected to
5 voltage is started. This distributes the operating
6
7 time more or less uniformly between the com-
8 pressor units. If the compressor is disconnected
from the voltage and is then reconnected to the
power supply, compressor unit 1 will start first
again.
1 Air intake filter
2 Compressor unit
3 Fine filter or sterile filter, membrane drying
unit
4 Collector tray
5 Safety valve
6 Pressure gauge/display
7 Compressed air connection (quick release
coupling)
8 Condensate drain valve
9 Pressure tank
10 Automatic/manual condensate drain valve,
membrane drying unit
11 Sinter filter for membrane drying unit
12 Intake connector
13 Controller

9000-610-72/30 1907V007 13
 Product description

5.3 Operating panel

1 2 3 4 5 6

EN

1 Fault button with orange LED

2 Filter change button with orange LED
3 Service key with blue LED
4 Standby button with blue LED
5 Pressure range display/adjustment
6 Pressure dew point display
Different messages and the status of the unit are
displayed on the operating panel. In addition, dif-
ferent functions can be started via the buttons.

14 9000-610-72/30 1907V007
 Assembly

Assembly
≥ 40 °C
6 Requirements
EN
The unit must not be set up or operated
within the vicinity of the patients (within a
radius of 1.5 m).
The unit can be installed either at the same level
as the surgery room or on a floor below (e.g. cel-
lar).
Due of the amount of noise generated, we rec-
ommend that the unit is installed in an adjoining
room.
The pipes provided on-site must at least meet
the country-specific requirements for drinking
water. 6.2 Setup
Further information can be found in our The following conditions must be taken into
separate planning information leaflet for account for installation:
compressed air. The air is filtered when it is sucked in. This
does not alter the composition of the air.
6.1 Installation/setup room For this reason it is important to keep the
The room chosen for set up must fulfil the follow- sucked-in air free of harmful substances
ing requirements: (e.g. do not suck in exhaust gases or
– Closed, dry, well-ventilated room contaminated exhaust air).
– Should not be a room made for another pur- – Clean, level and sufficiently stable subsurface
pose (e. g. boiler room or wet cell) (note the weight of the unit).
– If the unit is installed in a machine room, e.g. in – Type plate easy to read.
an adjoining room or cellar, the requirements – Unit easy to access for operation and mainte-
set out in ISO‑TS 22595 must be complied nance.
with. – Easy-to-access power outlet to which the unit
is connected.
ACHTUNG
– Maintain sufficient distance to the wall (at least
Risk of overheating due to insufficient 20 cm).
ventilation
– The compressed air pipe should be routed as
The units generates heat. Possibility of closely as possible to the place of installation
heat damage and/or reduced service life (note the length of the hose supplied).
of the unit.
❯ Do not cover the unit. 6.3 Information about electrical
❯ Install a fan for auxiliary ventilation in connections
rooms where ambient temperatures ❯ Ensure that the electrical connections to the
exceed ³40 °C while the unit is in mains power supply are established in accor-
operation. dance with current valid national and local reg-
ulations and standards governing the installa-
tion of low voltage units in medical facilities.
❯ Observe the current consumption of the
devices that are to be connected.

9000-610-72/30 1907V007 15
 Assembly

7 Transport 8 Installation
WARNING 8.1 Remove the transport locks
Risk of explosion of the pressure tank The transport locks only need to be
EN and pressure hoses removed on the Duo Tandem, as the
❯ The pressure tank and the pressure compressor units are delivered separately
hoses must be vented before they are for the Quattro Tandem.
stored or transported. For safe transport, the appliance is securely pro-
❯ Protect the unit against moisture, dirt and tected with two foam blocks and a retaining
extreme temperatures during transport ("4 strap.
Technical data"). ❯ Cut and remove the retaining strap.
❯ Always make sure that the condensate collec- ❯ Remove the foam blocks.
tor chamber is empty before transporting the ❯ Check the unit for transport damage.
unit ("14 Taking out of use").
❯ Always transport the unit in an upright position. 8.2 Installing the compressor unit
❯ Only transport the unit using the transport han- The compressor units only need to be
dles provided. installed on the Quattro Tandem.
❯ Check the unit for transport damage.
❯ Screw the vibration reducers with short
threaded bolts into the retaining plate.

