Mode 5 & 6 PTCTM Regular Spring Return Actuator

Spring return actuator with ETR

24V AC/DC and 230V AC

Application
The spring-return actuator is intended for
the operation Actionair Smoke/Shield
PTCTM Hot/Shield PTCTM and Marine A-
60 dampers.

Mode of operation
Wiring Diagram
The actuator motors the damper to the
reset position whilst simultaneously
~ AC 24V BAM24-1: connect via safety
tensioning the return spring. If the power
RAMII-AA-24-1: connect via safety
- + DC 24V isolating
Isolatingtransformer
transformer supply is interrupted, the energy stored in
N L1 AC 230V ! the spring, moves the damper back to the
RAMII-AA-230-1: For disconnection from the supply, a
BAM230-1: For disconnection from the supply, a released position to give fail-safe
separate device must be incorporated in the fixed wiring (at
separate device must be incorporatet in the fixed
least 3mm contact gap in all poles)
wiring (at least 3 mm contact gap in all poles). operation
The ETR incorporates a safety feature
that ensures the fail-safe status of the
damper if the ETR is not fitted to the
1 2 S1
1 S2
2 S3
3 S4
4 S5
5 S6
6
ductwork.
The ETR probe has a replaceable 72°C
Thermal trip
5° 80° BAM24-1
MODE / 230-1
5/6 MKII An LED on the ETR housing indicates:

Unit receiving power
ETR
ETR correctly fitted

Thermal fuse intact
Tf1 Tf2 Tf3
[NOTE: thermal fuse (Tf1) in the ETR housing
will operate (permanently) at 71°C].
Technical Data Mode 5 MKII Mode 6 MKII
Nominal Voltage AC 24V 50/60 Hz AC 230V 50/60 Hz Signalling
- There are two fixed internal micro-
Nominal voltage range AC 19,2...28.8V AC 198...264V switches for indicating the end-positions
- of the damper.
For wire sizing 12.5 VA (Imax 8,3A @ 14 VA (0,5 A @ 5ms) Intermediate positions of the damper
5ms)
blade are visible by the use of a
Power consumption
- motoring 10 W 12 W mechanical pointer.
- holding 2W 4W
Connecting cable (LSF quality) Manual operation
- Motor 1 m 2 x 0.75 mm2 1 m 2 x 0.75 mm2 The damper can be operated manually
- Aux. switch 1 m 6 x 0.75 mm2 1 m 6 x 0.75 mm2 using the key provided, and fixed in any
Auxiliary switches 2 x SPDT 6(3)A, AC 250V required position. Release of the locking
- Switching points 5° / 80° mechanism can be achieved manually or
Torque overridden by applying the supply
- Motor Min. 20 Nm
voltage.
- Spring Min. 20 Nm
Angle of rotation 95°
Output drive coupling Form-fit 14 mm double hexagon Testing.
Direction of rotation Selected by mounting L/R A test switch is incorporated in the ETR.
Running time
- Motor <60s
- Spring ~24s (@ tamb = 20°C)
Sound power level
- Motor max. 45 dB(A)
- Spring ~ 62 dB(A)
Position indication mechanical with pointer
Protection class III II
Degree of protection IP 54
Ambient temperature range
- Normal duty -30...+ 50° C
- Safety duty -30...+ 60° C (24h)
- Non-operating temperature -40...+ 60 °C
Humidity test To EN60335-1
EMC CE according 89/336/EEC and 92/31/EEC, 93/68/EEC
Low voltage directive CE according 73/23/EEC
Service life 25,000 cycles
Weight approx. 2‘800g approx. 3‘100g
mode 5 and 6 PTC regular on infodesk updated janu08.doc