PIPELINE CORRIDOR FROM

FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 1 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

Ball Valve (3/4"~14")Data Sheets

EBS1-FPFA00-SAPI-DSVL-1022-D00

Date Sign

Code I Information only Submission - Accepted

Rejected – Major Comments – Data Provider to revise and re-submit. Work should NOT proceed
Code R
in the affected areas until comments are resolved.

Code C Comments Returned – Data provider to revise and re-submit for the further review.

Code A Accepted – Approved – No further submission required

Review Code and Status

D00 2019-05-31 IFC He Hui Xin Meng Xu Yandi Jiang Zhiyang

Prepared Revised Checked

Rev Data Reason for Issue Approved by
by by By
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 2 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

Revision
Rev Date Issued Update/ Amendment Details
Description
D00 IFC 2019-05-31 Issued for Comments
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 3 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

INDEX
DESCRIPTION PAGE NUMBER

BALL VALVE API 608 CLASS 300 5

BALL VALVE API 6D CLASS 300 7
BALL VALVE API 608 CLASS 150 11
BALL VALVE API 6D CLASS 150 13
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 4 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

HOLDS
HOLD No. Section Description

1 No hold
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 5 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB52BRS VALVE TYPE: FLOATING BALL (FB), SOFT SEAT- SOUR PIPE CLASS : CN22
RATING: ASME B16.5 CL300 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN20 THRU DN40
GENERAL REQUIREMNETS & DETAILS (NOTE1) Rev. MATERIAL (NOTES 2 & 3) Rev.
DESIGN CONDITIONS MATERIAL ASME B16.34 /ASME B31.3
DESIGN PRESSURE Min.Fv Max.40 barg SERVICE/CORROSION SOUR SERVICE NACE
DESIGN TEMPERATURE ℃ Min.-15℃ Max.85℃ NON METALLIC MATERIAL SUITABLE FOR DESIGN CONDITIONS
SERVICE MEDIUMS CRUDE OIL ,GAS AND WATER
APPROVALS/CERTIFICATIONS (MANUFACTURE)
CE APPROVAL
ISO9001 APPROVAL
API API 607 CERTIFIED OR API 6FA CERTIFIED

CORROSION ALLOWANCE 3 mm MATERIALS - WETTED COMPONENTS (NOTE 2)

TEST CRITERIA BODY/BONNET ASTM A105N
SHELL PRESSURE AS PER API 598 MATCH FLANGES (IF REQUIRED) ASTM A105N
BACK SEAT PRESSURE N/A OBTURATOR (BALL) ASTM A182 F316L
HYDROSTATIC SEAT TEST ACCEPTANCE AS PER API 598 OBTURATOR RETAINER VTA*
LOW PRESSURE CLOSURE AS PER API 598 STEM (NOTE 11) ASTM A276 T316 /VTA*
HIGH PRESSURE CLOSURE AS PER API 598 STEM/TRUNN THRUST WASH VTA*
FUGITIVE EMISSIONS BS EN ISO 15848-2 Class B STEM/TRUNN BUSH/BEARING VTA*
DESIGN CRETERIA (NOTES 2 & 7) STEM GLAND SEAL/PACKING LIP SEAL/GRAPHITE /VTA*(NOTE 8 )
VALVE TYPE & STYLE FLOATING BALL BUSHING VTA*
FLOW DIRECTION BI-DIRECTIONAL
VALVE DESIGN API 608 SEAT RPTFE /VTA*(NOTE 13)
BODY TYPE ONE PIECE LIP SEAL RPTFE + INCONEL X750*(NOTE 13)
BODY PATTERN LONG PATTERN O RINGS FFKM / VTA *(NOTE 13)
BORE (NOTE 5) FULL BORE GASKETS SW 316L / GRAPHITE FILLER
CRYOGENIC BONNET N/A SPRINGS (IF REQUIRED) INCONEL X750
OBTURATOR TYPE CONCENTRIC BALL STUD BOLTS & NUT ASTM A193 B7M/A194 2HM
OBTURATOR DESIGN SOLID BALL ONE PIECE (NOTE 6) DRAIN VALVES SEAT N/A
STEM DESIGN ASME B16.34 & API 608 DRAIN VALVES BODY N/A
ENERGIZED LIP SEAL + SINGLE WIPER +
STEM/BODY SEAL (NOTE8) FIRESEAL
DRAIN PLUGS ASTM A105N
METAL SEAT RING WITH SOFT SEAT AS PER
SEAT DESIGN API 608
SEAT RING/BODY SEAL LIP SEAL *
BODY/ INSERT SEAL SPIRAL WOUND GASKET*
STANDARDS & SPECIFICATIONS
CODE ASME B16.34 & API 608
DESIGN & TESTING ASME B16.34 & API 608 (NOTE 2)
END TO END DIMENSIONS API 608 MATERIALS - NON WETTED COMPONENTS (NOTE 2)
BODY/BONNET TAPPING VTA * MANUAL OPERATOR WRENCH ASTME A216 WCB
FUGITIVE EMISSIONS BS EN ISO 15848-2 GEAR OPERATOR N/A
OPERATOR YOKE VTA * GLAND FLANGE ASTM A105N
MATERIAL CERTIFICATION PRESSURE PARTS - BS EN 10204 - 3.1 GLAND FOLLOWER SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
TRIM - BS EN 10204 - 3.1 SHAFT/SPINDLE/KEYS SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
SAFETY LIFTING ATTACHMENTS * (NOTE9)
FLUID THERMAL EXPANSION ASME B16.34, NO DRILLING OF OBTURATOR ANTI-STATIC DEVICE VTA*
STEM RETENTION ASME B16.34 & API 608 STEM NUT ASTM A182 F6a*
ANTI STATIC API 608 MISC COMPONENTS SUITABLE FOR DESIGN TEMPS. *
FIRE SAFE API 607 CERTIFIED
OR API 6FA CERTIFIED
GENERAL:
PROJECT SPECIFICATION 1、THE DATASHEET SHALL BE COMPLETED AND ALL BLANKS WITH * SHALL
EBS1-FPFA00-SAPI-SPMT-1001 PIPNG AND VALVE MATERIAL BE ADVISED AND FILLED BY MANUFACTURER.
SPECIFICATION
2、WETTED PART SHALL BE SUITABLE FOR SOUR SERVICE TO NACE
MR0175/ISO 15156.
EBS1-FSFA11-SAPI-SPMT-1002 BALL VALVE (3/4"~ 14" ) SPECIFICATION
3、ALL GENERAL AND NOTES SHALL BE COMPLIED.
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 6 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB52BRS VALVE TYPE: FLOATING BALL (FB), SOFT SEAT- SOUR PIPE CLASS : CN22
RATING: ASME B16.5 CL300 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN20 THRU DN40
NOTES:
1、ANY DEVIATION FROM THE DATA SHEET AND REFERENCE SPECIFICATIONS SHALL BE STATED AND APPROVED.
2、ALL MATERIALS (METALLIC & NON METALLIC) SHALL BE SUITABLE FOR THE FULL PRESSURE RATING OVER THE DESIGN TEMPERATURE RANGE.
3、ASBESTOS IS NOT ACCEPTABLE FOR ANY VALVE PARTS.
4、VALVE SHALL BE MARKED IN ACCODANCE WITH MSS-SP-25.
5、FULL BORE BALL VALVES SHALL BE SUPPLIED ACCORDING TO API 608 REQUIREMENTS.
6、BALL VALVES SHALL NOT BE SUPPLIED WITH BALL AND STEM AS ONE PIECE.
7、VALVES SHALL BE SUPPLIED WITH A DEVICE TO ENABLE THE VALVE TO BE LOCKED IN THE OPEN/CLOSED POSITION.
8、ALL GRAPHITE SEALS TO BE SUPPLIED WITH CORROSION INHIBITOR.