16 9000-610-72/30 1907V007
 Assembly

❯ Place the compressor units on the vibration ❯ Connect the compressor unit with the mem-
reducers with the motor terminal box facing brane drying unit via the pressure hose.
towards the control.

EN

Warning – risk of dangerous electric volt-

ages
❯ The mains plug must not be plugged in. If it is
plugged in, unplug it.
❯ Unscrew the fastening screws of the cover for
the control.

❯ Attach the compressor unit with the lock wash-

ers and nuts.

4x

NOTICE
The operating panel cable is very
short and can damage the PCB when
the cover is removed.
❯ Carefully remove the cover of the con-
trol.
❯ Unplug the operating panel cable.

9000-610-72/30 1907V007 17
 Assembly

When routeing the cables, maintain the 8.3 Establishing the compressed
correct gaps between control cables and air connection
supply cables.
The supplied flexible pressure hose
❯ Guide the cables of the compressor units between the pipe system and the com-
EN through the strain relief and fasten. pressor prevents vibrations from being
transmitted and thus reduces noise. This
ensures safe and reliable operation.
❯ Connect the premounted connecting sleeve on
the pressure hose to the quick release coupling
of the distributor block.

❯ Plug the connector of the temperature sensor

and power supply of the compressor unit into
the sockets provided.
Connect the network cable for the monitoring
software
A network connection is only required
when using monitoring software.

❯ Connect the network cable to the network

socket.
Installation of the cover
❯ Connect the operating panel cable again. ❯ Measure the required length of pressure hose
and shorten the pressure hose if necessary.
❯ Attach the cover of the control again and fas-
ten it with the screw. ❯ Slide the second hose nozzle in place and
secure with a hose clip.
DANGER ❯ Connect the connecting sleeve on the pressure
hose to the piping system.
Risk of electric shock due to defective
mains cable
8.4 Pressure reducer
❯ Mains cables must not be allowed to
come into contact with any hot sur- ❯ Insert the pressure reducer into the quick
faces on the unit. release coupling.
❯ Insert the pressure hose into the quick release
❯ Attach the cables using the cable clips. coupling on the pressure reducer.

18 9000-610-72/30 1907V007
 Assembly

❯ Place a collector tray under every membrane

drying unit.

EN

8.6 Network connection

8.5 Place a collector tray under- Purpose of the network connection
neath The network connection is used to exchange
During operation, condensed water is continu- information or control signals between the unit
ously collected in the membrane-drying unit and and a software installed on a computer, in order
drained off automatically. In order to prevent to, e. g.:
water damage due to drained condensation – Display parameters
water, it is collected in the collector tray. – Select operating modes
As an option, the condensed water can – Indicate messages and error situations
be removed via a hose that is connected – Change unit settings
to the waste water system. – Activate test functions
– Transmit data for archiving
– Provide documents concerning the units
During initial installation, we recommend a
router or server with DHCP so that the
unit is detected in the network.
❯ Plug the network cable into the control and into
a network socket.

9000-610-72/30 1907V007 19
 Assembly

❯ Connect to the computer network with the net- ❯ Connect the mains plug to an earthed power
work cable. outlet.
The unit will start immediately when the mains
DHCP plug is connected.
❯ Check whether the power outlet is switched via
EN the surgery main power switch.
This ensures that the unit starts up automati-
cally after the surgery main switch is routinely
switched off and back on again.

