RTXM228-401 (Preliminary Datasheet)

10Gbit/s 10Km SFP+ 1310 nm Transceivers

RTXM228-401 Preliminary

Features
„ Compliant to SFP+ MSA
„ Fully RoHS Compliant
„ All metal housing for superior EMI performance
„ IPF compliant mechanics (SFF-8432 Rev 4.3)
„ Operating data rate 9.953-10.3125Gbps
„ Uncooled 1310nm DFB Laser
„ High sensitivity PIN photodiode and TIA
RTXM228-401
„ Link lengths at 10Km
„ LC duplex connector
Applications
„ Hot pluggable 20pin connector
„ 10GBASE-LR/LW 10G Ethernet „ Low power consumption <1.0W
„ 0℃ to 70℃ operating wide temperature range
„ Single +3.3V±5% power supply
Standard „ Digital Monitoring SFF-8472 Rev 10.2 compliant
„ Real time monitoring of：
„ IEEE 802.3ae 10GBASE-LR/LW
- Transmitted optical power
„ SFF-8431 Rev 3.0
- Received optical power
„ SFF-8472 Rev 10.2
- Laser bias current
- Temperature
- Supply voltage
Description
The RTXM228 1310nm DFB 10Gigabit Transceiver is designed to transmit and receive serial optical
data over single mode optical fiber with 10Km.They are compliant with SFF-8431,SFF-8432 and
IEEE802.3ae 10GBASE-LR/LW.The transmitter converts serial CML electrical data into serial optical data
compliant with the 10GBASE-LR standard. An open collector compatible Transmit Disable (Tx_Dis) is
provided. When TX_DIS is asserted High, Transmitter is turned off. The receiver converts serial optical
data into serial CML electrical data. An open collector compatible Loss of Signal is provided. The
RX_LOS signal indicates insufficient optical power for reliable signal reception at the receiver. Digital
diagnostics functions are available via a 2-wire serial interface, as specified in SFF-8472 .

Block diagram
Wuhan Telecommunication Devices Co., Ltd. 1 World Wide Web:http://www.wtd.com.cn
88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)

TOSA Laser Driver S

F
P
+
Controller C
O
MCU N
N
FLASH E
ROSA C
T
TIA Post Amplifier O
R

Figure 1.Transceiver functional diagram

Absolute Maximum Ratings
Parameter Symbol Unit Min Max
o
Storage Temperature Range Ts C -40 85
Relative Humidity RH % 0 95
o
Powered Case Temperature Range Tc C 0 70

Recommended Operating Conditions

Parameter Symbol Unit Min Typ Max

o
Operating Case Temperature Range Tc C 0 70
Power Supply Voltage Vcc V 3.14 3.3 3.46
Bit Rate BR Gb/s 9.953 10.3125
Bit Error Ratio BER 10-12
Max Supported Link Length L Km 10

Electrical Characteristics (Tc=0 oC to 70 oC and Vcc= 3.14 to 3.46)

Parameter Symbol Unit Min Typ Max Note
Supply Voltage VCC V 3.14 3.3 3.46
Supply Current Icc mA 200 285
Transmitter
Input Differential Impedance RIN Ω 80 100 120 1
Differential Data Input Swing VIN mVp-p 180 700
Transmit Disable Voltage VDIS V 2 VCCHOST
Transmit Enable Voltage VEN V VEE VEE+0.8
Transmit Fault Assert Voltage VFA V 2.2 VCCHOST
Transmit Fault De-Assert Voltage VFDA V VEE VEE+0.4
Receiver
Differential Data Output Swing VOD mVp-p 300 850
Wuhan Telecommunication Devices Co., Ltd. 2 World Wide Web:http://www.wtd.com.cn
88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
Output Rise Time tRISE pS 25
Output Fall Time tFALL pS 25
LOS Fault VLOSFT V 2 VCCHOST
LOS Normal VLOSNR V VEE VEE+0.8
NOTE:
1. Differential between TD+ / TD–

Optical Characteristics (Tc=0 oC to 70 oC and Vcc= 3.14 to 3.46)

