ORDER NO.

CRT3171
DEH-P460MP/XM/UC

MULTI-CD CONTROL HIGH POWER CD/MP3/WMA PLAYER WITH FM/AM TUNER

DEH-P460MP /XM/UC

DEH-P4600MP/XM/UC
DEH-P4650MP/XM/ES
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks

CX-3098 CRT3179 S10WMAcode2 CD Mech. Module:Circuit Description, Mech. Description, Disassembly

For details, refer to "Important symbols for good services".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2003
K-ZZW. NOV. 2003 printed in Japan
 1 2 3 4

SAFETY INFORMATION
CAUTION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the
warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk
trying to do so and refer the repair to a qualified service technician.

WARNING

This product contains lead in solder and certain electrical parts contain chemicals which are known to the
state of California to cause cancer, birth defects or other reproductive harm.
B
Health & Safety Code Section 25249.6 - Proposition 65

- CD Player Service Precautions

1. Before disassembling the unit, be sure to turn off the 3. After replacing the pickup unit, be sure to check
power. Unplugging and plugging the connectors dur- the grating.(See p.52.)
C ing power-on mode may damage the ICs inside the
unit.
2. To protect the pickup unit from electrostatic dis-
charge during serviving, take an appropriate treat-
ment(shorting-solder) by referring to "the DISAS-
SEMBLY" on page 56.

2 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

[ Important symbols for good services ]

In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them: A
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.

2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.

3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, B
proper cleaning should be performed to restore their performances.

4. Shipping mode and shipping screws

To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.

5. Lubricants, glues, and replacement parts

Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
C

DEH-P460MP/XM/UC 3
5 6 7 8
 1 2 3 4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
A 2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 8
2.1 PACKING ................................................................................................................................................... 8
2.2 EXTERIOR............................................................................................................................................... 10
2.3 CD MECHANISM MODULE..................................................................................................................... 14
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 16
3.1 BLOCK DIAGRAM ................................................................................................................................... 16
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 18
3.3 KEYBOARD UNIT.................................................................................................................................... 24
3.4 CD MECHANISM MODULE(GUIDE PAGE) ............................................................................................ 26
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 36
4.1 TUNER AMP UNIT................................................................................................................................... 36
4.2 PANEL UNIT ............................................................................................................................................ 40
B
4.3 KEYBOARD UNIT.................................................................................................................................... 41
4.4 CD CORE UNIT(S10WMA)...................................................................................................................... 42
5. ELECTRICAL PARTS LIST ............................................................................................................................ 44
6. ADJUSTMENT ............................................................................................................................................... 50
6.1 CD ADJUSTMENT................................................................................................................................... 50
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 52
6.3 ERROR MODE ........................................................................................................................................ 54
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 55
7. GENERAL INFORMATION ............................................................................................................................. 56
7.1 DIAGNOSIS ............................................................................................................................................. 56
7.1.1 DISASSEMBLY ..................................................................................................................................... 56
C 7.1.2 CONNECTOR FUNCTION DESCRIPTION .......................................................................................... 59
7.2 PARTS...................................................................................................................................................... 60
7.2.1 IC .......................................................................................................................................................... 60
7.2.2 DISPLAY ............................................................................................................................................... 69
7.3 OPERATIONAL FLOW CHART ............................................................................................................... 71
7.4 CLEANING............................................................................................................................................... 72
8. OPERATIONS ................................................................................................................................................ 73

4 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

1. SPECIFICATIONS
A

DEH-P460MP/XM/UC 5
5 6 7 8
 1 2 3 4

6 DEH-P460MP/XM/UC
1 2 3 4
5 6 7 8

DEH-P460MP/XM/UC 7
5 6 7 8
 1 2 3 4

2. EXPLODED VIEWS AND PARTS LIST

NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• Screw adjacent to mark on the product are used for disassembly.
"
A
• For the applying amount of lobricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
2.1 PACKING

(1) PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Cord Assy CDE7060

2 Accessory Assy See Contrast table(2) * 16 Battery CEX1065
E 3 Spring CBH1650 17 Carton See Contrast table(2)
4 Screw Assy See Contrast table(2) 18 Contain Box See Contrast table(2)
5 Fixing Screw See Contrast table(2) 19 Protector CHP2663
20 Protector CHP2664
6 Screw CBA1650
* 7 Polyethylene Bag CEG-127 21-1 Owner's Manual See Contrast table(2)
8 Screw CRZ50P090FTC 21-2 Owner's Manual See Contrast table(2)
9 Screw TRZ50P080FTC 21-3 Installation Manual See Contrast table(2)
* 10 Polyethylene Bag CEG-158 * 21-4 Warranty Card See Contrast table(2)
* 21-5 Card See Contrast table(2)
11 Handle CNC5395
F 12 Holder See Contrast table(2) * 21-6 Caution Card See Contrast table(2)
13 Holder See Contrast table(2) 22 Case Assy See Contrast table(2)
14 Bush CNV3930 23 Remote Control Unit CXC3173
15 Polyethylene Bag See Contrast table(2) 24 Inner Box XHW7001
8 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

(2) CONTRAST TABLE

DEH-P460MP/XM/UC, DEH-P4600MP/XM/UC and DEH-P4650MP/XM/ES are constructed the same
except for the following: A
Parts No.
Mark No. Symbol and Description DEH-P460MP/XM/UC DEH-P4600MP/XM/UC DEH-P4650MP/XM/ES
2 Accessory Assy CEA3376 CEA3376 CEA3439
4 Screw Assy CEA3848 CEA3848 CEA3849
5 Fixing Screw BPZ20P060FZK BPZ20P060FZK Not used
12 Holder CND1249 CND1249 Not used
13 Holder CND1250 CND1250 Not used

15 Polyethylene Bag CEG1173 CEG1173 CEG-162

17 Carton XHG7016 XHG7013 XHG7011
18 Contain Box XHL7016 XHL7013 XHL7011 B
21-1 Owner's Manual XRD7030 XRD7028 XRD7021
21-2 Owner's Manual Not used Not used XRD7022

21-3 Installation Manual XRD7031 XRD7029 XRD7023

* 21-4 Warranty Card CRY1070 Not used Not used
* 21-5 Card Not used ARY1048 Not used
* 21-6 Caution Card Not used CRP1294 Not used
22 Case Assy Not used Not used CXB3520

- Owner's Manual, Installation Manual

C
Model Parts No. Language
DEH-P460MP/XM/UC XRD7030 English, French, Spanish
XRD7031
DEH-P4600MP/XM/UC XRD7028
XRD7029
DEH-P4650MP/XM/ES XRD7021 English, Spanish, Portuguese(B)
XRD7022 Arabic, Traditional Chinese
XRD7023 English, Spanish, Portuguese(B), Arabic, Traditional Chinese

DEH-P460MP/XM/UC 9
5 6 7 8
 1 2 3 4

2.2 EXTERIOR

10 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

(1) EXTERIOR SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.
1 Screw BMZ30P040FZK
51 Fuse(10A) CEK1208 A
2 Screw BSZ26P060FTC
3 Screw BSZ30P060FTC 52 FM/AM Tuner Unit CWE1646
4 Screw BSZ30P200FTC 53 Holder CND1054
5 Terminal(CN402) VNF1084 54 Pin Jack(CN352) See Contrast table(2)
55 Plug(CN981) CKM1376
6 Cord Assy CDE7060
7 Button(EJECT) CAC7752 56 Connector(CN801) See Contrast table(2)
8 Screw(M2x4.5) CBA1647 57 Connector(CN101) CKS3408
9 Screw(M2x4) CBA1649 58 Plug(CN831) CKS3537
10 Washer CBF1038 59 Connector(CN721) CKS3837
60 Antenna Jack(CN401) CKX1056
B
11 Spring CBH2650
12 Spring CBH2651 61 Holder See Contrast table(2)
13 Spring CBH2652 62 Holder CND1352
14 Spring CBH2653 63 Heat Sink CNR1668
15 Holder CND1254 64 Insulator XNM7031
65 Detachable Assy See Contrast table(2)
16 Gear CNV5997
17 Arm CNV7400 66 Screw BPZ20P100FZK
18 Arm CNV7401 67 Spring CBL1470
19 Arm CNV7402 68 Knob See Contrast table(2)
20 Arm CNV7403 69 Button(1-6) XAC7005
C
70 Button(LOUD) XAC7020
21 Panel Unit CWM8758
22 Socket(CN1950) CKS3550 71 Button(PAUSE) XAC7019
23 Connector(CN1951) CKS4806 72 Button(OPEN) See Contrast table(2)
24 Holder Unit CXB9501 73 Spring XBH7001
25 Holder Unit CXB9502 74 Cover XNS7013
75 Keyboard Unit See Contrast table(2)
26 Damper Unit CXB9503
27 Service Panel Unit CXX1691 76 LCD(LCD1901) See Contrast table(2)
28 Spring CBL1512 77 Connector(CN1901) CKS4524
29 Cover CNM6854 78 Sheet XNM7006
D
30 Panel CNS7245 79 Connector XNV7006
80 Holder XNC7002
31 Pin CNV6486
32 Lighting Conductor CNV6487 81 Lighting Conductor XNV7005
33 Case CNB2870 82 Button(BAND) XAC7021
34 Earth Plate CNC8915 83 Button(EQ) XAC7022
35 Cushion CNM8890 84 Sub Grille Assy See Contrast table(2)
85 Sub Button Assy(SELECT) See Contrast table(2)
36 Insulator CNM7682
37 Insulator CNM7935 86 IC(IC301) PAL007A
38 Insulator CNM8174 87 Choke Coil(L981) CTH1280 E
39 Panel See Contrast table(2) 88 Transistor(Q752,901,911) 2SD2375
40 Holder Unit CXB6681 89 Screw See Contrast table(2)
90 Holder See Contrast table(2)
41 Chassis Unit CXB9528
42 Remote Control Unit CXC3173 91 Sheet See Contrast table(2)
43 Cover CNS7068 * 92 Lighting Conductor XNV7012
44 CD Mechanism Module(S10CODE2)CXK5665 93 Button(CLOCK) See Contrast table(2)
45 Screw ISS26P055FTC

46 Cable CDE7189
47 Tuner Amp Unit See Contrast table(2) F
48 Screw ASZ26P060FTC
49 Screw BPZ26P080FTC
50 Screw BSZ26P160FTC
DEH-P460MP/XM/UC 11
5 6 7 8
 1 2 3 4

(2) CONTRAST TABLE

DEH-P460MP/XM/UC, DEH-P4600MP/XM/UC and DEH-P4650MP/XM/ES are constructed the same
A
except for the following:
Parts No.
Mark No. Symbol and Description DEH-P460MP/XM/UC DEH-P4600MP/XM/UC DEH-P4650MP/XM/ES
39 Panel CNS6935 XNS7070 CNS6935
47 Tuner Amp Unit XWM7023 XWM7023 XWM7024
54 Pin Jack(CN352) CKB1051 CKB1051 CKB1057(CN351)
56 Connector(CN801) CKS4124 CKS4124 Not used
61 Holder CND1325 CND1325 CND1237

65 Detachable Assy XXA7132 XXA7133 XXA7134

68 Knob XAA7009 XAA7003 XAA7009
72 Button(OPEN) XAC7026 XAC7012 XAC7026
B
75 Keyboard Unit XWM7031 XWM7031 XWM7032
76 LCD(LCD1901) XAW7004 XAW7004 XAW7002

