9.
Fault codes
9.1 Fault codes diagnosis version up to 204
ADM2 ADM2 Description Remedial action Pin
fault codes fault codes
(J1939) (k-line)
SPN/FMI
45/3 10003 decom- open circuit - check wiring 15/10
pression valve - check solenoid valve
MBR_KD
45/4 10004 decom- shorted to - check wiring 15/10
pression valve ground - check solenoid valve
MBR_KD
84/3 10103 vehicle open circuit - check wiring 15/03
speed - check parameter 08/01
signal C3
84/4 10104 vehicle shorted to - check wiring 15/03
speed ground
signal C3
84/14 10114 vehicle value not - check parameter 08/01 15/03
speed plausible
signal C3
91/0 10200 analog accelerator - restart accelerator pedal adjustment 21/11
accelerator pedal not routine
pedal adjusted - check wiring
- Limit value idle operation position:
5,0 V
- Limit value kickdown position: 4,9 V
91/2 10202 analog voltage not - Pedal unit exchange, if defective 21/11
accelerator plausible - check wiring
pedal - Limit value idle operation position:
5,0 V
- Limit value kickdown position: 4,9 V
91/3 10203 analog voltage too high - Pedal unit exchange, if defective 21/11
accelerator or shorted to - check wiring
pedal battery voltage - Limit value idle operation position:
5,0 V
- Limit value kickdown position: 4,9 V
91/4 10204 analog voltage too low - Pedal unit exchange, if defective 21/11
accelerator or - check wiring
pedal AFPS shorted to - Limit value idle operation position:
ground 5,0 V
- Limit value kickdown position: 4,9 V
98/0 10400 oil level oil level to high - Oil discharge with to strong PLD-MR
overstocking.
- remark: This problem can occur also
if in PLD-MR the false type of oil pan
were programmed.
ADM2 ADM2 Description Remedial action Pin
fault codes fault codes
(J1939) (k-line)
SPN/FMI
98/1 10401 oil level low oil level - refill oil PLD-MR
98/14 10414 oil level oil level too low - refill oil PLD-MR
- remark: This problem can occur also
if in PLD-MR the false type of oil pan
were programmed.
100/1 10501 oil pressure low oil pressure - check oil pump and oil circuit PLD-MR
sensor
100/14 10514 oil pressure oil pressure too - check oil pump and oil circuit. PLD-MR
sensor low
107/0 10800 air filter air pressure too - check wiring. 15/08
sensor high
107/3 10803 air filter open circuit - check wiring. 15/08
sensor
107/4 10804 air filter shorted to - check wiring. 15/08
sensor ground
110/0 10900 coolant high coolant - cooling-water level and cooling PLD-MR
temperature temperature circuit check.
110/14 10914 coolant coolant - cooling-water level and cooling PLD-MR
temperature temperature circuit check.
too high
111/1 11001 coolant low coolant - refill coolant 15/07
level level - check wiring
111/3 11003 coolant open circuit - check wiring 15/07
level - Voltage must be larger than 2,0 V.