Parameter Symbol Unit Min Typ Max Note
Transmitter
Nominal Wavelength λTRP nm 1290 1310 1330
Side Mode Suppression Ratio SMSR dB 30
Optical Modulation Amplitude POMA dBm -5.2
Optical Output Power Pav dBm -8.2 0.5 1
Extinction Ratio ER dB 3.5
Transmitter and Dispersion Penalty TDP dB 3.2
Launch Power in OMA Minus TDP dBm -6.2
Average Launch Power of OFF
POFF dBm -30
Transmitter
Relative Intensity Noise RIN dB/Hz -128
Optical Return Loss Tolerance ORLT dB 12
Eye Mask(X1,X2,X3,Y1,Y2,Y3) (0.25, 0.40, 0.45, 0.25, 0.28, 0.40) 2
Receiver
Center Wavelength λC nm 1290 1310 1330
LOS Detect Asserted PLOS dBm -20
Optical Return Loss ORL dB -14
Average Receiver Power PAVG dBm -14.4 +0.5 3
Receiver Sensitivity (OMA) RSENSE1 dBm -12.6
Stressed Receiver Sensitivity RSENSE2 dBm -10.3 4
Receiver Reflectance RREFL dB -12
Vertical Eye Closure Penalty dB 2.2
Stressed Eye Jitter JStr UI 0.3
Receive Electrical 3 dB Upper Cutoff
FCUT GHz 12.3
Frequency
LOS Assert LOS LOSD dBm -30
LOS De-Assert LOS LOSA dBm -17
LOS Hysteresis dB 0.5
Note:
1 Minimum output optical level is at end of life
2 Refer to figure2
3 Sensitivity for 10G PRBS 231-1 and BER better than or equal to 10E-12
4 The stressed sensitivity value in the table are for system level BER measurements which include the
effects of CDR circuit.
Wuhan Telecommunication Devices Co., Ltd. 3 World Wide Web:http://www.wtd.com.cn
88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)

Figure 2. Transmitter eye mask definition

Pin function definitions

Figure 3.Pin function definitions

Table 1.Transceiver pin descriptions
Pin Number Symbol Name Description
These pins should be connected to signal ground
1,17,20 VeeT Transmitter Signal Ground
on the host board.
Logic “1” Output = Laser Fault (Laser off before
t_fault)
2 TX Fault Transmitter Fault Out (OC) Logic “0” Output = Normal Operation
This pin is open collector compatible, and should
be pulled up to Host Vcc with a 10kΩ resistor.
Logic “1” Input (or no connection) = Laser off
3 TX Disable Transmitter Disable In (LVTTL) Logic “0” Input = Laser on
This pin is internally pulled up to VccT with a 10
kΩ resistor.
4 SDA
Serial ID with SFF 8472 Diagnostics
5 SCL Module Definition Identifiers Module Definition pins should be pulled up to
Host Vcc with 10 kΩ resistors.
6 MOD-ABS
7 RS0 Receiver Rate Select (LVTTL) These pins have an internal 30kΩ pull-down to

Wuhan Telecommunication Devices Co., Ltd. 4 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
Transmitter Rate Select (LVTTL) ground. A signal on either of these pins will not
9 RS1
affect module performance.
Sufficient optical signal for potential
BER < 1x10-12 = Logic “0”
Insufficient optical signal for potential
8 LOS Loss of Signal Out (OC)
BER < 1x10-12 = Logic “1”
This pin is open collector compatible, and should
be pulled up to Host Vcc with a 10kΩ resistor.
These pins should be connected to signal ground
10,11,14 VeeR Receiver Signal Ground
on the host board.

Light on = Logic “0” Output Receiver DATA

Receiver Negative DATA Out
12 RD- output is internally AC coupled and series
(CML)
terminated with a 50Ω resistor.

Light on = Logic “1” Output Receiver DATA

Receiver Positive DATA Out
13 RD+ output is internally AC coupled and series
(CML)
terminated with a 50Ω resistor.

This pin should be connected to a filtered +3.3V

15 VccR Receiver Power Supply power supply on the host board. See Figure
3.Recommended power supply filter

This pin should be connected to a filtered +3.3V

16 VccT Transmitter Power Supply power supply on the host board. See Figure
3.Recommended power supply filter

Logic “1” Input = Light on Transmitter DATA

Transmitter Positive DATA In
18 TD+ inputs are internally AC coupled and terminated
(CML)
with a differential 100Ω resistor.
Logic “0” Input = Light on Transmitter DATA
Transmitter Negative DATA In
19 TD- inputs are internally AC coupled and terminated
(CML)
with a differential 100Ω resistor.