8.8 Two devices in a single com-

pressed air network
With the compressor it is possible for two units to
be connected to a single compressed air net-
work. To do this,
– the pressure vessels need to be connected to
each other;
compressor – the controllers of the compressors need to be
connected to each other;
– the controllers need to be set up accordingly.
8.7 Electrical connections
Connecting pressure vessels
Safety when making electrical connections
If two devices are connected to a single com-
The unit has no main power switch. For pressed air network, pressure equalisation must
this reason it is important that the unit is take place between the pressure vessels. To do
be set up in such a way that the plug can this, the pressure vessels need to be connected
be easily accessed and unplugged if to each other.
required. So that the pressure can be equalised, no
❯ The unit must only be connected to a correctly non-return valves must be installed
installed power outlet. between the pressure vessels.
❯ Make sure that none of the electrical cables
leading to the unit are under any mechanical
MAIN AUX
tension.
❯ Before initial start-up check that the mains sup-
ply voltage and the voltage stated on the type
plate match (see also "4. Technical data").
Establishing the electrical connections

DANGER
Risk of electric shock due to defective
mains cable
❯ Mains cables must not be allowed to 1 Main device (MAIN)
come into contact with any hot sur- 2 Auxiliary device (AUX)
faces on the unit.
M/S AUX for main device / auxiliary device
The two electronic controllers of the compressors
are connected to each other via a network cable.
When routing the cables, maintain the
correct gaps between control cables and
supply cables.

20 9000-610-72/30 1907V007
 Assembly

❯ Connect the network cable to the network The device is operated via the operating panel of
socket X10. the main control. The auxiliary control is inactive
❯ Guide the cable through the cable holder and (standby button flashing) and cannot be oper-
the tension relief and secure it. ated.
❯ Working in the controller of the compressor to EN
be operated as the primary compressor, check
whether the switch S1 is in the right-hand posi-
tion. If it is not, move it to the right (main con-
trol).

S1

X10

Fig. 1: Main controller

❯ Working in controller of the compressor to be

operated as the secondary compressor, move
the switch S1 to the left-hand position (auxiliary
control).

S1

X10

Fig. 2: Auxiliary controller

9000-610-72/30 1907V007 21
 Assembly

9 Commissioning ❯ Fill the pressure tank to the cut-off pressure.

In many countries technical medical prod- WARNING

ucts and electrical devices are subject to Risk of damage to the safety valve
regular checks at set intervals. The owner
EN must be instructed accordingly. Risk of explosion of the pressure tank
and pressure hoses due to a defective
❯ Carry out an electrical safety check in accor- safety valve
dance with applicable local regulations (e.g. the
❯ Do not use the safety valve to vent the
German Ordinance on the Installation, Opera-
pressure tank.
tion and Use of Medical Devices / Medizinpro-
dukte-Betreiberverordnung) and record the ❯ When the cut off pressure is reached, turn the
results as appropriate, e.g. in the technical log screw of the safety valve several turns anti-
book. clockwise until the valve begins to blow. Only
❯ Carry out and document the instruction and allow the safety valve to blow for a short
handover for the unit. period.
A sample handover report is included in
the attachment.

9.1 Checking the switch-on/cut-

off pressure
The switch-on/cut-off pressure is preset at the
factory. Check the adjustment during first start-
up.
When the mains plug is connected the compres-
sor will start after a short delay.
❯ Read off the cut-off pressure from the pressure
gauge.
❯ Drain the air from the pressure tank (e.g. via
the condensate drain valve) until the unit starts
and then close it again.
❯ Read off the pressure when the unit starts up.
If the readings deviate from the values preset at
❯ Turn the screw clockwise as far as it will go.
the factory, adjust the values to the factory set-
The valve must now be closed again.
tings. If other pressure values are required, take
Checking the safety valve – alternative
care to observe the maximum pressure differ-
method:
ence.
With this function the safety valve will
9.2 Checking the safety valve open suddenly and emit a very loud blow-
The safety valve must be checked to establish off noise
that it is working correctly when the unit is ❯ Press and hold the service key until the
started up for the first time. safety valve triggers.
At the factory, the safety valve is set to The compressor units keep running as long
10 bar (1 hPa), checked and stamped. as the button is pressed. The defined cut off
pressure is not taken into account.

