Digital Outputs 0-5 are parallel to Relay Outputs 0-5

GND
POWER
CONTROLLINO Function
PHYSICAL PIN

A4
A5
PORT PIN
8
9

4
5
6
7
8
9
RTC ARDUINO UNO Board

Nominal load current = 2A (self limiting)

10 PB2 14 RTC SS CE General Information

8 x HIGH CURRENT High Side Switch

Operational Voltage:
13 PB5 17 SCK SCL

PD4
PD5
PD6
PD7
PB0
PB1

PB0
PB1
PC4
PC5
12V: 10,8V-13,2V
Resistive Load max. current

On-state resistance = typ 70mΩ

24V: 21,6V-26,4V 11 PB3 15 MOSI SDI Pay attention
6A 250V AC / 30V DC 6A

12 PB4 16 MISO SDO

Max. 8A CHIP used ATmega 328P-AU
12
13

10
11
12
13
27
28
2
9
(Fused by not resettable fuse)
/INT
Relay output

RV-2123-C2-TA-QC-020

Digital 6
Digital 7
Digital 0
Digital 1
Digital 2
Digital 3
Digital 4
Digital 5
Relay 4
Relay 5

/Reset
GND
VIN

Not proper handling of the RTC /INT output

can cause permanent Controllino reset

Digital OUTPUT D0-D5: Pin Header Output

ESD
Protection

Vin
Protection resistor

ATmega ESD Screw Terminal Pin Header current limit:

MINI
HighSide Switch
Output Port Protection Power Output
Absolute max per pin 40mA
recommended 20mA
Screw Terminal
Relay Absolute max 200mA
Power Output
for entire Pin Header
Current limit @5V + 3V3 max

Digital OUTPUT D6, D7: Pin Header Output

200mA (Fused by resettable fuse)
Current limit @3V3 only 150mA
All signals are protected with serial
PINOUT V1.1
ESD resistance
Protection

Vin
Protection resistor

ATmega ESD Screw Terminal

HighSide Switch
Output Port Protection Power Output 1
Attention to current limit 5V GND
A0 PC0 23 Analog 0 Analog 1 24 PC1 A1
Logic “1” level: 9V – 13,2V (Vin=12V), 18V–26,4V (Vin=24V)

A2 PC2 25 Analog 2 Analog 3 26 PC3 A3

Logic “0” level: 0V – 3,6V (Vin=12V), 0V–7,2V (Vin=24V)

Interrupt 0
Interrupt 1
A6 ADC6 19 Analog 4 Analog 5 22 ADC7 A7
Analog 0
Analog 1
Analog 2
Analog 3
Analog 4
Analog 5
Relay 2
Relay 3
Relay 0
Relay 1

2 PD2 32 Interrupt 0 Interrupt 1 1 PD3 3

Resistive Load max. current

RESET /RESET 29 /Reset Digital 01 2 PD4 4

6A 250V AC / 30V DC 6A

0 – 13,2V (Vin=12V) / 0 – 26,4V (Vin=24V)

Voltage range in case of analog input use

Analog/Digital INPUT: Pin Header Input 5 PD5 9 Digital 1 Digital 2 10 PD6 6

7 PD7 11 Digital 3 Digital 4 12 PB0 8
10
11

23
24
25
26
19
22
32
1
2
9
Relay output

9 PB1 13 Digital 5
Maximum input current <3mA

ESD Digital 6 / SDA 27 PC4 A4

Protection
A5 PC5 28 Digital 7 / SCL /SS 14 PB2 10
ADC6
ADC7
PD6
PD7

PD2
PD3
PC0
PC1
PC2
PC3
PD4
PD5

Protection resistor 11 PB3 15 MOSI MISO 16 PB4 12

13 PB5 17 SCK 3V3 Attention to current limit
Automatic divider
Signal Inputs

Screw terminal Division ratio: ESD ATmega TX 1 PD1 31 TXD RXD 30 PD0 RX 0
input 12V range: 3,06 Protection Input Port Connected to the ATmega16u2 and
X1
A0
A1
A2
A3
A6
A7
6
7

2
3
4
5

24V range: 6,14 used for USB programming and

communication with PC

A4 + A5 only Analog Inputs