Typical application circuit

Recommended “Typical Application Schematics” are shown in Figure 3.
+3.3V

R R R R R
4.7-10K x 5
11 10
VEER VEER

RD- GNDR12 RD- RS1

9 GNDR
RS1
13 8
RD+ RD+ RX_LOS RX-LOS
L 14 7
C C VEER RS0 RS0
C 4.7uH
0.1uF 22uF 0.1uF GNDR15 6
VCCR MOD_ABS MOD-ABS
16 5
+3.3V VCCT SCL SCL
L
C 4.7uH C C 17 4
VEET SDA SDA
0.1uF 22uF 0.1uF
TD+ GNDT18 TD+ TX_DISABLE
3
TX-DIS
19 2
TD- TD- TX_FAULT TX-FAULT
20 1
VEET VEET
GNDT GNDT
SFP+ MODULE

Figure 3.Typical application schematics

Wuhan Telecommunication Devices Co., Ltd. 5 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
Electorstatic Discharge(ESD)
The RTXM228 is compatible with ESD levels found in typical manufacturing and operating environments
as described in Table 2. In the normal handling and operation of optical transceivers, ESD is of concern in
two circumstances.
The first case is during handling of the transceiver prior to insertion into an SFP+ compliant cage. To
protect the device, it’s important to use normal ESD handling pre-cautions. These include use of grounded
wrist straps, work-benches and floor wherever a transceiver is handled.
The second case to consider is static discharges to the exterior of the host equipment chassis after
installation. If the optical interface is exposed to the exterior of host equipment cabinet, the transceiver
may be subject to system level ESD requirements.

Electromagnetic Interference (EMI)

Equipment incorporating gigabit transceivers is typically subject to regulation by the FCC in the United
States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. The RTXM228 compliance to
these standards is detailed in Table 2. The metal housing and shielded design of the RTXM228 minimizes
the EMI challenge facing the equipment designer.

EMI Immunity (Susceptibility)

Due to its shielded design, the EMI immunity of the RTXM228 exceeds typical industry standards.

Flammability
The RTXM228 optical transceiver is made of metal and high strength, heat resistant, chemical resistant and
UL 94V-0 flame retardant plastic.
Table 2. Regulatory compliance
Feature Test Method Performance
Electrostatic Discharge (ESD) to
MIL-STD-883C Method 3015.4 Class 1 (> 2000 Volts)
the Electrical Pins
Typically, no damage occurs with
Electrostatic Discharge (ESD) to 25 kV when the duplex LC
Variation of IEC 61000-4-2
the Duplex LC Receptacle connector receptacle is contacted
by a Human Body Model probe.
Electromagnetic CISPR22 ITE Class B
Compliant with standards
Interference (EMI) EN55022 Class B
Typically show no measurable
effect from a 3V/m field swept
IEC61000-4-3 Class 2
Immunity from 80 to 1000MHz applied to
EN55024
the transceiver without a chassis
enclosure.
Less than 1000 ppm of cadmium,
lead, mercury, hexavalent
RoHS Compliance chromium, polybrominated
biphenyls, and polybrominated
biphenyl ethers.

Digital Diagnostic Interface Definition

The 2-wire serial interface addresses of the SFP+ module are 1010000x (A0h) and 1010001x (A2h).
Shown in Figure 4.

Wuhan Telecommunication Devices Co., Ltd. 6 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)