DANGER
Risk of explosion of the pressure tank
and pressure hoses
❯ Do not change the safety valve set-
tings.

22 9000-610-72/30 1907V007
 Assembly

9.3 Draining the condensation

water
During transport, condensation water can accu-
mulate in the pressure tank due to changes in
temperature. EN
This also applies to compressors with a mem-
brane drying unit.
❯ At maximum tank pressure, slowly open the 2.
condensate drain valve.
+
1.
- 3.

9.5 Monitoring the unit via the

network
The following requirements must be met in order
to monitor the unit on the computer:
– Unit connected to the network
– Current monitoring software installed on the
computer
Combining devices safely
– The overall safety of the unit and its main per-
formance features are independent of the net-
work. The device is designed for operation
independent of a network. However, some of
the functions are not available in this case.
– Incorrect manual configuration can lead to sig-
nificant network problems. The expert knowl-
❯ Close the condensate drain valve as soon as edge of a network administrator is required for
all of the condensation water has been blown configuration.
out. – The data connection utilises part of the band-
width of the network. Interactions with other
9.4 Adjusting the rate of flow at medical devices cannot be completely ruled
out. Apply the IEC 80001‑1 standard for risk
the pressure reducer
assessment.
The pressure reducer regulates the rate of flow in
– The device is not suitable for direct connection
the system and adjusts it to the required operat-
to the public internet.
ing pressure. In order to adjust the rate of flow air
needs to be extracted via a consumer. Network configuration
❯ Activate the air consumer unit. Various options are available for network configu-
❯ Lift the rotary knob at the pressure reducer. ration:
❯ Adjust the rate of flow via the rotary knob. ü Automatic configuration via DHCP (recom-
Turn the knob in the "+" direction to increase mended).
the rate of flow. ü Automatic configuration via Auto-IP for direct
Turn the knob in the "-" direction to reduce the connection of unit and computer.
rate of flow. ü Manual configuration.
❯ Press in the rotary knob until it engages and ❯ Configure the network settings of the unit using
cannot be adjusted. the software or, if available, the touch screen.

9000-610-72/30 1907V007 23
 Assembly

❯ Check the firewall and release the ports, if 10 Adjustment options

applicable.
Network protocols and ports 10.1 Adjustment of the switch-
Port Purpose Service on/cut off pressure
EN
45123 UDP, Unit recognition and WARNUNG
45124 UDP configuration
Risk of explosion of the pressure ves-
1900 UDP Service detection SSDP / sel
UPnP
The pressure vessels used in the com-
502 TCP Unit data pressors are designed to withstand
5141) UDP Event protocol data Syslog continuous pressure changes of 2 bar
and can be used continuously under
22 TCP Diagnosis Telnet,
these pressure changes.
SSH
❯ For load changes > 2 bar (max. per-
123 UDP Time NTP missible: 3 bar), comply with the maxi-
mum load change cycles specified in
1) The port can vary depending on the config- the operating instructions of the pres-
uration. sure vessel.
The pressure adjustment is performed in standby
mode.
❯ Standby button: press for at least 2 sec-
onds.
❯ Service key: press for at least 2 seconds.
The blue LEDs in the operating panel flash.
They are touch-sensitive and can be adjusted
accordingly.

7
6 8

5 9
bar
The blue LEDs in the operating panel flash. They
are touch-sensitive and can be adjusted accord-
ingly.
The pressure adjustment is performed in
0.5 bar increments by touching the LED.

The blue LEDs in the operating panel flash. They

are touch-sensitive and can be adjusted accord-
ingly.
❯ Touch the first flashing LED with your finger
and swipe to the required switch on pressure.
❯ Touch the last flashing LED with your finger and
swipe to the required cut off pressure.