9、VALVES IN EXCESS OF 50KG TO INCLUDE FOR BALANCED LIFTING LUGS (FLANGES AND/OR TOP COVERS SHALL NOT BE USED) AND VALVES IN EXCESS
OF 100KG TO BE SUPPLIED WITH SUPPORT LEGS.

10、THE STEM MATERIAL SHALL BE SUFFICIENT INTENSITY TO MEET REQUIREMENTS OF VALVE TORQUE.
11、MANUFACTURE SHALL CHARGE OF ALL RESPONSIBILITY FOR MATAERIALS THAT PROPOSED BY MANUFACTURE.
12、MANUFACTURE SHALL CONSIDE OVER MATERIALS' GALVANIC CORROSION FOR ALL COMPONENTS.
13、THE SOFT MATERIAL FOR LIP SEAL, SEAT AND O RING SHALL BE USED UP TO 100℃.
14、VALVES DESIGN SHALL ALLOW FOR INSULATION BOXES.
15、PURCHASED QUANTITIES AND SIZE IN ACCORDANCE WITH MTO .
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 7 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB92BRS VALVE TYPE: BALL (RB), SOFT SEAT - SOUR PIPE CLASS : CN22
RATING: ASME B16.5 CL300 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN150 THRU DN350
GENERAL REQUIREMNETS & DETAILS (NOTE1) Rev. MATERIAL (NOTES 2 & 3) Rev.
DESIGN CONDITIONS MATERIAL ASME B16.34 /ASME B31.3
DESIGN PRESSURE Min.Fv Max.40 barg SERVICE/CORROSION SOUR SERVICE NACE
DESIGN TEMPERATURE ℃ Min.-15℃ Max.85℃ NON METALLIC MATERIAL SUITABLE FOR DESIGN CONDITIONS
SERVICE MEDIUMS CRUDE OIL ,GAS AND WATER
APPROVALS/CERTIFICATIONS (MANUFACTURE)
CE APPROVAL
ISO9001 APPROVAL
API API 6D
API 607 CERTIFIED OR API 6FA CERTIFIED
CORROSION ALLOWANCE 3 mm MATERIALS - WETTED COMPONENTS (NOTE 2 & 11)
TEST CRITERIA BODY/BODY COVER ASTM A105N
SHELL PRESSURE API 6D MATCH FLANGES (IF REQUIRED) ASTM A105N
BACK SEAT PRESSURE N/A OBTURATOR (BALL) ASTM A182 F316L
HYDROSTATIC SEAT TEST ACCEPTANCE AS PER ISO 5208 RATE A OBTURATOR RETAINER ASTM A182 F316L
LOW PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM ASTM A276 T316
HIGH PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM/TRUNN THRUST WASH ASTM A182 F316L
FUGITIVE EMISSIONS BS EN ISO 15848-2 Class B STEM/TRUNN BUSH/BEARING ASTM A182 F316L
DESIGN CRETERIA (NOTES 2) STEM GLAND SEAL/PACKING LIP SEAL & GRAPHITE (NOTE 8 )
VALVE TYPE & STYLE DIB-2 TRUNNION MOUNTED BUSHING ASTM A182 F316L WITH PTFE
FLOW DIRECTION UNI-DIRECTIONAL SEAT RING ASTM A182 F316L
VALVE DESIGN API 6D SEAT INSERT FFKM (NOTE 13)
BODY TYPE THREE PIECES LIP SEAL RPTFE + INCONEL X750 (NOTE 13)
BODY PATTERN LONG PATTERN O RINGS FFKM (NOTE 13)
BORE (NOTE 5) REDUCED BORE GASKETS SW 316L / GRAPHITE FILLER
CRYOGENIC BONNET N/A SPRINGS INCONEL X750
OBTURATOR TYPE CONCENTRIC BALL STUD BOLTS & NUT ASTM A193 B7M/A194 2HM
OBTURATOR DESIGN SOLID BALL ONE PIECE DRAIN VALVES SEAT ASTM A182 F316L WITH SOFT SEAL
STEM DESIGN ASME B16.34 & API 6D DRAIN VALVES BODY ASTM A105N (NOTE 16)
ENERGIZED LIP SEAL + SINGLE WIPER +
STEM/BODY SEAL FIRESEAL
DRAIN PLUGS ASTM A105N (NOTE 16)
METAL SEAT RING WITH SOFT SEAT AS PER
SEAT DESIGN API 6D
SEAT RING/BODY SEAL LIP SEAL
BODY/COVER SEAL SPIRAL WOUND GASKET
STANDARDS & SPECIFICATIONS
CODE ASME B16.34 & API 6D
DESIGN & TESTING ASME B16.34 & API 6D
END TO END DIMENSIONS API 6D MATERIALS - NON WETTED COMPONENTS (NOTE 2)
BODY/BONNET TAPPING N/A MANUAL OPERATOR HAND WHEEL ASTM A216 WCB
FUGITIVE EMISSIONS BS EN ISO 15848-2 GEAR OPERATOR VTA*
OPERATOR YOKE ISO 5211 GLAND FLANGE ASTM A105N
MATERIAL CERTIFICATION PRESSURE PARTS - BS EN 10204 - 3.2 GLAND FOLLOWER SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
TRIM - BS EN 10204 - 3.1 SHAFT/SPINDLE/KEYS ATSM A276 T410 (H) (NOTE 1)
SAFETY LIFTING ATTACHMENTS ASTM A105N (NOTE9)
FLUID THERMAL EXPANSION ASME B16.34, NO DRILLING OF OBTURATOR ANTI-STATIC DEVICE ASTM A182 F316L
STEM RETENTION ASME B16.34 & API 6D STEM NUT ASTM A182 F6a*
ANTI STATIC API 6D MISC COMPONENTS SUITABLE FOR DESIGN TEMPS. *
FIRE SAFE API 607 CERTIFIED
OR API 6FA CERTIFIED
GENERAL:
PROJECT SPECIFICATION 1、THE DATASHEET SHALL BE COMPLETED AND ALL BLANKS WITH * SHALL
EBS1-FPFA00-SAPI-SPMT-1001 PIPNG AND VALVE MATERIAL BE ADVISED AND FILLED BY MANUFACTURER.
SPECIFICATION
2、WETTED PART SHALL BE SUITABLE FOR SOUR SERVICE TO NACE
MR0175/ISO 15156.
EBS1-FSFA11-SAPI-SPMT-1002 BALL VALVE (3/4"~ 14" ) SPECIFICATION
3、ALL GENERAL AND NOTES SHALL BE COMPLIED.
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 8 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB92BRS VALVE TYPE: BALL (RB), SOFT SEAT - SOUR PIPE CLASS : CN22
RATING: ASME B16.5 CL300 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN150 THRU DN350
NOTES:
1、ANY DEVIATION FROM THE DATA SHEET AND REFERENCE SPECIFICATIONS SHALL BE STATED AND APPROVED.
2、ALL MATERIALS (METALLIC & NON METALLIC) SHALL BE SUITABLE FOR THE FULL PRESSURE RATING OVER THE DESIGN TEMPERATURE RANGE.
3、ASBESTOS IS NOT ACCEPTABLE FOR ANY VALVE PARTS.
4、VALVE SHALL BE MARKED IN ACCODANCE WITH MSS-SP-25.
5、REDUCED BORE BALL VALVES SHALL BE SUPPLIED WITH ONE SIZE REDUCTION (IE DN100 X DN80) IF REQUIRED.
6、BALL VALVES SHALL NOT BE SUPPLIED WITH BALL AND STEM AS ONE PIECE.
7、VALVES SHALL BE SUPPLIED WITH A DEVICE TO ENABLE THE VALVE TO BE LOCKED IN THE OPEN/CLOSED POSITION.
8、ALL GRAPHITE SEALS TO BE SUPPLIED WITH CORROSION INHIBITOR.

