PARVEEN
HYDRAULIC DISCONNECT
TECHNICAL MANUAL
TABLES OF CONTENTS
1.0 DESCRIPTION
2.0 BILL OF MATERIAL
3.0 ASSEMBLY DRAWING
4.0 DISASSEMBLY PROCEDURES
5.0 ASSEMBLY PROCEDURES
PARVEEN
HYDRAULIC DISCONNECT
TECHNICAL MANUAL
1.0 DESCRIPTION:-
THE PARVEEN HYDRAULIC DISCONNECT ALLOWS THE TOOLSTRING TO DETACH
AT A PREDETERMINED POINT VIA THE DEPLOYMENT OF A SUITABLE DROP/TRIP
BALL THROUGH THE COILED TUBING.THE DROP BALL LOCATES ON A PISTON
SLEEVE CREATING SUFFICIENT BACK PRESSURE TO SHEAR THE PINS AND
DISCONNECT THE TOOL. ALL PISTON SLEEVES AND DROP BALLS ARE RETURNED
TO SURFACE LEAVING A STANDARD ‘GS’ INTERNAL FISH NECK FOR RETRIEVAL
PURPOSES.
FEATURES:-
• SEALED TO ALLOW PRESSURE OPERATIONS.
• ADJUSTABLE BALL SEAT I.D.
• TRANSMITS HIGH TORQUE LOADS.
• HIGH TENSILE STRENGTH RATINGS.
• INTERNAL FISHING NECK FOR EASY WASHING AND RE-ENTRY.
• COLLET STYLE LATCH.
PARVEEN
HYDRAULIC DISCONNECT
TECHNICAL MANUAL
PARVEEN INDUSTRIES PVT. LTD.
(MUMBAI) INDIA
BILL OF MATERIAL
DATE : 07/01/2010 REV: 0 PAGE 1 OF 1
HYDRAULIC DISCONNECT-1.11/16" OD
ASSY. PART No: 278-16819-00
ITEM NO. QTY. PART NO. REV DESCRIPTION
1 1 278-16819-01 0 TOP SUB (1.0" AMMT)
2 1 49126 0 O-RING
3 1 278-168-02 0 BODY
4 1 140-063-00 0 5/8" BALL
5 1 50209 0 O-RING
6 1 278-175-03 0 PISTON
7 1 50121 0 O-RING
8 2 50113 0 O-RING
9 4 142-256-01 0 SHEAR SCREW
10 1 278-16819-04 0 BOTTOM SUB (1.0" AMMT)
PARVEEN
HYDRAULIC DISCONNECT
TECHNICAL MANUAL
PARVEEN INDUSTRIES PVT. LTD.
(MUMBAI) INDIA
BILL OF MATERIAL
DATE : 08/01/2010 REV: 0 PAGE 1 OF 1
HYDRAULIC DISCONNECT-2.125" OD
ASSY. PART No: 278-21220-00
ITEM NO. QTY. PART NO. REV DESCRIPTION
1 1 278-21220-01 0 TOP SUB (1.5" AMMT )
2 1 49126 0 O-RING
3 1 278-21220-02 0 BODY
4 1 140-063-00 0 5/8" BALL
5 1 50209 0 O-RING
6 1 278-175-03 0 PISTON
7 1 50121 0 O-RING
8 2 50114 0 O-RING
9 4 142-256-01 0 SHEAR SCREW
10 1 278-21220-04 0 BOTTOM SUB (1.5" AMMT )
PARVEEN H YDRAU LIC DISCONN ECT
TECHNICAL MANUAL
PARVEEN H YDRAU LIC DISCONN ECT
TECHNICAL MANUAL
PARVEEN
HYDRAULIC DISCONNECT
TECHNICAL MANUAL
4.0 DISASSEMBLY PROCEDURES
PRE-DISASSEMBLY
PRIOR TO DISASSEMBLY VERIFY THE APPROPRIATE ASSEMBLY DRAWING IS
USED TO AID IN THE IDENTIFICATION OF COMPONENTS IN THE ASSEMBLY
(REFER TO BILL OF MATERIAL).RECORD THE ASSEMBLY MODEL NUMBER AND
SERIAL NUMBERS OF THE HYDRAULIC DISCONNECT.
DISASSEMBLY
1. CLAMP DOWN ON THE BODY (3) TO PREPARE FOR REMOVAL OF
BOTTOM SUB (10) FROM THE BODY (3).
2. REMOVE THE SHEAR SCREW (9) FROM THE BODY (3).
3. REMOVE THE BALL (4).
4. USING A TEFLON ROD PUSH THE PISTON (6) FROM THE BOTTOM
ALLOWING IT TO BE REMOVED.
5. REMOVE THE ORING (5) & (8) FROM THE PISTON (6).
6. PULL THE TOP SUB (1) OUT OF THE BODY (3).
7. REMOVE THE ORING (7) FROM THE TOP SUB (1).
8. REMOVE THE ORING (2) FROM THE BODY (3)
PARVEEN
HYDRAULIC DISCONNECT
TECHNICAL MANUAL
5.0 ASSEMBLY PROCEDURES
PRE-ASSEMBLY PREPARATION CHECK LIST
1. ASSEMBLY AREA SHOULD BE CLEAN.
2. COLLECT THE PROPER TOOLING AND THE TEST FIXTURES.
3. VERIFY THAT THE MOST CURRENT ASSEMBLY PRINT IS USED.
4. ENSURE COMPLETE TRACE-ABILITY EXISTS FOR ALL COMPONENTS
5. CLEAN ALL COMPONENTS WITH A SOLVENT AND BLOW THEM DRY
PRIOR TO ASSEMBLY
6. PRE-INSPECT ALL CRITICAL DIMENSIONS, VERIFY THAT ALL PARTS ARE
IN GOOD CONDITION, BY VISUAL INSPECTION IN GOOD LIGHT AND WITH
MAGNIFICTION WHERE REQUIRED.
7. CHECK THAT ALL NON-METAL PARTS ARE DIMENSIONALLY CORRECT
AND ARE WITHIN USABLE SHELF LIFE LIMITS.
8. ENSURE THAT ALL THREADS AND EDGES ARE CLEAN AND FREE OF
BURRS, SURFACE DEFECTS AND MARKS.INSPECT COATINGS FOR
CONTINUITY.INSPECT FOR PHYSICAL DAMAGE OR CORROSION.
DO NOT USE WORN, PITTED OR DAMAGED PARTS.
ASSEMBLY
1. PLACE THE BODY (3) IN A SOFT JAWED VICE.
2. INSTALL THE ORING (2) IN BODY (3).
3. ASSEMBLE THE TOP SUB (1) WITH THE BODY (3).
4. INSTALL THE ORING (5) & (8) IN PISTON (6).
5. INSERT THE PISTON (6) INTO THE BORE OF THE TOP SUB (1) AND
POSITION SUCH THAT THE GROOVE OF THE PISTON (6) ALIGNS WITH
THE TAPPED HOLES OF THE BODY (3).
6. INSTALL THE SHEAR SCREW (9) IN THE BODY (3) TO HOLD THE PISTON
(6) IN POSITION.
7. ASSEMBLE THE BOTTOM SUB (10) WITH THE BODY (3).
