Huawei.H12-211.v2020-01-04.

q86
Exam Code: H12-211
Huawei Certified Datacom Associate-Huawei Networking Technology and
Exam Name:
Device (HCDA-HNTD)
Certification
Huawei
Provider:
Free Question
86
Number:
Version: v2020-01-04
# of views: 912
# of Questions
13428
views:
https://www.freecram.com/torrent/Huawei.H12-211.v2020-01-04.q86.html

NEW QUESTION: 1
A gateway must be configured for communication between a host and other hosts.
A. False
B. True
Answer: B (LEAVE A REPLY)

NEW QUESTION: 2
As shown in the figure, if the switch runs STP with default parameters, which of the following
ports will be elected as the designated port?

A. Port G0/0/2 of Switch A

NEW QUESTION: 3
Refer to the graphic. RTA is a DTE device connected to a Frame Relay switch, and uses dynamic
address mapping to establish the PVC. With regards to the configuration, which of the following
commands are not necessary? (Choose two).
A. [RTA-Serial1/0/1]ip address 172.16.1.1 24
B. [RTA-Serial1/0/1]fr interface-type dte
C. [RTA-Serial1/0/1]fr inarp
D. [RTA-Serial1/0/1]link-protocol FR
Answer: (SHOW ANSWER)

NEW QUESTION: 4
The administrator wishes to update the configuration file of an AR2200 router using a USB cable.
How can this be achieved? (Choose two)
A. The administrator should connect the USB cable between the terminal and the mini USB port
of the AR2200 router.
B. The administrator should connect the USB cable between the terminal and the USB port of the
AR2200 router.
C. The AR2200 router cannot support configuration updates through a USB cable.
D. The administrator should install the mini USB drivers on the terminal after connecting the USB.
Answer: A,D (LEAVE A REPLY)

NEW QUESTION: 5
When the link layer protocol Is ( ), OSPFV3 considers the network as a broadcast network.
A. PPP
B. ARP
C. Ethernet
D. HDLC
Answer: (SHOW ANSWER)

NEW QUESTION: 6
The following description of the Router ID in OSPF is incorrect (). (multiple choice)
A. The router ID must be specified by manual configuration.
B. The router IDs must be the same in the same area. The router IDs in different areas can be
different.
C. The router ID must be the IP address of an interface of the router.
D. The prerequisite for the normal operation of OSPF is that the router has a router I
Answer: (SHOW ANSWER)

NEW QUESTION: 7
On VRP platform, which of the following parameters can be used together with the "ping"
command to specify the source address of an echo request message?
A. S
B. A
C. D
D. N
Answer: B (LEAVE A REPLY)

NEW QUESTION: 8
After the administrator successfully logs in to the router through Telnet and finds that the IP
address of the interface of the router cannot be configured, the possible causes are ().
A. The Telnet terminal software used by the administrator prohibits the corresponding operation.
B. The authentication mode of the Telnet user is incorrectly configured.
C. SNMP parameter configuration error
D. The Telnet user level is incorrectly configured.
Answer: (SHOW ANSWER)

NEW QUESTION: 9
If AH and ESP are both required to protect data streams between IPsec peers, how many
Security Associations (SA) are required in total?
A. 4
B. 3
C. 1
D. 2
Answer: A (LEAVE A REPLY)

NEW QUESTION: 10
According to the default value of route preference on the VRP platform, which of the following
represent the correct sequence for direct route, static route, RIP and OSPF if they are listed from
high preference to low preference?
A. Direct, RIP, Static, OSPF
B. Direct, OSPF, RIP, Static
C. Direct, Static, RIP, OSPF
D. Direct, OSPF, Static, RIP
Answer: (SHOW ANSWER)

NEW QUESTION: 11
As shown in the broadcast network, OSPF runs on four routers and is in the same area and on
the same network segment. OSPF A DR and multiple BDRs will be automatically elected to
achieve better backup results.
A. Wrong
B. Yes
Answer: (SHOW ANSWER)

