Scribd
Upload
220 views1 page

Hydraulics Work Sheet: Well Data

This document contains a hydraulics work sheet used to calculate hydraulic parameters for drilling operations such as pump data, pressure losses throughout the system, nozzle selection, hydraulic horsepower at the bit, and more. Sections include information on the well, drill pipe, drill collars, pump specifications, pressure losses, nozzle selection, hydraulic calculations, and hole area. The goal is to determine the appropriate nozzle size, hydraulic horsepower applied to the bit, and efficiency of the system.

Uploaded by

Mohamed Elkumati
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
220 views1 page

Hydraulics Work Sheet: Well Data

This document contains a hydraulics work sheet used to calculate hydraulic parameters for drilling operations such as pump data, pressure losses throughout the system, nozzle selection, hydraulic horsepower at the bit, and more. Sections include information on the well, drill pipe, drill collars, pump specifications, pressure losses, nozzle selection, hydraulic calculations, and hole area. The goal is to determine the appropriate nozzle size, hydraulic horsepower applied to the bit, and efficiency of the system.

Uploaded by

Mohamed Elkumati
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

th

3901 S.W. 113 Street


Oklahoma City, OK 73173

Hydraulics Work Sheet


BIT SIZE TYPE

OPERATOR CONTRACTOR RIG NO DATE

WELL NAME NO. CO UNTY STATE

WELL DATA:

Hole Size from to Drill pipe size wt. t.j. length

Drill collar length OD Mud Min. annular velocity (drill pipe)

PUMP DATA:

Make Model SPM

Liner Size / Press. Rating / Oper. press. limit

1. Maximum operating pressure psi


Volumetric discharge ( Table 1 ) gal/stk
2. Circulation rate ( Table 2A or 2B ) gpm
3. Annular Velocity ( a ) Drill pipe (Table 3A) ft/min
( b ) Drill collars (Table 3B) ft/min
4. Surface equipment type ( Table 4 )
SYSTEM PRESSURE LOSSES:
5. Surface equipment ( Table 5 ) psi
6. Drill pipe bore ( Table 6 ): loss per 100 ft. x length X = psi
1000
7. Drill pipe annulus ( Table 7 ): loss per 100 ft. x length X = psi
1000
8. Drill collar bore ( Table 8 ): loss per 100 ft. x length X = psi
100
9. Drill collar annulus ( Table 9 ): loss per 100 ft. x length X = psi
100
9a. PDM/MWD pressure loss ( at 10 ppg) psi
10. System pressure loss: add lines 5 through 9a x mud wt. X = psi
10
( excluding nozzles) 10
11. Pressure available for nozzle TFA selection : line 1 minus line 10 x 10 X 10 = psi
mud wt.
JET NOZZLE FTA SELECTION:
12. Jet nozzle size ( Table 10 ) or TFA ( Table 12 ) 32nd
13. Pressure loss through jet nozzles TFA ( Table 10 ): pressure loss x mud wt. X = psi
10 10
14. Jet velocity ( Table 11, if nozzled bit ) ft/sec
15. Total pressure expenditure for system: ( add line 10 and line 13 ) psi

16. Hydraulic horsepower at bit: line 13 x line 2 X = HHP


1714 1714

17. Percent hydraulic horsepower at bit: line 13 x 100 X 100 = %


line 15
2 2
18. Area of hole:πD 3.14 X ( )2 = in
4
4
2
19. Hydraulic horsepower per square inch of hole: line 16 = HHP/in
line 18

You might also like