4/2 and 4/3 Directional Control Valve, Solenoid Operated, Wire Box
RPEW4-10 Size 10 (D05) Qmax 140 l/min (37 GPM) pmax 350 bar (5100 PSI)
Technical Features
›› Direct acting directional control valve with subplate mounting surface acc. to ISO 4401,
DIN 24340 (CETOP 05)
›› High transmitted hydraulic power up to 350 bar with optimized design to minimize pressure drop
›› Five chamber housing design with reduced hydraulic power dependence on fluid viscosity
›› Wire box for solenoid electrical connection with cable gland [1/2” NPT]
›› Optional 3-pin or 5-pin connector acc. to ANSI/B93.55M
›› Type for AC power supply with a rectifier bridge built in the wire box
›› Wide range of interchangeable spools and manual overrides available
›› CSA Certificate upon request
›› Soft-shift spool speed control option
›› Optional shift position indicators (raised arrows) installed on the terminal plate
›› In the standard version, the valve housing is phosphated and steel parts zinc-coated
for 240 h salt spray protection acc. to ISO 9227
ISO 4401-05-04-0-05 Technical Data
46(1.81)
Valve size 10 (D05)
Max. flow l/min (GPM) 140 (37)
Max. operating pressure at ports P, A, B bar (PSI) 350 (5080)
B TB
Max. operating pressure at port T bar (PSI) 210 (3050)
4xM
Fluid temperature range (NBR) °C (°F) -30 ... +80 (-22 ... +176)
54(2.13)
50,8(2)
6-
Fluid temperature range (FPM) °C (°F) -20 ... +80 (-4 ... +176)
6H
37,3(1.47)
x15
Ambient temperature range °C (°F) -30 … +50 (-22 … +122)
P
+1
27(1.06)
16,7(0.66)
Supply voltage tolerance % AC: ±10 DC: ±10
/18
A TA
-2
Max. switching frequency 1/h 15 000
Enclosure type acc.to EN 60529 IP65
13,5(0.53)
3,2(0.13)
ON ms AC: 50 ... 330 DC: 50 ... 120
24,6(0.97) Switching time at ν=32 mm2/s (156 SUS)
OFF ms AC: 100 ... 300 DC: 30 ... 90
39,7(1.56)
Weight - valve with 1 solenoid 3.9 (8.6)
kg (lbs)
- valve with 2 solenoids 5.4 (11.9)
Ports P, A, B, T - max ∅11.2 mm (0.44 in) Datasheet Type
General information GI_0060 Products and operating conditions
Coil types C_8007 C31K*
Mounting interface SMT_0019 Size 10
Spare parts SP_8010
Characteristics measured at ν = 32 mm2/s (156 SUS)
Operating limits Pressure drop related to flow rate
Operating limits for maximum hydraulic power at rated temperature and supply
voltage equal to 90% nominal.
350 1,2,3, (5076) 22
Operating pressure p [bar (PSI)]
Pressure drop Δp [bar (PSI)]
(5076) 1 20
(4351) 300 4,5,6, 6 (4351) 6
18
7,8,9 5 2
(3626) 250 (3626) 16
14 5
(2901) 3 (2901) 4
200 4 12
7
(2176) (2176) 10
150 3 2
9 8
8 (1450) 1
(1450) 100 6
(725) 4
(725) 50 1,2,3,5, 2
9 4 6,7,8
0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140
(5.3) (10.6) (15.9) (21.1) (26.4) (31.7)(37.0) (5.3) (10.6) (15.9) (21.1) (26.4) (31.7)(37.0)
Flow Q [l/min (GPM)] Flow Q [l/min (GPM)]
P-A P-B A-T B-T P-T P-A P-B A-T B-T P-T
1 Z11 5 Y51 7 L21 Z11,P11,Y11,
1 1 2 2 C11 4 3 4 5 1
1 Z51 3 C11 2 R21 R11,X11,B11
1 H11 3 C51 6 J15 Z51,P51,Y51,
1 2 C21 6 6 6 6 4
B51
1 H51 2 R11 6 J75
R21 1 1 1 3 C51 4 5 1
1 P11 2 X11 8 A51 J15 1 2 2 3 L21 1 1 1 2 2
1 P51 4 B11 9 C21 J75,A51 1 1 H11 1 1 2 2 1
5 Y11 4 B51 H51 1 2 1
For operating limits under conditions and flow directions other than shown contact our technical support. Admissible operating limits may be
considerably lower with only one direction of flow (A or B plugged, or without flow.)
