Scribd
Upload
187 views1 page

Socket Weld Fittings: ASME B16.11-2009 (Revision of ASME B16.11-2005)

This document provides specifications for socket weld fittings according to ASME B16.11-2009. It lists nominal pipe sizes from 1/8 inch to 4 inches along with dimensions for elbows, tees, crosses and other fittings including bore diameter, socket depth, wall thickness and other physical characteristics. Tolerances are provided for minimum and average dimensions depending on the pressure class of 3000, 6000, or 9000.

Uploaded by

SIMON S. FLORES G.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
187 views1 page

Socket Weld Fittings: ASME B16.11-2009 (Revision of ASME B16.11-2005)

This document provides specifications for socket weld fittings according to ASME B16.11-2009. It lists nominal pipe sizes from 1/8 inch to 4 inches along with dimensions for elbows, tees, crosses and other fittings including bore diameter, socket depth, wall thickness and other physical characteristics. Tolerances are provided for minimum and average dimensions depending on the pressure class of 3000, 6000, or 9000.

Uploaded by

SIMON S. FLORES G.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Socket Weld Fittings

ASME B16.11-2009 (Revision of ASME B16.11-2005)

Socket Wall Thickness (2)Body Wall Thickness


Center to Bottom of Socket-A Socket Depth
Bore Dia. Of Fitting C G
Nom. 90° Elbows Bore D of
DN Pipe 45° Elbows Dia. Class Designation Class Designation Socket
Tees, Crosses
Size Class Designation Class Designation Class Designation 3000 6000 9000 3000 6000 9000 Min.
B J
3000 6000 9000 3000 6000 9000 3000 6000 9000 Ave. Min Ave. Min Ave. Min Min. Min. Min.
6 1/8” 11.0 11.0 8.0 8.0 10.8 6.9 4.0 3.18 3.18 3.96 3.43 2.41 3.15 9.5
8 1/4” 11.0 13.5 8.0 8.0 14.2 9.3 6.4 3.78 3.30 4.60 4.01 3.02 3.68 9.5
10 3/8” 13.5 15.5 8.0 11.0 17.6 12.6 9.2 4.01 3.50 5.03 4.37 3.20 4.01 9.5
15 1/2” 15.5 19.0 25.5 11.0 12.5 15.5 21.8 15.8 11.8 6.4 4.67 4.09 5.97 5.18 9.35 8.18 3.73 4.78 7.47 9.5
20 3/4” 19.0 22.5 28.5 13.0 14.0 19.0 27.2 21.0 15.6 11.1 4.90 4.27 6.96 6.04 9.78 8.56 3.91 5.56 7.82 12.5
25 1” 22.5 27.0 32.0 14.0 17.5 20.5 33.9 26.7 20.7 15.2 5.69 4.98 7.92 6.93 11.38 9.96 4.55 6.35 9.09 12.5
32 1-1/4” 27.0 32.0 35.0 17.5 20.5 22.5 42.7 35.1 29.5 22.8 6.07 5.28 7.92 6.93 12.14 10.62 4.85 6.35 9.70 12.5
40 1-1/2” 32.0 38.0 38.0 20.5 25.5 25.5 48.8 40.9 34.0 28.0 6.35 5.54 8.92 7.80 12.70 11.12 5.08 7.14 10.15 12.5
50 2” 38.0 41.0 54.0 25.5 28.5 28.5 61.2 52.5 42.9 38.2 6.93 6.04 10.92 9.50 13.84 12.12 5.54 8.74 11.07 16.0
65 2-1/2” 41.0 28.5 73.9 62.7 8.76 7.67 7.01 16.0
80 3” 57.0 32.0 89.8 78.0 9.52 8.30 7.62 16.0
100 4” 66.5 41.0 115.2 102.3 10.69 9.35 8.56 19.0
(1) Dimensions in Millimeters.
(2) Average of socket wall thickness around periphery shall be no less than listed values. The minimum values are permitted in localized areas.
(3) Upper and lower values for each size are the respective maximum and minimum dimensions.

You might also like