Scribd
Upload
47 views

Code For IoT For ESP8266

This code summarizes an Arduino and NodeMCU code for monitoring energy consumption. The Arduino code measures current using an ACS712 sensor, calculates power and energy consumed over time, and sends the energy reading to serial. The NodeMCU code connects to WiFi, subscribes to the Arduino serial to get energy readings, calculates the energy bill amount, and publishes the power and bill readings to an Adafruit MQTT feed. It will publish the bill amount multiple times if it equals a certain value.

Uploaded by

Shirly Salih
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
47 views

Code For IoT For ESP8266

This code summarizes an Arduino and NodeMCU code for monitoring energy consumption. The Arduino code measures current using an ACS712 sensor, calculates power and energy consumed over time, and sends the energy reading to serial. The NodeMCU code connects to WiFi, subscribes to the Arduino serial to get energy readings, calculates the energy bill amount, and publishes the power and bill readings to an Adafruit MQTT feed. It will publish the bill amount multiple times if it equals a certain value.

Uploaded by

Shirly Salih
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Code For Arduino 

#include "ACS712.h"
char watt[5];
ACS712 sensor(ACS712_30A, A0);
unsigned long last_time =0;
unsigned long current_time =0;
float Wh =0 ;  
void setup() {
  Serial.begin(115200);
  sensor.calibrate();
}

void loop() {
  float V = 230;
  float I = sensor.getCurrentAC();
// Serial.println(I);
  float P = V * I;
  last_time = current_time;
  current_time = millis();    
  Wh = Wh+  P *(( current_time -last_time) /3600000.0) ; 
   dtostrf(Wh, 4, 2, watt);        
Serial.write(watt);
  delay(10000);
}

Code For NodeMCU

#include <ESP8266WiFi.h>
#include "Adafruit_MQTT.h"
#include "Adafruit_MQTT_Client.h"
#define WLAN_SSID       "a*************"
#define WLAN_PASS       "*******************"
char watt[5];
#define AIO_SERVER      "io.adafruit.com"
#define AIO_SERVERPORT  1883                   
#define AIO_USERNAME    "rjrishabh"
#define AIO_KEY         "***********************"

WiFiClient client;
int bill_amount = 0;   
unsigned int energyTariff = 8.0; 
Adafruit_MQTT_Client mqtt(&client, AIO_SERVER, AIO_SERVERPORT, AIO_USERNAME,
AIO_KEY);
Adafruit_MQTT_Publish Power = Adafruit_MQTT_Publish(&mqtt, AIO_USERNAME "/feeds/Power");
Adafruit_MQTT_Publish bill = Adafruit_MQTT_Publish(&mqtt, AIO_USERNAME "/feeds/bill");
void MQTT_connect();

void setup() {
  Serial.begin(115200);
  delay(10);
  Serial.println(F("Adafruit MQTT demo"));

  // Connect to WiFi access point.


  Serial.println(); Serial.println();
  Serial.print("Connecting to ");
  Serial.println(WLAN_SSID);

  WiFi.begin(WLAN_SSID, WLAN_PASS);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
 }
  Serial.println();

  Serial.println("WiFi connected");
  Serial.println("IP address: "); Serial.println(WiFi.localIP());
}

void loop() {
  // Ensure the connection to the MQTT server is alive (this will make the first
  // connection and automatically reconnect when disconnected).  See the MQTT_connect
  // function definition further below.
  MQTT_connect();

 int i=0;
 float watt1;
 if(Serial.available() > 0 ){
   delay(100); //allows all serial sent to be received together
    while(Serial.available() && i<5) {
     watt[i++] = Serial.read();
  }
    watt[i++]='\0';
 }

 watt1 = atof(watt);
  bill_amount = watt1 * (energyTariff/1000);      // 1unit = 1kwH
  Serial.print(F("\nSending Power val "));
  Serial.println(watt1);
  Serial.print("...");

  if (! Power.publish(watt1)) {
    Serial.println(F("Failed"));
  } else {
    Serial.println(F("OK!"));
 }

   if (! bill.publish(bill_amount)) {
    Serial.println(F("Failed"));
  } else {
    Serial.println(F("OK!"));
 }

if (bill_amount==4){
for (int i =0; i<=2; i++)
{
  bill.publish(bill_amount);
delay(5000);
}
bill_amount =6;
}
  
delay(5000);
}

// Function to connect and reconnect as necessary to the MQTT server.


// Should be called in the loop function and it will take care if connecting.
void MQTT_connect() {
  int8_t ret;
  // Stop if already connected.
  if (mqtt.connected()) {
    return;
 }

  Serial.print("Connecting to MQTT... ");

  uint8_t retries = 3;
  while ((ret = mqtt.connect()) != 0) { // connect will return 0 for connected
       Serial.println(mqtt.connectErrorString(ret));
       Serial.println("Retrying MQTT connection in 5 seconds...");
       mqtt.disconnect();
       delay(5000);  // wait 5 seconds
       retries--;
       if (retries == 0) {
         // basically die and wait for WDT to reset me
         while (1);
       }
 }
  Serial.println("MQTT Connected!");
}

You might also like