https://www.wy-international.
com/
https://www.ebay.com/str/tiamofaye/
WP8025ADAM User’s Manual V1.42
WP8025ADAM
User’s Manual
Version 1.42
WP8025ADAM User’s Manual V1.42
、
1 Product description
8ch relay output (SPST).
Using RS485 MODBUS RTU communication standard. It can be netted with configuration software, PLC and industry
touch pad
Communication, input and output status LED
Communication circuit designed for lightening protection and interference immunity
Could be used for signal collection and control of Industrial field apparatus
3 Year’s quality assurance for normal use
2 、Specification
Relay output 8ch (SPST)
Relay contact capacity 2A/250VAC 2A/30VDC
Working Temperature ～ ℃
-20 70
External power supply ～
DC 9V 30V/2W
Isolation protect 1500VDC
Installation method Standard DIN slide rail or screw
Dimension 125×73×35mm
3 、Interface definition
AVcc External PSU positive terminal input
AGnd External PSU negative terminal input
RY1A Normally open contact A of the relay output in 1st way
RY1B Normally open contact B of the relay output in 1st way
RY2A Normally open contact A of the relay output in 2nd way
RY2B Normally open contact B of the relay output in 2nd way
RY3A Normally open contact A of the relay output in 3rd way
RY3B Normally open contact B of the relay output in 3rd way
RY4A Normally open contact A of the relay output in 4th way
RY4B Normally open contact B of the relay output in 4th way
RY5A Normally open contact A of the relay output in 5th way
RY5B Normally open contact B of the relay output in 5th way
RY6A Normally open contact A of the relay output in 6th way
RY6B Normally open contact B of the relay output in 6th way
RY7A Normally open contact A of the relay output in 7th way
RY7B Normally open contact B of the relay output in 7th way
RY8A Normally open contact A of the relay output in 8th way
RY8B Normally open contact B of the relay output in 8th way
485A RS485 signal A+
485B RS485 signal B-
4 、Relay output application diagram
WP8025ADAM User’s Manual V1.42
5 、Communication Instruction
5.1 、Communication parameter (default setting)： 9600，N，8，1
Parameter Description
9600 baud rate
N(no check) check bit
8 data bit
1 stop bit
5.2 、Command for digital output (several controls)：
Send: 01 0F 00 00 00 08 01 A4 FF 2E （example/hexadecimal）
data byte data description remark
01 1 module address address range 01-FE
0F 1 function code 0F-write multiple coil
0000 2 coil address(0x mode) 0000-initial address of coil
0008 2 write coil length 0008-write 4 coils
01 1 write data byte 01-write one byte data
A4 2 write data A4-write 8 coil’s output status
FF2E 2 check code CRC check code for all data
Receive: 01 0F 00 00 00 08 54 0D （example/hexadecimal）
Converting input data “A4” to 2 hexadecimal results “10100100”. From left to right, it represent the 8 relay output status
、
RY8-RY1,here it means RY8 RY6 and RY3 has output but others no.Module will take corresponding action after receiving
correct command and send the response back to master. It means successful communication.
5.3 、Command for digital output (single control)：
Send: 01 05 00 00 FF 00 8C 3A （example/hexadecimal）
01 1 module address address range 01-FE
05 1 function code 05-write single coil
0000 2 coil address(0x mode) 0000-relay output(RY1)coil address
0001-relay output(RY2)coil address
0002-relay output(RY3)coil address
0003-relay output(RY4)coil address
0004-relay output(RY5)coil address
0005-relay output(RY6)coil address
0006-relay output(RY7)coil address
0007-relay output(RY8)coil address
FF00 2 write data ，
FF00-coil open 0000-coil close
8C3A 2 check code CRC check code for all data
01 1 module address address range 01-FE
Receive: 01 05 00 00 FF 00 8C 3A （example/hexadecimal）
When module receives correct command, it will make corresponding actions and send response back to the master. This is
successful communication.
