UM2048

User manual
DSI to HDMI adapter board for STM32 Development Tools

Introduction
The DSI to HDMI adapter board (order code B-LCDAD-HDMI1) provides DSI input port and
HDMI output port. It can be used on STM32 evaluation boards or discovery boards, to
demonstrate video solutions based on STM32 MCUs.
Thanks to the bridge chip ADV7533, the DSI to HDMI adapter board can support
2-, 3- or 4-lanes DSI video input data, S/PDIF, 2-channels I2S audio input data and HDMI
v1.3 output port.
The B-LCDAD-HDMI1 adapter board has the following features:
• Up to four lanes of MIPI/DSI data, each running up to 800 Mbps (video mode only: Non-
Burst mode with synchronization pulse)
• 2-channels I2S transmit stereo up to 192 kHz sampling rate
• S/PDIF carries stereo LPCM audio or compressed audio
• HDMI output connector:
– Support of video resolutions with pixel clocks up to 80 MHz
– Support of CEC signals, 5 V-tolerant I2C and HPD I/Os
– Common-mode filters with ESD protection

Figure 1. DSI to HDMI adapter board

Back side

Front side

Pictures not contractual

June 2016 DocID029197 Rev 1 1/12

www.st.com 1
Contents UM2048

Contents

1 Hardware Layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Video and audio input connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Video input (MIPI DSI) signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Audio input (S/PDIF & I2S) signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Control signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 HDMI output connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 CEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2/12 DocID029197 Rev 1

UM2048 List of tables

List of tables

Table 1. Video and audio input connector CN1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 2. HDMI output connector CN2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 3. CEC source connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 4. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DocID029197 Rev 1 3/12

3
List of figures UM2048

List of figures

Figure 1. DSI to HDMI adapter board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Figure 2. Hardware Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 3. DSI to HDMI adapter board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 4. Board schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4/12 DocID029197 Rev 1

UM2048 Hardware Layout and configuration

1 Hardware Layout and configuration

DSI to HDMI adapter board is designed around the ADV7533. Figure 2 illustrates the
connections on DSI to HDMI adapter board and Figure 3 will help to locate these features
on the actual evaluation board.

Figure 2. Hardware Block Diagram

'6,WR+'0,DGDSWHUERDUG
0RWKHUERDUGFRQQHFWRU

'
'6,9LGHRVLJQDOV

+'0,FRQQHFWRU
0RWKHUERDUG '6,WR+'0,
0LFURFRQWUROOHU $XGLRVLJQDOV +'0,VLJQDOV +'0
EULGJHFKLS ,&DE
OH

&RQWUROVLJQDOV

06Y9

Figure 3. DSI to HDMI adapter board layout

DocID029197 Rev 1 5/12

11
Video and audio input connector UM2048

2 Video and audio input connector

A male high speed connector CN1 on bottom side is used to implement DSI to HDMI
adapter board on mother board. The 4-lane DSI video signals, audio (I2S or S/PDIF)
signals, CEC signals and control signals (I2C bus, reset and interrupt signals) are on this
connector.
Table 1 shows the pinout of CN1.

Table 1. Video and audio input connector CN1

Pin number Description Interface Pin number Description Interface

1 GND - 2 - -
3 DSI_CK_P DSI 4 INT Interrupt output
5 DSI_CK_N DSI 6 GND -
7 GND - 8 DSI_D2_P DSI
9 DSI_D0_P DSI 10 DSI_D2_N DSI
11 DSI_D0_N DSI 12 GND -
13 GND - 14 DSI_D3_P DSI
15 DSI_D1_P DSI 16 DSI_D3_N DSI
17 DSI_D1_N DSI 18 - -
19 GND - 20 - -
21 +5 V - 22 - -
23 +5 V - 24 - -
25 - - 26 - -
27 - - 28 - -
29 - - 30 - -
31 - - 32 - -
33 - - 34 - -
35 SCLK/MCLK Audio 36 3.3 V
37 LRCLK Audio 38 - -
39 I2S/SPDIF Audio 40 I2C_SDA I2C
41 - - 42 - -
43 - - 44 I2C_SCL I2C
45 CEC_CLK CEC 46 - -
47 CEC CEC 48 - -
49 - - 50 - -
51 - - 52 - -
53 - - 54 - -
55 - - 56 - -
57 RESET Reset input 58 - -
59 - - 60 1.8V -