9、VALVES IN EXCESS OF 50KG TO INCLUDE FOR BALANCED LIFTING LUGS (FLANGES AND/OR TOP COVERS SHALL NOT BE USED) AND VALVES IN EXCESS
OF 100KG TO BE SUPPLIED WITH SUPPORT LEGS.

10、THE STEM MATERIAL SHALL BE SUFFICIENT INTENSITY TO MEET REQUIREMENTS OF VALVE TORQUE.
11、MANUFACTURE SHALL CHARGE OF ALL RESPONSIBILITY FOR MATAERIALS THAT PROPOSED BY MANUFACTURE.
12、MANUFACTURE SHALL CONSIDE OVER MATERIALS' GALVANIC CORROSION BETWEEN TRUNNION AND BUSHING.
13、THE SOFT MATERIAL FOR LIP SEAL, SEAT INSERT AND O RING SHALL BE USED UP TO 100℃.
14、VALVES DESIGN SHALL ALLOW FOR INSULATION BOXES.
15、PURCHASED QUANTITIES AND SIZE IN ACCORDANCE WITH MTO .

16、FOR BALL VALVES WITH DIMENSION ARE GREATER THAN DN80 (INCLUDE DN80) SHALL BE FITTED WITH DRAIN VALVE.

17、THE VALVE BODY SHALL BE FURNISHED WITH A ARROW TO INDICATE THE DIRECTIONA OF FLOW THROUG THE VALVE.
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 9 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RBH2BRS VALVE TYPE: BALL (FB), SOFT SEAT - SOUR PIPE CLASS : CN22
RATING: ASME B16.5 CL300 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN50 THRU DN350
GENERAL REQUIREMNETS & DETAILS (NOTE1) Rev. MATERIAL (NOTES 2 & 3) Rev.
DESIGN CONDITIONS MATERIAL ASME B16.34 /ASME B31.3
DESIGN PRESSURE Min.Fv Max.40 barg SERVICE/CORROSION SOUR SERVICE NACE
DESIGN TEMPERATURE ℃ Min.-15℃ Max.85℃ NON METALLIC MATERIAL SUITABLE FOR DESIGN CONDITIONS
SERVICE MEDIUMS CRUDE OIL ,GAS AND WATER
APPROVALS/CERTIFICATIONS (MANUFACTURE)
CE APPROVAL
ISO9001 APPROVAL
API API 6D
API 607 CERTIFIED OR API 6FA CERTIFIED
CORROSION ALLOWANCE 3 mm MATERIALS - WETTED COMPONENTS (NOTE 2 & 11)
TEST CRITERIA BODY/BODY COVER ASTM A105N
SHELL PRESSURE API 6D MATCH FLANGES (IF REQUIRED) ASTM A105N
BACK SEAT PRESSURE N/A OBTURATOR (BALL) ASTM A182 F316L
HYDROSTATIC SEAT TEST ACCEPTANCE AS PER ISO 5208 RATE A OBTURATOR RETAINER ASTM A182 F316L
LOW PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM ASTM A276 T316
HIGH PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM/TRUNN THRUST WASH ASTM A182 F316L
FUGITIVE EMISSIONS BS EN ISO 15848-2 Class B STEM/TRUNN BUSH/BEARING ASTM A182 F316L
DESIGN CRETERIA (NOTES 2) STEM GLAND SEAL/PACKING LIP SEAL & GRAPHITE (NOTE 8 )
VALVE TYPE & STYLE DIB-2 TRUNNION MOUNTED BUSHING ASTM A182 F316L WITH PTFE
FLOW DIRECTION UNI-DIRECTIONAL SEAT RING ASTM A182 F316L
VALVE DESIGN API 6D SEAT INSERT FFKM (NOTE 13)
BODY TYPE THREE PIECES LIP SEAL RPTFE +INCONEL X750 (NOTE 13)
BODY PATTERN LONG PATTERN O RINGS FFKM (NOTE 13)
BORE (NOTE 5) FULL BORE GASKETS SW 316L / GRAPHITE FILLER
CRYOGENIC BONNET N/A SPRINGS INCONEL X750
OBTURATOR TYPE CONCENTRIC BALL STUD BOLTS & NUT ASTM A193 B7M/A194 2HM
OBTURATOR DESIGN SOLID BALL ONE PIECE DRAIN VALVES SEAT ASTM A182 F316L WITH SOFT SEAL
STEM DESIGN ASME B16.34 & API 6D DRAIN VALVES BODY ASTM A105N (NOTE 16)
ENERGIZED LIP SEAL + SINGLE WIPER +
STEM/BODY SEAL FIRESEAL
DRAIN PLUGS ASTM A105N (NOTE 16)