84 Sub Grille Assy XXA7147 XXA7148 XXA7149

85 Sub Button Assy(SELECT) XXA7229 XXA7228 XXA7229
89 Screw Not used BMZ40P140FTC Not used
90 Holder Not used CNV7619 Not used
91 Sheet Not used Not used XNM7008

93 Button(CLOCK) XAC7016 XAC7024 XAC7016

12 DEH-P460MP/XM/UC
1 2 3 4
5 6 7 8

DEH-P460MP/XM/UC 13
5 6 7 8
 1 2 3 4

2.3 CD MECHANISM MODULE

5
42
A 13 81
5 34
15 22
E
5
13 F

93

13 92
A 26
B 82
44 G

5 13 86 83
C 68
D
B 1 54 52
53 86 28 I H
4
37 28

4 71 45
23 J
1
55 87
4 36 38
4 50
73
1
23
18 29 72
K
2
64 51 10 75
C 47 1
I 76 B 59
2
24 1 49
7
61 E
77 90
M F
2 1 48
63 Q
A 27
1
2 H 8
G J 67
21 L
M
1 N D
57 R O
16 17
79 12
D
58 1
3 78
1 33
2 P 46
62 2 20 60
80
40 6
1 1
N
60
1GEM1024 39
11
1
2GEM1045 1 89
25
69 43 10
3GEM1035 P L
30 70 K
56 19
E 14
74
41
R
31 85

C Q

91 14
D 65 35
1 O
85
31
3 2
F 66

85

14 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

CD MECHANISM MODULE SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.
1 CD Core Unit(S10WMA) CWX2851
51 Gear CNV7208 A
2 Connector(CN101) CKS4182
3 Connector(CN901) CKS4017 52 Gear CNV7209
4 Screw BMZ20P035FTC 53 Gear CNV7210
5 Screw BSZ20P040FTC 54 Gear CNV7211
55 Gear CNV7212
6 Screw(M2x4) CBA1362
7 Screw(M2x3) CBA1511 56 Rack CNV7214
8 Screw(M2x3) CBA1527 57 Arm CNV7215
9 ••••• 58 Arm CNV7216
10 Washer CBF1038 59 Guide CNV7217
60 Roller CNV7218
B
11 Washer CBF1060
12 Spring CBH2390 61 Gear CNV7219
13 Spring CBH2606 62 Arm CNV7221
14 Spring CBH2607 63 Arm CNV7220
15 Spring CBH2608 64 Arm CNV7222
65 Damper CNV7313
16 Spring CBH2609
17 Spring CBH2610 66 Damper CNV7314
18 Spring CBH2735 67 Arm CNV7341
19 Spring CBH2612 68 Arm CNV7342
20 Spring CBH2613 69 Guide CNV7360
C
70 Guide CNV7361
21 Spring CBH2614
22 Spring CBH2615 71 Holder CNV7437
23 Spring CBH2616 72 Arm CNV7805
24 Spring CBH2617 73 Gear CNV7595
25 Spring CBH2620 74 Damper CNV7618
75 Motor Unit(M1) CXB6007
26 Spring CBH2621
27 Spring CBH2641 76 Chassis Unit CXC2318
28 Spring CBH2642 77 Screw Unit CXB8729
29 Spring CBH2643 78 Gear Unit CXC2397
D
30 Spring CBH2659 79 Arm Unit CXC2316
80 Arm CND1896
31 Spring CBH2688
32 ••••• 81 Arm CND1894
33 Shaft CLA4441 82 Motor Unit(M2) CXB8933
34 Frame CNC9962 83 Bracket CNC9985
35 Frame CNC9963 84 •••••
85 Screw(M2x5) EBA1028
36 Bracket CNC9966
37 Bracket CND1895 86 Screw JFZ20P020FTC
38 Arm CNC9968 87 Screw JGZ17P022FTC E
39 Arm CND1909 88 •••••
40 Lever CND2032 89 Washer YE20FTC
90 Pickup Unit(P10)(Service) CXX1641
41 Lever CNC9984
42 Sheet CNM8134 91 Screw IMS26P030FTC
43 Collar CNV7798 92 Spring CBL1635
44 Guide CNV7799 93 Clamper CNV7197
45 Arm CNV7800

46 Rack CNV7199
47 Holder CNV7201 F
48 Holder CNV7202
49 Arm CNV7203
50 Gear CNV7207
DEH-P460MP/XM/UC 15
5 6 7 8
 1 2 3 4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM
A

A TUNER AMP UNIT

VDD

7 6 13 5 10 9 8 14
FM/AM TUNER UNIT

WC
CE2

ROM_VDD

SL

DI
CK
CE1

DO
IC 3 EEPROM IC 5
←
5V 3.3V
B 5.0V

OSC LPF

ANTENNA CN401
AM ANT FMRF
1
1 ATT
2 Rch
24
IC 2
2.5V
FM ANT IC 1
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX
RF adj
ANT adj

T51 CF52
CF51

C
AUDIOGND
OSCGND

IC 4
VDD_3.3
RFGND

DGND

←
3.3V 3.3V 2.5V 2.5V
VCC
NC

2 12 15 22 16 4 17

TUN 3.3V TUN L 3

SYS 8V BUS+L BUS+L 5

BUS-L BUS-L 6

CN101 CD L 4
7
11
5
BUZZER EVST,EVCK,EVDT
1
D CD CORE UNIT(S10WMA) 8

IP-BUS DRIVER 100

BUS- PEE
5 1 TX 86
PICKUP UNIT IC 101
6 HA12240FP 2 RX 85
TX
mute
37

D (P10)(SERVICE) BUS+
8
RX
16
V3R3D X1
IPPW 24 X601
CN101 CN901 IPPW
LASER CN721 15
DIODE LD- 142 31 L-OUT X2
15 15 LD IC 201 LOUT 10 14
Q101
MD
UPD63761GJ MUTE Q601 21
143 SYSPW
5 5 PD
Q603 Q101
RF-AMP,CD DECODER,
AC,BD MP3 and WMA DECODER,
HOLOGRAM BU
UNIT
F,E
DIGITAL SERVO / DATA PROCESSOR SYSTEM CONTROLLER
FO+ FOP 58
FOCUS ACT. 1 1 71 STRKEY2
TO+ TOP ASENBO 75
4 4 STRKEY1
MONITOR TRACKING ACT. 34 35
DIODE TD/FD SD/MD Q102 IC 601(2/2) Q601
LD+
14 14 PE5407A 83
AVREF VD
12 X201
FOP BRST,BRXEN,BSRQ
13
TOP 22
BDATA,BSCK adpw
SPINDLE
CD
MOTOR M DRIVER CD CONTROLLER FLPILM
9
16 8
SOP 22 53
15 LOEJ LOEJ ejectin
SOM
18 9
LOAD/ CARRIAGE LCOP CONT 47 55
MOTOR M 17
LCOM
CONT CDMUTE
swvdd
ILMPW
dsens

Q
KYDT

DPDT

E IC 301 IC 701 BRST,BRXEN,BSRQ

BA5835FM PE5402A BU
BDATA,BSCK
Q752 95 90 96 1 20
4 VD
CLAMP VD 3 20 BU
32
12EJ 4 21 VD
31 Q
8EJ
49
30 VDCONT Q
DSCSNS
97 Q751 VDD
HOME

VDCONT
19 5

CLAMP 12EJ 8EJ DISC HOME

SENSE SENSE SENSE SENSE +3.3V REGULATOR
S8
3 2
3VDD IC 703 5 119 VDD
DETACH SENS

V3R3D
3 IC 203 1 VD2 S-812C33AUA-C2N
NJM2391DL1-33
VDD
+3.3V REGULATOR
Q754
VD2
2 22 VD
F V1R5
5 IC 501 1,3
V3R3D
S-L2980A15MC-C6A
1.5V REGULATOR

16 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

UC model only

RESET CN352
1 IC 651 2 FL 2
VDD
BD4834G
Q352

11 RL 6
reset
Q351

CE2 32
tunpce@
CE1 99
TUNPCE
DO 94
TUNPDI
DI
CK
98
TUNPDO CN351 B
97
TUNPCK VDD REGULATOR RL
74 SL 2
Q901
VDD
SYSTEM CONTROLLER Q902
ES model only
IC 601(1/2)
PE5407A 10
DALMON
CN981

BACKUP SENSE BU
93 FUSE
bsens 1 1 BACK UP

BU
10A
Q931
92 ACC
asens 3 3 ACC

ACC SENSE

C
2 2 GND

BU
ELECTRONIC VOLUME/
SOURCE SELECTOR POWER AMP 20
TUN L 3 IN2-L
23
BUS+L 5 FL- 10 10 FL-
IN4+L 21
BUS-L 6 IC 131 10 14 IC 301 FL+ 12 12 FL+
IN4-L FL FLIN 3
PML003AM 12
PAL007A RL- 9 9 RL-
11
RL RLIN 5
CD L 4 IN3-L RL+ 11 11 RL+
MUTE STBY B.REMOTE
22 4 25
6 6 B.REM

EVST,EVCK,EVDT
MUTE
Q502
BU SYS 8V REGULATOR
Q911 Q912
SYS 8V BU
MUTE
Q301
37
ute

X1
16
Q913
D
X601
15
X2

21 SYSPW
PW
TUNER 3.3V REGULATOR
IC 921
R 3 1 UC model only
TUN 3.3V SYS 8V
58
EY2
75 CN801
EY1 NJM2391DL1-33 KEYD 3
Q601 KEYAD 2
83 CN831
REF VDD
1
BU 5 5
22
dpw Q831
6 6
9
LM

tin
8

DGND
8 8
S1970
B PANEL UNIT C KEYBOARD UNIT
9 9
EJECT CN1901
Q961

BU
ILB
7 7 4 9
ILB E
BL+B
10 10 5 8

Q962
Q971
SWDVDD SWVDD
VDD 2 2 2 11

REMOTE CONTROL SENSOR

3
DPDT DPDT OPT IN IC 1902
11 11 10 3 RS-140 1

S831 17 55 11
RFM

VLCD
VDD

KEY DATA KEY MATRIX

DETACH SENSE
18
DPDT LCD DRIVER/
KYDT KYDT KEY CONTROLLER
14 14 8 5
20 IC 1901
KTDT PD6340A LCD

F
CN1951
CN1950

DEH-P460MP/XM/UC 17
5 6 7 8
 1 2 3 4

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)

Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
A "ELECTRICAL PARTS LIST".
A-a

IP-BUS : 2.2dBs

CD : 0.0dBs

C D CN901

FM(100%) : -19.5dBs
AM(30%) : -30dBs

SYSTEM CONTROLLER
FM/AM TUNER UNIT

DETACH
SENSE

EJECT
CN1901

NOTE :
Large size Symbol indicates a resistor.
SCH diagram No differentiation is made between chip resistors and
C

A-a A-b
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:
A-a A-b Guide page
Ex. *Resistors *Capacitors
Code
123
103
Practical value
12k ohms
10k ohms
Code
103
Practical value
0.01uF B PANEL UNIT
101/10 100uF/10V
F A-a A-b Detailed page
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of

A B
identical designation.

