Service Information System Page 1 of 4
Operation and Maintenance Manual
D10T Track-Type Tractor
Media Number -SEBU7764-02 Publication Date -01/11/2005 Date Updated -31/01/2006
i02370428
Maintenance Interval Schedule
SMCS - 7000
Ensure that all safety information, warnings, and instructions are read and understood before any
operation or any maintenance procedures are performed.
The user is responsible for the performance of maintenance, including all adjustments, the use of
proper lubricants, fluids, filters, and the replacement of components due to normal wear and aging.
Failure to adhere to proper maintenance intervals and procedures may result in diminished
performance of the product and/or accelerated wear of components.
Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, in
order to determine the maintenance intervals. Products that operate in severe operating conditions
may require more frequent maintenance.
Note: Before each consecutive interval is performed, all maintenance from the previous interval
must be performed.
When Required
Cutting Edges and End Bits - Inspect/Replace
Engine Air Filter Primary Element - Clean/Replace
Engine Air Filter Secondary Element - Replace
Engine Air Precleaner - Clean
Ether Starting Aid Cylinder - Replace
Fuel System - Prime
Fuses and Circuit Breakers - Replace/Reset
High Intensity Discharge Lamp (HID) - Replace
Hydraulic System Return Screen - Clean
Oil Filter - Inspect
Radiator Core - Clean
Radiator Pressure Cap - Clean/Replace
Ripper Tip and Shank Protector - Inspect/Replace
Window Washer Reservoir - Fill
Window Wipers - Inspect/Replace
Windows - Clean
Daily
Walk-Around Inspection
Every 10 Service Hours or Daily
Backup Alarm - Test
Braking System - Test
Cab Filter (Fresh Air) - Clean/Inspect/Replace
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias... 2/3/2006
Service Information System Page 2 of 4
Cooling System Coolant Level - Check
Engine Oil Level - Check
Equalizer Bar End Pins Oil Level - Check
Fuel System Water Separator - Drain
Horn - Test
Hydraulic System Oil Level - Check
Indicators and Gauges - Test
Pivot Shaft Oil Level - Check
Seat Belt - Inspect
Transmission System Oil Level - Check
Every 50 Service Hours or Weekly
Bulldozer - Lubricate
Cab Filter (Recirculation) - Clean/Inspect/Replace
Fuel Tank Water and Sediment - Drain
Lift Cylinder Yoke Bearings - Lubricate
Ripper Linkage and Cylinder Bearings - Lubricate
Track Pins - Inspect
Initial 250 Service Hours
Engine Valve Lash - Check/Adjust
Initial 250 Service Hours (or at first oil change)
Transmission and Torque Converter Oil Filters - Replace
Every 250 Service Hours
Belts - Inspect/Adjust/Replace
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Final Drive Oil Level - Check
Track - Check/Adjust
Initial 500 Hours (for New Systems, Refilled Systems, and Converted Systems)
Cooling System Coolant Sample (Level 2) - Obtain
Every 500 Service Hours
Engine Crankcase Breather - Clean
Final Drive Oil Sample - Obtain
Final Drive Seal Guard - Inspect/Clean
Fuel System Primary Filter - Clean/Replace
Fuel System Secondary Filter - Replace
Hydraulic System Oil Filters - Replace
Hydraulic System Oil Sample - Obtain
Recoil Spring Compartment Oil Level - Check
Transmission Breather - Clean
Transmission System Oil Sample - Obtain
Transmission and Torque Converter Oil Filters - Replace
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias... 2/3/2006
Service Information System Page 3 of 4
Every 500 Service Hours or 3 Months
Engine Oil and Filter - Change
Initial 1000 Service Hours
Electronic Unit Injector - Inspect/Adjust
Engine Valve Rotators - Inspect
Every 1000 Service Hours or 6 Months
Battery - Inspect
Engine Valve Lash - Check/Adjust
Rollover Protective Structure (ROPS) - Inspect
Transmission System Oil and Screens - Change/Clean
Every 2000 Service Hours or 1 Year
Aftercooler Core - Inspect/Clean
Air Conditioner Condenser - Clean
Engine Mounts and Equalizer Bar - Inspect
Final Drive Oil - Change
Final Drive Seal Guard Packing - Replace
Hydraulic System Oil - Change
Hydraulic System Oil Filter (Pilot) - Replace
Track Roller Frame - Inspect
Track Roller Frame Guides - Inspect
Every Year
Cooling System Coolant Sample (Level 2) - Obtain
Engine Air Filter Primary Element - Replace
Refrigerant Dryer - Replace
Every 3 Years After Date of Installation or Every 5 Years After Date of
Manufacture
Seat Belt - Replace
Every 6000 Service Hours or 3 Years
Bearing Block Seal - Replace
Cooling System Coolant Extender (ELC) - Add
Cooling System Water Temperature Regulator - Replace
Electronic Unit Injector - Inspect/Adjust
Engine Valve Lash - Check/Adjust
Engine Valve Rotators - Inspect
External Engine Components - Inspect
Every 12 000 Service Hours or 6 Years
Cooling System Coolant (ELC) - Change
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias... 2/3/2006
Service Information System Page 4 of 4
Copyright 1993 - 2006 Caterpillar Inc. Fri Feb 3 01:51:38 UTC+0700 2006
All Rights Reserved.
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias... 2/3/2006
