Regulator and Control Valve Sizing
By
Hugh Masterson and Jim Mueller
Master Controls
March 13, 2019 2
What is a regulator?
HIGHER MAOP LOWER MAOP
A Regulator is a device that controls the flow of gas from a
higher pressure system to a lower pressure system while
attempting to maintain a constant pressure or flow.
Regulator Selection
o Select the correct regulator for the
application considering the following:
• Speed of response, i.e., boiler fuel
• Differential pressure
• Turndown = Max flow/min flow
• Noise
• Accuracy
• Self Operated
• Pilot Operated
• Control Valve
Selection Chart
Pilot-Operated
(Shaded Area)
Self Operated
“Farm Tap”
Self-Operated Rollout Diaphragm
HOUSE
SERVICE INDUSTRIAL
Regulator Orifice or Valve Size (Inches)
Self Operated Pressure Reducing Regulator
Loading Element
10 lbs force
Measuring Element
Restrictive Element
100psig 10 psig
High Low
Pressure Pressure
Factors to Consider
• Filter - pilot supply – always.
• Filter - entire station?
• Overpressure protection?
• Hydrates and/or freezing (Joule-
Thompson effect)? Adding a pilot gas
heater?
• Throttle plate selection (capacity and
type to prevent diaphragm erosion in
Sizing Tips high pressure cuts).
• Exit and downstream gas velocity.
Larger regulators and downstream pipe
diameters results in lower velocity.
Factors to Consider
• Pipeline turbulence caused by other
equipment (elbows, tee’s, valves, etc.)
that can affect sense lines.
• Sense lines should be 8 to 10 pipe
diameters down stream, 4 diameters
upstream of a tee or elbow.
• Diaphragm selection (chemical
compatibility, differential pressure
Sizing Tips rating, temperature, resistance to
abrasion).
• Solution versus cost assessment
• Single regulator or monitor regulator
set?
Noise
• Consider 1-stage vs. 2-stage
design to reduce noise levels
(2 stage has less noise).
• Use a drilled or stepped
drilled hole throttle plate to
help reduce noise.
• Increase size to lower the
Sizing Tips outlet velocity and reduce
noise levels.
• Increase pipe wall thickness
to reduce noise levels.
Capacity
– Optimal design should not
exceed 75% - 80% of maximum
capacity (capacity factor of 75%
- 80%) .
– Better to oversize than
undersize.
– Rangeability (turn down)
Sizing Tips » 50:1 – Slotted throttle plate
» 100:1 – Slotted throttle plate
» Greater than 100:1 – Stepped
drilled hole throttle plate
Design Considerations
o Minimum pressure
differential :
See Differential Chart
o Maximum pressure
differential :
Sizing Tips
800 psid (1000 psid for 1”)
Mooney Flowgrid Regulator
Pressure Reducing Application - Standby Monitor
Confidential
Sizing Conditions
o Max. Cv Condition o Maximum ∆P
Max. Flow (Q) ANSI Class, Regulator Specification
Min. Inlet Pressure (P1) Maximum control point, % Open
Max. Outlet Pressure (P2) Minimum control point, % Open
Max. Temperature (T) For Mooney regulators use
stepped drilled hole throttle
o Min. Cv Condition plates for Cg’s less than 4 to 5%
Min. Flow (Q) of the regulators capacity
Max. Inlet Pressure (P1)
Min. Outlet Pressure (P1) o Max Downstream Gas Velocity
Min. Temperature (T) Above ground ~100 fps
Below ground ~200 fps
o Max. Noise Condition
Max. Flow (Q) o Max Valve Exit Velocity
Max. Inlet Pressure (P1) 0.3 X Mach ~230 fps
Min. Outlet Pressure (P2)
Max. Temperature (T) o Control Valve Operating Range
Standard Becker; 10 - 93% open
Universal Gas Sizing Equation
P
Cg P1 Sin
520 3417
Q
GT C1 P1
Cg = gas sizing coefficient
Cv = liquid sizing coefficient
C1 = Cg/Cv
G = gas specific gravity (air = 1.0)
P1 = inlet pressure, psia
P2 = outlet pressure, psia
ΔP = pressure drop P1 – P2, psi
T = flow temperature, °R(460 + °F)
Follow these instructions.