Figure 4. Digital Diagnostic Memory Map

Accessing Serial ID Memory uses the 2 wire address 1010000X (A0). Memory Contents of Serial ID are
shown in Table 3.
Table 3 Serial ID Memory Contents
Data Size
Name of Field Contents(Hex) Description
Address (Bytes)
BASE ID FIELDS
0 1 Identifier 80 SFP+
1 1 Ext. Identifier 04 SFP function is defined by serial ID
only
2 1 Connector 07 LC Connector
3-10 8 Transceiver Transceiver Codes
11 1 Encoding 03 NRZ
12 1 BR, Nominal 10Gbit/s
13 1 Reserved
14 1 Length (9μm) km Transceiver transmit distance
15 1 Length (9μm) 100m
16 1 Length (50μm) 10m
17 1 Length(62.5μm)10m
18 1 Length (Copper) 00 Not compliant
19 1 Reserved 00
20-35 16 Vendor name 57 54 44 20 20 20 20 20 “WTD”(ASCII)
20 20 20 20 20 20 20 20
36 1 Reserved 00
37-39 3 Vendor OUI 00 00 00
40-55 16 Vendor PN Transceiver part number
56-59 4 Vendor rev 20 20 20 20
60-61 2 Wavelength Transceiver wavelength
62 1 Reserved 00
63 1 CC_BASE Check Sum (Variable) Check code for Base ID Fields
EXTENDED ID FIELDS
64-65 2 Options 00 1A TX_DISABLE, TX_FAULT and
Loss of Signal implemented.
66 1 BR,max 00
Wuhan Telecommunication Devices Co., Ltd. 7 World Wide Web:http://www.wtd.com.cn
88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
67 1 BR,min 00
68-83 16 Vendor SN 42 30 30 39 38 32 32 20 Serial Number of transceiver
20 20 20 20 20 20 20 20 (ASCII). For example “B009822”.
84-91 8 Date code 30 32 31 30 30 35 20 20 Manufactory date code. For
example “021005”.
92 1 Diagnostic 58 Digital diagnostic monitoring
Monitoring Type implemented, “externally
calibrated” is implemented, RX
measurement type is “Average
Power”.
93 1 Enhanced Options B0 Optional Alarm/Warning flags
implemented for all monitored
quantities, Optional Soft
TX_FAULT monitoring
implemented, Optional Soft
RX_LOS monitoring implemented.
94 1 SFF_8472 01 Includes functionality described in
Compliance Rev9.3 SFF-8472.
95 1 CC_EXT Check Sum (Variable) Check sum for Extended ID Field.
VENDOR SPECIFIC ID FIELDS
96-127 32 Vendor Specific Read only Depends on customer information
128-255 128 Reserved Read only Filled by zero

Diagnostic Monitor Functions

Diagnostic Monitor Functions interface uses the 2 wire address 1010001X (A2). Memory contents of
Diagnostic Monitor Functions are shown in Table 4
Table 4 Memory contents of Diagnostic Monitor Function
Data Field Size Name Contents and Description
Address (bytes)
Alarm and Warning Thresholds
00-01 2 Temperature High Alarm Set to 70 OC
02-03 2 Temperature Low Alarm Set to -5 OC
04-05 2 Temperature High Warning Set to 65 OC
06-07 2 Temperature Low Warning Set to 0 OC
08-09 2 Vcc High Alarm Set to 3.6 V
10-11 2 Vcc Low Alarm Set to 3.0 V
12-13 2 Vcc High Warning Set to 3.5 V
14-15 2 Vcc Low Warning Set to 3.1 V
16-17 2 Bias High Alarm 2×IBias+20 (25 oC)
18-19 2 Bias Low Alarm 25%×IBias (25 oC)
20-21 2 Bias High Warning 2×IBias +10

Wuhan Telecommunication Devices Co., Ltd. 8 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
22-23 2 Bias Low Warning 50%×IBias (25 oC)
24-25 2 TX Power High Alarm Manufacture measurement plus 2dB
26-27 2 TX Power Low Alarm Manufacture measurement minus 2dB
28-29 2 TX Power High Warning Manufacture measurement plus 1dB
30-31 2 TX Power Low Warning Manufacture measurement minus 1dB
32-33 2 RX Power High Alarm Maximum input optical power
34-35 2 RX Power Low Alarm Minimum input optical power
36-37 2 RX Power High Warning Maximum input power minus 3dB
38-39 2 RX Power Low Warning Manufacture measurement plus 3dB
40-55 16 Reserved
Calibration Constants
56-59 4 RX Power Calibration Data4 Single precision floating-point numbers
60-63 4 RX Power Calibration Data3 (various values at each device)
64-67 4 RX Power Calibration Data2 Single precision floating-point numbers
68-71 4 RX Power Calibration Data1 (various values at each device)
72-75 4 RX Power Calibration Data0
76-77 2 Bias Calibration Data1 00 01 (fixed)
78-79 2 Bias Calibration Data0 00 00 (fixed)
80-81 2 TX Power Calibration Data1 00 01 (fixed)
82-83 2 TX Power Calibration Data0 00 00 (fixed)
84-85 2 Temperature Calibration Data1 00 01 (fixed)
86-87 2 Temperature Calibration Data0 00 00 (fixed)
88-89 2 Vcc Calibration Data1 00 01 (fixed)
90-91 2 Vcc Calibration Data0 00 00 (fixed)
92-94 3 Reserved 00 00 00 (fixed)
95 1 Check Sum Checksum of bytes 0-94
Real Time Diagnostic Monitor Interface
96-97 2 Measured Temperature Yield a 10-bit A/D value
98-99 2 Measured Vcc Yield a 10-bit A/D value
100-101 2 Measured Bias Yield a 10-bit A/D value
102-103 2 Measured TX Power Yield a 10-bit A/D value
104-105 2 Measured RX Power Yield a 10-bit A/D value
106-109 4 Reserved
110 1 Logic Status
111 1 AD Conversion Updates
112-119 8 Alarm and Warning Flags
Vendor Specific
120-127 8 Vendor Specific Don’t Access
128-247 120 User writable EEPROM
248-255 8 Vendor Specific Don’t Access

