01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

🔍 Search 📰 V

Compressive Strength of Concrete -Cube Test [PDF], Proce

Results
⌂ Home / Concrete Technology

The compressive strength of the concrete cube test provides an idea about all the characteristics of concrete. By this single test
judge that whether Concreting has been done properly or not. Concrete compressive strength for general construction varies fro
MPa (2200 psi) to 30 MPa (4400 psi) and higher in commercial and industrial structures.

Compressive strength of concrete depends on many factors such as water-cement ratio, cement strength, quality of concrete ma
quality control during the production of concrete, etc.

Test for compressive strength is carried out either on a cube or cylinder. Various standard codes recommend a concrete cylinder
concrete cube as the standard specimen for the test. American Society for Testing Materials ASTM C39/C39M provides Standard
Method for Compressive Strength of Cylindrical Concrete Specimens.

Compressive Strength De nition


Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 1/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

Compressive strength is the ability of material or structure to carry the loads on its surface without any crack or de ection. A ma
under compression tends to reduce the size, while in tension, size elongates.

Compressive Strength Formula

Compressive strength formula for any material is the load applied at the point of failure to the cross-section area of the face on w
load was applied.

Compressive Strength = Load / Cross-sectional Area

Procedure: Compressive Strength Test of Concrete Cubes

For cube test two types of specimens either cubes of 15cm X 15cm X 15cm or 10cm X 10cm x 10cm depending upon the size of ag
are used. For most of the works cubical molds of size 15cm x 15cm x 15cm are commonly used.

This concrete is poured in the mold and appropriately tempered so as not to have any voids. After 24 hours, molds are removed,
test specimens are put in water for curing. The top surface of these specimen should be made even and smooth. This is done by
cement paste and spreading smoothly on the whole area of the specimen.


Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 2/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

These specimens are tested by compression testing machine after seven days curing or 28 days curing. Load should be applied
gradually at the rate of 140 kg/cm2 per minute till the Specimens fails. Load at the failure divided by area of specimen gives the
compressive strength of concrete.

Following are the procedure for testing the Compressive strength  of Concrete Cubes
Apparatus for Concrete Cube Test
Compression testing machine

Preparation of Concrete Cube Specimen

The proportion and material for making these test specimens are from the same concrete used in the eld.

Specimen

6 cubes of 15 cm size Mix. M15 or above 

Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 3/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

Mixing of Concrete for Cube Test

Mix the concrete either by hand or in a laboratory batch mixer

Hand Mixing

1. Mix the cement and ne aggregate on a watertight none-absorbent platform until the mixture is thoroughly blended and is of uniform color.
2. Add the coarse aggregate and mix with cement and ne aggregate until the coarse aggregate is uniformly distributed throughout the batch.
3. Add water and mix it until the concrete appears to be homogeneous and of the desired consistency.
Sampling of Cubes for Test
1. Clean the mounds and apply oil.
2. Fill the concrete in the molds in layers approximately 5 cm thick.
3. Compact each layer with not less than 35 strokes per layer using a tamping rod (steel bar 16mm diameter and 60cm long, bullet-pointed at lo
end).
4. Level the top surface and smoothen it with a trowel.
Curing of Cubes
The test specimens are stored in moist air for 24 hours and after this period the specimens are marked and removed from the m
and kept submerged in clear freshwater until taken out prior to the test.

Precautions for Tests

The water for curing should be tested every 7 days and the temperature of the water must be at 27+-2oC.

Procedure for Concrete Cube Test

1. Remove the specimen from the water after speci ed curing time and wipe out excess water from the surface.
2. Take the dimension of the specimen to the nearest 0.2m
3. Clean the bearing surface of the testing machine
4. Place the specimen in the machine in such a manner that the load shall be applied to the opposite sides of the cube cast.
5. Align the specimen centrally on the base plate of the machine.
6. Rotate the movable portion gently by hand so that it touches the top surface of the specimen.
7. Apply the load gradually without shock and continuously at the rate of 140 kg/cm2/minute till the specimen fails
8. Record the maximum load and note any unusual features in the type of failure.
Note:

Minimum three specimens should be tested at each selected age. If the strength of any specimen varies by more than 15 percent
average strength, the results of such specimens should be rejected. The average of three specimens gives the crushing strength o
concrete. The strength requirements of concrete.

Calculations of Compressive Strength Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 4/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

Size of the cube =15cmx15cmx15cm

Area of the specimen (calculated from the mean size of the specimen )=225 cm2

Characteristic compressive strength(f ck)at 7 days =

Expected maximum load =fck x area x f.s

Range to be selected is …………………..