METAL SEAT RING WITH SOFT SEAT AS PER
SEAT DESIGN API 6D
SEAT RING/BODY SEAL LIP SEAL
BODY/COVER SEAL SPIRAL WOUND GASKET
STANDARDS & SPECIFICATIONS
CODE ASME B16.34 & API 6D
DESIGN & TESTING ASME B16.34 & API 6D
END TO END DIMENSIONS API 6D MATERIALS - NON WETTED COMPONENTS (NOTE 2)
BODY/BONNET TAPPING N/A MANUAL OPERATOR HAND WHEEL ASTM A216 WCB
FUGITIVE EMISSIONS BS EN ISO 15848-2 GEAR OPERATOR VTA*
OPERATOR YOKE ISO 5211 GLAND FLANGE ASTM A105N
MATERIAL CERTIFICATION PRESSURE PARTS - BS EN 10204 - 3.2 GLAND FOLLOWER SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
TRIM - BS EN 10204 - 3.1 SHAFT/SPINDLE/KEYS ATSM A276 T410 (H) (NOTE 1)
SAFETY LIFTING ATTACHMENTS ASTM A105N (NOTE9)
FLUID THERMAL EXPANSION ASME B16.34, NO DRILLING OF OBTURATOR ANTI-STATIC DEVICE ASTM A182 F316L
STEM RETENTION ASME B16.34 & API 6D STEM NUT ASTM A182 F6a*
ANTI STATIC API 6D MISC COMPONENTS SUITABLE FOR DESIGN TEMPS. *
FIRE SAFE API 607 CERTIFIED
OR API 6FA CERTIFIED
GENERAL:
PROJECT SPECIFICATION 1、THE DATASHEET SHALL BE COMPLETED AND ALL BLANKS WITH * SHALL
EBS1-FPFA00-SAPI-SPMT-1001 PIPNG AND VALVE MATERIAL BE ADVISED AND FILLED BY MANUFACTURER.
SPECIFICATION
2、WETTED PART SHALL BE SUITABLE FOR SOUR SERVICE TO NACE
MR0175/ISO 15156.
EBS1-FSFA11-SAPI-SPMT-1002 BALL VALVE (3/4"~ 14" ) SPECIFICATION
3、ALL GENERAL AND NOTES SHALL BE COMPLIED.
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 10 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RBH2BRS VALVE TYPE: BALL (FB), SOFT SEAT - SOUR PIPE CLASS : CN22
RATING: ASME B16.5 CL300 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN50 THRU DN350
NOTES:
1、ANY DEVIATION FROM THE DATA SHEET AND REFERENCE SPECIFICATIONS SHALL BE STATED AND APPROVED.
2、ALL MATERIALS (METALLIC & NON METALLIC) SHALL BE SUITABLE FOR THE FULL PRESSURE RATING OVER THE DESIGN TEMPERATURE RANGE.
3、ASBESTOS IS NOT ACCEPTABLE FOR ANY VALVE PARTS.
4、VALVE SHALL BE MARKED IN ACCODANCE WITH MSS-SP-25.
5、FULL BORE BALL VALVES SHALL BE SUPPLIED ACCORDING TO API 6D REQUIREMENTS..
6、BALL VALVES SHALL NOT BE SUPPLIED WITH BALL AND STEM AS ONE PIECE.
7、VALVES SHALL BE SUPPLIED WITH A DEVICE TO ENABLE THE VALVE TO BE LOCKED IN THE OPEN/CLOSED POSITION.
8、ALL GRAPHITE SEALS TO BE SUPPLIED WITH CORROSION INHIBITOR.

9、VALVES IN EXCESS OF 50KG TO INCLUDE FOR BALANCED LIFTING LUGS (FLANGES AND/OR TOP COVERS SHALL NOT BE USED) AND VALVES IN EXCESS
OF 100KG TO BE SUPPLIED WITH SUPPORT LEGS.

10、THE STEM MATERIAL SHALL BE SUFFICIENT INTENSITY TO MEET REQUIREMENTS OF VALVE TORQUE.
11、MANUFACTURE SHALL CHARGE OF ALL RESPONSIBILITY FOR MATAERIALS THAT PROPOSED BY MANUFACTURE.
12、MANUFACTURE SHALL CONSIDE OVER MATERIALS' GALVANIC CORROSION BETWEEN TRUNNION AND BUSHING.
13、THE SOFT MATERIAL FOR LIP SEAL,SEAT INSERT AND O RING SHALL BE USED UP TO 100℃.
14、VALVES DESIGN SHALL ALLOW FOR INSULATION BOXES.
15、PURCHASED QUANTITIES AND SIZE IN ACCORDANCE WITH MTO .