NEW QUESTION: 12
When using VRP, which of the following commands is used to configure the data link layer
encapsulation type of a serial interface as HDLC?
A. link-protocol ppp
B. encapsulation hdlc
C. hdlc enable
D. link-protocol hdlc
Answer: D (LEAVE A REPLY)

NEW QUESTION: 13
As shown in the figure, the R0 and RTB G0/0/1 interfaces are configured with IPV6 addresses of
different network prefixes, and the network administrator is on two routers.
Both run the OSPFv3 protocol and configure the OSPFv3 Router ID for each router. The correct
description is (). (many selected)

A. RTA cannot ping RTB

NEW QUESTION: 14
Two routers are connected via serial interfaces and the link-protocol is PPP, but the MRU of two
serial interface's are different, in PPP LCP negotiated stage, what will happen?
A. LCP negotiation will fail
B. Negotiation will use the larger value
C. Negotiation will use the smaller value
D. Negotiation will use 1500
Answer: C (LEAVE A REPLY)

NEW QUESTION: 15
After a fault occurs in the network, the administrator finds out that the configuration of a router has
been modified. What measures should the administrator take to avoid?
Avoid this happening again? (multiple choice)
A. The administrator should configure AAA to authenticate and authorize users who log in to the
device.
B. The administrator should configure all account login devices except the administrator to have a
privilege level of 0.
C. The administrator should configure the ACL to control only the administrator to log in to the
device.
D. The administrator should enable port-security on the management port of the route
Answer: A,B,C (LEAVE A REPLY)

NEW QUESTION: 16
If Host B also configured the IP address as "192.168.1.1/24", an IP address confict will occur.
What will happen as a result?
A. Host B will send an ICMP request to the destination with the configured IP address. If a reply is
received, the host will notify of an address conflict.
B. Host B will send a gratuitous ARP request to resolve the MAC address of the destination
192.168.1.1, for which Host A will reply.
C. Host A will ignore any received ARP request intended for destination 192.168.1.1.
D. Host A will send a gratuitous ARP request to resolve the MAC address of the destination
192.168.1.1, for which Host B will reply.
Answer: (SHOW ANSWER)
 Valid H12-211 Dumps shared by PrepAwayExam.com for Helping Passing H12-211 Exam!
PrepAwayExam.com now offer the newest H12-211 exam dumps, the PrepAwayExam.com
H12-211 exam questions have been updated and answers have been corrected get the
newest PrepAwayExam.com H12-211 dumps with Test Engine here:
https://www.prepawayexam.com/Huawei/braindumps.H12-211.ete.file.html (320 Q&As Dumps,
40%OFF Special Discount: freecram)

NEW QUESTION: 17
Which of the following are routing protocols? (multiple choice)
A. BGP
B. IPX
C. OSPF
D. IP
Answer: A,C (LEAVE A REPLY)

NEW QUESTION: 18
Which of the following OSPF versions is specific to IPv6?
A. OSPFv4
B. OSPFv1
C. OSPFv3
D. OSPFv2
Answer: C (LEAVE A REPLY)

NEW QUESTION: 19
Referring to the following topology and configuration, routers R1 and R2 are connected through a
Serial low-speed cable, and the data link layer uses PPP. When R1 and R2 When the Holdtimes
are inconsistent, ARP negotiation fails and communication cannot be performed.
A. Correct
B. Error
Answer: B (LEAVE A REPLY)

NEW QUESTION: 20
The VRP operating system commands are divided into four levels: access level, monitoring level,
configuration level, and management level. Can run various business configuration commands
but not Which level of operating file system?
A. Monitoring level
B. Management level
C. Configuration level
D. Access level
Answer: C (LEAVE A REPLY)

NEW QUESTION: 21
The Layer 2 Ethernet switch generates a MAC address table option based on the () packet
received by the port.
A. Destination MAC address
B. Destination IP address
C. Source MAC address
D. Source IP address
Answer: C (LEAVE A REPLY)

NEW QUESTION: 22
You can use the preference preference to configure the priority value of a RIP route or the
command in the RIP process of the Huawei device.
After specifying a routing policy, set the priority value for the specific route that meets the
conditions.
A. Error
B. Correct
Answer: (SHOW ANSWER)