18 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

A-b
A TUNER AMP UNIT
FM : 4.8dBs
AM : -5.7dBs
CD : 9.3dBs
IP-BUS : 9.5dBs

FRONT
OUTPUT

FM : 5.6dBs
AM : -4.9dBs B
CD : 10.1dBs
IP-BUS : 10.3dBs

REAR
OUTPUT

3A >
REAR
OUTPUT

CEK1208
LLER 10A

600µH >

FM : 31.6dBs
AM : 21.1dBs
CD : 36.1dBs
IP-BUS : 36.3dBs

DETACH
SENSE

: UC model only

: ES model only

WIRED
REMOTE
CONTROL

A
DEH-P460MP/XM/UC 19
5 6 7 8
 F
E
B
A

D
C

20
A-a A-b

A-a
A-b

1
1

IP-BUS : 2.2dBs

2
2

DEH-P460MP/XM/UC
3
3

CD : 0.0dBs

D CN901
3

4
4

FM(100%) : -19.5dBs
AM(30%) : -30dBs

SYSTEM CONTROLLER
 SYSTEM CONTROLLER
5

5
FM/AM TUNER UNIT

6
6

DETACH
SENSE

DEH-P460MP/XM/UC
EJECT

7
7

NOTE :
Symbol indicates a resistor.
CN1901

No differentiation is made between chip resistors and

discrete resistors.
C

Symbol indicates a capacitor.

No differentiation is made between chip capacitors and
discrete capacitors.
For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:

Ex. *Resistors *Capacitors

Code Practical value Code Practical value
123 12k ohms 103 0.01uF B PANEL UNIT
103 10k ohms 101/10 100uF/10V
8

8
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation. A-a A-b

A-a B
A-b

21
E
A

D
C

F
B
 F
E
B
A

D
C

22
A-a A-b

A-b
A TUNER AMP UNIT

1
1

FM : 4.8dBs
AM : -5.7dBs
CD : 9.3dBs
IP-BUS : 9.5dBs

1
FRONT
OUTPUT

FM : 5.6dBs
AM : -4.9dBs
CD : 10.1dBs

2
2

IP-BUS : 10.3dBs

REAR
OUTPUT

2
3A >
REAR
OUTPUT

DEH-P460MP/XM/UC
3
3

4
4

CEK1208
10A

600µH >
 CEK1208
10A

600µH >
5

5
FM : 31.6dBs
AM : 21.1dBs
CD : 36.1dBs

6
6

IP-BUS : 36.3dBs

4
DETACH
SENSE

DEH-P460MP/XM/UC
7
7

: UC model only

: ES model only

WIRED
REMOTE
CONTROL
8

8
A-a A-b

A-b
23
E
A

D
C

F
B
 1 2 3 4

3.3 KEYBOARD UNIT

*B

*B

D
*D

*B

*C
SRC-OFF

*A *B *C *D
DEH-P460MP/XM/UC CL-195PG-CD CSG1107 CSG1112 XAW7004
DEH-P4600MP/XM/UC CL-195PG-CD CSG1107 CSG1112 XAW7004
DEH-P4650MP/XM/ES CL-195PG-CD CSG1107 CSG1112 XAW7002
F

C
24 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

C KEYBOARD UNIT

CN1951
B

B
VOLUME

*A

*B *C
SCRL
C

*B *B *B *B
*A

*A
*A

*A
*A

*C
*B *B
*C
*A

*A
D

*B *B *B *B

*B *B *B
*C
SRC-OFF

C
DEH-P460MP/XM/UC 25
5 6 7 8
 1 2 3 4

3.4 CD MECHANISM MODULE(GUIDE PAGE)

D-a

C
S

F
C
S

F
L209

B C217

R1

PICKUP UNIT(P10)(SERVICE)

F F

F F

F F
T T
T T
T T
T T

F F

T T

C F
T T
F
#
F F
@

Pull-down

2 $
S
T T

1 9 7
C
F F
8 4
E M1
CXB6007
SPINDLE MOTOR 0 5
S S

S S
F
F
C T
C
T
C
C
M2
CXB8933
LOADING/CARRIAGE
CD DRIVER
S

C
C
S

MOTOR

3.3 REGULATOR

D
26 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

D-b
D CD CORE UNIT(S10WMA)

SWITCHES:
! CD CORE UNIT(S10WMA)
S901 : HOME SWITCH.........ON-OFF
S902 : CLAMP SWITCH.......ON-OFF
S903 : DSCSNS SWITCH.....ON-OFF
S904 : 12EJ SWITCH............ON-OFF
S905 : 8EJ SWITCH..............ON-OFF
1.5 REGULATOR The underlined indicates the switch position.
C
SIGNAL LINE
F FOCUS SERVO LINE
T TRACKING SERVO LINE
C CARRIAGE SERVO LINE
S SPINDLE SERVO LINE
16.934MHz

Pull-down

MICRO COMPUTER

6
R22
C906

E
^
3.3 REGULATOR

A
R01

CN721
C722
1

470P

&
C910

2R2

D
DEH-P460MP/XM/UC 27
5 6 7 8
 F
E
B
A

D
C

28
D-a
A-a D-b

D-a
D-b

1
1

C
F

S
C

S
T
F
1

L209

C217

2
2

R1

PICKUP UNIT(P10)(SERVICE)

DEH-P460MP/XM/UC
F F

F F

F F

3
3

T T
T T
T T
T T

F F

T T
T T
F F
#
F F
@

4
4

2
 2
5

5
Pull-down

6
6

3
3

2 $
S
T T

1 9 7
C
F F
8 4
M1
CXB6007 5
SPINDLE MOTOR 0
S S
4

S S
F

DEH-P460MP/XM/UC
F
C T
C
T
C
C

7
7

M2
CXB8933
LOADING/CARRIAGE
S
S
C
C

MOTOR CD DRIVER

3.3 REGULATOR
5
8

8
D-a
A-a D-b

D-a
D-b

29
E
A

D
C

F
B
 F
E
B
A

D
C

30
D-a D-b

D-b
1
1

D CD CORE UNIT(S10WMA)

2
2

DEH-P460MP/XM/UC
SWITCHES:
! CD CORE UNIT(S10WMA)

3
3

S901 : HOME SWITCH.........ON-OFF

S902 : CLAMP SWITCH.......ON-OFF
S903 : DSCSNS SWITCH.....ON-OFF
S904 : 12EJ SWITCH............ON-OFF
S905 : 8EJ SWITCH..............ON-OFF
1.5 REGULATOR The underlined indicates the switch position.

SIGNAL LINE
F FOCUS SERVO LINE
T TRACKING SERVO LINE
C CARRIAGE SERVO LINE
S

4
SPINDLE SERVO LINE
4

16.934MHz

2
 2
5

5
Pull-down

6
6

MICRO COMPUTER

3
6
R22
C906

^
3.3 REGULATOR

4
DEH-P460MP/XM/UC
7
7

A
R01

CN721

C722
1
470P

&

5
C910
2R2
8

8
D-a D-b

D-b
31
E
A

D
C

F
B
 1 2 3 4

- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65V)
A
1 DSCSNS 5V/div 500ms/div 1 DSCSNS 5V/div 500ms/div 1 DSCSNS 5V/div 500ms/div
2 8SNS 5V/div 5 CLCONT 5V/div 2 8SNS 5V/div
3 12SNS 5V/div 4 LOEJ 5V/div 3 12SNS 5V/div
4 LOEJ 5V/div 6 VD 10V/div 4 LOEJ 5V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation

Ref.: Ref.: Ref.:

GND GND GND

Mode: Mode: Mode:

B Normal Normal Normal

7 SIN 1V/div 2s/div 7 SIN 1V/div 1s/div 7 SIN 1V/div 2s/div

8 CIN 500mV/div 8 CIN 500mV/div 8 CIN 500mV/div
9 TIN 500mV/div 9 TIN 500mV/div 9 TIN 500mV/div

12 cm CD-DA setup operation after loading 12 cm CD-ROM(1 session) setup operation 12 cm CD-ROM(3 sessions) setup operation
after loading after loading

Ref.: Ref.: Ref.:

C REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

0 FIN 200mV/div 500ms/div @ TE 500mV/div 200ms/div # FE 500mV/div 20ms/div

! RFOK 2V/div # FE 500mV/div 0 FIN 500mV/div
7 SIN 2V/div @ TE 500mV/div
9 TIN 500mV/div
12 cm CD-DA Source On setup operation Source On setup operation CD-DA Play operation
D

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

# FE 500mV/div 20ms/div $ MDX 1V/div 50ms/div $ MDX 2V/div 5µs/div

0 FIN 500mV/div 7 SIN 200mV/div 7 SIN 1V/div
E @ TE 500mV/div
9 TIN 500mV/div
CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

32 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

A
0 FIN 500mV/div 200ms/div @ TE 500mV/div 2ms/div % RFAGC 1V/div 500µs/div
# FE 500mV/div % RFAGC 500mV/div @ TE 500mV/div
9 TIN 500mV/div

Focus Search waveform Track Open waveform 1 Track Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

TEST TEST TEST B

% RFAGC 1V/div 500µs/div % RFAGC 1V/div 1ms/div % RFAGC 1V/div 2ms/div

@ TE 500mV/div @ TE 500mV/div @ TE 500mV/div
9 TIN 500mV/div 9 TIN 500mV/div 9 TIN 500mV/div

4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO C

Mode: Mode: Mode:

TEST TEST TEST

% RFAGC 1V/div 200ms/div ^ LOUT 1V/div 200µs/div 1 DSCSNS 5V/div 500ms/div

@ TE 1V/div & ROUT 1V/div 2 8SNS 5V/div
8 CIN 500mV/div 3 12SNS 5V/div
7 SIN 2V/div 4 LOEJ 5V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation
D

Ref.: Ref.: Ref.:

REFO AGND GND

Mode: Mode: Mode:

Normal Normal Normal

1 DSCSNS 5V/div 500ms/div 1 DSCSNS 5V/div 500ms/div 7 SIN 1V/div 500ms/div

5 CLCONT 5V/div 2 8SNS 5V/div 8 CIN 500mV/div
4 LOEJ 5V/div 3 12SNS 5V/div 9 TIN 500mV/div E
4 LOEJ 5V/div
12 cm CD Eject operation 8 cm CD Eject operation CD-DA >> CD-ROM mode change(Band key)

Ref.: Ref.: Ref.:

GND GND REFO

Mode: Mode: Mode:

Normal Normal Normal

DEH-P460MP/XM/UC 33
5 6 7 8
 1 2 3 4

A
7 SIN 1V/div 500ms/div % RFAGC 1V/div 500µs/div
8 CIN 500mV/div 9 TIN 1V/div
9 TIN 500mV/div @ TE 1V/div
0 FIN 1V/div
CD-ROM >> CD-DA mode change(Band key) Black dot(800µm) during play

Ref.: Ref.:
REFO REFO

Mode: Mode:
B Normal Normal

34 DEH-P460MP/XM/UC
1 2 3 4
5 6 7 8

DEH-P460MP/XM/UC 35
5 6 7 8
 1 2 3 4

4. PCB CONNECTION DIAGRAM

4.1 TUNER AMP UNIT
A
NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB A TUNER AMP UNIT CORD A
include all necessary parts for
several destination.
For further information for
WIRED
respective destinations, be sure
to check with the schematic dia- REMOTE
gram. CONTROL
2.Viewpoint of PCB diagrams
1
Connector Capacitor IP-BUS
2
SIDE A
3
B