24 9000-610-72/30 1907V007
 Assembly

❯ Use the service key to confirm.

If no touch pulse is received for 30 sec-
onds, the system will automatically switch
to standby operation. The settings are not
saved. EN

9000-610-72/30 1907V007 25
 Assembly

11 Controller

EN
N L3 PE L2 L1

s1 X13
X101 X14
X10 F7
F1 F2 F3 F4 F5 F6
X7

H3 H6
H2 H5
H1 H4

X2 X4 X5 X15 X6 X3
1 2 L1 PE L2 L3 L PE N L PE N L1 PE L2 L3 1 2

U V W PE U V W PE

M1 3
M M
1
M
1
M2 3
M

M3 M4

L1 L2 L3 N PE

X20

M5 M
1 M6 M
1

F1 Fuse T10AH
F2 Fuse T10AH
F3 Fuse T10AH
F4 Fuse T10AH
F5 Fuse T10AH
F6 Fuse T10AH
F7 Fuse T1.6AH
H1 Status indicator LED for temperature sensor, compressor unit 1
H2 Status indicator LED for temperature sensor, compressor unit 1
H3 Status indicator LED for temperature sensor, compressor unit 1
H4 Status indicator LED for temperature sensor, compressor unit 2
H5 Status indicator LED for temperature sensor, compressor unit 2
H6 Status indicator LED for temperature sensor, compressor unit 2
M1 Compressor unit 1
M2 Compressor unit 2
M3 Cooling fan motor, membrane drying unit 1
M4 Cooling fan motor, membrane drying unit 2 (Quattro Tandem only)

26 9000-610-72/30 1907V007
 Assembly

M5 Fan motor, compressor cabinet (Duo Tandem only)

M6 Fan motor, compressor cabinet (Duo Tandem only)
S1 Switch, main controller/auxiliary controller
X2 Temperature sensor, compressor unit 1 EN
X3 Temperature sensor, compressor unit 2
X4 Connection, compressor unit 1
X5 Connection, cooling fan motor, membrane drying unit 1
X6 Connection, compressor unit 2
X7 Network connection
X10 Network connection for connection to main controller/auxiliary controller
X13 Mains connection
X14 Operating panel connection on the control board
X15 Connection, cooling fan motor, membrane drying unit 2 (Quattro Tandem only)
X20 Mains connection 3/N/PE AC 400 V, 50 Hz - 60 Hz
X101 Connection, operating panel

9000-610-72/30 1907V007 27
 Usage

Service key Check of the safety valve

Usage and adjustment of the pres-
sure range (see "9.2
Checking the safety valve"
12 Operation and "10.1 Adjustment of
EN
Prior to working on the unit or in case of the switch-on/cut off pres-
danger, disconnect it from the mains. sure").
Standby button Switching between normal
operation and standby
12.1 Operating panel
mode (see"12.3 Normal
1 2 3 4 5 6 operation") and "12.4
Standby mode").

Pressure range
The pressure is displayed and can be adjusted in
this area.
The pressure is displayed via:
1. Blue LED (£ 4.5 bar):
only illuminates while the pressure is building up
during start-up operation
2. - 10. Blue LEDs (= 5 - 9 bar):
these indicate the pressure status in increments
1 Fault button with orange LED of 0.5 bar
2 Filter change button with orange LED 11. Orange LED (> 9 bar):
3 Service key with blue LED the pressure in the container is too high (i.e. out-
4 Standby button with blue LED side the adjustment range).
5 Pressure range display/adjustment Adjustment options (see "10.1 Adjustment of the
6 Pressure dew point display switch-on/cut off pressure").
Different messages and the status of the unit are Pressure dew point
displayed on the operating panel. In addition, dif- The current pressure dew point temperature is
ferent functions can be started via the buttons. displayed in this area. The compressed air can
The device is operated via the operating panel of cool down to this temperature without the water
the main control. The auxiliary control is inactive condensing.
(standby button flashing) and cannot be oper- The pressure dew point is displayed via:
ated. 4 blue LEDs: 0°C / 5°C / 10°C / 15°C
Buttons 1-2 blue LEDs light up when the system is run-
ning in the normal working range.
Fault button Display of alarm messages 1 orange LED: ³ 20°C, i.e. dry compressed air is
with different levels of no longer ensured.
importance. This can be As soon as the orange LED lights up the blue
faults, warning messages LEDs go out.
and information (see "12.7
Fault""12.8 Emergency
mode").
Filter replacement "Maintenance required" dis-
button play for the various filters
(see "13.2 Changing the fil-
ter").