NEW QUESTION: 23
On the VRP platform, the order of the default protocol priorities of direct route, static route, RIP,
and OSPF is ().
A. Direct route, OSPF, static route, RIP
B. Direct routing, RIP, static routing, OSPF
C. Direct routing, OSPF, RIP, static routing
D. Direct route, static route, RIP, OSPF
Answer: A (LEAVE A REPLY)

NEW QUESTION: 24
Two authentication domains "Area1" and "Area2" are configured on the authentication server. If
the user uses the correct username "huawei" and the password is used.
The code "hello" is authenticated, and which authentication domain is this user assigned to?
A. Authentication domain "Area1"
B. Authentication domain "Area2"
C. Authentication domain "default domain"
D. Authentication domain "default_admin domain"
Answer: (SHOW ANSWER)

NEW QUESTION: 25
According to the command shown above, the correct one in the following description is ().
(multiple choice)
[Huawei-GigabitEthernet0/0/1]port link-type access
[Huawei-GigabitEthernet0/0/1]port default vlan 10
[Huawei-GigabitEthernet0/0/2]port link-type trunk
[Huawei-GigabitEthernet0/0/2]port trunk allow-pass vlan 10
A. The PVID of GigabitEthernet0/0/2 is 10
B. The PVID of port GigabitEthernet 0/0/1 is 1.
C. The PVID of port GigabitEthernet 0/0/1 is 10.
D. The PVID of the GigabitEthernet0/0/2 port is 1.
Answer: C,D (LEAVE A REPLY)

NEW QUESTION: 26
On the VRP platform, which of the following commands is used to configure the Router ID of a
router as
1.1.1.1?
A. [Huawei]router-id 1.1.1.1
B. [Huawei]router id 1.1.1.1
C. [Huawei]router id 1.1.1.1 255.255.255.255
D. <Huawei>router id 1.1.1.1
Answer: (SHOW ANSWER)

NEW QUESTION: 27
What versions of SNMP are supported by eSight? (multiple choice)
A. SNMPv2c
B. SNMPv3
C. SNMPv2
D. SNMPv1
Answer: (SHOW ANSWER)

NEW QUESTION: 28
When the routers are running in the same OSPF area, the description of their LSDB and routing
table is correct ().
(multiple choice)
A. The routing table of each router is different.
B. The routing tables obtained by all routers are the same.
C. The link state database obtained by all routers is the same
D. The link state database obtained by each router is different.
Answer: A,C (LEAVE A REPLY)

NEW QUESTION: 29
What command can I type in system view to switch to user view?
A. quit
B. router
C. system-view
D. user-view
Answer: A (LEAVE A REPLY)

NEW QUESTION: 30
<Huawei>display startup
MainBoard:
Startup system software: sd1:/ar2220-v200r003c00spc200.cc
Next startup system software: sd1:/ar2220-v200r003c00spc200.cc
Backup system software for next startup: null
Startup saved-configuration file: null
Next startup saved-configuration file: null
Startup license file: null
Next startup license file: null
Startup patch package: null
Next startup patch package: null
Startup voice-files: null
Next startup voice-files: null
Refer to the display output. Which statement is false?
A. The current startup system software is ar2220-v200r003c00spc200.cc
B. The next startup system software cannot be changed.
C. The current configuration file has not been saved.
D. The next startup system software can be changed by using the "startup system software
<startup-softwarename>.cc" command.
Answer: B (LEAVE A REPLY)

NEW QUESTION: 31
An existing switch is directly connected to the designated port of the peer device through a port,
but the port does not forward any packets but can be connected.
Receive a BPDU to listen for network changes, then the role of the port should be ().
A. Alternate port
B. Root port
C. Disable port
D. Designated port
Answer: (SHOW ANSWER)

Valid H12-211 Dumps shared by PrepAwayExam.com for Helping Passing H12-211 Exam!
PrepAwayExam.com now offer the newest H12-211 exam dumps, the PrepAwayExam.com
H12-211 exam questions have been updated and answers have been corrected get the
newest PrepAwayExam.com H12-211 dumps with Test Engine here:
https://www.prepawayexam.com/Huawei/braindumps.H12-211.ete.file.html (320 Q&As Dumps,
40%OFF Special Discount: freecram)