SIDE B
P.C.Board Chip Part

E
D CN901

DETACH
A SENSE
36 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

CORD ASSY SIDE A

ANTENNA
RCA B

FM/AM TUNER UNIT

D

FRONT B CN1950
A
DEH-P460MP/XM/UC 37
5 6 7 8
 1 2 3 4

A TUNER AMP UNIT

E PCL

A
38 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

SIDE B

PCL E

A
DEH-P460MP/XM/UC 39
5 6 7 8
 1 2 3 4

4.2 PANEL UNIT

B PANEL UNIT SIDE A

C CN1901
EJECT

D B PANEL UNIT SIDE B

A CN831

B
40 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

4.3 KEYBOARD UNIT

C KEYBOARD UNIT
FUNC
SIDE A
C KEYBOARD UNIT SIDE B
A

AUDIO

B CN1951
LOUD

BAND B

2 D

PAUSE
VOLUME

CLOCK
EQ
SRC-OFF
SCRL
F

C
DEH-P460MP/XM/UC 41
5 6 7 8
 1 2 3 4

4.4 CD CORE UNIT(S10WMA)

A D CD CORE UNIT(S10WMA) SIDE A

M2
LOADING
/CARRIAGE
B MOTOR

M1
SPINDLE
MOTOR

C
A CN721
PICKUP UNIT(P10)(SERVICE)

D HOME

D
42 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

D CD CORE UNIT(S10WMA) SIDE B

A

12EJ
8EJ

DSCSNS

CLAMP B

D
DEH-P460MP/XM/UC 43
5 6 7 8
 1 2 3 4

5. ELECTRICAL PARTS LIST

A
NOTE:
• Parts whose parts numbers are omitted are subject to being not supplied.
• The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.

D 931 Diode HZS7L(C3)

B

A
D 932 Diode HZS7L(A1)
D 981 Diode MPG06G-6415G50
D 982 Diode MPG06G-6415G50
Unit Number:XWM7023 (DEH-P460MP, P4600MP)
L 131 Inductor LACU2R2K
:XWM7024(DEH-P4650MP)
Unit Name:Tuner Amp Unit L 401 Inductor LACU4R7K
L 404 Inductor LACU1R0K
L 601 Inductor LACU2R2K
MISCELLANEOUS L 721 Inductor LACU2R2K
L 971 Inductor LACU2R2K
IC 101 IC HA12240FP
IC 131 IC PML003AM
L 981 Choke Coil 600µH CTH1280
IC 301 IC PAL007A
X 601 Radiator 12.58291MHz CSS1402
C IC 601 IC PE5407A
S 831 Switch(DETACH SENSE) CSN1039
IC 651 IC BD4834G
FU351 Fuse 3A CEK1286
Fuse 10A CEK1208
IC 921 IC NJM2391DL1-33
Q 101 Transistor 2SA1576
FM/AM Tuner Unit CWE1646
Q 102 Transistor DTC124EU
SP601 Buzzer CPV1062
Q 301 Transistor DTC124EU
AR401 Surge Protector DSP-201M-S00B
Q 351 Transistor UMH3N

Q 352 Transistor (DEH-P460MP, P4600MP) UMH3N

RESISTORS
Q 502 Transistor UMD2N
Q 601 Transistor DTA114EU R 101 RS1/16S620J
Q 751 Transistor UMD2N R 102 RS1/16S0R0J
Q 752 Transistor 2SD2375 R 103 RS1/16S101J
D
R 104 RS1/16S101J
Q 753 Transistor UMD2N R 105 RS1/16S181J
Q 754 Transistor 2SD1760F5
Q 831 Transistor DTC143EU R 106 RS1/16S181J
Q 901 Transistor 2SD2375 R 107 RS1/16S223J
Q 902 Transistor UMD2N R 108 RS1/16S223J
R 109 RS1/16S102J
Q 911 Transistor 2SD2375 R 110 RS1/16S102J
Q 912 Transistor 2SB1238
Q 913 Transistor DTC114EU R 111 RS1/16S222J
Q 931 Transistor UMX1N R 112 RS1/16S102J
Q 961 Transistor 2SB1238 R 113 RS1/16S332J
R 114 RS1/16S562J
E
Q 962 Transistor DTC114EU R 115 RS1/16S473J
Q 971 Transistor 2SA1577
D 571 Diode MPG06G-6415G50 R 131 RS1/16S471J
D 572 Diode MPG06G-6415G50 R 132 RS1/16S471J
D 751 Diode HZS9L(B1) R 133 RAB4C102J
R 137 RS1/16S101J
D 753 Diode HZS6L(C1) R 138 RS1/16S101J
D 831 Diode DAN202U
D 832 Diode DAN202U R 139 RS1/16S101J
D 833 Diode DAP202U R 140 RS1/16S101J
D 834 Diode DAP202U R 301 RS1/16S153J
R 302 RS1/16S103J
D 835 Diode DAN202U R 303 RS1/16S103J
F
D 836 Diode DAP202U
D 901 Diode HZS6L(B1) R 304 RS1/16S331J
D 902 Diode MPG06G-6415G50 R 351 RS1/16S821J
D 911 Diode HZS9L(B3) R 352 RS1/16S821J
44 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 353 (DEH-P460MP, P4600MP) RS1/16S821J R 752 RD1/4PU221J
R 354 (DEH-P460MP, P4600MP) RS1/16S821J R 755 RS1/16S331J
A
R 359 RS1/16S223J R 801 (DEH-P460MP, P4600MP) RS1/16S102J
R 360 RS1/16S223J R 802 (DEH-P460MP, P4600MP) RS1/16S102J
R 361 (DEH-P460MP, P4600MP) RS1/16S223J R 831 RS1/16S222J
R 362 (DEH-P460MP, P4600MP) RS1/16S223J R 832 RS1/16S222J
R 401 RS1/16S681J R 833 RS1/16S222J

R 403 RS1/16S122J R 834 RS1/16S222J

R 404 RS1/16S681J R 835 RS1/16S473J
R 405 RS1/16S681J R 836 RS1/16S473J
R 406 RS1/16S681J R 837 RD1/4PU391J
R 413 RS1/16S0R0J R 838 RS1/16S102J

R 414 RS1/16S0R0J R 839 RS1/16S102J B

R 415 RS1/16S0R0J R 840 RS1/16S102J
R 416 RS1/16S0R0J R 841 RS1/16S102J
R 417 RS1/16S0R0J R 842 RS1/16S222J
R 504 RS1/16S102J R 843 RS1/16S222J

R 505 RS1/16S0R0J R 845 RS1/16S102J

R 601 RS1/16S102J R 846 RS1/16S102J
R 603 RS1/16S473J R 847 RS1/16S102J
R 605 RS1/16S102J R 848 RS1/16S104J
R 606 RS1/16S473J R 849 RS1/16S473J

R 607 RS1/16S104J R 901 RD1/4PU221J

R 609 (DEH-P460MP, P4600MP) RS1/16S103J R 902 RS1/16S223J C
R 612 RS1/16S0R0J R 903 RS1/16S821J
R 615 (DEH-P460MP, P4600MP) RS1/16S103J R 904 RS1/16S821J
R 617 (DEH-P4650MP) RS1/16S104J R 914 RS1/16S152J

R 618 (DEH-P460MP, P4600MP) RS1/16S104J R 915 RD1/4PU152J

R 620 RS1/16S473J R 916 RS1/16S223J
R 621 RS1/16S473J R 931 RS1/16S104J
R 622 RS1/16S473J R 932 RS1/16S473J
R 623 RS1/16S473J R 933 RS1/16S103J

R 624 RS1/16S473J R 934 RS1/16S473J

R 625 RS1/16S473J R 935 RS1/16S472J
R 626 RS1/16S681J R 961 RS1/16S223J D
R 627 RS1/16S681J R 962 RS1/16S182J
R 628 RS1/16S681J R 963 RS1/16S1R0J

R 632 (DEH-P4650MP) RS1/16S104J R 965 RS1/16S182J

R 633 (DEH-P4650MP) RS1/16S104J R 971 RS1/16S153J
R 640 RS1/16S0R0J R 972 RS1/16S153J
R 651 RS1/16S102J R 973 RS1/16S222J
R 652 RS1/16S183J R 981 RD1/4PU102J

R 711 RS1/16S682J CAPACITORS

R 718 RS1/16S473J
R 721 RS1/16S0R0J C 101 CKSRYB104K16
R 722 RS1/16S682J C 102 CKSRYB473K25 E
R 723 RS1/16S682J C 103 CKSRYB102K50
C 104 CKSRYB102K50
R 724 RS1/16S682J C 131 CEJQ1R0M50
R 727 RS1/16S821J
R 728 RS1/16S821J C 132 CEJQ1R0M50
R 734 RS1/16S102J C 133 CKSRYB104K16
R 738 RS1/16S0R0J C 134 CKSRYB104K16
C 135 CEJQ1R0M50
R 739 RS1/16S0R0J C 136 CEJQ1R0M50
R 743 RS1/16S221J
R 744 RS1/16S221J C 137 CEJQ1R0M50
R 745 RS1/16S221J C 138 CEJQ1R0M50
R 746 RS1/16S221J C 139 CEJQ470M16 F
C 140 CKSRYB104K16
R 747 RS1/16S221J C 141 CKSRYB102K50
R 748 RS1/16S221J
R 751 RD1/4PU221J
DEH-P460MP/XM/UC 45
5 6 7 8
 1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 143 CEJQ100M16 C 931 CKSRYB104K25
C 145 CEJQ4R7M35 C 962 CKSRYB103K50
A C 146 CEJQ4R7M35 C 971 CKSRYB104K25
C 147 CKSRYB153K50
C