16、FOR BALL VALVES WITH DIMENSION ARE GREATER THAN DN80 (INCLUDE DN80) SHALL BE FITTED WITH DRAIN VALVE. THE OTHER DIMENSION SHALL
BE FITTED WITH DRAIN PLUG.

17、THE VALVE BODY SHALL BE FURNISHED WITH A ARROW TO INDICATE THE DIRECTIONA OF FLOW THROUG THE VALVE.
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 11 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB52ARN VALVE TYPE: FLOATING BALL (FB), SOFT SEAT- NON SOUR PIPE CLASS : AN21
RATING: ASME B16.5 CL150 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN15 THRU DN40
GENERAL REQUIREMNETS & DETAILS (NOTE1) Rev. MATERIAL (NOTES 2 & 3) Rev.
DESIGN CONDITIONS MATERIAL ASME B16.34 /ASME B31.3
DESIGN PRESSURE Min.Fv Max.40 barg SERVICE/CORROSION NON SOUR SERVICE NACE
DESIGN TEMPERATURE ℃ Min.-15℃ Max.85℃ NON METALLIC MATERIAL SUITABLE FOR DESIGN CONDITIONS
SERVICE MEDIUMS CRUDE OIL
APPROVALS/CERTIFICATIONS (MANUFACTURE)
CE APPROVAL
ISO9001 APPROVAL
API API 607 CERTIFIED OR API 6FA CERTIFIED

CORROSION ALLOWANCE 3 mm MATERIALS - WETTED COMPONENTS (NOTE 2)

TEST CRITERIA BODY/BONNET ASTM A105N
SHELL PRESSURE AS PER API 598 MATCH FLANGES (IF REQUIRED) ASTM A105N
BACK SEAT PRESSURE N/A OBTURATOR (BALL) ASTM A182 F316L
HYDROSTATIC SEAT TEST ACCEPTANCE AS PER API 598 OBTURATOR RETAINER VTA*
LOW PRESSURE CLOSURE AS PER API 598 STEM (NOTE 10) ASTM A182 F6A /VTA*
HIGH PRESSURE CLOSURE AS PER API 598 STEM/TRUNN THRUST WASH VTA*
FUGITIVE EMISSIONS N/A STEM/TRUNN BUSH/BEARING VTA*
DESIGN CRETERIA (NOTES 2 & 7) STEM GLAND SEAL/PACKING LIP SEAL/GRAPHITE /VTA*(NOTE 8 )
VALVE TYPE & STYLE FLOATING BALL BUSHING VTA*
FLOW DIRECTION BI-DIRECTIONAL
VALVE DESIGN API 608 SEAT RPTFE /VTA*(NOTE 13)
BODY TYPE ONE PIECE LIP SEAL RPTFE + INCONEL X750*(NOTE 13)
BODY PATTERN LONG PATTERN O RINGS FKM / VTA *(NOTE 13)
BORE (NOTE 5) FULL BORE GASKETS SW 316L / GRAPHITE FILLER
CRYOGENIC BONNET N/A SPRINGS (IF REQUIRED) INCONEL X750
OBTURATOR TYPE CONCENTRIC BALL STUD BOLTS & NUT ASTM A193 B7M/A194 2HM
OBTURATOR DESIGN SOLID BALL ONE PIECE (NOTE 6) DRAIN VALVES SEAT N/A
STEM DESIGN ASME B16.34 & API 608 DRAIN VALVES BODY N/A
ENERGIZED LIP SEAL + SINGLE WIPER +
STEM/BODY SEAL (NOTE8) FIRESEAL
DRAIN PLUGS ASTM A105N
METAL SEAT RING WITH SOFT SEAT AS PER
SEAT DESIGN API 608
SEAT RING/BODY SEAL LIP SEAL *
BODY/ INSERT SEAL SPIRAL WOUND GASKET*
STANDARDS & SPECIFICATIONS
CODE ASME B16.34 & API 608
DESIGN & TESTING ASME B16.34 & API 608 (NOTE 2)
END TO END DIMENSIONS API 608 MATERIALS - NON WETTED COMPONENTS (NOTE 2)
BODY/BONNET TAPPING VTA * MANUAL OPERATOR WRENCH ASTME A216 WCB
FUGITIVE EMISSIONS N/A GEAR OPERATOR N/A
OPERATOR YOKE VTA * GLAND FLANGE ASTM A105N
MATERIAL CERTIFICATION PRESSURE PARTS - BS EN 10204 - 3.1 GLAND FOLLOWER SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
TRIM - BS EN 10204 - 3.1 SHAFT/SPINDLE/KEYS SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
SAFETY LIFTING ATTACHMENTS * (NOTE9)
FLUID THERMAL EXPANSION ASME B16.34, NO DRILLING OF OBTURATOR ANTI-STATIC DEVICE VTA*
STEM RETENTION ASME B16.34 & API 608 STEM NUT ASTM A182 F6A*
ANTI STATIC API 608 MISC COMPONENTS SUITABLE FOR DESIGN TEMPS. *
FIRE SAFE API 607 CERTIFIED
OR API 6FA CERTIFIED
GENERAL:
PROJECT SPECIFICATION 1、THE DATASHEET SHALL BE COMPLETED AND ALL BLANKS WITH * SHALL
EBS1-AAAA00-MEPI-SPMT-1001 PIPNG AND VALVE MATERIAL BE ADVISED AND FILLED BY MANUFACTURER.
SPECIFICATION
2、ALL GENERAL AND NOTES SHALL BE COMPLIED.
EBS1-AAAA00-SAPI-SPMT-1090 BALL VALVE SPECIFICATION
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 12 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB52ARN VALVE TYPE: FLOATING BALL (FB), SOFT SEAT- NON SOUR PIPE CLASS : AN21
RATING: ASME B16.5 CL150 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN15 THRU DN40
NOTES:
1、ANY DEVIATION FROM THE DATA SHEET AND REFERENCE SPECIFICATIONS SHALL BE STATED AND APPROVED.
2、ALL MATERIALS (METALLIC & NON METALLIC) SHALL BE SUITABLE FOR THE FULL PRESSURE RATING OVER THE DESIGN TEMPERATURE RANGE.
3、ASBESTOS IS NOT ACCEPTABLE FOR ANY VALVE PARTS.
4、VALVE SHALL BE MARKED IN ACCODANCE WITH MSS-SP-25.
5、FULL BORE BALL VALVES SHALL BE SUPPLIED ACCORDING TO API 608 REQUIREMENTS.
6、BALL VALVES SHALL NOT BE SUPPLIED WITH BALL AND STEM AS ONE PIECE.
7、VALVES SHALL BE SUPPLIED WITH A DEVICE TO ENABLE THE VALVE TO BE LOCKED IN THE OPEN/CLOSED POSITION.
8、ALL GRAPHITE SEALS TO BE SUPPLIED WITH CORROSION INHIBITOR.