Similar calculation should be done for 28 day compressive strength

Maximum load applied =……….tones = ………….N

Compressive strength = (Load in N/ Area in mm2)=……………N/mm2

=……………………….N/mm2

Reports of Cube Test

1. Identi cation mark
2. Date of test
3. Age of specimen
4. Curing conditions, including date of manufacture of specimen
5. Appearance of fractured faces of concrete and the type of fracture if they are unusual
Results of Concrete Cube Test
Average compressive strength of the concrete cube = ………….N/ mm2 (at 7 days)

Average compressive strength of the concrete cube =………. N/mm2 (at 28 days)

Compressive Strength of Concrete at Various Ages

The strength of concrete increases with age. The table shows the strength of concrete at di erent ages in comparison with the st
at 28 days after casting.

Age Strength percent

1 day 16%

3 days 40%

7 days 65%

14 days 90%

28 days 99%

Compressive Strength of Di erent Grades of Concrete at 7 and 28 Days

Grade of Concrete Minimum compressive strength N/mm2 at 7 days Speci ed characteristic compressive strength (N/mm2) at 28 da

M15 10 15

M20 13.5 20

M25 17 25

Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 5/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

M30 20 30

M35 23.5 35

M40 27 40

M45 30 45

Some Facts on Concrete Strength Test

Why Compressive Strength Test of Concrete is Important?
The compressive strength of the concrete cube test provides an idea about all the characteristics of concrete. By this single test o
judge that whether Concreting has been done properly or not.

What is compressive strength of commonly used concrete?

Concrete compressive strength for general construction varies from 15 MPa (2200 psi) to 30 MPa (4400 psi) and higher in comm
and industrial structures.

What is compressive strength after 7 days and 14 days?

Compressive strength achieved by concrete at 7 days is about 65% and at 14 days is about 90% of the target strength.

Which test is most suitable for concrete strength?

A concrete cube test or concrete cylinder test is generally carried out to assess the strength of concrete after 7 days, 14 days or 28
of casting.

What is the size of concrete cubes used for testing?

For cube test two types of specimens either cubes of 15cm X 15cm X 15cm or 10cm X 10cm x 10cm depending upon the size of ag
are used. For most of the works cubical molds of size 15cm x 15cm x 15cm are commonly used.

Which machine is used for concrete strength test?

The compression testing machine is used for testing the compressive strength of concrete.

What is the rate of loading on compression testing machine?

Load should be applied gradually at the rate of 140 kg/cm2 per minute till the Specimens fails.

Which ACI Code is use for Concrete Strength Test?

American Society for Testing Materials ASTM C39/C39M provides Standard Test Method for Compressive Strength of Cylindrica
Concrete Specimens.
Read More:

1. Concrete – De nition, Grades, Components, Manufacture, Construction

2. Why do We Test Concrete Compressive Strength after 28 Days?

 Share This Article  Facebook   


Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 6/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

← Previous article
Methods for Production of High-Strength Concrete [PDF]

Next ar
Types of Foundation for Buildings and their U

Gopal Mishra ✓

Related Posts

How to Carry out Concrete Cubes Sampling as per IS ... How to Test Quality of Steel Reinforcement at Constructio


Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 7/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

📖 Popular Articles

Types of Foundation for Buildings and their Uses [PDF]

Methods of Rainwater Harvesting [PDF]: Components, Transport, and Storage

Compressive Strength of Concrete -Cube Test [PDF], Procedure, Results

Standard Size of Rooms in Residential Building and their Locations

Calculate Quantities of Materials for Concrete -Cement, Sand, Aggregates

📖 Recent Articles

How to Carry out Concrete Cubes Sampling as per IS 456?

How to Test Quality of Steel Reinforcement at Construction Site?

How to Design One-way Slab as per ACI 318-19? | Example Included

A Unique Technique to Strengthen 3D Printed Concrete | Video Inside

Woodworking Starter Kit: Essentials That Every Beginner Should Have

📖 Recent Questions

Why is the risk of e orescence formation in cement-based materials high in coastal areas?
 1 Answer

What is the percentage of carbon in wrought iron?

 2 Answers

Which country provides highest salary to civil engineers?

 1 Answer

What are the important points of FIDIC Contract we should keep in mind during tendering?
 0 Answers

What is the di erence between Airport, Aerodrome and Air eld?

 0 Answers


Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 8/9
01/02/2021 Compressive Strength of Concrete -Cube Test, Procedure, Results

📁 Know More

⌂ Home
 About Us
 Contact Us
 Privacy Policy
 Terms & Conditions

📁 Connect With Us

 Ask Question

✎ Write Article

 VIP Membership
 Popular Questions

Search ...

Articles

Search

© 2009-2020 The Constructor. All Rights Reserved.


Get Noti cations ×
https://theconstructor.org/concrete/compressive-strength-concrete-cube-test/1561/#:~:text=These specimens are tested by,the compressive stren… 9/9