NEW QUESTION: 32
Refer to the graphic. RTA is a PPPoE client, and following transmission of PADI, Server A
responds with PADO packets to RTA. Which distribution method is used for sending PADO
packets?
A. multicast
B. unicast
C. broadcast
D. anycast
Answer: (SHOW ANSWER)

NEW QUESTION: 33
The subnet mask of a network segment 150.25.0.0 is 255.255.224.0, then () is the valid host
address in the network segment. (multiple choice)
A. 150.25.2.24
B. 150.25.1.255
C. 150.15.3.30
D. 150.25.0.0
Answer: (SHOW ANSWER)

NEW QUESTION: 34
Which of the following statements regarding the DR in an OSPF network are correct? (Choose
two)
A. A DR must be elected among the routers through the negotiations that are defined by OSPF
protocol.
B. There must be at least one DR in an OSPF area.
C. Only NBMA or Broadcast networks need to elect DR
D. Only the router with highest priority will be elected as DR.
Answer: A,C (LEAVE A REPLY)

NEW QUESTION: 35
In the following description of eSight, the error is ().
A. eSight supports WLAN device management and hotspot coverage monitoring
B. eSight supports configuration file backup and traffic analysis.
C. eSight can only manage Huawei network devices.
D. eSight can be used to monitor and manage enterprise networks
Answer: C (LEAVE A REPLY)

NEW QUESTION: 36
The description of the above display information is correct ().
[R1]display interface g0/0/0
GigabitEthernet0/0/0 current state:Administratively DOWN
Line protocol current state:DOWN
A. GigabitEthernet0/0/0 interface was manually closed by the administrator.c
B. GigabitEthernet0/0/0 interface is connected with a wrong cable.
C. GigabitEthernet0/0/0 interface is not configured with an IP address.
D. GigabitEthernet0/0/0 interface does not have dynamic routing protocol enabled.
Answer: (SHOW ANSWER)

NEW QUESTION: 37
Refer to the graphic. The link between RTA and RTB is encapsulated using PPP. The IP
addresses of serial
1/0/1 of RTA and serial 1/0/1 of RTB are in different network segments. Which following is
correct? (Choose two)
A. The route entry 10.1.1.2/32 exists in the routing-table of RTA
B. RTA cannot ping 10.1.1.2
C. RTA can ping 10.1.1.2 successfully
D. The route entry 10.1.1.0/24 exists in the routing-table of RTA
Answer: (SHOW ANSWER)

NEW QUESTION: 38
When two OSPF routers form a TWO WAY-neighbor relationship, the LSDB has completed
synchronization, but the SPF algorithm has not been run.
A. Yes
B. Wrong
Answer: (SHOW ANSWER)

NEW QUESTION: 39
The network structure and OSPF partition are shown in the figure. In addition to R1, routers R2,
R3 and R4 are OSPF ABR routers.
A. Correct
B. Error
Answer: B (LEAVE A REPLY)

NEW QUESTION: 40
How many probe packets are sent for each TTL value by default when "tracert" is used to detect
the path along which packet is sent from source to destination?
A. 6
B. 3
C. 8
D. 4
Answer: B (LEAVE A REPLY)

NEW QUESTION: 41
As shown in the figure, the administrator configured the following command on the RTA, and the
correct description is (). (multiple choice)
[RTA-Serial0/0/1] rip output
[RTA-rip-1]silent-interface s0/0/1
A. RTA neighbor information does not include RTB
B. RTB neighbor information does not include RTA
C. RTB can still learn the routing information published by RT
D. RTA can still learn the routing information published by RTB.
Answer: (SHOW ANSWER)

NEW QUESTION: 42
For project cutover, backup or adjustment of configuration files are not required during VRP
upgrade, because lost files can be found in the recycle bin.
A. True
B. False
Answer: (SHOW ANSWER)

NEW QUESTION: 43
Which of the following commands can be used to check whether OSPF has correctly established
neighbor relationships?
A. display ospf interface
B. display ospf brief
C. display ospf neighbor
D. display ospf peer
Answer: D (LEAVE A REPLY)