28 9000-610-72/30 1907V007
 Usage

12.2 Switching the unit on/off 12.5 Auxiliary operation

❯ Switch the unit on and off via the surgery main If two compressors are operated in a singled
switch. compressed air network, then the two controls
The compressor unit will start up automatically need to be configured as a main control and an
and fill the pressure tank. When the cut-off auxiliary control. EN
pressure is reached the compressor unit Operation is deactivated on the control config-
switches itself off automatically. ured as the "auxiliary control" and the standby
button flashes.
12.3 Normal operation
The unit is in normal operation as soon as the 12.6 Set-up mode
plug is inserted in the power outlet. The com- The following can be carried out in set-up mode:
pressor runs until the cut off pressure is reached. – Adjusting the pressure range (see "10.1
The LEDs light up in the pressure range display. Adjustment of the switch-on/cut off pressure").
– Confirming filter replacement (see "13.2
Changing the filter").
– Deactivating emergency mode (see "12.8
Emergency mode").
❯ In standby mode, press the service key as well
to go into set-up mode.

12.7 Fault
The control monitors the functions of the unit and
signals faults according to their importance.
Faults, warnings or information can be displayed.
Faults are triggered as a result of faults in com-
12.4 Standby mode ponent assemblies or as a result of sensor
The following are possible in standby mode: defects. The unit is switched off and the LED of
– you can switch off the unit without disconnect- the fault button flashes or lights up.
ing it from the mains. Fault button, orange LED flashes
Normal mode or emergency mode can be acti-
– You can switch to set-up mode.
vated, see "12.8 Emergency mode").
❯ Switching from normal mode to standby mode: Fault button, orange LED lights up
Standby button: press for at least 2 sec-
As well as faults, the LED on the fault button also
onds. lights up to indicate warning messages and infor-
The LED comes on. mation.
The unit continues to operate in normal mode.
This keeps the operator informed about emer-
gency mode, humidity, leaks or overheating.
Warning messages and information are automati-
cally deactivated after the fault has been rectified,
with exception of emergency mode.

12.8 Emergency mode

If a unit fails, the compressor can be switched to
emergency mode:
Fault button, orange LED flashes.
❯ Press the standby button again to switch to 1 aggregate has failed.
normal mode. ❯ Flashing fault button: press the button.
The compressor continues to run with one unit.
The fault button lights up to indicate that emer-
gency mode is active.

9000-610-72/30 1907V007 29
 Usage

❯ Have the necessary repairs to the unit carried

out.

EN

30 9000-610-72/30 1907V007
 Usage

13 Maintenance
Prior to working on the unit or in case of danger, disconnect it from the mains.
EN
VORSICHT
Risk of infection due to burst filters
Particles enter the compressed air network and can therefore enter the mouth of the patient.
❯ Replace filters in accordance with the maintenance schedule.

13.1 Maintenance schedule

ACHTUNG
Risk of damage to the unit due to blocked filters
Continuous running due to reduced delivery. Damage to the unit due to burst filters.
❯ Replace filters in accordance with the maintenance schedule.