Wuhan Telecommunication Devices Co., Ltd. 9 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
Table 5. Transceiver Timing Characteristics
(Tc=0 oC to 70 oC and VccT, VccR = 3.145 to 3.465)
Parameter Symbol Minimum Maximum Unit Notes
Hardware TX_DISABLE Assert Time t_off 10 μs 1
Hardware TX_DISABLE Negate
t_on 1 ms 2
Time
Time to initialize including reset of
t_init 300 ms 3
TX_FAULT
Hardware TX_FAULT Assert Time t_fault 100 μs 4
Hardware TX_DISABLE to Reset t_reset 10 μs 5
Hardware RX_LOS DeAssert Time t_loss_on 100 μs 6
Hardware RX_LOS Assert Time t_loss_off 100 μs 7
Software TX_DISABLE Assert Time t_off_soft 100 ms 8
Software TX_DISABLE Negate Time t_on_soft 100 ms 9
Software Tx_FAULT Assert Time t_fault_soft 100 ms 10
Software Rx_LOS Assert Time t_loss_on_soft 100 ms 11
Software Rx_LOS De-Assert Time t_loss_off_soft 100 ms 12
Analog parameter data ready t_data 1000 ms 13
Serial bus hardware ready t_serial 300 ms 14
Write Cycle Time t_write 10 ms 15
Serial ID Clock Rate f_serial_clock 400 kHz
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below
10% of nominal. Measured from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output
rises above 90% of nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is
functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.

Wuhan Telecommunication Devices Co., Ltd. 10 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
Package outline（Unit: mm）

Wuhan Telecommunication Devices Co., Ltd. 11 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]
 RTXM228-401 (Preliminary Datasheet)
Ordering Information
Specifications
Part No. Data Optical Application
Package Laser Detector Sensitivity Temp Reach Other
rate Power
9.95G 1310nm -8.2
RTXM228-401 SFP+ PIN < -14.4dBm 0~70oC 10km DDM 10GBASE-LR/LW
~10.31G DFB ~+0.5dBm

Consultation
Product purchasing Applications Technical Support
China: Marketing&Planning Dept.
Domestic Trade Dept. Tel: (86)27-8769 1435
Tel: (86)27-8769 1746 Fax: (86)27-8780 3010
Fax: (86)27-8780 3010 E-mail:[email protected]
E-mail:[email protected] General Information
Elsewhere: Marketing&Planning Dept.
International Trade Dept. Tel: (86)27-8769 3454
Tel: (86)27-8769 1194 Fax: (86)27-8780 3010
Fax: (86)27-8780 3010 E-mail:[email protected]
E-mail:[email protected]

WTD CO.,LTD reserves the right to make changes to the product(s) or information contained herein
without notice. No liability is assumed as a result of their use or application. No rights under any patent
accompany the sale of any such product(s) or information.
Edition 2005-09-30
Published by Wuhan Telecommunications Devices Co.,Ltd.
Copyright © WTD CO.,LTD
All Rights Reserved.

==============================================================
Note:

Wuhan Telecommunication Devices Co., Ltd. 12 World Wide Web:http://www.wtd.com.cn

88 Youkeyuan Road,Hongshan District Fax:+86(27)8780 3010
Wuhan,Hubei 430074,P.R.C. E-mail:[email protected]