NEW QUESTION: 44
UDP is connectionless oriented, which of the following must be used in order to ensure reliability?
A. Network Layer Protocol
B. Application Layer Protocol
C. Internet Protocol
D. Transmission Control Protocol
Answer: B (LEAVE A REPLY)

NEW QUESTION: 45
What is the length of the Ethernet_II frame that contains the Ethernet header?
A. 46-1500B
B. 64-1518B
C. 64-1500B
D. 60-1560B
Answer: B (LEAVE A REPLY)

NEW QUESTION: 46
A serial interface of a Huawei router currently using HDLC needs to assign PPP as the
encapsulation protocol.
Which of the following commands is required to be configured at the serial interface view?
A. encapsulation ppp
B. link-protocol ppp
C. address ppp
D. enable ppp
Answer: B (LEAVE A REPLY)

Valid H12-211 Dumps shared by PrepAwayExam.com for Helping Passing H12-211 Exam!
PrepAwayExam.com now offer the newest H12-211 exam dumps, the PrepAwayExam.com
H12-211 exam questions have been updated and answers have been corrected get the
newest PrepAwayExam.com H12-211 dumps with Test Engine here:
https://www.prepawayexam.com/Huawei/braindumps.H12-211.ete.file.html (320 Q&As Dumps,
40%OFF Special Discount: freecram)

NEW QUESTION: 47
Regarding the commands used to detect IP network connectivity, the following statements are
incorrect ().
(multiple choice)
A. ping 127.0.0.2, this command is used to check whether the host's network cable is plugged in.
B. The ping command can be used to detect the connectivity of the host to the local gateway.
C. The ipconfig/release command can be used to detect the connectivity of the host to the local
gateway.
D. ping 127.0.0.1, this command is used to check whether the network cable of the host is
plugged in.
Answer: A,C,D (LEAVE A REPLY)

NEW QUESTION: 48
In standard STP mode, which of the following non-root switches forwards the TC set BPDU
generated by the root switch?
A. Backup port
B. Designated port
C. Provisioning port
D. Root port
Answer: B (LEAVE A REPLY)

NEW QUESTION: 49
The STP switch sends BPDUs. The correct statement about BPDU is (). (multiple choice)
A. The Control field value of the BPDU frame is 3.
B. BPDU is a frame using the Etherent II standard
C. The destination MAC address of the BPDU frame is the broadcast address.
D. BPDU is a frame using the IEEE802.3 standard
Answer: (SHOW ANSWER)

NEW QUESTION: 50
A client failed to transfer a file to the FTP server, but found the IP connectivity was without
problem. The client assumed that the problem was with the port configuration. The blocking of
which ports would likely cause this problem? (Choose two)
A. 20
B. 80
C. 21
D. 50649
Answer: A,C (LEAVE A REPLY)

NEW QUESTION: 51
When using VRP, which of the following commands is used to configure the PPP authentication
method as PAP?
A. ppp authentication-mode pap
B. ppp authentication-pap
C. ppp pap
D. ppp pap-authentication
Answer: (SHOW ANSWER)

NEW QUESTION: 52
If the transport-layer protocol is UDP, the value of the "Protocol" field at the network layer is 6.
A. True
B. False
Answer: (SHOW ANSWER)

NEW QUESTION: 53
When STP is running on Huawei Sx7 series switches, the priority of the switch is () by default.
A. 4096
B. 32768
C. 16384
D. 8192
Answer: (SHOW ANSWER)

NEW QUESTION: 54
Which of the following parameters must be specified when configuring static mapping for Frame
Relay network? (Choose two)
A. Local network layer protocol address
B. Remote DLCI
C. Remote network layer protocol address
D. Local DLCI
Answer: C,D (LEAVE A REPLY)

NEW QUESTION: 55
What types of networks are supported by the OSPF protocol? (multiple choice)
A. Point-to-Multipoint
B. Point-to-Point
C. Non-Broadcast Multi-Access
D. Broadcast
Answer: (SHOW ANSWER)