6/12 DocID029197 Rev 1

UM2048 Video and audio input connector

2.1 Video input (MIPI DSI) signals

4-lane MIPI DSI signals are connected on DSI to HDMI adapter board as video input
interface. This board supports 2-, 3- or 4-lane DSI video input data and each running up to
800 Mbps.
DSI interface is compatible with DPHY V.0.90 and DSI V.1.02 and Supports inputs of 16-bit
RGB 4:4:4, 24-bit RGB 4:4:4 and 30-bit RGB 4:4:4.

2.2 Audio input (S/PDIF & I2S) signals

S/PDIF or I2S audio input interface is implemented on CN1. DSI to HDMI adapter board
supports standard S/PDIF for stereo LPCM or compressed audio up to 192 kHz, or 2-
channel uncompressed LPCM I2S audio up to 192 kHz.

2.3 Control signals

I2C bus on CN1 serves as the serial port data I/O slave for register access. The default
address is 0x7A.
Reset signal from mother board is connected to Power Down (PD) pin on ADV7533. It is
internal pulled up by ADV7533.
Interrupt output signal is for mother board and it is pull up on DSI to HDMI adapter board.

DocID029197 Rev 1 7/12

11
HDMI output connector UM2048

3 HDMI output connector

A standard HDMI output connector CN2 is implemented on DSI to HDMI adapter board. The
output supports all video and graphics resolutions from 480i to 1080p at 30 Hz. Thanks to
common-mode filter with ESD protection parts, HDMI output connector is complies with IEC
61000-4-2 level 4 standard.
On CN2, I2C master for EDID reading and HDCP operations reports HDMI events through
interrupts and registers. Hot Plug Detect Signal (HPD) Indicates to the interface whether the
receiver is connected.
Table 2 shows the pinout of CN2.

Table 2. HDMI output connector CN2

Pin number Description Pin number Description

1 TMDS D2+ 11 GND

2 GND 12 TMDS Clock-
3 TMDS D2- 13 CEC
4 TMDS D1+ 14 NC
5 GND 15 DDC_I2C_SCL
6 TMDS D1- 16 DDC_I2C_SDA
7 TMDS D0+ 17 GND
HDMI_5V_Source from
8 GND 18
power switch U5
9 TMDS D0- 19 HPD
10 TMDS Clock+ - -

8/12 DocID029197 Rev 1

UM2048 CEC

4 CEC

There are two sources of CEC signal on HDMI output connector on DSI to HDMI adapter
board. One source (Default setting) is from ADV7533 and its clock is from X1 on the board.
The other source is from CN1 and mother board. Some PCB reworks should be done when
using the second source shown in Table 3.