Select the ValSpeQ vX.XX link above and save to a location on your hard drive.
DO NOT CLICK THE RUN BUTTON FROM THE DOWNLOAD DIALOG. CLICK ONLY THE SAVE BUTTON.
RUN ALL INSTALLS BY USING THE RIGHT CLICK “RUN AS ADMINISTRATOR” METHOD
After successful and complete save to the file system…
¨ If this edition has never been installed on the pc before, you will get prompted for registration information
below
o If prompted for Product Key, enter 60015410
o If prompted for Install key, leave this area blank, and hit next
o Enter all registration information
o If prompted to save registration file to desktop, do so.\
o If prompted to e-mail registration in, do so, copy
[email protected] on the resulting e-mail
that gets created by the installer.
o Hit back button and wait for the install key from me., if you hit finish, you will have to rerun the
installation when you receive the install key.
o When you receive the install key, enter the install key code, and hit next, the installation will
continue.
¨ Otherwise the install will not prompt and you can proceed normally.
Regulator
Sizing
Examples
Regulator Sizing Example 1
Flow Rate (Q) 20 – 300 MSCFH
Upstream Pressure Range P(1) 150 – 240 PSIG
Downstream Pressure P(2) 30
Inlet Gas Temp 60 deg F
Max Cv Case Min Cv Case Noise Case
Flow Rate (Q) MSCFH 300 20 300
Upstream Pressure (P1) 150 psig 240 psig 240 psig
Downstream Pressure (P2) 30 psig 30 psig 30 psig
Gas Temperature deg F 60 60 60
85 - 90 dBA Noise Requirement
Regulator Sizing Example 2
Flow Rate (Q) 4 – 30 MSCFH
Upstream Pressure Range P(1) 700 – 850 PSIG
Downstream Pressure P(2) 150
Inlet Gas Temp 60 deg F
Max Cv Case Min Cv Case Noise Case
Flow Rate (Q) MSCFH 30 4 30
Upstream Pressure (P1) 700 psig 850 psig 850 psig
Downstream Pressure (P2) 150 psig 150 psig 150 psig
Gas Temperature deg F 60 60 60
85 - 90 dBA Noise Requirement
Joule-Thomson Effect
When a highly compressed gas is allowed to escape / expand through a small opening, it absorbs
a great deal of energy from its surroundings, causing the surrounding temperature to drop. This
is the basis of refrigeration.
As a rule of thumb gas temperatures will drop ~ 7 Degrees F for every 100 psig in pressure drop.
Joule-Thomson Effect
Pilot Gas Heating
Pilot Gas Heating
Control Valve
Sizing
Examples
Control Valve Sizing Example 1
Flow Rate (Q) 25 – 300 MMSCFD
Upstream Pressure Range P(1) 950 – 1050 PSIG
Downstream Pressure P(2) 935
Inlet Gas Temp 60 deg F
Max Cv Case Min Cv Case Noise Case
Flow Rate (Q) MMSCFD 300 25 300
Upstream Pressure (P1) 950 psig 1050 psig 1050 psig
Downstream Pressure (P2) 935 psig 935 psig 935 psig
Gas Temperature deg F 60 60 60
85 - 90 dBA Noise Requirement
Control Valve Sizing Example 2
Flow Rate (Q) 50 – 440 MMSCFD
Upstream Pressure Range P(1) 900 – 1200 PSIG
Downstream Pressure P(2) 850
Inlet Gas Temp 60 deg F
Max Cv Case Min Cv Case Noise Case
Flow Rate (Q) MMSCFD 440 50 440
Upstream Pressure (P1) 900 psig 1200 psig 1200 psig
Downstream Pressure (P2) 850 psig 850 psig 850 psig
Gas Temperature deg F 60 60 60
85 - 90 dBA Noise Requirement
Filters and Filter/Dryers
Cold Gas Increases the potential for liquid
dropout
Joule-Thomson Effect
When a highly compressed gas is allowed to escape / expand through a small opening, it absorbs
a great deal of energy from its surroundings, causing the surrounding temperature to drop. This
is the basis of refrigeration.
As a rule of thumb gas temperatures will drop ~ 7 Degrees F for every 100 psig in pressure drop.
Filtering
Vertical Pipeline Heater
Horizontal Pipeline Heater