NEW QUESTION: 56
PPP is more secure and reliable than HDLC because PPP supports (). (multiple choice)
A. MD5
B. SSH
C. CHAP
D. PAP
Answer: (SHOW ANSWER)

NEW QUESTION: 57
NAPT allows multiple private IP addresses to be mapped to the same public IP address through
different port numbers. The following information about the port number in NAPT Description The
correct one is ().
A. Need to use ACL to assign port number
B. No need to do any configuration about the port number
C. You must manually configure the mapping between port numbers and private addresses.
D. Only need to configure the range of port numbers
Answer: (SHOW ANSWER)

NEW QUESTION: 58
Which of the following commands can be used to display mapping relationship between network
address and DLCI?
A. display fr brief
B. display fr interface
C. display fr map-info
D. display fr
Answer: C (LEAVE A REPLY)

NEW QUESTION: 59
The following is a mistake in the priority of static routes in Huawei devices
A. The static router priority value ranges from 0 255
B. The priority value of the static route is 255, indicating that the route is unavailable.
C. The priority of static routes is divided into internal priority and external priority. Administrators
can modify external priority.
D. The default value of static router priority is 60.
Answer: A (LEAVE A REPLY)

NEW QUESTION: 60
On the network shown in the figure, all routers run OSPF and the cost value is marked above the
link. What is the cost value of the route to 10.0.0.0/8 in the routing table of RA?

A. 20
B. 100
C. 70
D. 60
Answer: D (LEAVE A REPLY)

NEW QUESTION: 61
After the host obtains the IP address from DHCP server A and restarts, what kind of message will
the following message be sent to DHCP server A?
A. DHCP ACK
B. DHCP OFFER
C. DHCP DISCOVER
D. DHCP REQUEST
Answer: D (LEAVE A REPLY)

Valid H12-211 Dumps shared by PrepAwayExam.com for Helping Passing H12-211 Exam!
PrepAwayExam.com now offer the newest H12-211 exam dumps, the PrepAwayExam.com
H12-211 exam questions have been updated and answers have been corrected get the
newest PrepAwayExam.com H12-211 dumps with Test Engine here:
https://www.prepawayexam.com/Huawei/braindumps.H12-211.ete.file.html (320 Q&As Dumps,
40%OFF Special Discount: freecram)

NEW QUESTION: 62
In a small network suppporting IPv6, a network administrator wishes implement RIPng. Which of
the following commands should be used to enable this protocol?
A. [RTA]ripng 1 enable
B. [RTA-ripng-1]ripng 1 enable
C. <RTA>ripng 1 enable
D. [RTA-GigabitEthernet0/0/0]ripng 1 enable
Answer: D (LEAVE A REPLY)

NEW QUESTION: 63
Which of the following statements about a designated port working in RIPv2 multicast mode are
true?
(Choose three)
A. The port does not receive RIPv2 broadcast packets.
B. The port receives only RIPv1 multicast packets.
C. The port does not receive RIPv1 broadcast packets.
D. The port receives only RIPv2 multicast packets.
Answer: A,C,D (LEAVE A REPLY)

NEW QUESTION: 64
Referring to the configuration of the one-arm route in the following figure, it can be judged that
even if the ARP proxy is not enabled on the sub-interface of R1, between the administrative
department and the finance department Can also visit each other.
A. Wrong
B. Yes
Answer: A (LEAVE A REPLY)

NEW QUESTION: 65
An administrator wishes to configure a floating static route. In order to successfully achieve this,
which operation should be performed?
A. The administrator is required to configure a different costs metric for the primary static route
and floating static route.
B. The administrator is required to configure a different preference values for the primary static
route and floating static route.
C. The administrator is only required to configure two static routes.
D. The administrator is required to configure deferent route tags for the primary static route and
floating static route.
Answer: B (LEAVE A REPLY)

NEW QUESTION: 66
All interfaces on a router belong to the same broadcast domain.
A. False
B. True
Answer: A (LEAVE A REPLY)

NEW QUESTION: 67
As shown in the figure, the correct description about this network topology is ().