5.4 、Command for state collection of digital output：
Send: 01 01 00 00 00 08 3D CC （example/hexadecimal）
data byte data description remark
01 1 module address address range 01-FE
01 1 function code 01-read coil status
0000 2 coil address(0x mode) 0000-initial address of coil
0008 2 read coil length 0008-read 8 coil status
3DCC 2 check code CRC check code for all data
Receive: 01 01 01 A4 50 33 （example/hexadecimal）
data byte data description remark
01 1 module address address range 01-FE
01 1 function code 01-read coil status
01 1 byte number 01-read one byte length
A4 1 read data A4-read coil status
WP8025ADAM User’s Manual V1.42
5033 2 check code CRC check code for all data
Converting input data “A4 ” ”
to 2 hexadecimal results “10100100 . From left to right, it represent the 8 relay output status
、
RY8-RY1,here it means RY8 RY6 and RY3 has output but others no.
5.5 、command for module address setting：
Send：00 06 00 64 00 01 08 04 （example/hexadecimal）
date byte data description remark
00 1 module address 00-group sending
06 1 function code 06-write single register
0064 2 register address (4x mode) 0064-modify module address
0001 2 data writing set new address for module, range 0001-00FE
0804 2 CRC check code CRC check code for all data
：
Receive 00 06 00 64 00 01 08 04 （example/hexadecimal）
This command means to send a code to a module, set the module address as 01, this setting could be saved when power off;
default address of module is 01,each module address could be assigned separately when using multiple modules for
network.Attentions is required that only one module could be used in 485 network when using multiple address sending,
otherwise all the modules will share the same address in 485 network. When module receives correct command, it will make
corresponding actions and send response back to the master. This is successful communication.
5.6 、Command for communication parameter setting：
Send：01 06 00 65 00 02 18 14 （example/hexadecimal）
data byte data description remark
01 1 module address address range:01-FE
06 1 function code 06-write single register
0065 2 register address (4x mode) 0065-modify communication parameter
0002 2 data writing 0001-set communication parameter 4800,N(no
check) ,8,1
0002-set communication parameter 9600,N(no
check) ,8,1
0003-set communication parameter 19200,N(no
check) ,8,1
0004-set communication parameter 38400,N(no
check) ,8,1
0005-set communication parameter 4800,E(even
check) ,8,1
0006-set communication parameter 9600,E(even
check) ,8,1
0007-set communication parameter 19200,E(even
check) ,8,1
0008-set communication parameter 38400,E(even
check) ,8,1
1814 2 CRC check code CRC check code for all data
：
Receive 01 06 00 65 00 02 18 14 （example/hexadecimal）
This command means to send a code to the module and set the communication parameter as “9600, N (No check), 8, 1”.This
setting could be saved when power off. The default communication parameter is “9600, N (no check), 8, 1”. Attention is
required, when electing the correct communication parameter in communication setting and restarting the communication
terminal, setting will be done.Normally, the lower of baud rate, the lower of the transaction speed but the higher of transaction
stability. The opposite is also true.When module receives correct command, corresponding action will be taken and response
will be sent back to the master. This is successful communication.
6 、Indicator LED description
When module powered on, Led is green.
When module is under communication, LED is twinkling.
when module receive correct command, LED is green.
when module receive incorrect command or command for other modules, LED is red.
、
7 PC debugging instruction
This module provides software for parameter setting and function test. Please follow the steps below:
Connect the module and computer using RS485 converter.
WP8025ADAM User’s Manual V1.42
Connect 12V or 24V power with module and power on. To avoid any unnecessary damage, please make sure the power
positive & negative terminals are correctly connected before power on.
Open the software, select the correct module number, you will see the window of function test or parameter setting.
Set correct parameter, open communication interface.
Select corresponding setting, collection and control items.
8 、RS485 network diagram
https://www.wy-international.com/
https://www.ebay.com/str/tiamofaye/
Email: [email protected]