Maintenance Maintenance work

interval
At regular intervals ❯ Empty the collector tray under the membrane drying unit (the interval may vary
depending on the ambient conditions and method of working; empty it daily if
the humidity is high).
Annually ❯ Replace the air intake filter in the compressor unit – every six months if the
concentration of dust is high.
❯ Replace the fine or sterile filter.
❯ Replace the sintered filter.
Every 4 years ❯ Replace the vibration dampers.
In accordance with ❯ Check the safety valve.
national law ❯ Carry out recurring safety inspections (e.g. pressure tank inspections, electrical
safety inspections) in accordance with applicable national laws.

9000-610-72/30 1907V007 31
 Usage

❯ Remove the air intake filter.

13.2 Changing the filter
ACHTUNG
Shortened service life, bad air quality,
EN reduced delivery
❯ Replace the filter 1x per year or as
soon as the yellow LED lights up.
Filter replacement button, yellow LED lights
up.
As soon as the LED lights up, it can be
temporarily switched off by pressing the
button. Every time the unit is switched
back on the LED comes on again.
The LED only goes out permanently once
replacement of the filter has been con-
firmed in set-up mode.

Disconnecting the unit from the mains ❯ Insert a new air intake filter.
❯ Standby button: press for at least 2 sec- ❯ Replace the noise reducer.
onds.
Changing the fine/sterile filter of the mem-
❯ Unplug the mains plug. brane drying unit
Replacing the air intake filter ❯ Switch off the unit.
❯ Remove the noise reducer. ❯ Disconnect all power from the device.
❯ Unscrew and remove the filter cover.
❯ Remove the fine/sterile filter.
❯ Insert the new fine/sterile filter.
❯ Replace the filter cover and close.

Replacing the sintered filter of the membrane

drying unit
❯ Unscrew and remove the filter housing.
❯ Remove the sintered filter.
❯ Insert a new sintered filter.

32 9000-610-72/30 1907V007
 Usage

❯ Replace the filter housing and close. 14 Taking out of use

14.1 Taking the unit out of use
If the compressor is not to be used for a longer
period of time, it is recommended that the unit be EN
properly shut down and taken out of operation.
To do so, any accumulated condensation water
must be drained from the pressure tank and from
the membrane drying unit.
The compressor must be running in order
to drain the remaining condensation
water in the water separator of the mem-
brane drying unit.
❯ Open the condensate drain valve on the mem-
brane drying unit (approx. 3 turns).

Confirming the filter replacement

❯ Connect the mains plug.
❯ press for at least 2 seconds.
❯ press for at least 2 seconds. The unit is
now in setup mode.
Orange LED flashes
❯ Press to confirm filter replacement.
Resetting the unit to normal operation
❯ Touch.
Resetting the unit to standby mode
❯ Touch.

9000-610-72/30 1907V007 33
 Usage

❯ At maximum tank pressure, slowly open the ❯ Close the condensate drain valve on the pres-
condensate drain valve. sure tank.

EN

Once the start-up pressure has been reached the ❯ Close the condensate drain valve on the mem-
compressor will switch on. brane drying unit.
On Quattro-Tandem models (2 membrane
drying units) both units must switch on.

❯ Wait until condensation water stops escaping

from the condensate drain valve on the mem-
brane drying unit.
❯ Switch off the unit - touch for at least 2
seconds.
❯ Wait until air stops escaping from the conden-
sate drain valve (pressure tank empty).
❯ Unplug the mains plug.

❯ Disconnect the compressor from the pipe sys-

tem.

14.2 Storage of the unit

WARNING
Risk of explosion of the pressure tank
and pressure hoses
❯ The pressure tank and the pressure
hoses must be vented before they are
stored or transported.

34 9000-610-72/30 1907V007
 Usage

❯ Protect the unit against moisture, dirt and

extreme temperatures during transport (refer to
the section on "Ambient conditions").
❯ Only store the unit when it has been completely
emptied.
EN

9000-610-72/30 1907V007 35
 Troubleshooting

Troubleshooting

15 Tips for operators and service technicians

EN
Any repairs exceeding routine maintenance may only be carried out by qualified personnel or our
service.