C
148

172
CKSRYB153K50

CKSRYB102K50
C
Unit Number:XWM7031 (DEH-P460MP, P4600MP)
C 301 CKSRYB474K10
C 302 CKSRYB474K10
:XWM7032(DEH-P4650MP)
C 303 CKSRYB474K10 Unit Name:Keyboard Unit
C 304 CKSRYB474K10
MISCELLANEOUS
C 305 CKSRYB474K10
C 306 CKSRYB474K10 IC 1901 IC PD6340A
C 307 CKSRYB474K10 IC 1902 IC RS-140
B C 308 CKSRYB474K10 D 1900 Diode DAN202U
C 309 CEJQ330M10 D 1901 Diode DAP202U
D 1915 LED CL-195PG-CD
C 310 3300µF/16V CCH1486
C 311 CKSRYB104K25 D 1918 LED CL-195PG-CD
C 312 CEHAR100M16 D 1919 LED CL-195PG-CD
C 313 CKSQYB225K10 D 1921 LED CL-195PG-CD
C 314 CKSQYB225K10 D 1922 LED CL-195PG-CD
D 1923 LED CL-195PG-CD
C 317 CKSQYB105K16
C 351 CEJQ2R2M50 D 1924 LED CL-195PG-CD
C 352 CEJQ2R2M50 D 1927 LED CL-195PG-CD
C 353 (DEH-P460MP, P4600MP) CEJQ2R2M50 D 1950 LED NSCW505C-3388
C C 354 (DEH-P460MP, P4600MP) CEJQ2R2M50 D 1951 LED NSCW505C-3388
X 1901 Ceramic Resonator 4.97MHz CSS1573
C 401 CKSRYB103K50
C 402 CEJQ470M6R3 S 1901 Switch CSG1107
C 403 CKSRYB103K50 S 1902 Push Switch CSG1112
C 404 CKSRYB103K50 S 1903 Switch CSG1107
C 405 CEJQ101M16 S 1904 Switch CSG1107
S 1905 Switch CSG1107
C 407 CKSYB475K10
C 410 CKSRYB102K50 S 1906 Switch CSG1107
C 601 CKSRYB473K25 S 1907 Switch CSG1107
C 602 CKSRYB105K10 S 1908 Push Switch CSG1112
C 603 CCSRCH200J50 S 1909 Switch CSG1107
D S 1910 Push Switch CSG1112
C 604 CCSRCH200J50
C 605 CEJQ4R7M35 S 1911 Switch CSG1107
C 606 CKSRYB104K16 S 1912 Switch CSG1107
C 608 CCSRCH101J50 S 1913 Switch CSG1107
C 609 CCSRCH470J50 S 1914 Switch CSG1107
S 1915 Push Switch CSG1112
C 611 CKSRYB104K16
C 652 CEJQ1R0M50 S 1916 Switch CSG1107
C 725 CKSRYB102K50 S 1917 Switch CSG1107
C 726 CKSRYB102K50 S 1918 Switch CSG1107
C 727 470µF/16V CCH1331 S 1960 Encoder(VOLUME) XSD7001
S 1961 Push Switch CSG1111
E C 751 CKSRYB224K10
C 752 CKSRYB102K50 LCD1901 LCD (DEH-P460MP, P4600MP) XAW7004
C 753 CEJQ101M16 LCD1901 LCD (DEH-P4650MP) XAW7002
C 754 CKSRYB473K25
C 755 CEJQ101M16 RESISTORS
C 901 CEJQ470M10
R 1900 RS1/16S222J
C 902 CKSRYB103K50
R 1901 RS1/16S222J
C 903 CKSRYB472K50
R 1902 RS1/16S2R2J
C 904 470µF/16V CCH1331
R 1904 RS1/16S121J
C 911 CEJQ221M10
R 1910 RS1/16S181J
C 912 CKSRYB103K50
R 1911 RS1/16S181J
F C 913 CEJQ101M16
R 1912 RS1/16S181J
C 921 CEJQ220M10
R 1913 RS1/16S181J
C 922 CKSRYB103K50
R 1914 RS1/16S181J
C 924 CEJQ4R7M35
R 1915 RS1/16S181J

46 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
IC 203 IC NJM2391DL1-33
R 1916 RS1/16S181J IC 301 IC BA5835FM
R 1917 RS1/16S181J IC 501 IC S-L2980A15MC-C6A A
R 1918 RS1/16S181J IC 701 IC PE5402A
R 1919 RS1/16S181J
R 1920 RS1/16S181J IC 703 IC S-812C33AUA-C2N
Q 101 Transistor 2SB1132
R 1921 RS1/16S181J Q 601 Transistor IMH20
R 1922 RS1/16S181J Q 603 Transistor 2SB709A
R 1923 RS1/16S181J Q 701 Transistor UN2111
R 1925 RS1/16S181J
R 1926 RS1/16S181J D 101 Diode 1SS355
D 601 Diode MA152WA
R 1927 RS1/16S181J L 203 Inductor CTF1389
R 1928 RS1/16S181J L 207 Inductor CTF1389
R 1929 RS1/16S181J L 209 Inductor CTF1389 B
R 1930 RS1/16S181J
R 1931 RS1/16S181J L 703 Inductor CTF1389
X 201 Ceramic Resonator 16.934MHz CSS1603
R 1932 RS1/16S181J X 701 Ceramic Resonator 4.00MHz CSS1652
R 1933 RS1/16S181J S 901 Switch(HOME) CSN1051
R 1934 RS1/16S181J S 902 Switch(CLAMP) CSN1051
R 1935 RS1/16S181J
R 1936 RS1/16S181J S 903 Spring Switch(DSCSNS) CSN1052
S 904 Switch(12EJ) CSN1051
R 1942 RS1/16S181J S 905 Switch(8EJ) CSN1051
R 1945 RS1/16S181J
R 1947 RS1/16S0R0J RESISTORS
R 1948 RS1/16S0R0J C
R 1950 RS1/16S181J R 101 RS1/10S1R5J
R 102 RS1/10S1R5J
R 1951 RS1/16S181J R 103 RS1/10S1R5J
R 1952 RS1/16S151J R 104 RS1/10S1R5J
R 1960 RS1/16S472J R 105 RS1/10S1R5J
R 1980 RS1/16S473J
R 107 RS1/16SS0R0J
CAPACITORS R 201 RS1/16SS102J
R 202 RS1/16SS333J
C 1900 CKSRYB224K10 R 205 RS1/16SS473J
C 1902 CKSYF106Z10 R 207 RS1/16SS473J

B
Unit Number:CWM8758
R
R
R
209
214
216
RS1/16SS473J
RS1/16SS472J
RS1/16SS472J
D

R 218 RS1/16SS472J
Unit Name:Panel Unit R 220 RS1/16SS472J

MISCELLANEOUS R 221 RS1/16SS103J

R 222 RS1/16SS103J
D 1970 LED CL220PGC R 223 RS1/16SS0R0J
S 1970 Push Switch(EJECT) CSG1112 R 224 RS1/16SS0R0J
R 225 RS1/16SS103J
RESISTORS
R 226 RS1/16SS393J
R 1970 RS1/16S101J R 227 RS1/16SS562J E
R 1971 RS1/16S101J R 228 RS1/16SS122J
R 1972 RS1/16S0R0J R 229 RS1/16SS472J
R 231 RS1/16SS0R0J
CAPACITORS
R 232 RS1/16SS122J
C 1970 CKSRYB104K16 R 233 RS1/16SS0R0J
R 240 RS1/16SS0R0J

D
R 241 RS1/16SS333J
R 242 RS1/16SS0R0J
Unit Number:CWX2851
R 243 RS1/16SS333J
Unit Name:CD CORE UNIT(S10WMA) R 245 RS1/16SS333J
R 250 RS1/16SS0R0J F
MISCELLANEOUS R 256 RS1/16SS0R0J
R 261 RS1/16S0R0J
IC 201 IC UPD63761GJ

DEH-P460MP/XM/UC 47
5 6 7 8
 1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 262 RS1/16S0R0J R 777 RS1/16SS221J
R 263 RS1/16S0R0J R 778 RS1/16SS221J
A R 264 RS1/16S0R0J R 779 RS1/16SS221J
R 267 RS1/16S0R0J R 901 RAB4CQ221J
R 301 RS1/16SS183J R 902 RS1/16S0R0J

R 302 RS1/16SS822J R 905 RS1/16SS221J

R 304 RS1/16SS183J R 906 RS1/16SS221J
R 305 RS1/16SS822J R 908 RS1/16SS0R0J
R 307 RS1/16SS183J R 910 RS1/16SS0R0J
R 308 RS1/16SS183J
CAPACITORS
R 309 RS1/16SS183J
R 310 RS1/16SS183J C 101 CKSSYB104K10
R 501 RS1/16SS0R0J C 102 CKSSYB104K10
B R 601 RS1/16S101J C 103 100µF/16V CCH1504
R 602 RS1/16S101J C 104 47µF/6.3V CCH1506
C 105 CKSSYB104K10
R 603 RS1/16S223J
R 604 RS1/16S223J C 106 CCSSCH101J50
R 605 RS1/16SS103J C 107 CKSRYB224K16
R 606 RS1/16S0R0J C 108 CKSSYB104K10
R 701 RS1/16S0R0J C 110 CKSSYB104K10
C 201 CKSSYB471K50
R 702 RS1/16SS0R0J
R 703 RS1/16SS104J C 202 CKSSYB104K10
R 704 RS1/16SS104J C 203 CKSSYB104K10
R 705 RS1/16SS221J C 204 22µF/6.3V CCH1507
C R 706 RS1/16SS221J C 205 CKSSYB104K10
C 207 220µF/4V CCH1590
R 707 RS1/16SS0R0J
R 708 RS1/16SS221J C 208 CKSSYB104K10
R 709 RS1/16SS473J C 209 CKSSYB104K10
R 710 RS1/16SS102J C 216 CKSSYB332K50
R 711 RS1/16SS102J C 217 CKSSYB104K10
C 218 CKSSYB223K16
R 712 RS1/16SS102J
R 713 RS1/16SS102J C 219 CKSSYB104K10
R 714 RS1/16SS473J C 220 CKSSYB103K16
R 715 RS1/16SS0R0J C 221 CKSSYB104K10
R 716 RS1/16SS472J C 222 CCSSCH560J50
D C 223 CCSSCH5R0C50
R 719 RS1/16SS221J
R 720 RS1/16SS471J C 224 CKSSYB104K10
R 721 RS1/16S0R0J C 225 CKSSYB103K16
R 724 RS1/16S473J C 226 CCSSCH680J50
R 725 RS1/16SS222J C 227 CCSSCH470J50
C 228 CKSSYB682K25
R 726 RS1/16SS103J
R 727 RS1/16SS473J C 230 CKSSYB104K10
R 729 RS1/16SS223J C 232 CKSSYB104K10
R 730 RS1/16SS473J C 233 10µF/6.3V CCH1470
R 731 RS1/16SS104J C 234 220µF/4V CCH1590
C 235 CKSRYB224K16
E R 732 RS1/16SS104J
R 733 RS1/16SS104J C 237 CKSSYB104K10
R 735 RS1/16SS473J C 239 CCSSCH330J50
R 737 RS1/16SS104J C 242 CKSSYB104K10
R 740 RS1/16SS473J C 246 CKSSYB104K10
C 250 CKSRYB102K50
R 742 RS1/16SS104J
R 745 RS1/16SS473J C 251 CKSRYB102K50
R 746 RS1/16SS104J C 260 CKSSYB104K10
R 750 RS1/16SS473J C 301 CKSSYB221K50
R 754 RS1/16SS102J C 302 CKSSYB221K50
C 303 CKSSYB472K25
R 755 RS1/16SS102J
F R 756 RS1/16SS104J C 304 CKSSYB103K16
R 765 RAB4CQ221J C 305 100µF/16V CCH1504
R 769 RAB4CQ221J C 306 CKSSYB104K10
R 773 RAB4CQ221J C 307 CKSSYB104K10

48 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

Circuit Symbol and No. Part No.