9、VALVES IN EXCESS OF 50KG TO INCLUDE FOR BALANCED LIFTING LUGS (FLANGES AND/OR TOP COVERS SHALL NOT BE USED) AND VALVES IN EXCESS
OF 100KG TO BE SUPPLIED WITH SUPPORT LEGS.

10、THE STEM MATERIAL SHALL BE SUFFICIENT INTENSITY TO MEET REQUIREMENTS OF VALVE TORQUE.
11、MANUFACTURE SHALL CHARGE OF ALL RESPONSIBILITY FOR MATAERIALS THAT PROPOSED BY MANUFACTURE.
12、MANUFACTURE SHALL CONSIDE OVER MATERIALS' GALVANIC CORROSION FOR ALL COMPONENTS.
13、THE SOFT MATERIAL FOR LIP SEAL, SEAT AND O RING SHALL BE USED UP TO 100℃.
14、VALVES DESIGN SHALL ALLOW FOR INSULATION BOXES.
15、PURCHASED QUANTITIES AND SIZE IN ACCORDANCE WITH MTO .
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 13 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB92ARN VALVE TYPE: BALL (RB), SOFT SEAT - NON SOUR PIPE CLASS : AN21
RATING: ASME B16.5 CL150 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN150 THRU DN350
GENERAL REQUIREMNETS & DETAILS (NOTE1) Rev. MATERIAL (NOTES 2 & 3) Rev.
DESIGN CONDITIONS MATERIAL ASME B16.34 /ASME B31.3
DESIGN PRESSURE Min.Fv Max.40 barg SERVICE/CORROSION NON SOUR SERVICE NACE
DESIGN TEMPERATURE ℃ Min.-15℃ Max.85℃ NON METALLIC MATERIAL SUITABLE FOR DESIGN CONDITIONS
SERVICE MEDIUMS CRUDE OIL
APPROVALS/CERTIFICATIONS (MANUFACTURE)
CE APPROVAL
ISO9001 APPROVAL
API API 6D
API 607 CERTIFIED OR API 6FA CERTIFIED
CORROSION ALLOWANCE 3 mm MATERIALS - WETTED COMPONENTS (NOTE 2 & 11)
TEST CRITERIA BODY/BODY COVER ASTM A105N
SHELL PRESSURE API 6D MATCH FLANGES (IF REQUIRED) ASTM A105N
BACK SEAT PRESSURE N/A OBTURATOR (BALL) ASTM A182 F316L
HYDROSTATIC SEAT TEST ACCEPTANCE AS PER ISO 5208 RATE A OBTURATOR RETAINER ASTM A182 F316L
LOW PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM (NOTE 10) ASTM A182 F6A /VTA*
HIGH PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM/TRUNN THRUST WASH ASTM A182 F316L
FUGITIVE EMISSIONS N/A STEM/TRUNN BUSH/BEARING ASTM A182 F316L
DESIGN CRETERIA (NOTES 2) STEM GLAND SEAL/PACKING LIP SEAL & GRAPHITE (NOTE 8 )
VALVE TYPE & STYLE DIB-2 TRUNNION MOUNTED BUSHING ASTM A182 F316L WITH PTFE
FLOW DIRECTION UNI-DIRECTIONAL SEAT RING ASTM A182 F316L
VALVE DESIGN API 6D SEAT INSERT FKM (NOTE 13)
BODY TYPE THREE PIECES LIP SEAL RPTFE + INCONEL X750 (NOTE 13)
BODY PATTERN LONG PATTERN O RINGS FKM (NOTE 13)
BORE (NOTE 5) REDUCED BORE GASKETS SW 316L / GRAPHITE FILLER
CRYOGENIC BONNET N/A SPRINGS INCONEL X750
OBTURATOR TYPE CONCENTRIC BALL STUD BOLTS & NUT ASTM A193 B7M/A194 2HM
OBTURATOR DESIGN SOLID BALL ONE PIECE DRAIN VALVES SEAT ASTM A182 F316L WITH SOFT SEAL
STEM DESIGN ASME B16.34 & API 6D DRAIN VALVES BODY ASTM A105N (NOTE 16)
ENERGIZED LIP SEAL + SINGLE WIPER +
STEM/BODY SEAL FIRESEAL
DRAIN PLUGS ASTM A105N (NOTE 16)
METAL SEAT RING WITH SOFT SEAT AS PER
SEAT DESIGN API 6D
SEAT RING/BODY SEAL LIP SEAL
BODY/COVER SEAL SPIRAL WOUND GASKET
STANDARDS & SPECIFICATIONS
CODE ASME B16.34 & API 6D
DESIGN & TESTING ASME B16.34 & API 6D
END TO END DIMENSIONS API 6D MATERIALS - NON WETTED COMPONENTS (NOTE 2)
BODY/BONNET TAPPING N/A MANUAL OPERATOR HAND WHEEL ASTM A216 WCB
FUGITIVE EMISSIONS N/A GEAR OPERATOR VTA*
OPERATOR YOKE ISO 5211 GLAND FLANGE ASTM A105N
MATERIAL CERTIFICATION PRESSURE PARTS - BS EN 10204 - 3.2 GLAND FOLLOWER SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
TRIM - BS EN 10204 - 3.1 SHAFT/SPINDLE/KEYS ATSM A276 T410 (H) (NOTE 1)
SAFETY LIFTING ATTACHMENTS ASTM A105N (NOTE9)
FLUID THERMAL EXPANSION ASME B16.34, NO DRILLING OF OBTURATOR ANTI-STATIC DEVICE ASTM A182 F316L
STEM RETENTION ASME B16.34 & API 6D STEM NUT ASTM A182 F6A*
ANTI STATIC API 6D MISC COMPONENTS SUITABLE FOR DESIGN TEMPS. *
FIRE SAFE API 607 CERTIFIED
OR API 6FA CERTIFIED
GENERAL:
PROJECT SPECIFICATION 1、THE DATASHEET SHALL BE COMPLETED AND ALL BLANKS WITH * SHALL
EBS1-AAAA00-MEPI-SPMT-1001 PIPNG AND VALVE MATERIAL BE ADVISED AND FILLED BY MANUFACTURER.
SPECIFICATION
2、ALL GENERAL AND NOTES SHALL BE COMPLIED.
EBS1-AAAA00-SAPI-SPMT-1090 BALL VALVE SPECIFICATION
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 14 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RB92ARN VALVE TYPE: BALL (RB), SOFT SEAT - NON SOUR PIPE CLASS : AN21
RATING: ASME B16.5 CL150 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN150 THRU DN350
NOTES:
1、ANY DEVIATION FROM THE DATA SHEET AND REFERENCE SPECIFICATIONS SHALL BE STATED AND APPROVED.
2、ALL MATERIALS (METALLIC & NON METALLIC) SHALL BE SUITABLE FOR THE FULL PRESSURE RATING OVER THE DESIGN TEMPERATURE RANGE.
3、ASBESTOS IS NOT ACCEPTABLE FOR ANY VALVE PARTS.
4、VALVE SHALL BE MARKED IN ACCODANCE WITH MSS-SP-25.
5、REDUCED BORE BALL VALVES SHALL BE SUPPLIED WITH ONE SIZE REDUCTION (IE DN100 X DN80) IF REQUIRED.
6、BALL VALVES SHALL NOT BE SUPPLIED WITH BALL AND STEM AS ONE PIECE.
7、VALVES SHALL BE SUPPLIED WITH A DEVICE TO ENABLE THE VALVE TO BE LOCKED IN THE OPEN/CLOSED POSITION.
8、ALL GRAPHITE SEALS TO BE SUPPLIED WITH CORROSION INHIBITOR.