A. There are 6 broadcast domains in this network

NEW QUESTION: 68
Which of the following VRP commands can be used to enter area 0 view? (Choose two)
A. [Huawei-ospf-1]area 0
B. [Huawei-ospf-1]area 0.0.0.0
C. [Huawei]ospf area 0
D. [Huawei-ospf-1]area 0 enable
Answer: (SHOW ANSWER)
NEW QUESTION: 69
As shown in the figure, there is a web server in the private network that needs to provide more
HTTP services to the public network users, so the network administrator needs to be at the
gateway.
Configure NAT on the router RTA to meet the requirements. The correct configuration to meet the
requirements in the following configurations is ().

A. [RTA-Gigabitethernet0/0/1]] nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1
8080
B. [RTA-Gigabitethernet0/0/1] nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1
8080
C. [RTA-Serial1/0/1] nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
D. [RTA-Serial1/0/1] nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
Answer: (SHOW ANSWER)

NEW QUESTION: 70
The following static route configuration is correct (). (multiple choice)
A. ip route-static 129.1.0.0 16 serial 0
B. ip route-static 129.1.0.0 255.255.0.0 10.0.0.2
C. ip route-static 10.0.0.2 16 129.1.0.0
D. ip route-static 129.1.0.0 16 10.0.0.2
Answer: A,B,D (LEAVE A REPLY)

NEW QUESTION: 71
When using Telnet to log in to the router, which authentication methods can I choose? (choose 2
answers)
A. password authentication
B. MD5 ciphertext authentication
C. Not certified
D. AAA local certification
Answer: A,D (LEAVE A REPLY)

NEW QUESTION: 72
What benefits does port aggregation yield? (Choose three)
A. Improves network reliability
B. Improves link bandwidth
C. Implements load sharing
D. Facilitates data copy for analysis
Answer: A,B,C (LEAVE A REPLY)

NEW QUESTION: 73
After deploying a DHCP server on the network, the administrator finds that some hosts have
obtained the address specified by the DHCP server.
What are the possible reasons? (multiple choice)
A. Some hosts cannot communicate properly with the DHCP server. These host client systems
automatically generate addresses in the range of 127.254.0.0.
B. There is another DHCP server in the network that is more efficient.
C. The address pool of the DHCP server has been completely allocated.
D. Some hosts cannot communicate properly with the DHCP server. These host client systems
automatically generate addresses in the range of 169.254.0.0.
Answer: B,C,D (LEAVE A REPLY)

NEW QUESTION: 74
The Tracert diagnostic tool records the () of each ICMP TTL timeout message, so that the user
can be provided with the message to reach the destination.
IP address.
A. Source port
B. Destination port
C. Source IP address
D. Destination IP address
Answer: C (LEAVE A REPLY)

NEW QUESTION: 75
Which of the following commands is used to enable dynamic address mapping protocol in the
interface encapsulated with Frame Relay?
A. reverse-arp
B. fr reverse-arp
C. inverse-arp
D. fr inarp
Answer: D (LEAVE A REPLY)

NEW QUESTION: 76
Refer to the graphic. RTA and RTB are running RIPv1. RTA has advertised 10.0.0.0 and
192.168.1.0 to the RIP network. Which routes will exist in the IP routing table of RTB? (Choose
two)
A. 192.168.1.1/32
B. 10.1.12.1/32
C. 192.168.1.0/24
D. 10.0.0.0/8
Answer: B,C (LEAVE A REPLY)

Valid H12-211 Dumps shared by PrepAwayExam.com for Helping Passing H12-211 Exam!
PrepAwayExam.com now offer the newest H12-211 exam dumps, the PrepAwayExam.com
H12-211 exam questions have been updated and answers have been corrected get the
newest PrepAwayExam.com H12-211 dumps with Test Engine here:
https://www.prepawayexam.com/Huawei/braindumps.H12-211.ete.file.html (320 Q&As Dumps,
40%OFF Special Discount: freecram)

NEW QUESTION: 77
After an RSTP-enabled switch receives the BPOUs with the TC bit set, the MAC addresses
learned by all the ports are cleared.
A. False
B. True
Answer: B (LEAVE A REPLY)