C 501 CKSRYB224K16

C 505 CKSQYB475K6R3 A
C 601 CCSRCH102J50
C 602 CCSRCH102J50
C 603 4.7µF/25V CCH1568
C 604 4.7µF/25V CCH1568

C 701 CKSSYB104K10
C 702 CKSSYB471K50
C 703 CKSSYB103K16
C 704 4.7µF/25V CCH1592
C 706 CKSSYB104K10

C 707 CKSSYB104K10
C 712 CKSRYB224K16 B
C 713 CKSSYB104K10
C 714 CKSSYB104K10
C 716 CKSSYB103K16

C 720 CKSQYB225K10
C 722 CKSRYB105K10
C 903 CKSSYB471K50
C 906 CKSRYB224K16
C 907 CKSSYB103K16

C 910 CKSQYB225K10

Miscellaneous Parts List C

Pickup Unit(P10)(Service) CXX1641

M 1 Motor Unit(SPINDLE) CXB6007
M 2 Motor Unit(LOADING/CARRIAGE)CXB8933

DEH-P460MP/XM/UC 49
5 6 7 8
 1 2 3 4

6. ADJUSTMENT
6.1 CD ADJUSTMENT
A

1) Cautions on adjustments 2) Test mode

• In this product the single voltage (3.3V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65V) • To enter the test mode.
instead of the GND. While pressing the 4 and 6 keys at the same time, reset.
If you should mistakenly short the REFO1 with the GND • To exit from the test mode.
during adjustment, accurate voltage will not be obtained, Turn off the ACC and back up.
and the servo’s misoperation will apply excessive shock
to the pickup. To avoid such problems: Notes:
a. Do not mix up the REFO1 with the GND when a. During ejection, do not press any other keys than the
connecting the (-) probe of measuring instruments. EJECT key until the loaded disc is ejected.
B
Especially on an oscilloscope, avoid connecting the (-) b. If you have pressed the (→) key or (←) key during focus
probe for CH1 to the GND. search, turn off the power immediately to protect the
b. In many cases, measuring instruments have the same actuator from damage caused by the lens stuck.
potential as that for the (-) probe. Be sure to set the c. For the TR jump modes except 100TR, the track jump
measuring instruments to the floating state. operation will continue even if the key is released.
c. If you have mistakenly connected the REFO1 to the GND, d. For the CRG move and 100TR jump modes, the tracking
turn off the regulator or the power immediately. loop will be closed at the same time when the key is
released.
• Before mounting and removing filters or leads for e. When the power is turned off and on, the jump mode
adjustment, be sure to turn off the regulator. is reset to the single TR (91), the RF amp gain is set to 0dB,
and the auto-adjustment values are reset to the default
C
• For stable circuit operation, keep the mechanism settings.
operating for about one minute or more after the
regulator is turned on.

• In the test mode, any software protections will not

work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.

• The RFI and RFO signals with a wide frequency range

are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.

D • The load and eject operation is not guarantied with the

mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.

50 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

- Flow Chart
[4]+[6]+Reset or A
[KEY]
[4]+[6]+BU+ACC
Contents
Test Mode In
Display

[CD]or[SOURCE]
Source On

TRK MIN SEC

[BAND] [3] [2] [4]

Power On Power On RF AMP *1 SPINDLE *9
(T.Offset is adjusted) (T.Offset is not adjusted) Gain switching Speed switching
TRK 00 MIN00 SEC 00 TRK 99 MIN 99 SEC 99 TRK GGMIN GGSEC GG TRK SP MIN SP SEC SP
B

[BAND] [3] [6] [1] [→] [←] [2]

*3
Focus Close Focus Mode Tracking Servo CRG+ *8 *8 Automatic adjustment
Power Off *2
Close CRG-
S.Curve check switching display switching
TRK MIN SEC TRK
91 MIN91 SEC 91 TRK
0x MIN0x SEC 0x TRK
00 MIN00 SEC00 TRK
00 MIN00 SEC00 TRK
00 MIN00 SEC00 TRK
?? MIN?? SEC ??
TRK
or 99 MIN99 SEC99 or TRK
99 MIN99 SEC 99 or TRK
99 MIN 99 SEC 99

[BAND] [1] [6] [3] [→] [←] [2]

T.Close and AGC T.Close RF AGC / CRG+ CRG- T.Balance adjustment /
Power Off Applicable servomechanism RF AGC coefficient display T.Balance coefficient display
Applicable servomechanism
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK ?? MIN ?? SEC ?? TRK8x MIN8x SEC8x TRK8x MIN8x SEC8x TRK ?? MIN?? SEC ??
?tr ?min ?sec ?tr ?min ?sec or TRK 9x MIN 9x SEC 9x or TRK 9x MIN 9x SEC 9x
C

[BAND] [1] [3] [6] [→] [←] [2]

*7 *5 *4 *4
F, T, RF AGC F, T AGC / F.Bias CRG/TR Jump Tracking Open
Power Off CRG/TR Jump + CRG/TR Jump -
F.Bias display switching RF AGC value switching
TRK MIN SEC TRK
?? MIN?? SEC ?? TRK
?tr
MIN SEC
?min ?sec
TRK
?tr
MIN SEC
?min ?sec
TRK
?tr
MIN SEC
?min ?sec
TRK
?tr
MIN SEC
?min ?sec
TRK
8x MIN8x SEC 8x
TRK
or 9xMIN 9xSEC 9x
*6

[BAND] [2]

Power Off Tracking Open

TRK MIN SEC TRK8x MIN8x SEC8x

or TRK 9x MIN 9x SEC 9x

*1) TYP → -6dB → -12dB Operation

TRK MIN SEC TRK 06 MIN 06 SEC 06 TRK 12 MIN 12 SEC 12 [Key]
Test Mode

[BAND] Power On/Off

*2) Focus Close → S.Curve ckeck setting → F EQ measurement setting
TRK 00 MIN 00 SEC 00 TRK 01 MIN 01 SEC 01 TRK 02 MIN 02 SEC 02
(TRK 99 MIN 99 SEC 99) CRG + / TR Jump +
[→]
(Direction of the external surface)
CRG - / TR Jump -
[←]
*3) F.Offset Display → T.Offset Display → Switch to the order of the original display (Direction of the internal surface)
T.CLS and AGC and Applicable servomechanism /
[1]
AGC, AGC display switching
*4) 1TR / 32TR / 100TR RF Gain switching / Offset adjustment display / E
[2]
T.Balance adjustment / T.Open
*5) Single TR → 32TR → 100TR → CRG Move
9x(8x) : 91(81) 92(82) 93(83) 94(84) [3] F.Close, S.Curve / Rough Servo and RF AGC / F, T, RF AGC

*6) Only at the time of CRG Move, 100TR Jump SPDL 1X/2X switching
[4]
As for the double speed (2x), audio output cannot be supported.
*7) TRK/MIN/SEC → F.AGC → T.AGC → F.Bias → RF AGC Error Rate measurement 1st-ON : ERR count beginning(30Sec)
[5]
2nd-ON : BER display data[%]

*8) CRG motor voltage = 2[V] [6] F. Mode switching / Tracking Close / CRG, TR Jump switching

*9) TYP(1X) → 2X → 1X
TRK MIN SEC TRK 22 MIN 22 SEC 22 TRK 11 MIN 11 SEC 11

As for the double speed (2x), audio output cannot be supported.

TYP(2X) → 1X → 2X
TRK MIN SEC TRK 11 MIN 11 SEC 11 TRK 22 MIN 22 SEC 22
F

DEH-P460MP/XM/UC 51
5 6 7 8
 1 2 3 4

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

B • Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO1
• Disc • ABEX TCD-782
• Mode • TEST MODE

CD CORE UNIT(S10WMA)
C

L.P.F.

REFO1 Xch Ych

E 100kΩ
Oscilloscope
VREF 390pF

F 100kΩ

VREF 390pF

D L.P.F.

F E

• Checking Procedure
1. In test mode, load the disc and switch the 3V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
E 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
difference is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

52 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

Grating waveform Ech → Xch 20mV/div, AC

Fch → Ych 20mV/div, AC A

0° 30°

45° 60°

75° 90°

DEH-P460MP/XM/UC 53
5 6 7 8
 1 2 3 4

6.3 ERROR MODE

- Error Messages
A
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.

B 2) Head unit display examples

Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display

ERROR–xx ERR–xx E–xx

(2) Error Code List

Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
C munication Error → Failure on home switch or CRG move mechanism.
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
→ Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG → Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
D
→ Damages or stains on disc, or excessive vibrations on REWRITABLE.
30 Electricity Search Time Out Failed to reach target address.
→ CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
→ Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
→ Failure on SW transistor or power supply (failure on connector).
E Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.

54 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

6.4 SYSTEM MICROCOMPUTER TEST PROGRAM

- PCL output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode
cancelled), shift the TESTIN (Pin 5) terminal to H.
The clock signal is output from the PCL terminal (Pin 62).
The frequency of the clock signal is 786.432kHz that is one 4th of the fundamental frequency.
The clock signal should be 786.432kHz ± 32Hz.
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.

DEH-P460MP/XM/UC 55
5 6 7 8
 1 2 3 4

7. GENERAL INFORMATION
7.1 DIAGNOSIS
A 7.1.1 DISASSEMBLY

- Removing the Case (not shown)

1. Remove the Case.

- Removing the CD Mechanism Module (Fig.1) CD Mechanism Module

1 Remove the four screws.

B

Disconnect the connector and then remove the 1

CD Mechanism Module.
1

- Removing the Grille Assy (Fig.1)

2 Remove the two screws and then remove the

Grille Assy.
1
2 2
C
1

Grille Assy Fig.1

- Removing the Tuner Amp Unit (Fig.2) Holder

1 2
Remove the screw and then remove
the Holder. 2 1
D 2
2 Remove the three screws.

3 Remove the screw.

4 Straighten the tabs at three locations

indicated. 5
3
E
5 Remove the screw and then remove
the Tuner Amp Unit.

4 4 4

Tuner Amp Unit Fig.2

F

56 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

- How to hold the Mechanism Unit

1. Hold the top and bottom frame.
A
2. Do not squeeze top frame's front portion too tight,
because it is fragile.

Do not squeeze.

- Removing the Upper and Lower Frames

1. With a disc clamped, remove the four springs (A),
Upper Frame
the two springs (B), the two springs (C), and the A
four screws. A
2. To remove the upper frame, open it on the fulcrum C
C
A.
3. While lifting the carriage mechanism, remove the A
three dampers.
4. With the frames removed, insert the connectors
coming from the main unit and eject the disc.
Caution: Before installing the carriage mechanism in
the frames, be sure to apply some alcohol to the A
dampers and set the mechanism to the clamp mode.

Carriage Mechanism
B C
A
Damper
Lower Frame D
Damper

B Damper

DEH-P460MP/XM/UC 57
5 6 7 8
 1 2 3 4

- Removing the Pickup Unit

1. Apply shorting solder to the Pickup flexible cable.
A
Disconnect the cable.
2. Set the mechanism to the clamp mode.
3. Remove the lead wires from the inner holder.
4. Remove the washer, styling holder, change arm,
and pickup lock arm. Shorting
5. While releasing from the hook of the inner holder, Solder
lift the end of the feed screw.
Caution: In assembling, move the planet gear to the
load/eject position before setting the feed screw
in the inner holder.