111/4 11004 coolant shorted to - check wiring. 15/07
level ground
158/0 11100 terminal 15 over voltage - check battery voltage 21/02
(ignition) - check parameter 2/08
(24V/12V selection)
158/1 11101 terminal 15 under voltage - check battery voltage 21/02
(ignition) - check parameter 2/08
(24V/12V selection)
558/1 11701 idle switch Wiring idle - check wiring 21/12 and
(analog pedal) validation - Pedal unit exchange, if defective 21/13 or
switch GAS1 21/14
and GAS2
twisted or open
circuit at
potentiometer
ground FP-
ADM2 ADM2 Description Remedial action Pin
fault codes fault codes
(J1939) (k-line)
SPN/FMI
558/5 11705 idle switch both switches - check wiring 21/12 and
(analog pedal) open circuit - Pedal unit exchange, if defective 21/13
(GAS2 + GAS1
open)
558/12 11712 idle switch both switches - check wiring 21/12 and
(analog pedal) closed - Pedal unit exchange, if defective 21/13
(GAS2 + GAS1
closed)
599/12 11812 cruise control both switches - check wiring 18/04
switch closed - check cruise control switch and
CC+ and CC-
18/05
601/12 11912 cruise control both switches - check wiring 18/04
switch closed - check cruise control switch and
CC+ and CC-
18/05
620/3 12103 power supply voltage too high - supply voltage > 5,2 V. 21/09
analog pedal
(AFP+)
620/4 12104 power supply voltage too low - supply voltage < 4,8 V. 21/09
analog pedal
(AFP+)
625/2 12202 CAN link no com- - check wiring (engine CAN) -
ADM2 - MR munication with - check configuration:
MR
MR parameter (../..) and
ADM2 parameter 1/01
to be set to equal functionality
(0ne wire capability)
625/14 12214 CAN link one wire mode - check wiring (engine CAN) -
ADM2 - MR - check configuration:
MR parameter (../..) and
ADM2 parameter 1/01
to be set to equal functionality
(0ne wire capability)
629/12 12312 ADM2 internal - -
error
677/5 13305 output open circuit - check wiring 15/12
relay 1 - check relay 1
677/6 13306 output shorted - check wiring 15/12
relay 1 to ground - check relay 1
ADM2 ADM2 Description Remedial action Pin
fault codes fault codes
(J1939) (k-line)
SPN/FMI
730/0 13900 output grid heater: no - check wiring 15/09
relay 2 increasing
boost - check relay 2
temperature
after activation - check grid heater
730/1 13901 output grid heater: - check wiring 15/09
relay 2 relay
permanently - check relay 2
closed
730/2 13902 output grid heater: - check wiring 15/09
relay 2 relay
permanently - check relay 2
closed
730/3 13903 output voltage too high - check wiring 15/09
relay 2 or shorted to
battery voltage
730/4 13904 output voltage too low - check wiring 15/09
relay 2 or shorted - check relay 2
to ground
974/2 14202 remote supply voltage - limit values for the supply voltage of 18/17
pedal HFG out of range the HFG:
Minimum value: 4,8 V and
maximum value: 5,2 V.
974/3 14203 remote voltage too high - check wiring 18/18
pedal HFG or shorted to - check remote pedal
battery voltage
974/4 14204 remote voltage too low - check wiring 18/18
pedal HFG or shorted to - check remote pedal
ground
1004/3 14403 output open circuit - check wiring 18/01
relay 4 - check relay 4
1004/4 14404 output shorted - check wiring 18/01
relay 4 to ground - check relay 4
ADM2 ADM2 Description Remedial action Pin
fault codes fault codes
(J1939) (k-line)
SPN/FMI
1005/3 14503 output open circuit - check wiring. 15/05
PWM pedal
supply or
transmission
1005/4 14504 output shorted - check wiring. 15/05
PWM pedal to ground
supply or
transmission
1006/3 14603 exhaust brake open circuit - check wiring 15/06
valve MBR_BK - check exhaust brake valve
1006/4 14604 exhaust brake shorted - check wiring 15/06
valve MBR_BK to ground - check exxhaust brake valve
639/2 14902 J1939 CAN- CAN identifiers - PGN ETC1 was received only once
interface ETC#1 or and did not disappear.
ACC#1
missing
1015/1 15001 PWM no supply - check wiring 15/05
accelerator voltage
pedal
1015/2 15002 PWM both signals - check wiring
accelerator missing (GAS1 - Pins 21/13, 21/12, 15/05 , 21/14.
pedal and GAS2)
1015/3 15003 PWM signal GAS2, - check wiring
accelerator not available - Pins 21/13, 15/05 , 21/14.
pedal
1015/4 15004 PWM signal GAS1, - check wiring
accelerator not available - Pins 21/12, 15/05 , 21/14.
pedal
1015/5 15005 PWM accelerator - restart accelerator pedal adjustment -
accelerator pedal not routine
pedal adjusted
1015/6 15006 PWM idle position - restart accelerator pedal adjustment -
accelerator out of adjusted routine
pedal range
1015/7 15007 PWM accelerator - restart accelerator pedal adjustment -
accelerator pedal out of routine
pedal adjusted range