Page 1 www.argo-hytos.com
Subject to change · RPEW4-10_4044_2en_05/2018
Ordering Code
RPEW4 - 10 / -
4/2 and 4/3
directional control valve,
solenoid operated, wire box
CSA Certifed
Valve size No designation standard
U CSA marking
Number of valve positions
two positions 2
three positions 3 Surface treatment
No designation standard
Spool symbols
see the table “Spool Symbols“
Rated supply voltage of solenoid Seals
(at the wire box terminal) No designation NBR
12 V DC / 3.17 A 01200 V FPM (Viton)
24 V DC / 1.73 A 02400
120 V AC / 0.38 A, 60 Hz* 12060
*DC coils with rectifier in wire box
Soft-shift spool speed control
No designation without soft-shift control
Connector for wire box and wire box power T0 with plugged cavity for optional soft shift installation
T2 orifice Ø 0.6 mm (0.02 inch) in T line bridge
DC solenoid for DC power supply EW1K T3 adjustable needle valve in T line bridge
DC solenoid for AC power supply (rectifier in wirebox) EW1R
Wire box version
without connector, 1/2 NPT thread at both ends (either side 50 Manual override
can be used for wiring, remove cover-plug accordingly) No designation standard
50 with LED (B side plugged, A side with feed-through plug) 51 N2 rubber boot protected
- For directional valves with two solenoids, one solenoid must be de-energized before the other solenoid can be charged.
- The port restrictor plugs can be ordered separately from the spare parts data sheet SP_8010.
- Mounting bolts M6 x 45 DIN 912-10.9 or studs must be ordered separately. Tightening torque is 14 Nm (10.3 Ibf.ft).
- Besides the shown, commonly used valve versions other special models are available. Contact our technical support
for their identification, feasibility and operating limits.
Spool Symbols
Type Symbol Interposition Type Symbol Interposition
Z11 P51
C11 Y51
H11 C51
P11 B51
Y11 Z51
L21 H51
B11 X11
C21 C11
R11 H11
R21 J15
A51 J75
www.argo-hytos.com Page 2
Subject to change · RPEW4-10_4044_2en_05/2018
Solenoid Coil for Wire box in millimeters (inches)
45,5 (1.79)
62 (2.48)
31 (1.22)
72 (2.83)
73,2 (2.88)
Manual Override in millimeters (inches)
No designation Designation N2
- standard - rubber boot protected
106 (4.17)
123,5 (4.86)
In case of solenoid malfunction or power failure, the spool of the valve can be shifted by manual override as long as the pressure in port T
does not exceed 25 bar (363 PSI). For alternative manual overrides contact our technical support.
Spool Speed Control in millimeters (inches)
Designation T0 - Plug VSTI M10 x 1 Designation T2 - Orifice ∅ 0.6 (0.02) Designation T3 - Needle valve
The orifice extends the valve The needle valve allows continuous
Switching shifting time. adjustment of the shifting time.
Plugged cavity for optional soft-shift control time
devices installation (T2, T3) ON and OFF 120 ... 350 ms 30 ... 2000 ms
The switching times shown are valid for viscosity ν = 32 mm2/s (156 SUS) and nominal voltage.
They depend on working pressure and flow rate of the directional control valve.
Example - connecting of connectors ANSI / B93.55M
Pinout - 3-pin connector Pinout - 5-pin connector
1 - white Ground
1 - green 3
2 - black 3 2 2 - red
3 - white 3 - green 2 4
4 - orange
5 - black 1 5
Ground 1
solenoid „a“ or „b“ solenoid „a“
3
3 2 2 4
1 5
1
solenoid „b“
Page 3 www.argo-hytos.com
Subject to change · RPEW4-10_4044_2en_05/2018
Dimensions in millimeters (inches)
Valve with two solenoids
RPEW4-103*/*EW1*
Valve with one solenoid „a“
Spool symbols R11, R21, Y51, C51, Z51, H51
RPEW4-102*/*EW1*
Plastic nut
6+1 Nm (4.3+0.7 lbf.ft)
Valve with one solenoid „b“
Spool symbols C11, H11
RPEW4-102*/*EW1*
Plastic nut
6+1 Nm (4.3+0.7 lbf.ft)
Mounting screws 14 Nm (10.3 lbf.ft)
M6 x 45 DIN 912-10.9
www.argo-hytos.com Page 4
Subject to change · RPEW4-10_4044_2en_05/2018