C Washer
Pickup Lock Arm

Styling Holder Change Arm

Feed Screw

E
Inner Holder
Planet Gear

58 DEH-P460MP/XM/UC
1 2 3 4
 5

5
16 14 12 10 8 6 4 2

15 13 11 9 7 5 3 1 8 9 10 11
5 6 7

1 2 3 4
10A

6
6

POWER SUPPLY IP-BUS

ANTENNA JACK 1. B. UP 9. RL- 1. BUS+ WIRED
REMOTE
7.1.2 CONNECTOR FUNCTION DESCRIPTION

REAR OUTPUT 2. GND 10. FL- 2. IPGND

3. ACC 11. RL+ 3. IPGND CONTROL
FRONT OUTPUT
4. NC 12. FL+ 4. NC (UC Model only)
(UC Model only)
5. NC 13. RR- 5. BUS-
6. B.REM 14. FR- 6. IPGND

DEH-P460MP/XM/UC
7. NC 15. RR+ 7. BUSL+
8. NC 16. FR+ 8. ASENB1

7
7

9. BUSR+
10. BUSR-
11. BUSL-
8

8
59
E
A

D
C

F
B
 1 2 3 4

7.2 PARTS
7.2.1 IC
A
- Pin Functions(PE5407A)
Pin No. Pin Name I/O Format Function and Operation
1 swvdd O C Grille : Chip enable output
2-4 NC Not used
5 TESTIN I Test program mode input
6 LCDPW Not used
7 TELIN I Telephone mute input
8 ejectin I Eject sense input
9 FLPILM O C Flap illumination output
10 DALMON O C For consumption low-current output
11 reset I Reset input
B 12 XT2 Not used
13 XT1 I Clock connection pin
14 VSS GND
15 X2 Crystal oscillator connection pin
16 X1 I Crystal oscillator connection pin
17 REGOFF Regulator operation specification signal
18 REGC Capacitor for regulator connect pin
19 VDD Power supply
20 ILMPW O C Illumination power supply control output
21 SYSPW O C System power control output
22 adpw O C A/D converter power supply control output
23 NC Not used
C 24 IPPW O C Power supply control output for IP BUS interface IC
25 NC Not used
26 ROMDATA O C ROM correction data output
27 ROMCLK Not used
28 ROMCS Not used
29-31 NC Not used
32 tunpce@ O C PLL chip enable output2
33 VST O C E.VOL : Strobe output
34 VCK O C E.VOL : Clock output
35 VDT O C E.VOL : Data output
36 ANTPW Not used
37 MUTE O C System mute output
D 38, 39 NC Not used
40 VSS GND
41 VDD Power supply
42 RDS57K Not used
43 drst Not used
44 rdslk Not used
45 RDT Not used
46 DORAON Not used
47 NC Not used
48 CSENSOUT O C CSENS state output
49-55 NC Not used
56,57 ROT1,0 I Rotary encoder pulse input 1,0
E 58 STRKEY2 O C Steering remote controller output
59 CDLOEJ O C CD : Load Moter Load/Eject output
60 CLCONT O C CD : Driver input switch output
61 CONT O C CD : Servo driver power supply control output
62 PCL O C Clock adjustment output
63 CLAMPSW I Clamp SW input
64 VDCONT O C CD : VD power control output
65 xsck O C CD LSI clock output
66 XSI I CD LSI data input
67 XSO O C CD LSI data output
68 XAO O C CD LSI command/data control output
69 xrst O C CD LSI reset control output
F
70 xstb O C CD LSI strobe output

60 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

Pin No. Pin Name I/O Format Function and Operation

71 ASENSBO O C IP-BUS : Slave power supply control output A
72 EMUTE Not used
73 TEST I GND
74 SL I TUNER : Signal level input
75 STRKEY1 I Steering remote controller input
76 MODELIN Not used
77 CSENS I Flap close sense input
78 NC Not used
79 DSCSNS I CD : Disc insert sense input
80 VDSENS I CD : VD voltage sense input
81 TEMP I CD : Temperature sense input
82 AVDD A/D converter power supply terminal
83 AVREF A/D converter reference voltage terminal B
84 AVSS GND
85 RX I IP-BUS : Data input
86 TX O C IP-BUS : Data output
87 NMI GND
88 ldet I PLL lock sense input
89 rck I RDS : Clock input
90 dsens I Grille detach sense input
91 PACK I PACK input
92 asens I ACC power sense input
93 bsens I Back up power sense input
94 TUNPDI I PLL IC data input
95 KYDT I Grille data input C
96 DPDT O C Grille data output
97 TUNPCK O C PLL clock output
98 TUNPDO O C PLL data output
99 TUNPCE O C PLL chip enable output
100 PEE O C Beep tone output

* PE5407A IC's marked by * are MOS type.

Be careful in handling them because they are very
30 1 liable to be damaged by electrostatic induction.
31
100 Format Meaning
D
C CMOS

BD4834G
N.C.

N.C.

50
81 5 4

51 80

Vref

1 2 3
VOUT

VDD

GND

DEH-P460MP/XM/UC 61
5 6 7 8
 1 2 3 4

HA12240FP

A STB VCC BUS+ BUS-

8 7 6 5

BIAS

+ DRIVER
- OUTPUT

+
RECEIVER COM
OUTPUT -
B

1 2 3 4
S1 R S2 GND

- Pin Functions (PD6340A)

Pin No. Pin Name I/O Function and Operation
1-5 SEG4-0 O LCD segment output
6-9 COM3-0 O LCD common output
C 10 VLCD LCD drive power supply
11-14 KST3-0 O Key strobe output
15,16 KDT0,1 I Key data input (analogue input)
17 REM I Remote control reception input
18 DPDT I Display data input
19 NC Not used
20 KYDT O Key data output
21 MODA GND
22 XO Crystal oscillator connection pin
23 XI Crystal oscillator connection pin
24 VSS GND
25,26 KDT2,3 I Key data input
D 27,28 KST5,4 O Key strobe output
29-55 SEG39-13 O LCD segment output
56 VDD Power supply
57-64 SEG12-5 O LCD segment output

*PD6340A

48 33
49 32

64 17

1 16

62 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

- Pin Functions(PE5402A)
Pin No. Pin Name I/O Format Function and Operation
1 AVREF A power supply Positive power supply(5V)
A
2 AVSS A power supply GND
3 RFOK O C Output of state of RFOK
4 CLAMP I C CLAMP SW sense input
5 EVDD E power supply Positive power supply
6 PWM For changer(PWM)
7 NC Not used
8 IC/FLMD0 IC : VSS direct connection/FLMOD0 : Pull-down
9 VDD Positive power supply(5V)
10 REGC Connected to the capacity stabilizing output of the regulator
11 VSS GND
12 X1 I Oscillator connection for mainclock
13 X2 Oscillator connection for mainclock B
14 reset I System reset input
15 XT1 I Connected to the oscillator for subclock
(connected to VSS via the resistor)
16 XT2 Connected to the oscillator for subclock(Open)
17 PULLDOWN I Connected to EVDD or EVSS via the resistor
18 ejsw I C Eject key input
19 xint C CD LSI interruption signal input
20 NC Not used
21 brst I P-Bus reset input
22 BSI I P-Bus serial data input
23 BSO O C P-Bus serial data output
24 bsck I/O /C P-Bus serial clock input/output C
25 FTXD O C For flash rewriting(transmitted signal)
26 FRXD I For flash rewriting(received signal)
27 BRXEN I/O /C It is possible to receive P-Bus
28 bsrq I/O /C P-Bus service request demand
29 dspok I DSP microcomputer initialization OK input
30 DSCSNS(S903) I Disc state sense input
31 8EJ(S905) I Input of detection of 8 cm disc ejection
32 12EJ(S904) I Input of detection of 12 cm disc ejection
33 EVSS E power supply GND
34 EVDD E power supply Positive power supply
35, 36 SRAMLEVEL0, 1 O C SRAM level meter output
37 EMPH O C Emphasis information output D
38 emph O C Emphasis information output
39-42 NC Not used
43 adena O C A/D reference voltage supply control output
44 LRCKOK O C (DOUT mute output)
45 SRAMLEVEL2 O C SRAM level meter output
46 CD3VON O C CD +3.3V power supply control output
47 CONT O C Servo driver power supply control output
48 xrst O C CD LSI reset control output
49 VDCONT O C VD power supply control output
50 ROMDATA I/O /C E2PROM data input/output
51 ROMCS O C E2PROM chip selection output
52 ROMCK O C E2PROM clock output E
53 LOEJ O C The direction change output of LOAD/EJECT
54 CLCONT O C Driver input change output
55 CDMUTE O C CD mute control output
56-58 INT For changer(Interruption at the edge)
59 xcs O C CD LSI chip selection output
60 NC Not used
61 xwait I CD LSI write control signal output
62 CLKOUT O C Internal system clock output(Open)
63 LOCK I Spindle lock input
64 NC Not used
65 xwrite O CD LSI write control signal output
F

DEH-P460MP/XM/UC 63
5 6 7 8
 1 2 3 4

Pin No. Pin Name I/O Format Function and Operation

66 NC Not used
A 67 xread O CD LSI read control signal output
68 XASTB O CD LSI address strobe output
69 BVSS B power supply GND
70 BVDD B power supply Positive power supply
71-86 AD0-15 I/O /C Address/data Bus 0-15
87-90 NC Not used
91-93 A/D For changer(A/D)
94 csens I Flap closing sense input
95 TYPE_A/D I CD-DA analog/digital output change setup
96 testin I Chip check test program starting input
97 HOME I Home SW sense input
B
98 TEMP Temperature information sense input
99 VDSENS VD power supply short sense input
100 NC Not used

* PE5402A

Format Meaning
51
75

C CMOS
76 50

* S-812C33AUA-C2N

100 26
25
1

Reference
Voltage

1 2 3
VSS

VIN

VOUT

64 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

- Pin Functions(UPD63761GJ)
Pin No. Pin Name I/O Function and Operation
1 D.VDD Power supply for digital circuits A
2 D1.GND GND for 1.6V digital circuits
3 reset I Input of reset
4-8 AB12-8 I Address bus 12-8 from the microcomputer
9-16 AD7-0 I/O Address/data bus 7-0 to the microcomputer
17 cs I Chip selection
18 ASTB I Address strobe
19 read I Control signals(read)
20 write I Control signals(write)
21 wait O Control signals(wait)
22 INTQ O Interruption signals to the external microcomputer
23, 24 IFMODE0, 1 I Switching the microcomputer I/F 0, 1
25 D1.VDD Power supply for 1.6V digital circuits B
26 DA.VDD Power supply for DAC
27 ROUT O Output of audio for the right channel
28 DA.GND GND for DAC
29 REGC Connected to the capacitor for band gap
30 DA.GND GND for DAC
31 LOUT O Output of audio for the left channel
32 DA.VDD Power supply for DAC
33 X.VDD Power supply for the crystal oscillator
34 XTAL I Connected to the crystal oscillator(16.9344MHz)
35 xtal O Connected to the crystal oscillator(16.9344MHz)
36 X.GND Ground for the crystal oscillator
37 VDDREG15 Control of 1.6V regulator C
38 PWMSW0 I Setup 0 for PWM output(SD, MD)
39-41 TEST3-1 I Connected to GND
42 PWMSW1 I Setup 1 for PWM output(FD, TD)
43 TESTEN I Connected to GND
44 D1.GND GND for 1.6V digital circuits
45 DIN I Input of audio data
46 DOUT O Output of audio data
47 SCKIN I Clock input for audio data
48 SCKO O Clock output for audio data
49 LRCKIN I Input of LRCK for audio data
50 LRCK O Output LRCK for audio data
51 xtalen I Permission to oscillate 16.9344MHz D
52 D1.VDD Power supply for 1.6V digital circuits
53 RFCK/HOLD O Output of RFCK/HOLD signal
54 WFCK/MIRR O Output of WFCK/MIRR signal
55 PLCK O Output of PLCK
56 LOCK/RFOK O Output of LRCK/Output of RFOK
57 C1D1/C8M O Information on error correction/C8M : 8MHz
58 C1D2/C16M O Information on error correction/C16M : 16MHz
59 C2D1/RMUTE O Information on error correction/Mute for Rch
60 C2D2/LMUTE O Information on error correction/Mute for Lch
61 C2D3/SHOCK O Information on error correction/Detection of vibration
62 D1.GND GND for 1.6V digital circuits
63 C33M O Output of 33.8688MHz(CLK for SDRAM) E
64 (rcs) O DRAM cs
65 RA11 O Output of DRAM address 11
66 (CKE) O Output of DRAM CKE
67 ras O Output of DRAM ras
68 cas)(LDQM) O Output of DRAM lower cas(LDQM)
69 cas!(UDQM) O Output of DRAM upper cas(UDQM)
70 we O Output of DRAM we
71 oe(cas) O Output of DRAM oe(cas)
72 D.GND Ground for digital circuits
73-88 RDB0-15 I/O Input/output of DRAM data0-15
89-99 RA0-10 O Output of DRAM address0-10 F