Table 3. CEC source connection

CEC source Mount Remove

ADV7533 (Default) SB10 SB5

CN1 (Mother board) SB5 SB10

DocID029197 Rev 1 9/12

11
 5 Schematic
10/12

Schematic
Figure 4. Board schematic
+1V8_CON V1P2 +3V3 +1V8
SB2 Open
+1V8

L1

L2

L3

L4

L5

L6
U1 SB1
+3V3 LD1117S18TR Closed
3 2 SB3 Closed
Vin Vout V1P2
4
Tab

10uH

10uH

10uH

10uH

10uH

10uH
R10
C1 C2
10uF 10uF

1
120[N/A] C3 C4 C5 C6 C7 C8

10uF 10uF 10uF 10uF 10uF 10uF

C9 100nF C10 100nF C11 100nF C12 100nF C13 100nF
C14 100nF
C15 100nF C16 100nF

Source
+3V3 C17 100nF
U2
CN1 ADV7533BCBZ-RL
R1

D4

G7

G1
B1

B4

C6
Differential pairs 100ohm I2C address:0x7A

E3

E4
E2
2K 2 1 Differential pairs 100ohm U3

21
20
2 1
INT 4 3 HSSI_CLK_P ECMF04-4HSWM10
4 3

V1P2
V1P2

V3P3

AVDD

A2VDD

PVDD

DVDD
DVDD
DVDD
6 5 HSSI_CLK_N G5 A1 TMDS_Data2+ 6 5 1 CN2
6 5 DRx2+ Tx2+ D2- D2-
HSSI_D2_P 8 7 F5 A2 TMDS_Data2- 7 4 2
8 7 DRx2- Tx2- D2+ D2+
HSSI_D2_N 10 9 HSSI_D0_P 8 3 3
10 9 GND GND
12 11 HSSI_D0_N G6 A3 TMDS_Data1+ 9 2 4
12 11 DRx3+ Tx1+ D1- D1-
HSSI_D3_P 14 13 F6 A4 TMDS_Data1- 10 1 5
14 13 DRx3- Tx1- D1+ D1+
DocID029197 Rev 1

HSSI_D3_N 16 15 HSSI_D1_P 6
16 15
18 17 HSSI_D1_N G2 A5 U4 7
18 17 DRxC+ Tx0+
Differential pairs 100ohm 20 19 F2 A6 TMDS_Data0+ 6 5 8
20 19 DRxC- Tx0- D2- D2-
22 21 TMDS_Data0- 7 4 9
22 21 +5V D2+ D2+
24 23 G3 A7 8 3 10
+3V3 24 23 C18 DRx0+ TxC+ GND GND
26 25 F3 B7 TMDS_Clock+ 9 2 11
C19 26 25 100nF DRx0- TxC- D1- D1-
28 27 TMDS_Clock- 10 1 12
100nF 28 27 D1+ D1+
30 29 G4 B2 13
30 29 DRx1+ GND
32 31 F4 B3 CEC ECMF04-4HSWM10 14

HD119F-3A09200
32 31 DRx1- GND
34 33 B5 DDC_SCL 15
34 33 GND
36 35 SCLK C2 B6 DDC_SDA 16
36 35 SCLK/MCLK GND
38 37 LRCLK D3 C7 17
38 37 LRCLK GND
I2C_SDA 40 39 I2S C1 E1 18
40 39 I2S/SPDIF GND
42 41

DDC_SDA
E7 HPD 19

DDC_SCL

CEC_CLK
42 41 GND
I2C_SCL 44 43 C5 F1
44 43 R_EXT GND
46 45 CEC_CLK SB4 Open F7 +5V

SDA

HPD

CEC
SCL
46 45 GND

22
INT
48 47 CEC_IO SB5 Open R12 R13 R2

PD
48 47 10K 10K 1K[1%]
50 49 SB6
50 49 R3 R4
52 51 Closed
52 51 SB7

C3

E6
E5

D5

C4

D2
D1

D7
D6
54 53 2K[N/A] 2K[N/A] U5
54 53
56 55 Open 3 2
56 55 FAULT GND
+1V8_CON 58 57 RST SB8 Closed 1 5

INT
58 57 HDMI_5V_Source OUT IN +5V
60 59 4
60 59 EN
R5
C21 C20
61 2K[N/A] +3V3 STMPS2141STR@54
100nF 61 R6 C22 4.7uF
62
62 SB9 10K 100nF
63
63 R7
64 +1V8 Open
64 D1 27K
QTH-030-02-F-D-A U6
Connector for motherboard SB11 A3 A1
R8 R9 SCL 5V +5V
Closed SB10 BAR18 B3 C1
[N/A] [N/A] SDA RPU C23 C24
Closed
A2 B2 100nF 100nF
CEC GND
C3 C2
HPD GND
X1 HDMI05-CL01F3
3 4 SB12 Closed
OUT VDD +1V8
SB13 Open
+3V3
2 1 R11 10K Note: Text in italic placed on a wire doesn¡¯t correspond to net name. It just helps to
GND EN
identify rapidly MCU IO related to this wire.
H1 NZ2520SB-12.000000M-NSA3412D C25 Title: DSI to HDMI adapter
100nF
Project: HDMI daugher board
Size: A4 Reference: MB1232 Revision: A.1
Date: 5/20/2016 Sheet: 1 of 1

UM2048
UM2048 Revision history

6 Revision history

Table 4. Document revision history

Date Revision Changes

09-Jun-2016 1 Initial release.

DocID029197 Rev 1 11/12

11
 UM2048

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2016 STMicroelectronics – All rights reserved

12/12 DocID029197 Rev 1