9、VALVES IN EXCESS OF 50KG TO INCLUDE FOR BALANCED LIFTING LUGS (FLANGES AND/OR TOP COVERS SHALL NOT BE USED) AND VALVES IN EXCESS
OF 100KG TO BE SUPPLIED WITH SUPPORT LEGS.

10、THE STEM MATERIAL SHALL BE SUFFICIENT INTENSITY TO MEET REQUIREMENTS OF VALVE TORQUE.
11、MANUFACTURE SHALL CHARGE OF ALL RESPONSIBILITY FOR MATAERIALS THAT PROPOSED BY MANUFACTURE.
12、MANUFACTURE SHALL CONSIDE OVER MATERIALS' GALVANIC CORROSION BETWEEN TRUNNION AND BUSHING.
13、THE SOFT MATERIAL FOR LIP SEAL, SEAT INSERT AND O RING SHALL BE USED UP TO 100℃.
14、VALVES DESIGN SHALL ALLOW FOR INSULATION BOXES.
15、PURCHASED QUANTITIES AND SIZE IN ACCORDANCE WITH MTO .

16、FOR BALL VALVES WITH DIMENSION ARE GREATER THAN DN80 (INCLUDE DN80) SHALL BE FITTED WITH DRAIN VALVE.

17、THE VALVE BODY SHALL BE FURNISHED WITH A ARROW TO INDICATE THE DIRECTIONA OF FLOW THROUG THE VALVE.
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 15 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RBH2ARN VALVE TYPE: BALL (FB), SOFT SEAT -NON SOUR PIPE CLASS : AN21
RATING: ASME B16.5 CL150 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN50 THRU DN350
GENERAL REQUIREMNETS & DETAILS (NOTE1) Rev. MATERIAL (NOTES 2 & 3) Rev.
DESIGN CONDITIONS MATERIAL ASME B16.34 /ASME B31.3
DESIGN PRESSURE Min.Fv Max.40 barg SERVICE/CORROSION NON SOUR SERVICE NACE
DESIGN TEMPERATURE ℃ Min.-15℃ Max.85℃ NON METALLIC MATERIAL SUITABLE FOR DESIGN CONDITIONS
SERVICE MEDIUMS CRUDE OIL
APPROVALS/CERTIFICATIONS (MANUFACTURE)
CE APPROVAL
ISO9001 APPROVAL
API API 6D
API 607 CERTIFIED OR API 6FA CERTIFIED
CORROSION ALLOWANCE 3 mm MATERIALS - WETTED COMPONENTS (NOTE 2 & 11)
TEST CRITERIA BODY/BODY COVER ASTM A105N
SHELL PRESSURE API 6D MATCH FLANGES (IF REQUIRED) ASTM A105N
BACK SEAT PRESSURE N/A OBTURATOR (BALL) ASTM A182 F316L
HYDROSTATIC SEAT TEST ACCEPTANCE AS PER ISO 5208 RATE A OBTURATOR RETAINER ASTM A182 F316L
LOW PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM (NOTE 10) ASTM A182 F6A /VTA*
HIGH PRESSURE CLOSURE AS PER ISO 5208 RATE A STEM/TRUNN THRUST WASH ASTM A182 F316L
FUGITIVE EMISSIONS N/A STEM/TRUNN BUSH/BEARING ASTM A182 F316L
DESIGN CRETERIA (NOTES 2) STEM GLAND SEAL/PACKING LIP SEAL & GRAPHITE (NOTE 8 )
VALVE TYPE & STYLE DIB-2 TRUNNION MOUNTED BUSHING ASTM A182 F316L WITH PTFE
FLOW DIRECTION UNI-DIRECTIONAL SEAT RING ASTM A182 F316L
VALVE DESIGN API 6D SEAT INSERT FKM (NOTE 13)
BODY TYPE THREE PIECES LIP SEAL RPTFE +INCONEL X750 (NOTE 13)
BODY PATTERN LONG PATTERN O RINGS FKM (NOTE 13)
BORE (NOTE 5) FULL BORE GASKETS SW 316L / GRAPHITE FILLER
CRYOGENIC BONNET N/A SPRINGS INCONEL X750
OBTURATOR TYPE CONCENTRIC BALL STUD BOLTS & NUT ASTM A193 B7M/A194 2HM
OBTURATOR DESIGN SOLID BALL ONE PIECE DRAIN VALVES SEAT ASTM A182 F316L WITH SOFT SEAL
STEM DESIGN ASME B16.34 & API 6D DRAIN VALVES BODY ASTM A105N (NOTE 16)
ENERGIZED LIP SEAL + SINGLE WIPER +
STEM/BODY SEAL FIRESEAL
DRAIN PLUGS ASTM A105N (NOTE 16)
METAL SEAT RING WITH SOFT SEAT AS PER
SEAT DESIGN API 6D
SEAT RING/BODY SEAL LIP SEAL
BODY/COVER SEAL SPIRAL WOUND GASKET