Prior to working on the unit or in case of danger, disconnect it from the mains.

Error Possible cause Remedy

LED on the filter replacement Filter replacement required ❯ Replace the intake filter, fine/
button lights up sterile filter and sintered filter
(see "13.2 Changing the fil-
ter").
Compressor will not start No display on the operating ❯ Check the main power switch,
panel mains fuse and mains voltage,
No mains voltage inform an electrician if neces-
sary.
Fault button flashes (if compres- ❯ Activate emergency mode:
sor is equipped with 2 units) Press the fault button, (see
Emergency mode possible "12.8 Emergency mode").
Compressor runs with 1 unit.
❯ Inform a service technician
Fault button lit up ❯ Disconnect the mains plug
Compressor defective and inform a service techni-
cian.
Compressor starts up, no dis- Operating panel defective ❯ Disconnect the mains plug
play on the operating panel and inform a service techni-
cian.

36 9000-610-72/30 1907V007
 Troubleshooting

Error Possible cause Remedy

Compressor does not switch Excessive air extraction ❯ Check air requirements and
off or has difficulty reaching dimensioning of the compres-
the cut off pressure sor.
Air intake filter dirty ❯ Replace the air intake filter.
EN
Leak in the compressed air pipe ❯ Check the compressed air
network pipe network, if necessary
disconnect the mains plug
and inform a service techni-
cian.
Leak in the compressed air lines ❯ Check the pressure hoses on
of the compressor station the compressor, membrane
drying unit and distributor
block; if necessary disconnect
the mains plug and inform a
service technician.
Flow noise at the membrane ❯ Check the pressure hoses on
drying unit the compressor; if necessary
inform a service technician.
Change in the delivery of the ❯ Disconnect the mains plug
compressor unit and inform a service techni-
cian.
Compressor blows via the safety ❯ Disconnect the mains plug
valve, and inform a service techni-
The container pressure is not cian.
displayed correctly on the oper-
ating panel
Compressor switches on with- Leak in the compressed air pipe ❯ Check the compressed air
out any compressed air being system pipe system; if necessary dis-
extracted connect the plug and inform a
service technician.
Leak in the compressed air lines ❯ Check the pressure hoses on
of the compressor the compressor, membrane
drying unit and distributor
block; if necessary disconnect
the mains plug and inform a
service technician.
Fault button flashing Compressor unit defective ❯ Activate emergency mode:
press the fault button, (see
"12.8 Emergency mode").
Compressor runs with 1 unit
❯ Inform a service technician.
Fault button lit up Unit is defective ❯ Unplug the mains plug.
❯ Inform a service technician.
Knocking or loud noises on Compressor unit defective ❯ Inform a service technician.
the compressor

9000-610-72/30 1907V007 37
 Appendix

Appendix

16 Handover protocol
EN
This document confirms the qualified handover and provision of instructions for the medical device from
Dürr Dental. This must be carried out by a qualified adviser for the medical device, who will instruct you
in the proper handling and operation of the medical device.
Product name Order number (REF) Serial number (SN)

o Visual inspection of the packaging for any damage

o Unpacking the medical device and checking for damage
o Confirmation of the completeness of the delivery
o Instruction in the proper handling and operation of the medical device based on the operating
instructions

Notes:

Name of person receiving instruction: Signature:

Name and address of the qualified adviser for the medical device:

Date of handover: Signature of the qualified adviser for the

medical device:

38 9000-610-72/30 1907V007
Hersteller/Manufacturer:
DÜRR DENTAL SE
Höpfigheimer Str. 17
74321 Bietigheim-Bissingen
Germany
Fon: +49 7142 705-0
www.duerrdental.com
[email protected]