DEH-P460MP/XM/UC 65
5 6 7 8
 1 2 3 4

Pin No. Pin Name I/O Function and Operation

100 D.VDD Power supply for digital circuits
A
101 FD+ O Output of focus drive PWM +
102 FD- O Output of focus drive PWM -
103 TD+ O Output of tracking drive PWM +
104 TD- O Output of tracking drive PWM -
105 SD+ O Output of thread drive PWM +
106 SD- O Output of thread drive PWM -
107 MD+ O Output of spindle drive PWM +
108 MD- O Output of spindle drive PWM -
109 REFOUTSV O REFOUT for servo
110 AD.VDD Power supply for ADC
111 EFM O Output of EFM signals
B 112 ASY I Input of asymmetry
113 ATEST O Analog tests
114 RFI I Input of RF
115 AD.GND Ground for the analog system
116 AGCO O Output of RF
117 C3T O Connection to the capacitor for detecting 3T
118 AGCI I Input of AGC
119 RFO O Output of RF(AGC)
120, 121 EQ2, 1 I Equalizer 2, 1
122 RF2- I Reversal input of RF2
123 RF- I Reversal input of RF
124 A.GND Ground for the analog system
C 125 A I Input of A
126 C I Input of C
127 B I Input of B
128 D I Input of D
129 F I Input of F
130 E I Input of E
131 VREFIN I Input of reference voltage
132 A.VDD Power supply for the analog system
133 REFOUT O Output of reference voltage
134 REFC I Connected to the capacitor for output of REFOUT
135 FE- I Reversal input of FE
136 FEO O Output of FE
D 137 ADIN I Input of FE, TE A/D converter
138 TE- I Reversal input of TE
139 TEO O Output of TE
140 TE2 O TE2
141 TEC I TEC
142 LD O Output of LD
143 PD I Input of PD
144 D.GND Ground for digital circuits

* UPD63761GJ
108

73

E
109 72

144 37
F
1

36

66 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

- Pin Functions(BA5835FM)
Pin No. Pin Name Function and Operation
1 VR Input pin for reference voltage
A
2 OPIN2(+) Input pin for non-inverting input for CH2 preamplifier
3 OPIN2(-) Input pin for inverting input for CH2 preamplifier
4 OPOUT2 Output pin for CH2 preamplifier
5 OPIN1(+) Input pin for non-inverting input for CH1 preamplifier
6 OPIN1(-) Input pin for inverting input from CH1 preamplifier
7 OPOUT1 Output pin for CH1 preamplifier
8 GND Ground pin
9 MUTE Mute control pin
10 POWVCC1 Power supply pin for CH1, CH2, and CH3 at "Power" stage
11 VO1(-) Driver CH1 - Negative output
12 VO1(+) Driver CH2 - Positive output
13 VO2(-) Driver CH2 - Negative output
B
14 VO2(+) Driver CH2 - Positive output
15 VO3(+) Driver CH2 - Positive output
16 VO3(-) Driver CH2 - Negative output
17 VO4(+) Driver CH4 - Positive output
18 VO4(-) Driver CH4 - Negative output
19 POWVCC2 Power supply pin for CH4 at "Power" stage
20 GND Ground pin
21 CNT Control pin
22 LDIN Loading input
23 OPOUTSL Output pin for preamplifier for thread
24 OPINLSL Input pin for preamplifier for thread
25 OPOUT3 CH3 preamplifier output pin C
26 OPIN3(-) Input pin for inverting input for CH3 preamplifier
27 OPIN3(+) Input pin for non-inverting input for CH3 preamplifier
28 PREVCC PreVcc

BA5835FM
14 1

* S-L2980A15MC-C6A
D
VOUT NC
15 28
5 4
+
-

Reference
voltage
ON/OFF
circuit

1 2 3
VIN VSS ON/OFF

DEH-P460MP/XM/UC 67
5 6 7 8
 1 2 3 4

- FM/AM Tuner Unit

7 6 13 5 10 9 8 11 14 18 19 20 21

WC
CE2

ROM_VDD

SL

DI
CK
CE1

DO
NC

NC

NC

NC

NC
A

IC 3 EEPROM IC 5
←
5.0V 5V 3.3V

OSC LPF

AM ANT FMRF
1 ATT
Rch
24
IC 2
IC 1 2.5V
FM ANT
3 3.3V
ATT Lch
B FMRF MIXER, IF AMP DET, FM MPX
23

RF adj
ANT adj

T51 CF52
CF51
AUDIOGND

IC 4
OSCGND

VDD_3.3

←
RFGND

3.3V 3.3V 2.5V 2.5V

DGND

VCC
NC

2 12 15 22 16 4 17

C No. Symbol I/O Explain

1 AMANT I AM antenna input AM antenna input high impedance AMANT pin is connected with
an all antenna by way of 4.7µH. (LAU type inductor) A series circuit
including an inductor and a resistor is connected with RF ground for
the countermeasure against the hum of power transmission line.
2 RFGND RF ground Ground of antenna block
3 FMANT I FM antenna input Input of FM antenna 75Ω Surge absorber(DSP-201M-S00B) is necessary.
4 VCC power supply The power supply for analog block. D.C 8.4V ± 0.3V
5 SL O signal level Output of FM/AM signals level
6 CE2 I chip enable-2 Chip enable for EEPROM ”Low” active
7 WC I write control You can write EEPROM, when EEPROM write control is “Low”.
Ordinary non connection
D 8 CE1 I chip enable-1 Chip enable for AF•RF ”High” active
9 CK I clock Clock
10 DI I data in Data input
11 NC non connection Not used
12 OSCGND osc ground Ground of oscillator block
13 ROM_VDD power supply Power supply for EEPROM pin 13 is connected with a power supply of
micro computer.
14 DO O data out Data output
15 DGND digital ground Ground of digital block
16 NC non connection Not used
17 VDD_3.3 power supply The power supply for digital block. 3.3V ± 0.2V
18 NC non connection Not used
E 19 NC non connection Not used
20 NC non connection Not used
21 NC non connection Not used
22 AUDIOGND audio ground Ground of audio block
23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output
24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output

68 DEH-P460MP/XM/UC
1 2 3 4
 8 7 6 5
69 DEH-P460MP/XM/UC
SEG39
F
SEG38
SEG37
SEG36
COMMON
SEGMENT

COM 3 COM 3
COM 2 COM 2
COM 1 COM 1
COM 0 COM 0
SEG35
E SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
D
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
C SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG 9
B
SEG 8
SEG 7
SEG 6
SEG 5
SEG 4
SEG 3
SEG 2
SEG 1
A SEG 0
- LCD(XAW7004)(DEH-P460MP/XM/UC, DEH-P4600MP/XM/UC)
7.2.2 DISPLAY
8 7 6 5
4 3 2 1
DEH-P460MP/XM/UC 70
F
SEG39
SEG38
SEG37
COMMON
SEGMENT

SEG36
COM 3
COM 2
COM 1
COM 0
E
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
D
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
C
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG 9
SEG 8 B
SEG 7
SEG 6
SEG 5
SEG 4
SEG 3
SEG 2
SEG 1
SEG 0
A
- LCD(XAW7002)(DEH-P4650MP/XM/ES)
4 3 2 1
 5 6 7 8

7.3 OPERATIONAL FLOW CHART

Power ON A

VDD=5V
Pin 41

bsens
Pin 93

B
bsens=L

asens
Pin 92

asens=L

dsens
Pin 90

dsens=L
C

ASENSBO←H
Pin 71

CSENS
- CSENS <= 2V, 3V <
= CSENS
Pin 77
Last source returns.
2V < CSENS < 3V CD loading functions are available.
Starts Keys except for EJECT key are not available.
communication
with Grille D
microcomputer. 300ms

swvdd←L
Pin 1 300ms

In case of the above signal, the communication

with Grille microcomputer may fail.
Source keys
If the time interval is not 300msec, the oscillator
operative
may be defective.

Source ON

SYSPW←H
Pin 21

Completes power-on operation.

(After that, proceed to each source operation)
F

DEH-P460MP/XM/UC 71
5 6 7 8
 1 2 3 4

7.4 CLEANING

Before shipping out the product, be sure to clean the

following portions by using the prescribed cleaning
tools:
Portions to be cleaned Cleaning tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008

72 DEH-P460MP/XM/UC
1 2 3 4
 5 6 7 8

8. OPERATIONS
A

DEH-P460MP/XM/UC 73
5 6 7 8
 1 2 3 4

74 DEH-P460MP/XM/UC
1 2 3 4
5 6 7 8

DEH-P460MP/XM/UC 75
5 6 7 8
 1 2 3 4

Fixing the Front Panel

A If you do not operate the Detaching and Replacing the Front Panel Function, use the supplied fixing screws
and fix the front panel to this unit.

1. Attach the holders to both sides of the front panel.

Holder
CND1250(UC)
CXX1645(ES)

Holder
B CND1249(UC)
CXX1644(ES)

2. Replace the front panel to the unit.

3. Flip the holders into upright positions.

4. Fix the front panel to the unit using fixing screws.

Fixing screw
BPZ20P060FZK(UC)
CXX1646(ES)

76 DEH-P460MP/XM/UC
1 2 3 4
 5

5
Multi-CD player
(sold separately) Power amp
IP-BUS cable (sold separately)
Connecting cords
with RCA pin plugs
(sold separately)
Power amp
(sold separately)
This product
IP-BUS input (Blue)
Rear output
- CONNECTION DIAGRAM

(REAR OUTPUT)

Antenna jack Fuse Jack for the Wired Remote Control

Front output Please see the Instruction Manual for the
(FRONT OUTPUT) Wired Remote Control (sold separately).

Blue/white
To system control terminal of the power amp

6
6

or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

System remote control

Yellow
To terminal always supplied
with power regardless of
ignition switch position.

White Gray
Red
To electric terminal controlled + +
Front speaker Front speaker
by ignition switch (12 V DC)
ON/OFF. ≠ ≠

DEH-P460MP/XM/UC
White/black Gray/black
Left Right
Green Violet
Black (ground) + +

7
7

To vehicle (metal) body. Rear speaker Rear speaker

With a 2 speaker system, do not connect
anything to the speaker leads that are not ≠ ≠
Green/black Violet/black
connected to speakers.

Perform these connections when using + +

the optional amplifier. Rear speaker Rear speaker
≠ ≠

Left Right

+ +
8

8
Front speaker Front speaker
≠ ≠

77
E
A

D
C

F
B
www.s-manuals.com