NEW QUESTION: 78
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If you perform
configurations when Auto-Config is running, the DHCP, routing, DNS, and VTY configurations will
be lost.
Do you want to stop Auto-Config? [y/n]:
Refer to the output. When the administrator first starts the router, a system notice is displayed,
however after rebooting this router, the notice disappeared. What is the reason for this? (Choose
two)
A. This notice only appears during the very first device startup.
B. The administrator selected 'y' and saved the configuration.
C. The administrator selected 'n' and did not save the configuration
D. The administrator has configured the device and saved the configuration, causing the notice to
disappear.
Answer: B,D (LEAVE A REPLY)

NEW QUESTION: 79
[RTA]aaa
[RTA-aaa]domain huawei
[RTA-aaa-domain-huawei]authentication-scheme au1
[RTA-aaa-domain-huawei]authentication-scheme au2
The network administrator performs the above configuration on the Huawei router RTA. If a user
needs to be authenticated in the authentication domain "huawei", the following is true.
The correct description is ().
A. Will use the "authentication-scheme au2" certification
B. Will use the "authentication-scheme au1" certification
C. will use the "authentication-scheme au1" certification, if "au1" is deleted, will use "au2"
D. will use the "authentication-scheme au2" certification, if "au2" is deleted, will use "au1
Answer: A (LEAVE A REPLY)

NEW QUESTION: 80
Which of the following formats represent an accurate condensing of the IPv6 address
2031:0000:720C:0000:0000:09E0:839A:130B? (Choose two).
A. 2031::720C::9E0:839A:130B
B. 2031:0:720C:0:0:9E:839A:130B
C. 2031:0:720C::9E0:839A:130B
D. 2031:0:720C:0:0:9E0:839A:130B
Answer: (SHOW ANSWER)

NEW QUESTION: 81
Which of the following commands is used to enter the system-view from the user view on a
Huawei router?
A. interface system
B. enable
C. configure terminal
D. system-view
Answer: D (LEAVE A REPLY)

NEW QUESTION: 82
An administrator discovered he/she was unable to use TFTP to transfer files to the router. Which
of the following describes the likely reason for this?
A. TCP port 69 of the server had been blocked.
B. UDP port 69 of the server had been blocked.
C. The TFTP service had been disabled on the router.
D. The username and password had been modified.
Answer: B (LEAVE A REPLY)

NEW QUESTION: 83
Which of the following commands can be used to view the current configurations on a Huawei
router?
A. display current-configuration
B. show startup-configuration
C. display saved-configuration
D. view saved-configuration
Answer: A (LEAVE A REPLY)

NEW QUESTION: 84
Which of the following statements are correct about NAT? (Choose three)
A. NAT provides an effective way to solve the problem of insufficient IP addresses.
B. NAT is used for translation between private and public network addresss.
C. When hosts inside a private network access the outside network, NAT is not required.
D. NAT is the abbreviation for "Network Address Translation"
Answer: (SHOW ANSWER)

NEW QUESTION: 85
Which of the following statements about router IDs are true? (Choose two)
A. A router ID is expressed in a 32-bit dotted decimal format.
B. The routers contained in the same LSDB have the same router ID.
C. Two routers in different OSPF areas can have the same router ID.
D. Each router in an OSPF network must have a unique router ID.
Answer: (SHOW ANSWER)

NEW QUESTION: 86
The correct statement about free ARP is (multiple choice)
A. By sending a free ARP, you can confirm whether the IP address has a conflict.
B. The format of the free ARP packet is the same as that of the normal ARP request packet.
C. The format of the free ARP packet is the same as that of the normal ARP reply packet.
D. Free ARP can help update old IP address information
Answer: A,B (LEAVE A REPLY)

Valid H12-211 Dumps shared by PrepAwayExam.com for Helping Passing H12-211 Exam!
PrepAwayExam.com now offer the newest H12-211 exam dumps, the PrepAwayExam.com
H12-211 exam questions have been updated and answers have been corrected get the
newest PrepAwayExam.com H12-211 dumps with Test Engine here:
https://www.prepawayexam.com/Huawei/braindumps.H12-211.ete.file.html (320 Q&As Dumps,
40%OFF Special Discount: freecram)