STANDARDS & SPECIFICATIONS
CODE ASME B16.34 & API 6D
DESIGN & TESTING ASME B16.34 & API 6D
END TO END DIMENSIONS API 6D MATERIALS - NON WETTED COMPONENTS (NOTE 2)
BODY/BONNET TAPPING N/A MANUAL OPERATOR HAND WHEEL ASTM A216 WCB
FUGITIVE EMISSIONS N/A GEAR OPERATOR VTA*
OPERATOR YOKE ISO 5211 GLAND FLANGE ASTM A105N
MATERIAL CERTIFICATION PRESSURE PARTS - BS EN 10204 - 3.2 GLAND FOLLOWER SUITABLE FOR DESIGN TEMPS. * (NOTE 1)
TRIM - BS EN 10204 - 3.1 SHAFT/SPINDLE/KEYS ATSM A276 T410 (H) (NOTE 1)
SAFETY LIFTING ATTACHMENTS ASTM A105N (NOTE9)
FLUID THERMAL EXPANSION ASME B16.34, NO DRILLING OF OBTURATOR ANTI-STATIC DEVICE ASTM A182 F316L
STEM RETENTION ASME B16.34 & API 6D STEM NUT ASTM A182 F6A*
ANTI STATIC API 6D MISC COMPONENTS SUITABLE FOR DESIGN TEMPS. *
FIRE SAFE API 607 CERTIFIED
OR API 6FA CERTIFIED
GENERAL:
PROJECT SPECIFICATION 1、THE DATASHEET SHALL BE COMPLETED AND ALL BLANKS WITH * SHALL
EBS1-AAAA00-MEPI-SPMT-1001 PIPNG AND VALVE MATERIAL BE ADVISED AND FILLED BY MANUFACTURER.
SPECIFICATION
2、ALL GENERAL AND NOTES SHALL BE COMPLIED.
EBS1-AAAA00-SAPI-SPMT-1090 BALL VALVE SPECIFICATION
 PIPELINE CORRIDOR FROM
FPF TO CPF

Ball Valve PROJECT SCOPE DISPL DOC SEQ REV

Page 16 of 16
(3/4"~14")Data Sheets EBS1 FPFA00 SAPI DSVL 1022 D00

VALVE CODE NUMBER: RBH2ARN VALVE TYPE: BALL (FB), SOFT SEAT -NON SOUR PIPE CLASS : AN21
RATING: ASME B16.5 CL150 ENDS: FLANGED RAISED FACE (ASME B16.5 125/250AARH) SIZE RANGE: DN50 THRU DN350
NOTES:
1、ANY DEVIATION FROM THE DATA SHEET AND REFERENCE SPECIFICATIONS SHALL BE STATED AND APPROVED.
2、ALL MATERIALS (METALLIC & NON METALLIC) SHALL BE SUITABLE FOR THE FULL PRESSURE RATING OVER THE DESIGN TEMPERATURE RANGE.
3、ASBESTOS IS NOT ACCEPTABLE FOR ANY VALVE PARTS.
4、VALVE SHALL BE MARKED IN ACCODANCE WITH MSS-SP-25.
5、FULL BORE BALL VALVES SHALL BE SUPPLIED ACCORDING TO API 6D REQUIREMENTS..
6、BALL VALVES SHALL NOT BE SUPPLIED WITH BALL AND STEM AS ONE PIECE.
7、VALVES SHALL BE SUPPLIED WITH A DEVICE TO ENABLE THE VALVE TO BE LOCKED IN THE OPEN/CLOSED POSITION.
8、ALL GRAPHITE SEALS TO BE SUPPLIED WITH CORROSION INHIBITOR.

9、VALVES IN EXCESS OF 50KG TO INCLUDE FOR BALANCED LIFTING LUGS (FLANGES AND/OR TOP COVERS SHALL NOT BE USED) AND VALVES IN EXCESS
OF 100KG TO BE SUPPLIED WITH SUPPORT LEGS.

10、THE STEM MATERIAL SHALL BE SUFFICIENT INTENSITY TO MEET REQUIREMENTS OF VALVE TORQUE.
11、MANUFACTURE SHALL CHARGE OF ALL RESPONSIBILITY FOR MATAERIALS THAT PROPOSED BY MANUFACTURE.
12、MANUFACTURE SHALL CONSIDE OVER MATERIALS' GALVANIC CORROSION BETWEEN TRUNNION AND BUSHING.
13、THE SOFT MATERIAL FOR LIP SEAL,SEAT INSERT AND O RING SHALL BE USED UP TO 100℃.
14、VALVES DESIGN SHALL ALLOW FOR INSULATION BOXES.
15、PURCHASED QUANTITIES AND SIZE IN ACCORDANCE WITH MTO .

16、FOR BALL VALVES WITH DIMENSION ARE GREATER THAN DN80 (INCLUDE DN80) SHALL BE FITTED WITH DRAIN VALVE. THE OTHER DIMENSION SHALL
BE FITTED WITH DRAIN PLUG.

17、THE VALVE BODY SHALL BE FURNISHED WITH A ARROW TO INDICATE THE DIRECTIONA OF FLOW THROUG THE VALVE.